IEC 60352-5:2012
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Solderless connections - Part 5: Press-in connections - General requirements, test methods and practical guidance
Amended by
Available format(s)
Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users
Superseded date
31-12-2021
Superseded by
Published date
22-02-2012
Publisher
Important note : Users cannot be edited or removed once added to your Multi user PDF.
FOREWORD
INTRODUCTION
1 Scope and object
2 Normative references
3 Terms and definitions
4 Requirements
5 Tests
Annex A (informative) - Practical guidance
Bibliography
IEC 60352-5:2012 is applicable to solderless press-in connections for use in telecommunication equipment and in electronic devices employing similar techniques. The press-in connection consists of a termination having a suitable press-in zone which is inserted into a plated-through hole of a double-sided or multilayer printed board. Information on materials and data from industrial experience is included in addition to the test procedures to provide electrically stable connections under prescribed environmental conditions. The object of this part of IEC 60352 is to determine the suitability of press-in connections under mechanical, electrical and atmospheric conditions as specified by the manufacturer of the press-in termination and to provide a means of comparing test results when the tools used to make the connections are of different designs or manufacture. This fourth edition cancels and replaces the third edition published in 2008. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- enhancement of Annex A and further application remarks are added;
- editorial changes throughout the standard to prevent the document from being misunderstood as specification for establishing press-in connection in total;
- deletion of all tables with hole dimensions. Historically the hole dimensions were constrained because of the dimensions of the wire wrap and clip connections posts. Since these connection technologies are no longer commonly used, the design requirements are no longer practical;
- inclusion of additional figures and one table in 4.4.4 to define tolerance ranges for holes in test-boards and to illustrate them;
- inclusion of a requirement for the thickness of the test-board in 4.4. The contents of the corrigendum of September 2014 have been included in this copy.
| DevelopmentNote |
Stability Date: 2018. (09/2017)
|
| DocumentType |
Standard
|
| Pages |
66
|
| PublisherName |
International Electrotechnical Committee
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| OVE/ONORM EN 60352-5 : 2012 | Identical |
| NF EN 60352-5 : 2012 | Identical |
| NBN EN 60352-5 : 2012 COR 2015 | Identical |
| NEN EN IEC 60352-5 : 2012 C1 2014 | Identical |
| PN EN 60352-5 : 2012 AC 1 2015 | Identical |
| SAC GB/T 18290.5 : 2000 | Identical |
| BS EN 60352-5:2012 | Identical |
| CEI EN 60352-5 : 2013 | Identical |
| EN 60352-5:2012/AC:2014 | Identical |
| DIN EN 60352-5:2012-10 | Identical |
| PNE-FprEN 60352-5 | Identical |
| UNE-EN 60352-5:2012 | Identical |
| UNE-EN 60352-5:2002 | Identical |
| NEN 10352-5 : 1995 | Identical |
| BS EN 61076-4-102:1997 | Connectors with assessed quality, for use in d.c., low-frequency analogue and in digital high speed data applications. Printed board connectors Detail specification for two-part single-pole connectors, for multiple uses on plug-in units, with pre-centring, coding and early mating features, having a metric grid in accordance with IEC 60917 |
| NF EN 61076 4 100 : 2002 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-100: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR TWO-PART CONNECTOR MODULES HAVING A GRID OF 2,5 MM FOR PRINTED BOARDS AND BACKPLANES |
| 12/30270756 DC : 0 | BS EN 61076-3-104 - CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 3-104: DETAIL SPECIFICATION FOR 8-WAY, SHIELDED FREE AND FIXED CONNECTORS FOR DATA TRANSMISSIONS WITH FREQUENCIES UP TO 2000 MHZ |
