IEC 61025:2006
|
Fault tree analysis (FTA) |
IEC 60695-11-20:2015
|
Fire hazard testing - Part 11-20: Test flames - 500 W flame test method |
IEC 61000-4-8 : 2.0
|
ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-8: TESTING AND MEASUREMENT TECHNIQUES - POWER FREQUENCY MAGNETIC FIELD IMMUNITY TEST |
IEC 60480:2004
|
Guidelines for the checking and treatment of sulfur hexafluoride (SF6) taken from electrical equipment and specification for its re-use |
IEC 60874-10:1992
|
Connectors for optical fibres and cables - Part 10: Sectional specification - Fibre optic connector type BFOC/2,5 |
IEC 61000-4-10 : 2.0
|
ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-10: TESTING AND MEASUREMENT TECHNIQUES - DAMPED OSCILLATORY MAGNETIC FIELD IMMUNITY TEST |
IEC 60255-22-1:2007
|
Measuring relays and protection equipment - Part 22-1: Electrical disturbance tests - 1 MHz burst immunity tests |
EN 50160 : 2010 AMD 1 2015
|
VOLTAGE CHARACTERISTICS OF ELECTRICITY SUPPLIED BY PUBLIC ELECTRICITY NETWORKS |
IEC 60038:2009
|
IEC standard voltages |
IEC 60270:2000+AMD1:2015 CSV
|
High-voltage test techniques - Partial discharge measurements |
CSA C71.2 : 1998
|
INSULATION COORDINATION - PART 2: APPLICATION GUIDE |
IEC 60044-7:1999
|
Instrument transformers - Part 7: Electronic voltage transformers |
IEC 60028:1925
|
International standard of resistance for copper |
IEC 61850-9-1:2003
|
Communication networks and systems in substations - Part 9-1: Specific Communication Service Mapping (SCSM) - Sampled values over serial unidirectional multidrop point to point link |
IEC 61000-4-4 : 3.0EN+(REDLINE+VERSION)
|
ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-4: TESTING AND MEASUREMENT TECHNIQUES - ELECTRICAL FAST TRANSIENT/BURST IMMUNITY TEST |
IEC 61000-4-1:2006
|
Electromagnetic compatibility (EMC) - Part 4-1: Testing and measurement techniques - Overview of IEC 61000-4 series |
IEC 62155:2003
|
Hollow pressurized and unpressurized ceramic and glass insulators for use in electrical equipment with rated voltages greater than 1 000 V |
IEC 60812:2006
|
Analysis techniques for system reliability - Procedure for failure mode and effects analysis (FMEA) |
IEC TS 61462:1998
|
Composite insulators - Hollow insulators for use in outdoor and indoor electrical equipment - Definitions, test methods, acceptance criteria and design recommendations |
ASTM D 4364 : 2013 : REDLINE
|
Standard Practice for Performing Outdoor Accelerated Weathering Tests of Plastics Using Concentrated Sunlight |
IEC 60050-601:1985
|
International Electrotechnical Vocabulary (IEV) - Part 601: Generation, transmission and distribution of electricity - General |
IEC 60304:1982
|
Standard colours for insulation for low-frequency cables and wires |
IEC 61000-4-11:2004+AMD1:2017 CSV
|
Electromagnetic compatibility (EMC) - Part 4-11: Testing and measurement techniques - Voltage dips, short interruptions and voltage variations immunity tests |
IEC 60255-24:2013
|
Measuring relays and protection equipment - Part 24: Common format for transient data exchange (COMTRADE) for power systems |
IEC 60599:2015
|
Mineral oil-filled electrical equipment in service - Guidance on the interpretation of dissolved and free gases analysis |
IEC 61000-4-12 : 3.0
|
ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-12: TESTING AND MEASUREMENT TECHNIQUES - RING WAVE IMMUNITY TEST |
IEC 61508-3:2010
|
Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 3: Software requirements (see Functional Safety and IEC 61508) |
IEC 60056:1987
|
High-voltage alternating-current circuit-breakers |
IEC 60376:2005
|
Specification of technical grade sulfur hexafluoride (SF6) for use in electrical equipment |
IEC 60567:2011
|
Oil-filled electrical equipment - Sampling of gases and analysis of free and dissolved gases - Guidance |
IEC 61166:1993
|
High-voltage alternating current circuit-breakers - Guide for seismic qualification of high-voltage alternating current circuit-breakers |
IEC 60694:1996+AMD1:2000+AMD2:2001 CSV
|
Common specifications for high-voltage switchgear and controlgear standards |
IEC 60085:2007
|
Electrical insulation - Thermal evaluation and designation |
IEC 60296:2012 RLV
|
Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear |
IEC 60721-2-2:2012
|
Classification of environmental conditions - Part 2-2: Environmental conditions appearing in nature - Precipitation and wind |
IEC 61000-4-9 : 2.0
|
ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-9: TESTING AND MEASUREMENT TECHNIQUES - IMPULSE MAGNETIC FIELD IMMUNITY TEST |
ASTM G 154 : 2016 : REDLINE
|
Standard Practice for Operating Fluorescent Ultraviolet (UV) Lamp Apparatus for Exposure of Nonmetallic Materials |
ASTM D 2303 : 2013
|
Standard Test Methods for Liquid-Contaminant, Inclined-Plane Tracking and Erosion of Insulating Materials |
