EN 545:2010
Current
Current
The latest, up-to-date edition.
Ductile iron pipes, fittings, accessories and their joints for water pipelines - Requirements and test methods
Published date
22-09-2010
Publisher
Sorry this product is not available in your region.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Technical requirements
5 Performance requirements for joints and pipe saddles
6 Test methods
7 Performance test methods
8 Tables of dimensions
9 Evaluation of conformity
Annex A (normative) Allowable pressures
Annex B (informative) Longitudinal bending resistance of pipes
Annex C (informative) Diametral stiffness of pipes
Annex D (informative) Specific coatings, field of use,
characteristics of soils
Annex E (informative) Field of use, water characteristics
Annex F (informative) Calculation method of buried pipelines,
heights of cover
Bibliography
This European Standard specifies the requirements and associated test methods applicable to ductile iron pipes, fittings, accessories and their joints for the construction of pipelines outside buildings:-to convey different types of water (e.g. raw water, treated water, re-used water) for all types of applications (e.g. water intended for human consumption, for fire protection, for snow making, for irrigation, for hydro-electricity etc.);-with or without pressure;-to be installed below or above ground.This European Standard is applicable to pipes, fittings and accessories which are: -manufactured with socketed, flanged or spigot ends;-supplied externally and internally coated;- suitable for fluid temperatures between 0 °C and 50 °C, excluding frost;-not intended for use in areas subject to fire regulations.NOTE 1This does not preclude special arrangements for the products to be used at higher temperatures.This European Standard covers pipes and fittings cast by any type of foundry process or manufactured by fabrication of cast components, as well as corresponding joints and accessories, in a size range extending from DN 40 to DN 2 000, inclusive.This European Standard specifies requirements for materials, dimensions and tolerances, mechanical properties and standard coatings of ductile iron pipes and fittings. It also gives performance requirements for all components including joints. Joint design and gasket shapes are outside the scope of this standard.In addition, reference is made to the performance requirements of couplings, flange adaptors and saddles manufactured for use with ductile iron pipes and fittings.NOTE 2In this European Standard, all pressures are relative pressures, expressed in bars (100 kPa = 1 bar).
| Committee |
CEN/TC 203
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| UNI EN 545 : 2010 | Identical |
| UNE-EN 545:2011 | Identical |
| BS EN 545:2010 | Identical |
| I.S. EN 545:2010 | Identical |
| NS EN 545 : 1ED 2010 | Identical |
| NBN EN 1559-3 : 2011 | Identical |
| SN EN 545 : 2010 | Identical |
| NEN EN 545 : 2010 | Identical |
| NBN EN 545 : 2010 | Identical |
| PN EN 545 : 2010 | Identical |
| NF EN 545 : 2010 | Identical |
| DIN EN 545:2011-09 | Identical |
| DIN 28602:2000-05 | DUCTILE IRON PIPES AND FITTINGS - BOLTED GLAND JOINTS - ASSEMBLY, SOCKETS, COUNTER RING, SEALING RING, BOLTS AND NUTS |
| 01/711715 DC : DRAFT AUG 2001 | BS EN 12502-5 - PROTECTION OF METALLIC MATERIALS AGAINST CORROSION - CORROSION LIKELIHOOD IN WATER CONVEYING SYSTEMS - PART 5 - REVIEW OF INFLUENCING FACTORS FOR CAST IRON, UNALLOYED AND LOW ALLOYED STEELS |
| UNI CEN/TR 16017 : 2010 | GUIDE TO THE USE OF EN 598 |
| PREN 1171 : DRAFT 2014 | INDUSTRIAL VALVES - CAST IRON GATE VALVES |
