![header thumbnail](/images/publishers\iso_cover.gif)
ISO 604:2002
Current
The latest, up-to-date edition.
![header thumbnail](/images/publishers\iso_cover.gif)
Plastics — Determination of compressive properties
Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users
English, French
07-03-2002
This International Standard specifies a method for determining the compressive properties of plastics under defined
conditions. A standard test specimen is defined but its length may be adjusted to prevent buckling under load from
affecting the results. A range of test speeds is included.
The method is used to investigate the compressive behaviour of the test specimens and for determining the
compressive strength, compressive modulus and other aspects of the compressive stress/strain relationship under
the conditions defined.
The method applies to the following range of materials:
rigid and semi-rigid [1] thermoplastic moulding and extrusion materials, including compounds filled and
reinforced by e.g. short fibres, small rods, plates or granules in addition to unfilled types; rigid and semi-rigid
thermoplastic sheet;
rigid and semi-rigid thermoset moulding materials, including filled and reinforced compounds; rigid and semirigid
thermoset sheet;
thermotropic liquid-crystal polymers.
In agreement with ISO 10350-1 and ISO 10350-2, this International Standard applies to fibre-reinforced
compounds with fibre lengths u 7,5 mm prior to processing.
The method is not normally suitable for use with materials reinforced by textile fibres (see references [2] and [5]),
fibre-reinforced plastic composites and laminates (see [5]), rigid cellular materials (see [3]) or sandwich structures
containing cellular material or rubber (see [4]).
The method is performed using specimens which may be moulded to the chosen dimensions, machined from the
central portion of a standard multipurpose test specimen (see ISO 3167) or machined from finished or semifinished
products such as mouldings or extruded or cast sheet.
The method specifies preferred dimensions for the test specimen. Tests which are carried out on specimens of
different dimensions, or on specimens which are prepared under different conditions, may produce results which
are not comparable. Other factors, such as the test speed and the conditioning of the specimens, can also
influence the results. Consequently, when comparable data are required, these factors must be carefully controlled
and recorded.
DevelopmentNote |
Supersedes ISO/FDIS 604 (04/2002)
|
DocumentType |
Standard
|
Pages |
18
|
PublisherName |
International Organization for Standardization
|
Status |
Current
|
Supersedes |
Standards | Relationship |
NEN EN ISO 604 : 2003 | Identical |
UNE 53189-4:1975 | Identical |
UNE-EN ISO 604:2003 | Identical |
NF EN ISO 604 : 2004 | Identical |
NBN EN ISO 604 : 2003 | Identical |
EN ISO 604 : 2003 | Identical |
DIN EN ISO 604 E : 2003 | Identical |
UNI EN ISO 604 : 2008 | Identical |
I.S. EN ISO 604:2003 | Identical |
DIN EN ISO 604:2003-12 | Identical |
PN EN ISO 604 : 2006 | Identical |
SN EN ISO 604 : 2003 | Identical |
BS EN ISO 604:2003 | Identical |
BIS IS 13360-5-8 : 2013 | Identical |
NS EN ISO 604 : 2ED 2003 | Identical |
NF ISO 604 : 1994 | Identical |
