API 616 REDLINE : 2011
Withdrawn
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
View Superseded by
GAS TURBINES FOR THE PETROLEUM, CHEMICAL, AND GAS INDUSTRY SERVICES
Withdrawn date
30-08-2024
Superseded by
Published date
01-01-2011
Publisher
Sorry this product is not available in your region.
1 Scope
2 References
3 Terms, Definitions, Acronyms, Abbreviations,
and Symbols
4 Basic Design
5 Accessories
6 Inspection, Testing, and Preparation for Shipment
7 Vendor's Data
Annex A (informative) - Typical Datasheets
Annex B (normative) - Gas Turbine Vendor Drawing and
Data Requirements (VDDR)
Annex C (normative) - Procedure for Determination of
Residual Unbalance
Annex D (normative) - Torsional and Lateral Flowcharts
Annex E (informative) - Gas Turbine Nomenclature
Describes the minimum requirements for open, simple, and regenerative-cycle combustion gas turbine units for services of mechanical drive, generator drive, or process gas generation.
| DocumentType |
Redline
|
| PublisherName |
American Petroleum Institute
|
| Status |
Withdrawn
|
| SupersededBy |
| ISO 10816-4:2009 | Mechanical vibration Evaluation of machine vibration by measurements on non-rotating parts Part 4: Gas turbine sets with fluid-film bearings |
| ISO 14691:2008 | Petroleum, petrochemical and natural gas industries — Flexible couplings for mechanical power transmission — General-purpose applications |
| NFPA 2001 : 2015 | CLEAN AGENT FIRE EXTINGUISHING SYSTEMS |
| NFPA 750 : 2015 | WATER MIST FIRE PROTECTION SYSTEMS |
| ISO 7005-2:1988 | Metallic flanges — Part 2: Cast iron flanges |
| ISO 3744:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane |
| ISO 7919-4:2009 | Mechanical vibration Evaluation of machine vibration by measurements on rotating shafts Part 4: Gas turbine sets with fluid-film bearings |
| ISO 6183:2009 | Fire protection equipment Carbon dioxide extinguishing systems for use on premises Design and installation |
| ASTM A 123/A123M : 2017 : REDLINE | Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products |
| ASME PV CODE 9 : 2017 | BOILER AND PRESSURE VESSEL CODE - WELDING, BRAZING, AND FUSING QUALIFICATIONS - QUALIFICATION STANDARD FOR WELDING, BRAZING, AND FUSING PROCEDURES; WELDERS; BRAZERS; AND WELDING, BRAZING, AND FUSING OPERATORS |
| API 546 : 2008 | BRUSHLESS SYNCHRONOUS MACHINES - 500 KVA AND LARGER |
| IEEE 841-2009 | IEEE Standard for Petroleum and Chemical Industry--Premium-Efficiency, Severe-Duty, Totally Enclosed Fan-Cooled (TEFC) Squirrel Cage Induction Motors--Up to and Including 370 kW (500 hp) |
| ASTM A 395/A395M : 1999 | Standard Specification for Ferritic Ductile Iron Pressure-Retaining Castings for Use at Elevated Temperatures |
| API 614 : 2008 | LUBRICATION, SHAFT-SEALING AND OIL-CONTROL SYSTEMS AND AUXILIARIES |
| IEC 60204-1:2016 | Safety of machinery - Electrical equipment of machines - Part 1: General requirements |
| ISO 7919-1:1996 | Mechanical vibration of non-reciprocating machines Measurements on rotating shafts and evaluation criteria Part 1: General guidelines |
| ASME B16.11 : 2016 | FORGED FITTINGS, SOCKET-WELDING AND THREADED |
| ASTM A 516/A516M : 2017 : REDLINE | Standard Specification for Pressure Vessel Plates, Carbon Steel, for Moderate- and Lower-Temperature Service |
| NEMA 250 : 2014 | ENCLOSURES FOR ELECTRICAL EQUIPMENT (1000 VOLTS MAXIMUM) |
| ASME B16.42 : 2016 | DUCTILE IRON PIPE FLANGES AND FLANGED FITTINGS - CLASSES 150 AND 300 |
| ASME B31.3:2016 | PROCESS PIPING |
| ISO 1940-1:2003 | Mechanical vibration Balance quality requirements for rotors in a constant (rigid) state Part 1: Specification and verification of balance tolerances |
| ISO 14123-1:2015 | Safety of machinery Reduction of risks to health resulting from hazardous substances emitted by machinery Part 1: Principles and specifications for machinery manufacturers |
| ISO 1461:2009 | Hot dip galvanized coatings on fabricated iron and steel articles — Specifications and test methods |
| ASME B46.1 : 2009 | SURFACE TEXTURE (SURFACE ROUGHNESS, WAVINESS, AND LAY) |
| EN 614-1:2006+A1:2009 | Safety of machinery - Ergonomic design principles - Part 1: Terminology and general principles |
| ASME PTC1 : 2015 | General Instructions (PTC 1 - 2015)<br> |
| ISO 6708:1995 | Pipework components Definition and selection of DN (nominal size) |
| ISO 281:2007 | Rolling bearings Dynamic load ratings and rating life |
| ASTM A 578/A578M : 2017 : REDLINE | Standard Specification for Straight-Beam Ultrasonic Examination of Rolled Steel Plates for Special Applications |