| BS ISO/IEC 11801-1:2017 | Information technology. Generic cabling for customer premises General requirements |
| I.S. CECC 75301-802:1995 | RECTANGULAR CONNECTORS FOR FREQUENCIES BELOW 3 MHZ, TRAPEZOIDAL SHAPED SHELLS AND ROUND CONTACTS 01 MM WITH CRIMP, SOLDER AND PRESS-IN TERMINANONS FOR PRINTED BOARDS |
| 00/201724 DC : DRAFT APR 2000 | IEC 61076-1 - CONNECTORS - PRODUCT REQUIREMENTS - PART 1: GENERIC SPECIFICATION |
| BS EN 61076-4-101:2001 | Connectors for electronic equipment Printed board connectors with assessed quality. Detail specification for two-part connector modules, having a basic grid of 2,0 mm for printed boards and backplanes in accordance with IEC 60917 |
| 10/30210450 DC : 0 | BS EN 61076-4-116 - CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 4-116: PRINTED BOARD CONNECTORS: DETAIL SPECIFICATION FOR A HIGH-SPEED TWO-PART CONNECTOR WITH INTEGRATED SHIELDING FUNCTION |
| CSA T568.2-4 : 2005 : R2010 | COMMERCIAL BUILDING TELECOMMUNICATIONS CABLING STANDARD - PART 2: BALANCED TWISTED PAIR CABLING COMPONENTS - ADDENDUM 4 - SOLDERLESS CONNECTION RELIABILITY REQUIREMENTS FOR COPPER CONNECTING HARDWARE |
| CSA T568.2-4 :2005 | COMMERCIAL BUILDING TELECOMMUNICATIONS CABLING STANDARD - PART 2: BALANCED TWISTED PAIR CABLING COMPONENTS - ADDENDUM 4 - SOLDERLESS CONNECTION RELIABILITY REQUIREMENTS FOR COPPER CONNECTING HARDWARE |
| 03/100395 DC : DRAFT APR 2003 | EN 175101-809 - DETAIL SPECIFICATION - TWO-PART CONNECTORS FOR PRINTED BOARDS HAVING A GRID OF 2,54 MM, SHORT VERSION IN COMPLIANCE WITH CECC 75 101-801, WITH ASSESSED QUALITY |
| 02/206147 DC : DRAFT AUG 2002 | IEC 60603-7-4 ED.1.0 - CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 7-4: DETAIL SPECIFICATION FOR 8-WAY, UNSHIELDED, FREE AND FIXED CONNECTORS, FOR DATA TRANSMISSIONS WITH FREQUENCIES UP TO 250 MHZ (CAT 6, UNSHIELDED) |
| UNE-EN 50467:2012 | Railway applications - Rolling stock - Electrical connectors, requirements and test methods |
| I.S. EN 61076-4-101:2002 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-101: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR TWO-PART CONNECTOR MODULES, HAVING A BASIC GRID OF 2,0 MM FOR PRINTED BOARDS AND BACKPLANES IN ACCORDANCE WITH IEC 60917 |
| NF EN 62852 : 2015 | CONNECTORS FOR DC-APPLICATION IN PHOTOVOLTAIC SYSTEMS - SAFETY REQUIREMENTS AND TESTS |
| BS EN 61076-4-116 : 2012 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 4-116: PRINTED BOARD CONNECTORS - DETAIL SPECIFICATION FOR A HIGH-SPEED TWO-PART CONNECTOR WITH INTEGRATED SHIELDING FUNCTION |
| I.S. EN 50467:2011 | RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS |
| I.S. EN 62852:2015 | CONNECTORS FOR DC-APPLICATION IN PHOTOVOLTAIC SYSTEMS - SAFETY REQUIREMENTS AND TESTS |
| BS EN 50548 : 2011 | JUNCTION BOXES FOR PHOTOVOLTAIC MODULES |
| CEI EN 61076-4-111 : 2003 | CONNECTORS FOR ELECTRONIC EQUIPMENT PART 4-111: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR TWO-PART POWER CONNECTOR MODULES, FOR PRINTED BOARDS AND BACKPLANES HAVING EARLY MATING FEATURES, AND HAVING A BASIC GRID OF 2,5 MM IN ACCORDANCE WITH IEC 60917-1 |
| I.S. EN 50548:2011 | JUNCTION BOXES FOR PHOTOVOLTAIC MODULES |
| I.S. EN 61076-4-103:1999 | CONNECTORS FOR USE IN D.C. LOW-FREQUENCY ANALOGUE AND DIGITAL HIGH SPEED DATA APPLICATIONS - PART 4-103: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR TWO-PART CONNECTORS WITH SHIELDING AND A BASIC GRID OF 2.5 MM |
| BS IEC 62852 : 2014 | CONNECTORS FOR DC-APPLICATION IN PHOTOVOLTAIC SYSTEMS - SAFETY REQUIREMENTS AND TESTS |
| IEC 61076-4-111:2002 | Connectors for electronic equipment - Part 4-111: Printed board connectors with assessed quality - Detail specification for two-part power connector modules, for printed boards and backplanes having early mating features, and having a basic grid of 2,5 mm in accordance with IEC 60917-1 |