BS 2782-3.345A(1993) : 1993 AMD 8637 | Identical |
UNE 104424:2015 | Synthetic materials. Application. Waterproofing lining systems for tunnels and galleries made out of manufactured thermoplastic sheets of PVC-P |
I.S. EN 15383:2012 | PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON POLYESTER RESIN (UP) - MANHOLES AND INSPECTION CHAMBERS |
13/30263803 DC : 0 | BS ISO 17296-4 - ADDITIVE MANUFACTURING - RAPID TECHNOLOGIES (RAPID PROTOTYPING) - PART 4: DATA PROCESSING |
ISO 25780:2011 | Plastics piping systems for pressure and non-pressure water supply, irrigation, drainage or sewerage — Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin — Pipes with flexible joints intended to be installed using jacking techniques |
DIN EN 15383:2014-02 | PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON POLYESTER RESIN (UP) - MANHOLES AND INSPECTION CHAMBERS |
BS ISO 13586 : 2000 | PLASTICS - DETERMINATION OF FRACTURE TOUGHNESS (G[IC] AND K[IC]) - LINEAR ELASTIC FRACTURE MECHANICS (LEFM) APPROACH |
BS ISO 20753 : 2008 | PLASTICS - TEST SPECIMENS |
PREN 13160-7 : DRAFT 2014 | LEAK DETECTION SYSTEMS - PART 7: REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR INTERSTITIAL SPACES, LEAK DETECTION LININGS AND LEAK DETECTION JACKETS |
API RP 17B : 2014 | RECOMMENDED PRACTICE FOR FLEXIBLE PIPE |
SAE AMS 2950/1 : 2008 | PASTE ADHESIVE FOR CORE RESTORATION - PART 1: GENERAL REQUIREMENTS |
IEC 60893-2:2003 | Industrial rigid laminated sheets based on thermosetting resins for electrical purposes - Part 2: Methods of test |
DIN EN ISO 20753 E : 2014 | PLASTICS - TEST SPECIMENS (ISO 20753:2008) |
UNI EN 15383 : 2013-11 | PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON POLYESTER RESIN (UP) - MANHOLES AND INSPECTION CHAMBERS |
ASTM D 5927 : 2017 : REDLINE | Standard Classification System for and Basis for Specifications for Thermoplastic Polyester (TPES) Injection and Extrusion Materials Based on ISO Test Methods |
ASTM D 5592 : 1994 | Standard Guide for Material Properties Needed in Engineering Design Using Plastics |
DIN EN ISO 20753:2014-07 | PLASTICS - TEST SPECIMENS (ISO 20753:2008) |
DIN EN ISO 8257-2 E : 2006 | PLASTICS - POLY(METHYL METHACRYLATE) (PMMA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
BS EN ISO 13628-2:2006 | Petroleum and natural gas industries. Design and operation of subsea production systems Unbonded flexible pipe systems for subsea and marine applications |
BS EN ISO 11248:2000 | Plastics. Thermosetting moulding materials. Evaluation of short-term performance at elevated temperatures |
IEC 62011-2:2004 | Insulating materials - Industrial, rigid, moulded, laminated tubes and rods of rectangular and hexagonal cross-section, based on thermosetting resins for electrical purposes - Part 2: Methods of test |
ISO 13628-11:2007 | Petroleum and natural gas industries — Design and operation of subsea production systems — Part 11: Flexible pipe systems for subsea and marine applications |
BS EN ISO 3167:2014 | Plastics. Multipurpose test specimens |
BS EN 60893-2:2004 | Insulating materials. Industrial rigid laminated sheets based on thermosetting resins for electrical purposes Methods of test |
DIN EN ISO 8257-2:2006-06 | PLASTICS - POLY(METHYL METHACRYLATE) (PMMA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