| PREN 598 : DRAFT 2017 | COATED AND LINED DUCTILE IRON PIPES, FITTINGS AND THEIR JOINTS FOR SEWERAGE AND DRAINAGE APPLICATIONS - PRODUCTS CHARACTERISTICS AND TEST AND ASSESSMENT METHODS |
| UNE-EN 1563:2012 | Founding - Spheroidal graphite cast irons |
| 03/104248 DC : DRAFT FEB 2003 | EN 14628 - DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EXTERNAL POLYETHYLENE COATING FOR PIPES IN HIGHLY AGGRESSIVE SOILS - REQUIREMENTS AND TEST METHODS |
| 05/30134037 DC : 0 | EN 12516-4 - INDUSTRIAL VALVES - SHELL DESIGN STRENGTH - PART 4: CALCULATION METHOD FOR VALVE SHELLS MANUFACTURED IN METALLIC MATERIALS OTHER THAN STEEL |
| BS EN 593:2017 | Industrial valves. Metallic butterfly valves for general purposes |
| 14/30294800 DC : 0 | BS EN 14901 - DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EPOXY COATING (HEAVY DUTY) OF DUCTILE IRON FITTINGS AND ACCESSORIES - REQUIREMENTS AND TEST METHODS |
| PD CEN/TR 16950:2016 | Ductile iron pipes, fittings and accessories. Sanitary characteristics and test methods |
| UNI EN 12516-4 : 2014 | INDUSTRIAL VALVES - SHELL DESIGN STRENGTH - PART 4: CALCULATION METHOD FOR VALVE SHELLS MANUFACTURED IN METALLIC MATERIALS OTHER THAN STEEL |
| 06/30153191 DC : 0 | BS EN 15542 - DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EXTERNAL CEMENT MORTAR COATING FOR PIPES - REQUIREMENTS AND TEST METHODS |
| DIN EN 15655:2016-07 (Draft) | DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - INTERNAL POLYURETHANE LINING FOR PIPES AND FITTINGS - REQUIREMENTS AND TEST METHODS |
| CEN/TR 16017:2010 | Guide to the use of EN 598 |
| I.S. EN 1563:2011 | FOUNDING - SPHEROIDAL GRAPHITE CAST IRONS |
| 15/30322070 DC : 0 | BS EN 1563 - FOUNDING - SPHEROIDAL GRAPHITE CAST IRONS |
| S.R. CEN/TR 16470:2013 | ENVIRONMENTAL ASPECTS OF DUCTILE IRON PIPE SYSTEMS FOR WATER AND SEWERAGE APPLICATIONS |
| UNI CEN/TR 15545 : 2007 | GUIDE TO THE USE OF EN 545 |
| BS EN 14525:2004 | Ductile iron wide tolerance couplings and flange adaptors for use with pipes of different materials: ductile iron, grey iron, steel, PVC-U, PE, fibre-cement |
| BS EN 14901:2006 | Ductile iron pipes, fittings and accessories. Epoxy coating (heavy duty) of ductile iron fittings and accessories. Requirements and test methods |
| BS EN 14628:2005 | Ductile iron pipes, fittings and accessories. External polythene coating for pipes. Requirements and test methods |
| I.S. EN 14901:2014 | DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EPOXY COATING (HEAVY DUTY) OF DUCTILE IRON FITTINGS AND ACCESSORIES - REQUIREMENTS AND TEST METHODS |
| CEN/TR 1295-2:2005 | Structural design of buried pipelines under various conditions of loading - Part 2: Summary of nationally established methods of design |
| EN 1092-2:1997 | Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 2: Cast iron flanges |
| DIN EN 12502-5:2005-03 | PROTECTION OF METALLIC MATERIALS AGAINST CORROSION - GUIDANCE ON THE ASSESSMENT OF CORROSION LIKELIHOOD IN WATER DISTRIBUTION AND STORAGE SYSTEMS - PART 5: INFLUENCING FACTORS FOR CAST IRON, UNALLOYED AND LOW-ALLOY STEELS |
| DIN EN 15189:2007-02 | Ductile iron pipes, fittings and accessories - External polyurethane coating for pipes - Requirements and test methods |
| ÖNORM EN 14525:2023 01 01 | Ductile iron and steel wide tolerance couplings and flange adaptors for use with pipes of different materials: ductile iron, Grey iron, steel, PVC-U, PVC-O, PE, fibre-cement |
| DIN 28601:2000-06 | DUCTILE IRON PIPES AND FITTINGS - SCREWED SOCKET JOINTS - ASSEMBLY, SOCKETS, SCREW RINGS, SEALING RINGS AND SLIP RINGS |