| EN 61076-4-108:2002 | Connectors for electronic equipment - Part 4-108: Printed board connectors with assessed quality - Detail specification for cable-to-board connectors, with a modular pitch of 25 mm and integrated shielding function, applicable for transverse packing density of 15 mm, having a basic grid of 2,5 mm in accordance with IEC 60917-1 |
| EN 61076-4-101:2001 | Connectors for electronic equipment - Part 4-101: Printed board connectors with assessed quality - Detail specification for two-part connector modules, having a basic grid of 2,0 mm for printed boards and backplanes in accordance with IEC 60917 |
| EN 61076-4-114:2003 | Connectors for electronic equipment - Part 4-114: Printed board connectors - Detail specification for two-part connector with integrated shielding function having a grid of 1 mm x 1,5 mm |
| EN 60603-13:1998 | Connectors for frequencies below 3 MHz for use with printed boards - Part 13: Detail specification for two-part connectors of assessed quality, for printed boards for basic grid of 2,54 mm (0,1 in), with free connectors for non-accessible insulation displacement terminations (ID) |
| EN 61076-4-103:1999 | Connectors for use in d.c. low-frequency analogue and digital high speed data applications - Part 4-103: Printed board connectors with assessed quality - Detail specification for two-part connectors with shielding and a basic grid of 2,5 mm |
| EN 61076-4-102:1997 | Connectors with assessed quality, for use in d.c., low-frequency analogue and in digital high speed data applications - Part 4: Printed board connectors - Section 102: Detail specification for two-part single-pole connectors, for multiple uses on plug-in units, with pre-centring, coding and early mating features, having a metric grid in accordance with IEC 60917 |
| EN 61076-4-113:2003 | Connectors for electronic equipment - Printed board connectors - Part 4-113: Detail specification for two-part connectors having 5 rows with a grid of 2,54 mm for printed boards and backplanes in bus applications |
| EN 61076-4-110:2002 | Connectors for electronic equipment - Part 4-110: Printed board connectors with assessed quality - Detail specification for latched cable connector system having a basic grid of 2,0 mm including full shielding and latching function |
| DIN EN 60352-1:1998-04 | SOLDERLESS CONNECTIONS - PART 1: WRAPPED CONNECTIONS - GENERAL REQUIREMENTS, TEST METHODS AND PRACTICAL GUIDANCE |
| BS EN 61076-4:1997 | Connectors with assessed quality, for use in d.c., low-frequency analogue and in digital high speed data applications Sectional specification. Printed board connectors |
| I.S. EN 61076-4:1998 | CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D.C., LOW FREQUENCY ANALOGUE AND IN DIGITAL HIGH-SPEED DATA APPLICATIONS - PART 4: SECTIONAL SPECIFICATION - PRINTED BOARD CONNECTORS |
| 12/30235292 DC : 0 | BS EN 50343 - RAILWAY APPLICATIONS - ROLLING STOCK - RULES FOR INSTALLATION OF CABLING |
| CEI EN 61076-4-110 : 2003 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-110: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR LATCHED CABLE CONNECTOR SYSTEM HAVING A BASIC GRID OF 2,0 MM INCLUDING FULL SHIELDING AND LATCHING FUNCTION |
| NF EN 50521 : 2009 AMD 1 2012 | CONNECTORS FOR PHOTOVOLTAIC SYSTEMS - SAFETY REQUIREMENTS AND TESTS |
| BS EN 61076-4-103:1999 | Connectors with assessed quality, for use in d.c., low-frequency analogue and in digital high speed data applications. Printed board connectors Detail specification for two-part connectors with shielding and a basic grid of 2,5 mm - Cable to board connectors, shielded against EMC ,grid 2,5 mm,for high speed data rates,for use with printed boards |
| NF EN 61076 4 115 : 2003 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-115: PRINTED BOARD CONNECTORS - BACKPLANE CONNECTOR FOR INFINIBAND EQUIPMENT |
| 06/30152213 DC : DRAFT JUNE 2006 | BS EN 60603-7-1 ED. 2 - CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 7-1: DETAIL SPECIFICATION FOR 8-WAY, SHIELDED, FREE AND FIXED CONNECTORS |