EN 62011-2:2004 | Insulating materials - Industrial, rigid, moulded, laminated tubes and rods of rectangular and hexagonal cross-section, based on thermosetting resins for electrical purposes - Part 2: Methods of test |
DIN EN ISO 3672-2:2002-07 | PLASTICS - UNSATURATED-POLYESTER RESINS (UP-R) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
EN 13160-7:2016 | Leak detection systems - Part 7: Requirements and test/assessment methods for interstitial spaces, leak detection linings and leak detection jackets |
EN 60893-2:2004 | Insulating materials - Industrial rigid laminated sheets based on thermosetting resins for electrical purposes - Part 2: Methods of test |
BS 2782-1.136(1994) : 1994 AMD 10687 | METHODS OF TESTING PLASTICS - THERMAL PROPERTIES - DETERMINATION OF THE SHORT-TERM PERFORMANCE OF THERMOSETTING MOULDING MATERIALS AT ELEVATED TEMPERATURES |
BS EN 50617-1:2015 | Railway applications. Technical parameters of train detection systems for the interoperability of the trans-European railway system Track circuits |
16/30340787 DC : 0 | BS ISO 13586 - PLASTICS - DETERMINATION OF FRACTURE TOUGHNESS (GIC AND KIC) - LINEAR ELASTIC FRACTURE MECHANICS (LEFM) APPROACH |
BS 2782-3 Method 345A:1979 | Methods of testing plastics. Mechanical properties Determination of compressive properties by deformation at constant rate |
05/30132990 DC : DRAFT APR 2005 | ISO 20753 - PLASTICS - TEST SPECIMENS |
10/30237537 DC : 0 | EN 15383 - PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON POLYESTER RESIN (UP) - MANHOLES AND INSPECTION CHAMBERS |
PREN 13411-4 : DRAFT 2009 | TERMINATIONS FOR STEEL WIRE ROPES - SAFETY - PART 4: METAL RESIN SOCKETING |
BS ISO 12891-2:2014 | Retrieval and analysis of surgical implants Analysis of retrieved surgical implants |
14/30301266 DC : 0 | BS EN 13160-7 - LEAK DETECTION SYSTEMS - PART 7: REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR INTERSTITIAL SPACES, LEAK DETECTION LININGS AND LEAK DETECTION JACKETS |
ISO 20753:2008 | Plastics Test specimens |
08/30138102 DC : DRAFT MAR 2008 | BS ISO 25780 - PLASTICS PIPING SYSTEMS FOR PRESSURE AND NON-PRESSURE WATER SUPPLY, IRRIGATION, DRAINAGE OR SEWERAGE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) SYSTEMS BASED ON UNSATURATED POLYESTER (UP) RESIN - PIPES WITH FLEXIBLE JOINTS INTENDED TO BE INSTALLED USING JACKING TECHNIQUES |
BS ISO 8257-2:1990 | Plastics. Poly(methyl methacrylate) (PMMA) moulding and extrusion materials Preparation of test specimens and determination of properties |
09/30198357 DC : 0 | BS EN 13411-4 - TERMINATIONS FOR STEEL WIRE ROPES - SAFETY - PART 4: METAL RESIN SOCKETING |
API 17L1 : 2013 | SPECIFICATION FOR FLEXIBLE PIPE ANCILLARY EQUIPMENT |
ISO 19213:2017 | Implants for surgery — Test methods of material for use as a cortical bone model |
AAMI TIR17 : 2017 | COMPATIBILITY OF MATERIALS SUBJECT TO STERILIZATION |
BS EN ISO 20753:2014 | Plastics. Test specimens |
ASTM D 4000 : 2016 : REDLINE | Standard Classification System for Specifying Plastic Materials |
ISO 8606:1990 | Plastics — Prepregs — Bulk moulding compound (BMC) and dough moulding compound (DMC) — Basis for a specification |
I.S. EN ISO 13628-2:2006 | PETROLEUM AND NATURAL GAS INDUSTRIES - DESIGN AND OPERATION OF SUBSEA PRODUCTION SYSTEMS - PART 2: UNBONDED FLEXIBLE PIPE SYSTEMS FOR SUBSEA AND MARINE APPLICATIONS |