| 05/30131069 DC : DRAFT MAR 2005 | EN 598:2005 - DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR SEWERAGE APPLICATIONS - REQUIREMENTS AND TEST METHODS |
| PD CEN/TR 15545:2006 | Guide to the use of EN 545 |
| 16/30339483 DC : 0 | BS EN 593 - INDUSTRIAL VALVES - METALLIC BUTTERFLY VALVES FOR GENERAL PURPOSES |
| DIN 28650:1999-11 | DUCTILE IRON FITTINGS - DOUBLE SOCKET 30 DEGREE BENDS, EN-FITTINGS, MI-FITTINGS, IT-FITTINGS - APPLICATION, DIMENSIONS |
| 10/30216654 DC : 0 | BS EN 12842 - DUCTILE IRON FITTINGS FOR PVC-U OR PE PIPING SYSTEMS - REQUIREMENTS AND TEST METHODS |
| UNI EN 15655 : 2009 | DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - INTERNAL POLYURETHANE LINING FOR PIPES AND FITTINGS - REQUIREMENTS AND TEST METHODS |
| UNI EN 15542 : 2008 | DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EXTERNAL CEMENT MORTAR COATING FOR PIPES - REQUIREMENTS AND TEST METHODS |
| 11/30249111 DC : 0 | BS EN 12516-4 - INDUSTRIAL VALVES - SHELL DESIGN STRENGTH - PART 4: CALCULATION METHOD FOR VALVE SHELLS MANUFACTURED IN METALLIC MATERIALS OTHER THAN STEEL |
| 04/30121907 DC : DRAFT SEP 2004 | PREN 14901 - DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EPOXY COATING OF DUCTILE IRON FITTINGS AND ACCESSORIES (HEAVY DUTY) - REQUIREMENTS AND TEST METHODS |
| 05/30131064 DC : DRAFT MAR 2005 | EN 15189:2005 - DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EXTERNAL POLYURETHANE COATING FOR PIPES - REQUIREMENTS AND TEST METHODS |
| 16/30340626 DC : 0 | BS EN 15655 - DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - INTERNAL POLYURETHANE LINING FOR PIPES AND FITTINGS - REQUIREMENTS AND TEST METHODS |
| I.S. EN 593:2017 | INDUSTRIAL VALVES - METALLIC BUTTERFLY VALVES FOR GENERAL PURPOSES |
| CEN/TR 16470:2013 | Environmental aspects of ductile iron pipe systems for water and sewerage applications |
| UNE-EN 16668:2016 | Industrial valves - Requirements and testing for metallic valves as pressure accessories |
| EN 12516-4:2014 | Industrial valves - Shell design strength - Part 4: Calculation method for valve shells manufactured in metallic materials other than steel |
| UNI EN 1563 : 2012 | FOUNDING - SPHEROIDAL GRAPHITE CAST IRONS |
| EN 1563:2011 | Founding - Spheroidal graphite cast irons |
| DIN EN 12516-4:2015-01 | INDUSTRIAL VALVES - SHELL DESIGN STRENGTH - PART 4: CALCULATION METHOD FOR VALVE SHELLS MANUFACTURED IN METALLIC MATERIALS OTHER THAN STEEL |
| DIN EN 1171:2015-11 | INDUSTRIAL VALVES - CAST IRON GATE VALVES |
| DIN EN 12842:2012-11 | Ductile iron fittings for PVC-U or PE piping systems - Requirements and test methods |
| DIN EN 598:2009-10 | Ductile iron pipes, fittings, accessories and their joints for sewerage applications - Requirements and test methods (includes Amendment A1:2009) |
| BS EN 598 : 2007 | DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR SEWERAGE APPLICATIONS - REQUIREMENTS AND TEST METHODS |
| DIN EN 14901:2014-12 | DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EPOXY COATING (HEAVY DUTY) OF DUCTILE IRON FITTINGS AND ACCESSORIES - REQUIREMENTS AND TEST METHODS |
| I.S. EN 1171:2015 | INDUSTRIAL VALVES - CAST IRON GATE VALVES |
| I.S. EN 598:2007 | DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR SEWERAGE APPLICATIONS - REQUIREMENTS AND TEST METHODS |
| I.S. EN 12842:2012 | DUCTILE IRON FITTINGS FOR PVC-U OR PE PIPING SYSTEMS - REQUIREMENTS AND TEST METHODS |
| I.S. EN 969:2009 | DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR GAS PIPELINES - REQUIREMENTS AND TEST METHODS |
| I.S. EN 14628:2005 | DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EXTERNAL POLYETHYLENE COATING FOR PIPES - REQUIREMENTS AND TEST METHODS |