| BS EN 61076-4-104:1999 | Connectors for electronic equipment. Printed board connectors with assessed quality Detail specification for two-part modular connectors, basic grid of 2,0 mm, with terminations on a multiple grid of 0,5 mm - Detail specification for two part modular connectors (with optional shielding plates) for printed boards and backplanes, basic grid 2,0 mm, with terminations on a multiple grid of 0,5 mm |
| CEI EN 50467 : 2013 | RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS |
| 03/100166 DC : DRAFT JAN 2003 | IEC 60603-7-5 ED.1.0 - CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 7-5: DETAIL SPECIFICATION FOR 8-WAY, SHIELDED, FREE AND FIXED CONNECTORS, FOR DATA TRANSMISSIONS WITH FREQUENCIES UP TO 250 MHZ |
| 03/100167 DC : DRAFT JAN 2003 | IEC 60603-3-105 ED.1 - CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 3-105: DETAIL SPECIFICATION FOR 4 PAIR BALANCED, INDIVIDUALLY SHIELDED, FIXED AND FREE CONNECTORS WITH CHARACTERISTIC IMPEDENCE OF 100 OHMS, COVERING A FREQUENCY RANGE FROM DC TO 1500 MHZ |
| BS EN 61076-4-113:2003 | Connectors for electronic equipment Printed board connectors with assessed quality Detail specification for two-part connectors having 5 rows with a grid of 2,54 mm for printed boards and backplanes in bus applications |
| PREN 50467 : DRAFT 2009 | RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS |
| CEI EN 61076-4-115 : 2004 | CONNECTORS FOR ELECTRONIC EQUIPMENT PART 4-115: PRINTED BOARD CONNECTORS BACKPLANE CONNECTOR FOR INFINIBAND EQUIPMENT |
| BS EN 60352-1:1998 | Solderless connections Wrapped connections. General requirements, test methods and practical guidance |
| I.S. EN 61076-4-111:2002 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRINTED BOARD CONNECTORS WITH ASSESSED QUALIFY - DETAIL SPECIFICATION FOR TWO-PART POWER CONNECTOR MODULES, FOR PRINTED BOARDS AND BACKPLANES HAVING EARLY MATING FEATURES, AND HAVING A BASIC GRID OF 2,5 MM IN ACCORDANCE WITH IEC 60917-1 |
| CEI EN 50343 : 2015 | RAILWAY APPLICATIONS - ROLLING STOCK - RULES FOR INSTALLATION OF CABLING |
| BS EN 60603-7 : 2009 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 7: DETAIL SPECIFICATION FOR 8-WAY, UNSHIELDED, FREE AND FIXED CONNECTORS |
| NF EN 61076 4 113 : 2005 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRINTED BOARD CONNECTORS - PART 4-113: DETAIL SPECIFICATION FOR TWO-PART CONNECTORS HAVING 5 ROWS WITH A GRID OF 2,54 MM FOR PRINTED BOARDS AND BACKPLANES IN BUS APPLICATIONS |
| IEC PAS 61076-3-126:2018 | Connectors for electrical and electronic equipment - Product requirements - Part 3-126: Rectangular connectors - Detail specification for 5 pole power connector for industrial environments with push-pull locking |
| 17/30355792 DC : 0 | BS EN 62790 AMENDMENT 1 - JUNCTION BOXES FOR PHOTOVOLTAIC MODULES - SAFETY REQUIREMENTS AND TESTS |
| EN 60603-7:2009/A1:2011 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 7: DETAIL SPECIFICATION FOR 8-WAY, UNSHIELDED, FREE AND FIXED CONNECTORS (IEC 60603-7:2008/A1:2011) |
| 11/30244521 DC : 0 | BS EN 61076-3-100 - CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 3-110: DETAIL SPECIFICATION FOR SHIELDED, FREE AND FIXED CONNECTORS FOR DATA TRANSMISSION WITH FREQUENCIES UP TO 1000 MHZ |
| CEI EN 61076-4-100 : 2003 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-100: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR TWO-PART CONNECTOR MODULES HAVING A GRID OF 2,5 MM FOR PRINTED BOARDS AND BACKPLANES |
| CEI EN 61076-4 : 1997 | CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D.C., LOW FREQUENCY ANALOGUE AND IN DIGITAL HIGH-SPEED DATA APPLICATIONS - PART 4: SECTIONAL SPECIFICATION PRINTED BOARD CONNECTORS |
| CEI EN 61076-4-114 : 2004 | CONNECTORS FOR ELECTRONIC EQUIPMENT PART 4-114: PRINTED BOARD CONNECTORS - DETAIL SPECIFICATION FOR TWO-PART CONNECTOR WITH INTEGRATED SHIELDING FUNCTION HAVING A GRID OF 1 MM X 1,5 MM |