I.S. EN 13160-7:2016 | LEAK DETECTION SYSTEMS - PART 7: REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR INTERSTITIAL SPACES, LEAK DETECTION LININGS AND LEAK DETECTION JACKETS |
I.S. EN 61212-2:2006 | INSULATING MATERIALS - INDUSTRIAL RIGID ROUND LAMINATED TUBES AND RODS BASED ON THERMOSETTING RESINS FOR ELECTRICAL PURPOSES - PART 2: METHODS OF TEST |
I.S. EN ISO 3167:2014 | PLASTICS - MULTIPURPOSE TEST SPECIMENS (ISO 3167:2014) |
I.S. EN 60893-2:2004 | INSULATING MATERIALS - INDUSTRIAL RIGID LAMINATED SHEETS BASED ON THERMOSETTING RESINS FOR ELECTRICAL PURPOSES - PART 2: METHODS OF TEST |
I.S. EN ISO 8257-2:2006 | PLASTICS - POLY(METHYL METHACRYLATE) (PMMA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
I.S. EN 13411-4:2011 | TERMINATIONS FOR STEEL WIRE ROPES - SAFETY - PART 4: METAL AND RESIN SOCKETING |
UNI EN 13411-4 : 2011 | TERMINATIONS FOR STEEL WIRE ROPES - SAFETY - PART 4: METAL AND RESIN SOCKETING |
VDI 3388:2012-03 | Materials for trimming and forming dies |
BS 4936:1987 | Method of specifying styrene-acrylonitrile (SAN) moulding and extrusion materials |
BS 1493:1987 | Method of specifying general purpose polystyrene (PS) moulding and extrusion materials |
ASME PCC 2 : 2015 | REPAIR OF PRESSURE EQUIPMENT AND PIPING |
PD CEN/TR 14548:2003 | Adhesives. Guide to test methods and other standards for the general requirements, characterization and safety of structural adhesives |
BS ISO 13781:2017 | Implants for surgery. Homopolymers, copolymers and blends on poly(lactide). In vitro degradation testing |
BS ISO 25780:2011 | Plastics piping systems for pressure and non-pressure water supply, irrigation, drainage or sewerage. Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin. Pipes with flexible joints intended to be installed using jacking techniques |
BS EN ISO 17296-3:2016 | Additive manufacturing. General principles Main characteristics and corresponding test methods |
BS ISO 3672-2 : 2000 AMD 13326 | PLASTICS - UNSATURATED-POLYESTER RESINS (UP-R) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
CEI EN 62011-2 : 2005 | INSULATING MATERIALS - INDUSTRIAL, RIGID, MOULDED, LAMINATED TUBES AND RODS OF RECTANGULAR AND HEXAGONAL CROSS-SECTION, BASED ON THERMOSETTING RESINS FOR ELECTRICAL PURPOSES - PART 2: METHODS OF TEST |
ISO 13781:2017 | Implants for surgery — Homopolymers, copolymers and blends on poly(lactide) — In vitro degradation testing |
I.S. EN 60455-2:2015 | RESIN BASED REACTIVE COMPOUNDS USED FOR ELECTRICAL INSULATION - PART 2: METHODS OF TEST |
ISO 12856-1:2014 | Plastics Plastic railway sleepers for railway applications (railroad ties) Part 1: Material characteristics |
I.S. EN ISO 13628-11:2008 | PETROLEUM AND NATURAL GAS INDUSTRIES - DESIGN AND OPERATION OF SUBSEA PRODUCTION SYSTEMS - PART 11: FLEXIBLE PIPE SYSTEMS FOR SUBSEA AND MARINE APPLICATIONS |
AAMI TIR17 : 2008 | COMPATIBILITY OF MATERIALS SUBJECT TO STERILIZATION |
ASTM D 695 : 2015 : REDLINE | Standard Test Method for Compressive Properties of Rigid Plastics |
ASTM D 5138 : 2016 : REDLINE | Standard Classification System and Basis for Specification for Liquid Crystal Polymers Molding and Extrusion Materials (LCP) |