| I.S. EN 1092-2:1997 | FLANGES AND THEIR JOINTS - CIRCULAR FLANGES FOR PIPES, VALVES, FITTINGS AND ACCESSORIES, PN DESIGNATED - PART 2: CAST IRON FLANGES |
| DIN EN 1563:2015-07 (Draft) | FOUNDING - SPHEROIDAL GRAPHITE CAST IRONS |
| PREN 12842 : DRAFT 2010 | DUCTILE IRON FITTINGS FOR PVC-U OR PE PIPING SYSTEMS - REQUIREMENTS AND TEST METHODS |
| DIN 30674-3:2001-03 | SHEATHING DUCTILE CAST IRON PIPES - PART 3: ZINC COATING WITH PROTECTIVE SHEATHING |
| 02/710115 DC : DRAFT AUG 2002 | PREN 14525 - DUCTILE IRON WIDE TOLERANCE COUPLINGS AND FLANGE ADAPTORS FOR USE WITH PIPES OF DIFFERENT MATERIALS: DUCTILE IRON, GREY IRON, STEEL, PVC-U PE, FIBRE-CEMENT |
| PREN 12516-4 : DRAFT 2011 | INDUSTRIAL VALVES - SHELL DESIGN STRENGTH - PART 4: CALCULATION METHOD FOR VALVE SHELLS MANUFACTURED IN METALLIC MATERIALS OTHER THAN STEEL |
| 07/19990369 DC : 0 | BS EN 806-4 - SPECIFICATIONS FOR INSTALLATIONS INSIDE BUILDINGS CONVEYING WATER FOR HUMAN CONSUMPTION - PART 4 - INSTALLATION |
| UNI EN 806-4 : 2010 | SPECIFICATIONS FOR INSTALLATIONS INSIDE BUILDINGS CONVEYING WATER FOR HUMAN CONSUMPTION - PART 4: INSTALLATION |
| BS EN 806-4:2010 | Specifications for installations inside buildings conveying water for human consumption Installation |
| S.R. CEN/TR 16950:2016 | DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - SANITARY CHARACTERISTICS AND TEST METHODS |
| PREN 15655 : DRAFT 2016 | DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - INTERNAL POLYURETHANE LINING FOR PIPES AND FITTINGS - REQUIREMENTS AND TEST METHODS |
| NF EN 806-4 : 2010 | SPECIFICATIONS FOR INSTALLATIONS INSIDE BUILDINGS CONVEYING WATER FOR HUMAN CONSUMPTION - PART 4: INSTALLATION |
| BS EN 16668 : 2016 | INDUSTRIAL VALVES - REQUIREMENTS AND TESTING FOR METALLIC VALVES AS PRESSURE ACCESSORIES |
| I.S. EN 15655:2009 | DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - INTERNAL POLYURETHANE LINING FOR PIPES AND FITTINGS - REQUIREMENTS AND TEST METHODS |
| BS EN 969:2009 | Ductile iron pipes, fittings, accessories and their joints for gas pipelines. Requirements and test methods |
| UNE-EN 12842:2013 | Ductile iron fittings for PVC-U or PE piping systems - Requirements and test methods |
| UNI EN 14525 : 2005 | DUCTILE IRON WIDE TOLERANCE COUPLINGS AND FLANGE ADAPTORS FOR USE WITH PIPES OF DIFFERENT MATERIALS: DUCTILE IRON, GREY IRON, STEEL, PVC-U PE, FIBRE-CEMENT |
| UNI EN 15189 : 2007 | DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EXTERNAL POLYURETHANE COATING FOR PIPES - REQUIREMENTS AND TEST METHODS |
| UNI EN 969 : 2009 | DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR GAS PIPELINES - REQUIREMENTS AND TEST METHODS |
| UNI EN 12842 : 2012 | DUCTILE IRON FITTINGS FOR PVC-U OR PE PIPING SYSTEMS - REQUIREMENTS AND TEST METHODS |
| I.S. EN 14525:2005 | DUCTILE IRON WIDE TOLERANCE COUPLINGS AND FLANGE ADAPTORS FOR USE WITH PIPES OF DIFFERENT MATERIALS: DUCTILE IRON, GREY IRON, STEEL, PVC-U PE, FIBRE-CEMENT |
| UNI EN 14901 : 2014 | DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EPOXY COATING (HEAVY DUTY) OF DUCTILE IRON FITTINGS AND ACCESSORIES - REQUIREMENTS AND TEST METHODS |
| BS EN 1171:2015 | Industrial valves. Cast iron gate valves |
| UNI EN 598 : 2009 | DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR SEWERAGE APPLICATIONS - REQUIREMENTS AND TEST METHODS |
| CEN/TR 16950:2016 | Ductile iron pipes, fittings and accessories - Sanitary characteristics and test methods |
| DIN EN 15542:2008-06 | Ductile iron pipes, fittings and accessories - External cement mortar coating for pipes - Requirements and test methods |