| CEI EN 61076-4-108 : 2003 | CONNECTORS FOR ELECTRONIC EQUIPMENT PART 4-108: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY DETAIL SPECIFICATION FOR CABLE-TO-BOARD CONNECTORS, WITH A MODULAR PITCH OF 25 MM AND INTEGRATED SHIELDING FUNCTION, APPLICABLE FOR TRANSVERSE PACKING DENSITY OF 15 MM, HAVING A BASIC GRID OF 2,5 MM IN ACCORDANCE WITH IEC 60917-1 |
| DD CLC/TS 50467:2008 | Railway applications. Rolling stock. Electrical connectors, requirements and test methods |
| 03/100530 DC : DRAFT JUNE 2003 | IEC 61076-3 ED 2 - CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 3: RECTANGULAR CONNECTORS - SECTIONAL SPECIFICATION |
| CECC 75301-802 : 1994 | RECTANGULAR CONNECTORS FOR FREQUENCIES BELOW 3 MHZ, TRAPEZOIDAL SHAPED SHELLS AND ROUND CONTACTS 01 MM WITH CRIMP, SOLDER AND PRESS-IN TERMINANONS FOR PRINTED BOARDS |
| I.S. EN 61076-4-113:2003 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRINTED BOARD CONNECTORS - PART 4-113: DETAIL SPECIFICATION FOR TWO-PART CONNECTORS HAVING 5 ROWS WITH A GRID OF 2,54 MM FOR PRINTED BOARDS AND BACKPLANES IN BUS APPLICATIONS |
| 04/30124126 DC : DRAFT OCT 2004 | IEC 61076-2-104 ED.1 - CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 2-104: CIRCULAR CONNECTORS - DETAIL SPECIFICATION FOR M8 CONNECTORS WITH SCREW OR SNAP-LOCKING FOR LOW VOLTAGE APPLICATIONS |
| BS EN 50343 : 2014 | RAILWAY APPLICATIONS - ROLLING STOCK - RULES FOR INSTALLATION OF CABLING |
| BS EN 60603-13:1998 | Connectors for frequencies below 3 MHz for use with printed boards Detail specification for two-part connectors of assessed quality, for printed boards for basic grid of 2,54 mm (0,1 in) with free connectors for non-accessible insulation displacement terminations (ID) |
| IEC PAS 60603-7-3:2004 | Connectors for electronic equipment - Part 7-3: Detail specification for 8-way, shielded, free and fixed connectors, for data transmissions with frequencies up to 100 MHz |
| BS EN 61076-4-115:2003 | Connectors for electronic equipment. Printed board connectors with assessed quality Backplane connector for InfiniBand equipment |
| BS EN 61243-5:2001 | Live working. Voltage detectors Voltage detecting systems (VDS) |
| NF EN 60603-7-3 : DEC 2010 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 7-3: DETAIL SPECIFICATION FOR 8-WAY, SHIELDED, FREE AND FIXED CONNECTORS, FOR DATA TRANSMISSIONS WITH FREQUENCIES UP TO 100 MHZ |
| EN IEC 61076-2-111:2018 | Connectors for electrical and electronic equipment - Product requirements - Part 2-111: Circular connectors - Detail specification for power connectors with M12 screw-locking |
| NF EN 61076 4 101 : 2002 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-101: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR TWO-PART CONNECTOR MODULES, HAVING A BASIC GRID OF 2,0 MM FOR PRINTED BOARDS AND BLACKPLANES IN ACCORDANCE WITH IEC 60917 |
| I.S. EN 61076-4-102:1998 | CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D.C., LOW-FREQUENCY ANALOGUE AND IN DIGITAL HIGH SPEED DATA APPLICATIONS - PART 4: PRINTED BOARD CONNECTORS - SECTION 102: DETAIL SPECIFICATION FOR TWO-PART SINGLE-POLE CONNECTORS, FOR MULTIPLE USES ON PLUG-IN UNITS, WITH PRE-CENTRING, CODING AND EARLY MATING FEATURES, HAVING A METRIC GRID IN ACCORDANCE WITH IEC 60917 |
| BS EN 50173-1:2011 | Information technology. Generic cabling systems General requirements |
| I.S. EN 60947-7-4:2013 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 7-4: ANCILLARY EQUIPMENT - PCB TERMINAL BLOCKS FOR COPPER CONDUCTORS (IEC 60947-7-4:2013 (EQV)) |
| ISO/IEC 14575:2000 | Information technology — Microprocessor systems — Heterogeneous InterConnect (HIC) (Low-Cost, Low-Latency Scalable Serial Interconnect for Parallel System Construction) |
| CECC 75101-807 : 1994 | MODULAR TWO-PART CONNECTORS FOR PRINTED BOARDS AND BACKPLANES, GRIDOF 2.5 mm - ACCORDING TO IEC 917 (DETAIL SPECIFICATION) |
| EN 50173-1:2011 | Information technology - Generic cabling systems - Part 1: General requirements |
| I.S. EN 61076-3-104:2017 | CONNECTORS FOR ELECTRICAL AND ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 3-104: DETAIL SPECIFICATION FOR 8-WAY, SHIELDED FREE AND FIXED CONNECTORS FOR DATA TRANSMISSIONS WITH FREQUENCIES UP TO 2000 MHZ |