ASTM D 5857 : 2017 : REDLINE | Standard Specification for Polypropylene Injection and Extrusion Materials Using ISO Protocol and Methodology |
ASTM D 5936 : 1996 | Specification for Multipurpose Test Specimens (Withdrawn 1998) |
UNE-EN 13411-4:2011 | Terminations for steel wire ropes - Safety - Part 4: Metal and resin socketing |
UNE-EN 13160-7:2017 | Leak detection systems - Part 7: Requirements and test/assessment methods for interstitial spaces, leak detection linings and leak detection jackets |
DIN EN ISO 3672-2 E : 2002 | PLASTICS - UNSATURATED-POLYESTER RESINS (UP-R) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
EN ISO 13628-2:2006/AC:2009 | PETROLEUM AND NATURAL GAS INDUSTRIES - DESIGN AND OPERATION OF SUBSEA PRODUCTION SYSTEMS - PART 2: UNBONDED FLEXIBLE PIPE SYSTEMS FOR SUBSEA AND MARINE APPLICATIONS |
DIN EN 13411-4 E : 2011 | TERMINATIONS FOR STEEL WIRE ROPES - SAFETY - PART 4: METAL AND RESIN SOCKETING |
UNI EN ISO 3167 : 2014 | PLASTICS - MULTIPURPOSE TEST SPECIMENS |
ONORM EN 13411-4 : 2011 | TERMINATIONS FOR STEEL WIRE ROPES - SAFETY - PART 4: METAL AND RESIN SOCKETING |
UNI EN ISO 13628-2 : 2007 | PETROLEUM AND NATURAL GAS INDUSTRIES - DESIGN AND OPERATION OF SUBSEA PRODUCTION SYSTEMS - PART 2: UNBONDED FLEXIBLE PIPE SYSTEMS FOR SUBSEA AND MARINE APPLICATIONS |
I.S. EN ISO 14126:2000 | FIBRE-REINFORCED PLASTIC COMPOSITES - DETERMINATION OF COMPRESSIVE PROPERTIES IN THE IN-PLANE DIRECTION |
UNI EN ISO 13628-11 : 2008 | PETROLEUM AND NATURAL GAS INDUSTRIES - DESIGN AND OPERATION OF SUBSEA PRODUCTION SYSTEMS - PART 11: FLEXIBLE PIPE SYSTEMS FOR SUBSEA AND MARINE APPLICATIONS |
BS 6091-2:1987 | Vulcanized fibre for electrical purposes Methods of test |
10/30191247 DC : DRAFT APR 2010 | BS EN ISO 13628-16 - PETROLEUM AND NATURAL GAS INDUSTRIES - DESIGN AND OPERATION OF SUBSEA PRODUCTION SYSTEMS - PART 16: SPECIFICATION FOR FLEXIBLE PIPE ANCILLARY EQUIPMENT |
DIN EN 15383 E : 2014 | PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON POLYESTER RESIN (UP) - MANHOLES AND INSPECTION CHAMBERS |
UNE-EN 50617-1:2015 | Railway applications - Technical parameters of train detection systems for the interoperability of the trans-European railway system - Part 1: Track circuits |
BS EN 60455-2:2015 | Resin based reactive compounds used for electrical insulation Methods of test |
BS 7825-3.3:1997 | Calibration of rubber and plastics test equipment. Calibration schedules Mechanical properties of plastics |
15/30296854 DC : 0 | BS ISO 13781 - INPLANTS FOR SURGERY - HOMOPOLYMERS, COPOLYMERS AND BLENDS ON POLY(LACTIDE) - IN VITRO DEGRADATION TESTING |
BS EN 15383 : 2012 | PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON POLYESTER RESIN (UP) - MANHOLES AND INSPECTION CHAMBERS |
13/30242622 DC : 0 | BS ISO 12891-2 - RETRIEVAL AND ANALYSIS OF SURGICAL IMPLANTS - PART 2: ANALYSIS OF RETRIEVED SURGICAL IMPLANTS |
ISO 12891-2:2014 | Retrieval and analysis of surgical implants Part 2: Analysis of retrieved surgical implants |
ISO 13586:2000 | Plastics Determination of fracture toughness (GIC and KIC) Linear elastic fracture mechanics (LEFM) approach |
ASTM F 2820 : 2012 | Standard Specification for Polyetherketoneketone (PEKK) Polymers for Surgical Implant Applications |
BS ISO 19213:2017 | Implants for surgery. Test methods of material for use as a cortical bone model |