| 14/30282872 DC : 0 | BS EN 1171 - INDUSTRIAL VALVES - CAST IRON GATE VALVES |
| 13/30287824 DC : 0 | BS EN 16668 - INDUSTRIAL VALVES - REQUIREMENTS AND TESTING FOR METALLIC VALVES AS PRESSURE ACCESSORIES |
| 00/708210 DC : DRAFT MAY 2000 | ISO/DIS 1071 - WELDING CONSUMABLES - WELDING CONSUMABLES FOR FUSION WELDING OF CAST IRON - CLASSIFICATION |
| I.S. EN 12516-4:2014 | INDUSTRIAL VALVES - SHELL DESIGN STRENGTH - PART 4: CALCULATION METHOD FOR VALVE SHELLS MANUFACTURED IN METALLIC MATERIALS OTHER THAN STEEL |
| PREN 593 : DRAFT 2016 | INDUSTRIAL VALVES - METALLIC BUTTERFLY VALVES FOR GENERAL PURPOSES |
| DIN EN 806-4:2010-06 | Specifications for installations inside buildings conveying water for human consumption - Part 4: Installation |
| 07/30156488 DC : 0 | EN 15655 - DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - INTERNAL POLYURETHANE LINING FOR PIPES AND FITTINGS - REQUIREMENTS AND TEST METHODS |
| BS EN 15655:2009 | Ductile iron pipes, fittings and accessories. Internal polyurethane lining for pipes and fittings. Requirements and test methods |
| BS EN 15542:2008 | Ductile iron pipes, fittings and accessories. External cement mortar coating for pipes. Requirements and test methods |
| DIN 28603:2002-05 | DUCTILE IRON PIPES AND FITTINGS - PUSH-IN JOINTS - SURVEY, SOCKETS AND GASKETS |
| UNE-EN 12516-4:2016 | Industrial valves - Shell design strength - Part 4: Calculation method for valve shells manufactured in metallic materials other than steel |
| PREN 14901 : DRAFT 2014 | DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EPOXY COATING (HEAVY DUTY) OF DUCTILE IRON FITTINGS AND ACCESSORIES - REQUIREMENTS AND TEST METHODS |
| I.S. EN 806-4:2010 | SPECIFICATIONS FOR INSTALLATIONS INSIDE BUILDINGS CONVEYING WATER FOR HUMAN CONSUMPTION - PART 4: INSTALLATION |
| I.S. EN 15542:2008 | DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EXTERNAL CEMENT MORTAR COATING FOR PIPES - REQUIREMENTS AND TEST METHODS |
| DIN EN 969:2009-07 | DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR GAS PIPELINES - REQUIREMENTS AND TEST METHODS |
| PD CEN/TR 1295-2:2005 | Structural design of buried pipelines under various conditions of loading Summary of nationally established methods of design |
| UNE-EN 14901:2015 | Ductile iron pipes, fittings and accessories - Epoxy coating (heavy duty) of ductile iron fittings and accessories - Requirements and test methods |
| BS EN 1503-3:2000 | Valves. Materials for bodies, bonnets and covers Cast irons specified in European Standards |
| BS EN 13397:2002 | Industrial valves. Diaphragm valves made of metallic materials |
| BS EN 15189:2006 | Ductile iron pipes, fittings and accessories. External polyurethane coating for pipes. Requirements and test methods |
| BS EN 806-2:2005 | Specifications for installations inside buildings conveying water for human consumption Design |
| BS EN 12056-2:2000 | Gravity drainage systems inside buildings Sanitary pipework, layout and calculation |
| BS EN 12502-5:2004 | Protection of metallic materials against corrosion. Guidance on the assessment of corrosion likelihood in water distribution and storage systems Influencing factors for cast iron, unalloyed and low alloyed steels |
| EN 14628:2005 | Ductile iron pipes, fittings and accessories - External polyethylene coating for pipes - Requirements and test methods |
| EN 15189:2006 | Ductile iron pipes, fittings and accessories - External polyurethane coating for pipes - Requirements and test methods |
| EN 1514-1:1997 | Flanges and their joints - Dimensions of gaskets for PN-designated flanges - Part 1: Non-metallic flat gaskets with or without inserts |
