I.S. EN 10088-2:2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
STAINLESS STEELS - PART 2: TECHNICAL DELIVERY CONDITIONS FOR SHEET/PLATE AND STRIP OF CORROSION RESISTING STEELS FOR GENERAL PURPOSES
Hardcopy , PDF
English
01-01-2014
11-02-2025
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Designation and ordering
5 Classification of grades
6 Requirements
7 Inspection and testing
8 Marking
Annex A (informative) - Guidelines for further treatment
(including heat treatment) in fabrication
Annex B (informative) - Applicable dimensional standards
Bibliography
Describes the technical delivery conditions for hot or cold rolled sheet/plate and strip of standard grades and special grades of corrosion resisting stainless steels for general purposes.
| DocumentType |
Standard
|
| Pages |
62
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| NBN EN 10088-2 : 2014 | Identical |
| BS EN 10088-2:2014 | Identical |
| NEN EN 10088-2 : 2014 | Identical |
| NS EN 10088-2 : 2014 | Identical |
| EN 10088-2:2014 | Identical |
| NF EN 10088-2 : 2014 | Identical |
| DIN EN 10088-2:2014-12 | Equivalent |
| ONORM EN 10088-2 : 2014 | Identical |
| DIN EN 10088-2:2014-12 | Identical |
| UNE-EN 10088-2:2015 | Identical |
| I.S. 6:2004 | CONCRETE SEWER PIPES |
| S.R. 70:2015 | TIMBER IN CONSTRUCTION - EUROCODE 5 - TRUSSED RAFTERS |
| I.S. 193:2006 | TIMBER TRUSSES FOR ROOFS |
| ISO 9445:2002 | Continuously cold-rolled stainless steel narrow strip, wide strip, plate/sheet and cut lengths — Tolerances on dimensions and form |
| ISO 6507-1:2005 | Metallic materials — Vickers hardness test — Part 1: Test method |
| EN ISO 14284:2002 | Steel and iron - Sampling and preparation of samples for the determination of chemical composition (ISO 14284:1996) |
| EN 10052:1993 | Vocabulary of heat treatment terms for ferrous products |
| EN ISO 6508-1:2016 | Metallic materials - Rockwell hardness test - Part 1: Test method (ISO 6508-1:2016) |
| EN ISO 6506-1:2014 | Metallic materials - Brinell hardness test - Part 1: Test method (ISO 6506-1:2014) |
| EN 10048:1996 | Hot rolled narrow steel strip - Tolerances on dimensions and shape |
| ISO 6506-1:2014 | Metallic materials — Brinell hardness test — Part 1: Test method |
| EN ISO 9445-2:2010 | Continuously cold-rolled stainless steel - Tolerances on dimensions and form - Part 2: Wide strip and plate/sheet (ISO 9445-2:2009) |
| ISO 9444-2:2009 | Continuously hot-rolled stainless steel — Tolerances on dimensions and form — Part 2: Wide strip and sheet/plate |
| EN 10079:2007 | Definition of steel products |
| EN 10027-2:2015 | Designation systems for steels - Part 2: Numerical system |
| CEN/TR 10261:2013 | Iron and steel - European standards for the determination of chemical composition |
| EN ISO 6892-1:2016 | Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1:2016) |
| ISO 15510:2014 | Stainless steels — Chemical composition |
| EN ISO 377:2017 | Steel and steel products - Location and preparation of samples and test pieces for mechanical testing (ISO 377:2017) |
| ISO 6508-1:2016 | Metallic materials — Rockwell hardness test — Part 1: Test method |
| EN ISO 9444-2:2010 | Continuously hot-rolled stainless steel - Tolerances on dimensions and form - Part 2: Wide strip and sheet/plate (ISO 9444-2:2009) |
| EN ISO 9445-1:2010 | Continuously cold-rolled stainless steel - Tolerances on dimensions and form - Part 1: Narrow strip and cut lengths (ISO 9445-1:2009) |
| ISO 6892-1:2016 | Metallic materials — Tensile testing — Part 1: Method of test at room temperature |
| EN ISO 18286:2010 | Hot-rolled stainless steel plates - Tolerances on dimensions and shape (ISO 18286:2008) |
| EN 10151:2002 | Stainless steel strip for springs - Technical delivery conditions |
| EN 10168:2004 | Steel products - Inspection documents - List of information and description |
| EN 10028-7:2016 | Flat products made of steels for pressure purposes - Part 7: Stainless steels |
| ISO 148-1:2016 | Metallic materials — Charpy pendulum impact test — Part 1: Test method |
| EN 10095:1999 | Heat resisting steels and nickel alloys |
| EN 10163-2:2004 | Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 2: Plate and wide flats |
| ISO 9445-2:2009 | Continuously cold-rolled stainless steel — Tolerances on dimensions and form — Part 2: Wide strip and plate/sheet |
| EN 10021:2006 | General technical delivery conditions for steel products |
| ISO 3651-2:1998 | Determination of resistance to intergranular corrosion of stainless steels — Part 2: Ferritic,austenitic and ferritic-austenitic (duplex) stainless steels — Corrosion test in media containing sulfuric acid |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| EN 10307:2001 | Non-destructive testing - Ultrasonic testing of austenitic and austenitic-ferritic stainless steels flat products of thickness equal to or greater than 6 mm (reflection method) |
| EN ISO 6892-2:2011 | Metallic materials - Tensile testing - Part 2: Method of test at elevated temperature (ISO 6892-2:2011) |
| EN ISO 3651-2 : 1998 | DETERMINATION OF RESISTANCE TO INTERGRANULAR CORROSION OF STAINLESS STEELS - FERRITIC, AUSTENITIC AND FERRITIC-AUSTENITIC (DUPLEX) STAINLESS STEELS - CORROSION TEST IN MEDIA CONTAINING SULFURIC ACID |
| EN 10027-1:2016 | Designation systems for steels - Part 1: Steel names |
| ISO 6892-2:2011 | Metallic materials — Tensile testing — Part 2: Method of test at elevated temperature |
| EN ISO 148-1:2016 | Metallic materials - Charpy pendulum impact test - Part 1: Test method (ISO 148-1:2016) |
| ISO 18286:2008 | Hot-rolled stainless steel plates — Tolerances on dimensions and shape |
| EN 10302:2008 | Creep resisting steels, nickel and cobalt alloys |
| ISO 9445-1:2009 | Continuously cold-rolled stainless steel — Tolerances on dimensions and form — Part 1: Narrow strip and cut lengths |
| ISO 377:2017 | Steel and steel products — Location and preparation of samples and test pieces for mechanical testing |
| ISO 14284:1996 | Steel and iron — Sampling and preparation of samples for the determination of chemical composition |
| EN 10088-1:2014 | Stainless steels - Part 1: List of stainless steels |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : Users cannot be edited or removed once added to your Multi user PDF.