| EN 779:2012 | Particulate air filters for general ventilation - Determination of the filtration performance |
| ISO/TR 13387-7:1999 | Fire safety engineering Part 7: Detection, activation and suppression |
| ASME B16.1 : 2015 | Gray Iron Pipe Flanges and Flanged Fittings: Classes 25, 125, and 250 |
| ASME B1.20.1 : 2013(R2018) | PIPE THREADS, GENERAL PURPOSE (INCH) |
| API 670 : 2014 | MACHINERY PROTECTION SYSTEMS |
| ASTM A 563 : 2015 : REDLINE | Standard Specification for Carbon and Alloy Steel Nuts |
| ISO 8821:1989 | Mechanical vibration Balancing Shaft and fitment key convention |
| ISO 7-1:1994 | Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation |
| ISO 21789:2009 | Gas turbine applications — Safety |
| ISO 2314:2009 | Gas turbines — Acceptance tests |
| MIL-E-5007 Revision D:1973 | ENGINE, AIRCRAFT, TURBOJET AND TURBOFAN, GENERAL SPECIFICATION FOR |
| ISO 19499:2007 | Mechanical vibration Balancing Guidance on the use and application of balancing standards |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| ISO 10816-1:1995 | Mechanical vibration Evaluation of machine vibration by measurements on non-rotating parts Part 1: General guidelines |
| MIL-S-8879 Revision C:1991 | SCREW THREADS, CONTROLLED RADIUS ROOT WITH INCREASED MINOR DIAMETER, GENERAL SPECIFICATION FOR |
| NFPA 70 : 2017 | NATIONAL ELECTRICAL CODE |
| SAE J514_201201 | Hydraulic Tube Fittings |
| NFPA 12 : 2015 | CARBON DIOXIDE EXTINGUISHING SYSTEMS |
| IEC 60079-0:2011 | Explosive atmospheres - Part 0: Equipment - General requirements |
| SSPC-SP 6 : 2015 | COMMERCIAL BLAST CLEANING |
| IEC 60034-1:2017 | Rotating electrical machines - Part 1: Rating and performance |
| ASME PV CODE 7 : 2017 | BPVC Section VII-BOILER AND PRESSURE VESSEL CODE - RECOMMENDED GUIDELINES FOR THE CARE OF POWER BOILERS |
| API 612 : 2014 | PETROLEUM, PETROCHEMICAL, AND NATURAL GAS INDUSTRIES - STEAM TURBINES - SPECIAL-PURPOSE APPLICATIONS |
| ASME B16.5 : 2017 | PIPE FLANGES AND FLANGED FITTINGS: NPS 1/2 THROUGH NPS 24 METRIC/INCH STANDARD |
| ASME PV CODE 5 : 2017 | BOILER AND PRESSURE VESSEL CODE - NONDESTRUCTIVE EXAMINATION |
| ISO 261:1998 | ISO general purpose metric screw threads — General plan |
| API STD 541 : 2014 | FORM-WOUND SQUIRREL CAGE INDUCTION MOTORS - 375 KW (500 HORSEPOWER) AND LARGER |
| API 686 : 2009 | RECOMMENDED PRACTICE FOR MACHINERY INSTALLATION AND INSTALLATION DESIGN |
| ASME PV CODE 8 SET : 2013 | ASME BOILER AND PRESSURE VESSEL CODE (BPVC) - RULES FOR CONSTRUCTION OF PRESSURE VESSELS (SET) |
| ISO 7005-1:2011 | Pipe flanges — Part 1: Steel flanges for industrial and general service piping systems |
| ISO 10441:2007 | Petroleum, petrochemical and natural gas industries Flexible couplings for mechanical power transmission Special-purpose applications |
| ASTM E 709 : 2015 : REDLINE | Standard Guide for Magnetic Particle Testing |
| AWS D1.1/D1.1M : 2015 | STRUCTURAL WELDING CODE-STEEL |
| EN 288-9 : 1999 | SPECIFICATION AND APPROVAL OF WELDING PROCEDURES FOR METALLIC MATERIALS - WELDING PROCEDURE TEST FOR PIPELINE WELDING ON LAND AND OFFSHORE SITE BUTT WELDING OF TRANSMISSION PIPELINES |
| ASTM A 515/A515M : 2017 : REDLINE | Standard Specification for Pressure Vessel Plates, Carbon Steel, for Intermediate- and Higher-Temperature Service |
| ASME B16.47 : 2017 | LARGE DIAMETER STEEL FLANGES: NPS 26 THROUGH NPS 60 METRIC/INCH STANDARD |
| API 547 : 2017 | GENERAL PURPOSE FORM-WOUND SQUIRREL CAGE INDUCTION MOTORS - 185 KW (250 HP) THROUGH 2240 KW (3000 HP) |
| IEC 61779-1:1998 | Electrical apparatus for the detection and measurement of flammable gases - Part 1: General requirements and test methods |
| ISO 3448:1992 | Industrial liquid lubricants — ISO viscosity classification |
| ISO 10494:1993 | Gas turbines and gas turbine sets Measurement of emitted airborne noise Engineering/survey method |
| ASME PTC22 : 2014 | GAS TURBINES |
| ISO 8068:2006 | Lubricants, industrial oils and related products (class L) — Family T (Turbines) — Specification for lubricating oils for turbines |
| 1994/9/EC : 1994 | DIRECTIVE 94/9/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL OF 23 MARCH 1994 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES CONCERNING EQUIPMENT AND PROTECTIVE SYSTEMS INTENDED FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES |
| EN 287-1:2011 | Qualification test of welders - Fusion welding - Part 1: Steels |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.