| EN 806-2:2005 | Specification for installations inside buildings conveying water for human consumption - Part 2: Design |
| EN 969:2009 | Ductile iron pipes, fittings, accessories and their joints for gas pipelines - Requirements and test methods |
| EN 14525:2004 | Ductile iron wide tolerance couplings and flange adaptors for use with pipes of different materials: ductile iron, Grey iron, Steel, PVC-U PE, Fibre-cement |
| EN 806-4:2010 | Specifications for installations inside buildings conveying water for human consumption - Part 4: Installation |
| EN 12502-5:2004 | Protection of metallic materials against corrosion - Guidance on the assessment of corrosion likelihood in water distribution and storage systems - Part 5: Influencing factors for cast iron, unalloyed and low alloyed steels |
| EN 12842:2012 | Ductile iron fittings for PVC-U or PE piping systems - Requirements and test methods |
| EN 598:2007+A1:2009 | Ductile iron pipes, fittings, accessories and their joints for sewerage applications - Requirements and test methods |
| EN 15542:2008 | Ductile iron pipes, fittings and accessories - External cement mortar coating for pipes - Requirements and test methods |
| EN 593:2017 | Industrial valves - Metallic butterfly valves for general purposes |
| EN 14901:2014 | Ductile iron pipes, fittings and accessories - Epoxy coating (heavy duty) of ductile iron fittings and accessories - Requirements and test methods |
| I.S. CEN TR 15545:2006 | GUIDE TO THE USE OF EN 545 |
| PD CEN/TR 16017:2010 | Guide to the use of EN 598 |
| PREN 1563 : DRAFT 2015 | FOUNDING - SPHEROIDAL GRAPHITE CAST IRONS |
| PD CEN/TR 16470:2013 | Environmental aspects of ductile iron pipe systems for water and sewerage applications |
| DIN 14244:2003-07 | Water suction connection for fire fighting - Under and above ground |
| BS EN 1563:2011 | Founding. Spheroidal graphite cast irons |
| UNI EN 806-2 : 2008 | SPECIFICATION FOR INSTALLATIONS INSIDE BUILDINGS CONVEYING WATER FOR HUMAN CONSUMPTION - PART 2: DESIGN |
| BS EN 12516-4 : 2014 | INDUSTRIAL VALVES - SHELL DESIGN STRENGTH - PART 4: CALCULATION METHOD FOR VALVE SHELLS MANUFACTURED IN METALLIC MATERIALS OTHER THAN STEEL |
| S.R. CEN TR 16017:2010 | GUIDE TO THE USE OF EN 598 |
| 17/30362692 DC : 0 | BS EN 598 - COATED AND LINED DUCTILE IRON PIPES, FITTINGS AND THEIR JOINTS FOR SEWERAGE AND DRAINAGE APPLICATIONS - PRODUCTS CHARACTERISTICS AND TEST AND ASSESSMENT METHODS |
| CEN/TR 15545:2006 | Guide to the use of EN 545 |
| EN 15655:2009 | Ductile iron pipes, fittings and accessories - Internal polyurethane lining for pipes and fittings - Requirements and test methods |
| DIN EN 1514-1:1997-08 | Flanges and their joints - Dimensions of gaskets for PN-designated flanges - Part 1: Non-metallic flat gaskets with or without inserts |
| DIN EN 13397:2002-03 | INDUSTRIAL VALVES - DIAPHRAGM VALVES MADE OF METALLIC MATERIALS |
| DIN EN 806-2:2005-06 | Specification for installations inside buildings conveying water for human consumption - Part 2: Design |
| UNE-EN 1171:2016 | Industrial valves - Cast iron gate valves |
| BS EN 12842:2012 | Ductile iron fittings for PVC-U or PE piping systems. Requirements and test methods |
| EN 13397:2001 | Industrial valves - Diaphragm valves made of metallic materials |
| EN 1171:2015 | Industrial valves - Cast iron gate valves |
| DIN EN 14525:2005-02 | Ductile iron wide tolerance couplings and flange adaptors for use with pipes of different materials: Ductile iron, grey iron, steel, PVC-U, PE, fibre-cement |