| I.S. EN 61984:2009 | CONNECTORS - SAFETY REQUIREMENTS AND TESTS |
| IEC 61076-3-104:2017 | Connectors for electrical and electronic equipment - Product requirements - Part 3-104: Detail specification for 8-way, shielded free and fixed connectors for data transmissions with frequencies up to 2 000 MHz |
| I.S. CECC 75101-807:1994 | MODULAR TWO-PART CONNECTORS FOR PRINTED BOARDS AND BACKPLANES, GRID OF 2.5 MM - (ACCORDING TO IEC 917) (DETAIL SPECIFICATION) |
| IEC 61076-4-110:2001 | Connectors for electronic equipment - Part 4-110: Printed board connectors with assessed quality - Detail specification for latched cable connector system having a basic grid of 2,0 mm including full shielding and latching function |
| S.R. CLC/TS 50467:2008 | RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS |
| EN 175101-809:2004/corrigendum Jun. 2005 | DETAIL SPECIFICATION: TWO-PART CONNECTORS FOR PRINTED BOARDS HAVING A GRID OF 2,54 MM, SHORT VERSION IN COMPLIANCE WITH CECC 75 101-801, WITH ASSESSED QUALITY |
| IEC 61076-4-113:2002 | Connectors for electronic equipment - Printed board connectors - Part 4-113: Detail specification for two-part connectors having 5 rows with a grid of 2,54 mm for printed boards and backplanes in bus applications |
| IEC 60603-7:2008+AMD1:2011 CSV | Connectors for electronic equipment - Part 7: Detail specification for 8-way, unshielded, free and fixed connectors |
| UNE-EN 50521:2010 | Connectors for photovoltaic systems - Safety requirements and tests |
| EN 61076-4:1996 | Connectors with assessed quality, for use in d.c., low frequency analogue and in digital high-speed data applications - Part 4: Sectional specification - Printed board connectors |
| CEI EN 61243-5 : 2002 | LIVE WORKING - VOLTAGE DETECTORS - PART 5: VOLTAGE DETECTING SYSTEMS (VDS) |
| CEI EN 61076-4-103 : 2001 | CONNECTORS FOR USE IN D.C. LOW - FREQUENCY ANALOGUE AND DIGITAL HIGH SPEED DATA APPLICATIONS PART 4-103: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY DETAIL SPECIFICATION FOR TWO-PART CONNECTORS WITH SHIELDING AND A BASIC GRID OF 2,5 MM |
| 02/206148 DC : 0 | IEC 60603-7-5. ED. 1.0 - CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 7-5: DETAIL SPECIFICATION FOR 8-WAY, SHIELDED, FREE AND FIXED CONNECTORS, FOR DATA TRANSMISSIONS WITH FREQUENCIES UP TO 250 MHZ (CAT 6, SHIELDED) |
| NF EN 60603-7 : 2010 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 7: DETAIL SPECIFICATION FOR 8-WAY, UNSHIELDED, FREE AND FIXED CONNECTORS |
| NF EN 61076 4 102 : 1998 | CONNECTORS WITH ASSESSED QUALITY FOR USE IN D.C., LOW-FREQUENCY ANALOGUE AND IN DIGITAL HIGH SPEED DATA APPLICATIONS - PART 4: PRINTED BOARD CONNECTORS - SECTION 102: DETAIL SPECIFICATION FOR TWO-PART SINGLE-POLE CONNECTORS, FOR MULTIPLE USES ON PLUG-IN UNITS, WITH PRE-CENTERING, CODING AND EARLY MATING FEATURES, HAVING A METRIC GRID IN ACCORDANCE WITH IEC 60917 |
| NF EN 61076 4 107 : 2002 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-107: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR SHIELDED TWO-PART CONNECTORS HAVING A BASIC GRID OF 2,0 MM, FIXED PART WITH SOLDER AND PRESS-IN TERMINATIONS FOR PRINTED BOARDS, FREE PART WITH NON-ACCESSIBLE INSULATION DISPLACEMENT AND CRIMP TERMINATIONS |
| CEI EN 60947-7-4 : 2014 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 7-4: ANCILLARY EQUIPMENT - PCB TERMINAL BLOCKS FOR COPPER CONDUCTORS |
| BS EN 61076-4-111:2002 | Connectors for electronic equipment. Printed board connectors with assessed quality Detail specification for two-part power connector modules, for printed boards and backplanes having early mating features, and having a basic grid of 2,5 mm in accordance with IEC 60917-1 |
| UNE-EN 60947-7-4:2014 | Low-voltage switchgear and controlgear - Part 7-4: Ancillary equipment - PCB terminal blocks for copper conductors |
