I.S. EN 61192-4:2003
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
WORKMANSHIP REQUIREMENTS FOR SOLDERED ELECTRONIC ASSEMBLIES - TERMINAL ASSEMBLIES
Hardcopy , PDF
29-05-2019
English
25-04-2003
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 General requirements
4.1 Classification
4.2 Conflict
4.3 Inspection technique
4.4 Interpretation of requirements
5 Process characterization
5.1 Wire preparation processes
5.2 Terminal mounting processes
5.3 Soldering terminal
5.4 Solderability
5.5 Preconditioning
5.6 Mechanical securing
6 Wire preparation attributes
6.1 Insulation stripping
6.2 Twisted strands
7 Connector pins and terminals
7.1 Soldered connector pins
8 Discrete wiring (jumper wires)
8.1 Wire selection
8.2 Wire routing
8.3 Staking
8.4 Termination
9 Discrete wiring (jumper wires) attributes
10 Solder joint acceptance
10.1 Post terminations
Figures
Table
Provides general requirements for workmanship in terminal soldered assemblies on organic substrates, on printed boards, and on similar laminates attached to the surface(s) of inorganic substrates.
| DevelopmentNote |
For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
|
| DocumentType |
Standard
|
| Pages |
73
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Withdrawn
|
| Standards | Relationship |
| NF EN 61192-4 : 2003 | Identical |
| EN 61192-4:2003 | Identical |
| NBN EN 61192-4 : 2004 | Identical |
| IEC 61192-4:2002 | Identical |
| BS EN 61192-4:2003 | Identical |
| DIN EN 61192-4:2003-11 | Identical |
| IEC 61192-3:2002 | Workmanship requirements for soldered electronic assemblies - Part 3: Through-hole mount assemblies |
| EN 60749 : 99 AMD 2 2001 | SEMICONDUCTOR DEVICES - MECHANICAL AND CLIMATIC TEST METHODS |
| EN 61189-3:2008 | Test methods for electrical materials, printed boards and other interconnection structures and assemblies - Part 3: Test methods for interconnection structures (printed boards) |
| IEC 61189-3:2007 | Test methods for electrical materials, printed boards and other interconnection structures and assemblies - Part 3: Test methods for interconnection structures (printed boards) |
| IEC 61191-1:2013 | Printed board assemblies - Part 1: Generic specification - Requirements for soldered electrical and electronic assemblies using surface mount and related assembly technologies |
| IEC 61192-1:2003 | Workmanship requirements for soldered electronic assemblies - Part 1: General |
| EN 61192-3:2003 | Workmanship requirements for soldered electronic assemblies - Part 3: Through-hole mount assemblies |
| IEC 60194:2015 | Printed board design, manufacture and assembly - Terms and definitions |
| IEC 60749:1996+AMD1:2000+AMD2:2001 CSV | Semiconductor devices - Mechanical and climatic test methods |
| IEC 61191-4:2017 | Printed board assemblies - Part 4: Sectional specification - Requirements for terminal soldered assemblies |
| EN 61191-1:2013 | PRINTED BOARD ASSEMBLIES - PART 1: GENERIC SPECIFICATION - REQUIREMENTS FOR SOLDERED ELECTRICAL AND ELECTRONIC ASSEMBLIES USING SURFACE MOUNT AND RELATED ASSEMBLY TECHNOLOGIES (IEC 61191-1:2013) |
| IEC 61192-2:2003 | Workmanship requirements for soldered electronic assemblies - Part 2: Surface-mount assemblies |
| EN 61192-1:2003 | Workmanship requirements for soldered electronic assemblies - Part 1: General |
| EN 61191-4:2017 | Printed board assemblies - Part 4: Sectional specification - Requirements for terminal soldered assemblies |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.