| DIN EN 14628:2006-01 | DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EXTERNAL POLYETHYLENE COATING FOR PIPES - REQUIREMENTS AND TEST METHODS |
| EN 15189:2006 | Ductile iron pipes, fittings and accessories - External polyurethane coating for pipes - Requirements and test methods |
| EN ISO 6506-1:2014 | Metallic materials - Brinell hardness test - Part 1: Test method (ISO 6506-1:2014) |
| ISO 6506-1:2014 | Metallic materials Brinell hardness test Part 1: Test method |
| ISO/IEC Guide 62:1996 | General requirements for bodies operating assessment and certification/registration of quality systems |
| EN ISO 7091:2000 | Plain washers - Normal series - Product grade C (ISO 7091:2000) |
| EN 197-1:2011 | Cement - Part 1: Composition, specifications and conformity criteria for common cements |
| EN 14525:2004 | Ductile iron wide tolerance couplings and flange adaptors for use with pipes of different materials: ductile iron, Grey iron, Steel, PVC-U PE, Fibre-cement |
| EN ISO 6892-1:2016 | Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1:2016) |
| ISO 4016:2011 | Hexagon head bolts Product grade C |
| ISO 4034:2012 | Hexagon regular nuts (style 1) Product grade C |
| 89/106/EEC : 1988 | COUNCIL DIRECTIVE OF 21 DECEMBER 1988 ON THE APPROXIMATION OF LAWS, REGULATIONS AND ADMINISTRATIVE PROVISIONS OF THE MEMBER STATES RELATING TO CONSTRUCTION PRODUCTS |
| EN 805:2000 | Water supply - Requirements for systems and components outside buildings |
| EN 45011:1998 | General requirements for bodies operating product certification systems (ISO/IEC Guide 65:1996) |
| ISO 6892-1:2016 | Metallic materials Tensile testing Part 1: Method of test at room temperature |
| EN ISO 4016:2011 | Hexagon head bolts - Product grade C (ISO 4016:2011) |
| ISO 6708:1995 | Pipework components Definition and selection of DN (nominal size) |
| EN 45011 : 1998 | GENERAL REQUIREMENTS FOR BODIES OPERATING PRODUCT CERTIFICATION SYSTEMS |
| EN 196-1:2016 | Methods of testing cement - Part 1: Determination of strength |
| EN ISO 6708:1995 | Pipework components - Definition and selection of DN (nominal size) (ISO 6708:1995) |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| ISO 7091:2000 | Plain washers Normal series Product grade C |
| EN 1333:2006 | Flanges and their joints - Pipework components - Definition and selection of PN |
| ISO 9001:2015 | Quality management systems — Requirements |
| EN 15542:2008 | Ductile iron pipes, fittings and accessories - External cement mortar coating for pipes - Requirements and test methods |
| ISO/IEC Guide 65:1996 | General requirements for bodies operating product certification systems |
| EN 10310:2003 | Steel tubes and fittings for onshore and offshore pipelines - Internal and external polyamide powder based coatings |
| EN 1092-2:1997 | Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 2: Cast iron flanges |
| EN 45012 : 1998 | GENERAL REQUIREMENTS FOR BODIES OPERATING ASSESSMENT AND CERTIFICATION/REGISTRATION OF QUALITY SYSTEMS |
| EN 14901:2014 | Ductile iron pipes, fittings and accessories - Epoxy coating (heavy duty) of ductile iron fittings and accessories - Requirements and test methods |
| EN 15655:2009 | Ductile iron pipes, fittings and accessories - Internal polyurethane lining for pipes and fittings - Requirements and test methods |
| ISO 2531:2009 | Ductile iron pipes, fittings, accessories and their joints for water applications |
| EN 14628:2005 | Ductile iron pipes, fittings and accessories - External polyethylene coating for pipes - Requirements and test methods |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.