| EN IEC 61076-3-119:2018 | Connectors for electrical and electronic equipment - Product requirements - Part 3-119: Rectangular connectors - Detail specification for shielded and unshielded, free and fixed 10-way connectors with push-pull coupling for industrial environments for data transmission with frequencies up to 100 MHz |
| 11/30206085 DC : 0 | BS EN 60947-7-4 - LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 7-4: ANCILLARY EQUIPMENT - PRINTED BOARD TERMINAL BLOCKS FOR COPPER CONDUCTORS |
| 16/30325971 DC : 0 | BS ISO/IEC 11801-1 - INFORMATION TECHNOLOGY - GENERIC CABLING FOR CUSTOMER PREMISES - PART 1: GENERAL REQUIREMENTS |
| BS EN 61076-4-110:2002 | Connectors with assessed quality, for use in d.c., low-frequency analogue and in digital high speed data applications. Printed board connectors Detail specification for latched cable connector system having a basic grid of 2,0 mm including full shielding and latching function |
| NF EN 60603-7-4 : 2010 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 7-4: DETAIL SPECIFICATION FOR 8-WAY, UNSHIELDED, FREE AND FIXED CONNECTORS, FOR DATA TRANSMISSIONS WITH FREQUENCIES UP TO 250 MHZ |
| BS EN 61076-4-108:2002 | Connectors for electronic equipment. Printed board connectors with assessed quality Detail specification for cable-to-board connectors, with a modular pitch of 25 mm and integrated shielding function, applicable for transverse packing density of 15 mm, having a basic grid of 2,5 mm in accordance with IEC 60917-1 |
| 03/100336 DC : DRAFT MAR 2003 | IEC 60603-7-7 - CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 7-7: DETAIL SPECIFICATION FOR 8-WAY, SHIELDED, FREE AND FIXED CONNECTORS FOR DATA TRANSMISSION WITH FREQUENCIES UP TO 600 MHZ |
| 03/100165 DC : DRAFT JAN 2003 | IEC 60603-7-2 ED.1.0 - CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 7-2: DETAIL SPECIFICATION FOR 8-WAY, UNSHIELDED, FREE AND FIXED CONNECTORS, FOR DATA TRANSMISSION WITH FREQUENCIES UP TO 100 MHZ |
| UL 60947-7-4:1ED 2018-04-27 | Low-Voltage Switchgear and Controlgear - Part 7-4: Ancillary equipment - PCB terminal blocks for copper conductors |
| I.S. EN 60603-7:2009 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 7: DETAIL SPECIFICATION FOR 8-WAY, UNSHIELDED, FREE AND FIXED CONNECTORS (IEC 60603-7:2008) |
| I.S. EN 61076-4-116:2012 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 4-116: PRINTED BOARD CONNECTORS - DETAIL SPECIFICATION FOR A HIGH-SPEED TWO-PART CONNECTOR WITH INTEGRATED SHIELDING FUNCTION |
| I.S. EN 61076-4-110:2002 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-110: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR LATCHED CABLE CONNECTOR SYSTEM HAVING A BASIC GRID OF 2,0 MM INCLUDING FULL SHIELDING AND LATCHING FUNCTION |
| IEEE DRAFT 1355 : D1.4 FEB 95 | STANDARD FOR HETEROGENOUS INTERCONNECT (HIC) (LOW COST LOW LATENCY SCALABLE SERIAL INTERCONNECT FOR PARALLEL SYSTEM CONSTRUCTION) |
| BS EN 60947-7-4:2013 | Low-voltage switchgear and controlgear Ancillary equipment. PCB terminal blocks for copper conductors |
| CEI EN 60352-1 : 1998 | SOLDERLESS CONNECTIONS - PART 1: WRAPPED CONNECTIONS - GENERAL REQUIREMENTS, TEST METHODS AND PRACTICAL GUIDANCE |
| I.S. EN 50343:2014 | RAILWAY APPLICATIONS - ROLLING STOCK - RULES FOR INSTALLATION OF CABLING |
| I.S. EN 61076-4-104:1999 | CONNECTORS FOR USE IN D.C. LOW-FREQUENCY ANALOGUE AND DIGITAL HIGH-SPEED DATA APPLICATIONS - PART 4-104: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR TWO-PART MODULAR CONNECTORS, BASIC GRID OF 2.0 MM WITH TERMINATIONS ON A MULTIPLE GRID OF 0.5 MM |
| EN 61076-4-116:2012/A1:2016 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 4-116: PRINTED BOARD CONNECTORS - DETAIL SPECIFICATION FOR A HIGH-SPEED TWO-PART CONNECTOR WITH INTEGRATED SHIELDING FUNCTION (IEC 61076-4-116:2012/A1:2015) |
| IEC 61076-4-101:2001 | Connectors for electronic equipment - Part 4-101: Printed board connectors with assessed quality - Detail specification for two-part connector modules, having a basic grid of 2,0 mm for printed boards and backplanes in accordance with IEC 60917 |