API 17J REDLINE : 2008 | SPECIFICATION FOR UNBONDED FLEXIBLE PIPE |
UNI EN ISO 20753 : 2014 | PLASTICS - TEST SPECIMENS |
API 17B REDLINE : 2008 | RECOMMENDED PRACTICE FOR FLEXIBLE PIPE |
I.S. CEN TR 14548:2003 | ADHESIVES - GUIDE TO TEST METHODS AND OTHER STANDARDS FOR THE GENERAL REQUIREMENTS, CHARACTERIZATION AND SAFETY OF STRUCTURAL ADHESIVES |
I.S. EN ISO 20753:2014 | PLASTICS - TEST SPECIMENS (ISO 20753:2008) |
SAE AMS 2950/1 : 2008(R2019) | PASTE ADHESIVE FOR CORE RESTORATION - PART 1: GENERAL REQUIREMENTS |
ASTM D 5592 : 1994 : R2010 | Standard Guide for Material Properties Needed in Engineering Design Using Plastics |
EN ISO 20753:2014 | PLASTICS - TEST SPECIMENS (ISO 20753:2008) |
ISO 6721-12:2009 | Plastics Determination of dynamic mechanical properties Part 12: Compressive vibration Non-resonance method |
DIN EN ISO 3167:2014-11 | PLASTICS - MULTIPURPOSE TEST SPECIMENS (ISO 3167:2014) |
BS EN ISO 14126:1999 | Fibre-reinforced plastic composites. Determination of compressive properties in the in-plane direction |
BS EN 13160-7:2003 | Leak detection systems General requirements and test methods for interstitial spaces, leak protecting linings and leak protecting jackets |
BS EN ISO 3672-2:2001 | Plastics. Unsaturated-polyester resins (UP-R) Preparation of test specimens and determination of properties |
IEC 60455-2:2015 | Resin based reactive compounds used for electrical insulation - Part 2: Methods of test |
ISO 8257-2:2001 | Plastics Poly(methyl methacrylate) (PMMA) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
IEC 61212-2:2006 | Insulating materials - Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes - Part 2: Methods of test |
ISO 3672-2:2000 | Plastics — Unsaturated-polyester resins (UP-R) — Part 2: Preparation of test specimens and determination of properties |
BS EN 13411-4:2011 | Terminations for steel wire ropes. Safety Metal and resin socketing |
BS EN ISO 8257-2:2006 | Plastics. Poly(methyl methacrylate) (PMMA) moulding and extrusion materials Preparation of test specimens and determination of properties |
UNE EN 15383 : 0 | PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON POLYESTER RESIN (UP) - MANHOLES AND INSPECTION CHAMBERS |
ISO 3167:2014 | Plastics Multipurpose test specimens |
ISO 17296-3:2014 | Additive manufacturing — General principles — Part 3: Main characteristics and corresponding test methods |
ISO 14126:1999 | Fibre-reinforced plastic composites — Determination of compressive properties in the in-plane direction |
UNE-EN ISO 3167:2014 | Plastics - Multipurpose test specimens (ISO 3167:2014) |
ISO 13628-2:2006 | Petroleum and natural gas industries Design and operation of subsea production systems Part 2: Unbonded flexible pipe systems for subsea and marine applications |
EN ISO 8257-2:2006 | Plastics - Poly(methyl methacrylate) (PMMA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 8257-2:2001) |
EN ISO 3167:2014 | Plastics - Multipurpose test specimens (ISO 3167:2014) |
EN ISO 3672-2 : 2001 | PLASTICS - UNSATURATED-POLYESTER RESINS (UP-R) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
EN ISO 14126:1999/AC:2002 | FIBRE-REINFORCED PLASTIC COMPOSITES - DETERMINATION OF COMPRESSIVE PROPERTIES IN THE IN-PLANE DIRECTION |