IEC 60707:1999
|
Flammability of solid non-metallic materials when exposed to flame sources - List of test methods |
IEC 60044-6:1992
|
Instrument transformers - Part 6: Requirements for protective current transformers for transient performance |
IEC 60437:1997
|
Radio interference test on high-voltage insulators |
IEC 60121:1960
|
Recommendation for commercial annealed aluminium electrical conductor wire |
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV
|
Degrees of protection provided by enclosures (IP Code) |
IEC 60044-1:1996+AMD1:2000+AMD2:2002 CSV
|
Instrument transformers - Part 1: Current transformers |
IEC 61850-9-2:2011
|
Communication networks and systems for power utility automation - Part 9-2: Specific communication service mapping (SCSM) - Sampled values over ISO/IEC 8802-3 |
IEC 60068-2-17:1994
|
Basic environmental testing procedures - Part 2-17: Tests - Test Q: Sealing |
IEC 61000-4-2:2008
|
Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity test |
IEC 60695-11-10:2013
|
Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods |
IEC 61000-4-3:2006+AMD1:2007+AMD2:2010 CSV
|
Electromagnetic compatibility (EMC) - Part 4-3: Testing and measurement techniques - Radiated, radio-frequency, electromagnetic field immunity test |
IEC 60376B:1974
|
Second supplement: Clause 26 |
IEC 60255-5:2000
|
Electrical Relays - Part 5: Insulation coordination for measuring relays and protection equipment - Requirements and tests |
IEC 61850-7-4:2010
|
Communication networks and systems for power utility automation - Part 7-4: Basic communication structure - Compatible logical node classes and data object classes |
IEC 60050-321:1986
|
International Electrotechnical Vocabulary (IEV) - Part 321: Instrument transformers |
IEC 60071-2:1996
|
Insulation co-ordination - Part 2: Application guide |
IEC TS 60695-11-3:2004
|
Fire hazard testing - Part 11-3: Test flames - 500 W flames - Apparatus and confirmational test methods |
IEC 61000-4-7:2002+AMD1:2008 CSV
|
Electromagnetic compatibility (EMC) - Part 4-7: Testing and measurement techniques - General guide on harmonics and interharmonics measurements and instrumentation, for power supply systems and equipment connected thereto |
IEC 60721-3-3:1994+AMD1:1995+AMD2:1996 CSV
|
Classification of environmental conditions - Part 3-3: Classification of groups of environmental parameters and their severities - Stationary use at weatherprotected locations |
IEC 60068-2-75:2014
|
Environmental testing - Part 2-75: Tests - Test Eh: Hammer tests |
CISPR 11:2015 RLV
|
Industrial, scientific and medical equipment - Radio-frequency disturbance characteristics - Limits and methods of measurement |
IEC 60721-2-4:1987+AMD1:1988 CSV
|
Classification of environmental conditions - Part 2-4: Environmental conditions appearing in nature - Solar radiation and temperature |
TIA 485 : A1998(R2012)
|
ELECTRICAL CHARACTERISTICS OF GENERATORS AND RECEIVERS FOR USE IN BALANCED DIGITAL MULTIPOINT SYSTEMS |
IEC 60870-5-1:1990
|
Telecontrol equipment and systems. Part 5: Transmission protocols - Section One: Transmission frame formats |
IEC 60587:2007
|
Electrical insulating materials used under severe ambient conditions - Test methods for evaluating resistance to tracking and erosion |
IEC 61508-1:2010
|
Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 1: General requirements (see Functional Safety and IEC 61508) |
IEC 60060-1:2010
|
High-voltage test techniques - Part 1: General definitions and test requirements |
IEC 61754-15:2009
|
Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 15: Type LSH connector family |
IEC 60071-1:2006+AMD1:2010 CSV
|
Insulation co-ordination - Part 1: Definitions, principles and rules |
IEC TS 60695-11-4:2004
|
Fire hazard testing - Part 11-4: Test flames - 50 W flame - Apparatus and confirmational test method |
IEC 61000-4-29:2000
|
Electromagnetic compatibility (EMC) - Part 4-29: Testing and measurement techniques - Voltage dips, short interruptions and voltage variations on d.c. input power port immunity tests |
IEC 61754-1:2013
|
Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 1: General and guidance |
IEC 60664-1:2007
|
Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests |
CSA C71.1 : 1999
|
INSULATION CO-ORDINATION - PART 1: DEFINITIONS, PRINCIPLES AND RULES |
IEC 61000-4-13:2002+AMD1:2009+AMD2:2015 CSV
|
Electromagnetic compatibility (EMC) - Part 4-13: Testing and measurement techniques - Harmonics and interharmonics includingmains signalling at a.c. power port, low frequency immunity tests |
IEEE 693-2005
|
SEISMIC DESIGN OF SUBSTATIONS |
IEC 61850-3:2013
|
Communication networks and systems for power utility automation - Part 3: General requirements |
IEEE C57.135 : 2011
|
GUIDE FOR THE APPLICATION, SPECIFICATION, AND TESTING OF PHASE-SHIFTING TRANSFORMERS |