EN 15383:2012+A1:2013 | Plastics piping systems for drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) - Manholes and inspection chambers |
EN ISO 11248 : 1999 | Plastics - Thermosetting moulding materials - Evaluation of short-term performance at elevated temperatures (ISO 11248:1993) |
EN ISO 17296-3:2016 | Additive manufacturing - General principles - Part 3: Main characteristics and corresponding test methods (ISO 17296-3:2014) |
BS ISO 17296-3 : 2014 | ADDITIVE MANUFACTURING - GENERAL PRINCIPLES - PART 3: MAIN CHARACTERISTICS AND CORRESPONDING TEST METHODS |
I.S. EN 62011-2:2004 | INSULATING MATERIALS - INDUSTRIAL, RIGID, MOULDED, LAMINATED TUBES AND RODS OF RECTANGULAR AND HEXAGONAL CROSS-SECTION, BASED ON THERMOSETTING RESINS FOR ELECTRICAL PURPOSES, - PART 2: METHODS OF TEST |
CEI EN 60893-2 : 2005 | INSULATING MATERIALS - INDUSTRIAL RIGID LAMINATED SHEETS BASED ON THERMOSETTING RESINS FOR ELECTRICAL PURPOSES - PART 2: METHODS OF TEST |
BS EN 62011-2:2004 | Insulating materials. Industrial, rigid, moulded, laminated tubes and rods of rectangular and hexagonal cross-section, based on thermosetting resins for electrical purposes Methods of test |
15/30302738 DC : 0 | BS ISO 19213 - IMPLANTS FOR SURGERY - TEST METHODS OF MATERIAL FOR USE AS A CORTICAL BONE MODEL |
13/30271610 DC : 0 | BS ISO 17296-3 - ADDITIVE MANUFACTURING - RAPID TECHNOLOGIES (RAPID PROTOTYPING) - PART 3: TEST METHODS |
I.S. EN ISO 17296-3:2016 | ADDITIVE MANUFACTURING - GENERAL PRINCIPLES - PART 3: MAIN CHARACTERISTICS AND CORRESPONDING TEST METHODS (ISO 17296-3:2014) |
API SPEC 17J : 2014 | SPECIFICATION FOR UNBONDED FLEXIBLE PIPE |
BS ISO 13628-11:2007 | Petroleum and natural gas industries. Design and operation of subsea production systems Flexible pipe systems for subsea and marine applications |
BS 3126:1987 | Method of specifying toughened polystyrene (SB) moulding and extrusion materials |
ISO 15814:1999 | Implants for surgery Copolymers and blends based on polylactide In vitro degradation testing |
ISO 17558:2006 | Steel wire ropes Socketing procedures Molten metal and resin socketing |
I.S. EN 50617-1:2015 | RAILWAY APPLICATIONS - TECHNICAL PARAMETERS OF TRAIN DETECTION SYSTEMS FOR THE INTEROPERABILITY OF THE TRANS-EUROPEAN RAILWAY SYSTEM - PART 1: TRACK CIRCUITS |
ISO/TR 15655:2003 | Fire resistance Tests for thermo-physical and mechanical properties of structural materials at elevated temperatures for fire engineering design |
API TR 17TR8 : 2018 | HIGH-PRESSURE HIGH-TEMPERATURE DESIGN GUIDELINES |
UNE-EN ISO 17296-3:2017 | Additive manufacturing - General principles - Part 3: Main characteristics and corresponding test methods (ISO 17296-3:2014) |
UNE-EN ISO 20753:2015 | Plastics - Test specimens (ISO 20753:2008) |
ASTM D 5592 : 1994 : R2002 : EDT 1 | Standard Guide for Material Properties Needed in Engineering Design Using Plastics |
EN ISO 13628-11:2008/AC:2009 | PETROLEUM AND NATURAL GAS INDUSTRIES - DESIGN AND OPERATION OF SUBSEA PRODUCTION SYSTEMS - PART 11: FLEXIBLE PIPE SYSTEMS FOR SUBSEA AND MARINE APPLICATIONS |
ISO 11248:1993 | Plastics — Thermosetting moulding materials — Evaluation of short-term performance at elevated temperatures |
BS EN 61212-2:2006 | Insulating materials. Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes Methods of test |
EN 61212-2:2006 | Insulating materials - Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes - Part 2: Methods of test |
CEN/TR 14548:2003 | Adhesives - Guide to test methods and other standards for the general requirements, characterization and safety of structural adhesives |
DIN EN 13411-4:2011-06 | Terminations for steel wire ropes - Safety - Part 4: Metal and resin socketing |
EN 13411-4:2011 | Terminations for steel wire ropes - Safety - Part 4: Metal and resin socketing |
EN 60455-2:2015 | Resin based reactive compounds used for electrical insulation - Part 2: Methods of test |
EN 50617-1:2015 | Railway applications - Technical parameters of train detection systems for the interoperability of the trans-European railway system - Part 1: Track circuits |
SAE ARP7204:2023 | Polymeric Bearings for Linear Actuators |
AAMITIR17:2017(R2023) | Compatibility of materials subject to sterilization |
BS 4935:1989 | Method of specifying acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials |
ISO 293:2004 | Plastics — Compression moulding of test specimens of thermoplastic materials |
ISO 3167:2014 | Plastics Multipurpose test specimens |
ISO 7616:1986 | Cellular plastics, rigid — Determination of compressive creep under specified load and temperature conditions |
EN ISO 10724-1 : 2001 | PLASTICS - INJECTION MOULDING OF TEST SPECIMENS OF THERMOSETTING POWDER MOULDING COMPOUNDS (PMCS) - PART 1: GENERAL PRINCIPLES AND MOULDING OF MULTIPURPOSE TEST SPECIMENS |
ISO 295:2004 | Plastics — Compression moulding of test specimens of thermosetting materials |
ISO 10724-1:1998 | Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 1: General principles and moulding of multipurpose test specimens |
EN ISO 2818:1996 | PLASTICS - PREPARATION OF TEST SPECIMENS BY MACHINING |
ISO 2602:1980 | Statistical interpretation of test results Estimation of the mean Confidence interval |
EN ISO 3167:2014 | Plastics - Multipurpose test specimens (ISO 3167:2014) |
ISO 472:2013 | Plastics Vocabulary |
EN ISO 295 : 2004 | PLASTICS - COMPRESSION MOULDING OF TEST SPECIMENS OF THERMOSETTING MATERIALS |
ISO 291:2008 | Plastics Standard atmospheres for conditioning and testing |
ISO 3597-3:2003 | Textile-glass-reinforced plastics Determination of mechanical properties on rods made of roving-reinforced resin Part 3: Determination of compressive strength |
EN ISO 291:2008 | Plastics - Standard atmospheres for conditioning and testing (ISO 291:2008) |
ISO 5893:2002 | Rubber and plastics test equipment Tensile, flexural and compression types (constant rate of traverse) Specification |
ISO 7743:2017 | Rubber, vulcanized or thermoplastic Determination of compression stress-strain properties |
ISO 294-1:2017 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens |
ISO 2818:1994 | Plastics — Preparation of test specimens by machining |
ISO 14126:1999 | Fibre-reinforced plastic composites — Determination of compressive properties in the in-plane direction |
EN ISO 294-1:2017 | Plastics - Injection moulding of test specimens of thermoplastic materials - Part 1: General principles, and moulding of multipurpose and bar test specimens (ISO 294-1:2017) |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.