| BS EN 61984:2009 | Connectors. Safety requirements and tests |
| IEC 61076-4-100:2001 | Connectors for electronic equipment - Part 4-100: Printed board connectors with assessed quality - Detail specification for two-part connector modules having a grid of 2,5 mm for printed boards and backplanes |
| IEC 61984:2008 | Connectors - Safety requirements and tests |
| IEC 61076-4-115:2003 | Connectors for electronic equipment - Part 4-115: Printed board connectors - Backplane connector for InfiniBand equipment |
| EN 62852:2015 | Connectors for DC-application in photovoltaic systems - Safety requirements and tests |
| 05/30128512 DC : DRAFT JAN 2005 | IEC 61984 ED.2 - CONNECTORS - SAFETY REQUIREMENTS AND TESTS |
| IEC 61076-4-102:1997 | Connectors with assessed quality for use in d.c., low-frequencyanalogue and in digital high speed data applications - Part 4:Printed board connectors - Section 102: Detail specification fortwo-part single-pole connectors, for multiple uses on plug-inunits, with pre-centring, coding and early mating features, havinga metric grid in accordance with IEC 60917 |
| IEC 61076-4-108:2002 | Connectors for electronic equipment - Part 4-108: Printed board connectors with assessed quality - Detail specification for cable-to-board connectors, with a modular pitch of 25 mm and integrated shielding function, applicable for transverse packing density of 15 mm, having a basic grid of 2,5 mm in accordance with IEC 60917-1 |
| IEC 60947-7-4:2013 | Low-voltage switchgear and controlgear - Part 7-4: Ancillary equipment - PCB terminal blocks for copper conductors |
| IEC 60603-13:1995 | Connectors for frequencies below 3 MHz for use with printed boards - Part 13: Detail specification for two-part connectors of assessed quality, for printed boards for basic grid of 2,54 mm (0,1 in), with free connectors for non-accessible insulation displacement terminations (ID) |
| BS EN 62852:2015 | Connectors for DC-application in photovoltaic systems. Safety requirements and tests |
| IEC 61076-4-114:2003 | Connectors for electronic equipment - Part 4-114: Printed board connectors - Detail specification for two-part connector with integrated shielding function having a grid of 1 mm x 1,5 mm |
| BS EN 50521 : 2009 | CONNECTORS FOR PHOTOVOLTAIC SYSTEMS - SAFETY REQUIREMENTS AND TESTS |
| 08/30179116 DC : DRAFT MAR 2008 | BS EN 50521 - CONNECTORS FOR PHOTOVOLTAIC SYSTEMS - SAFETY REQUIREMENTS AND TESTS |
| IEC 61076-4-116:2012+AMD1:2015 CSV | Connectors for electronic equipment - Product requirements - Part4-116: Printed board connectors - Detail specification for a high-speed two-part connector with integrated shielding function |
| CLC/TS 50467 : 2008 COR 2008 | RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS |
| BS EN 61076-5:2001 | Connectors with assessed quality, for use in d.c., low-frequency analogue and in digital high speed data applications In-line sockets with assessed quality. Sectional specification |
| I.S. EN 61076-4-114:2003 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-114: PRINTED BOARD CONNECTORS - DETAIL SPECIFICATION FOR TWO-PART CONNECTOR WITH INTEGRATED SHIELDING FUNCTION HAVING A GRID OF 1 MM X 1,5 MM |
| I.S. EN 50173-1:2011 | INFORMATION TECHNOLOGY - GENERIC CABLING SYSTEMS - PART 1: GENERAL REQUIREMENTS |
| CAN/CSA-C22.2 NO. 60947-7-4:18 | Low-voltage switchgear and controlgear ? Part 7-4: Ancillary equipment ? PCB terminal blocks for copper conductors (Trinational standard with NMX-J-538/7-4-ANCE and UL 60974-7-4) |
| 09/30208429 DC : 0 | BS EN 50467 - RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS |
| 04/30124122 DC : DRAFT OCT 2004 | IEC 61076-2-101 ED.2 - CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 2-101: CIRCULAR CONNECTORS. DETAIL SPECIFICATION FOR M12 CONNECTORS WITH SCREW-LOCKING FOR LOW VOLTAGE APPLICATIONS |
| CEI EN 61076-4-104 : 2001 | CONNECTORS FOR USE IN D.C. LOW FREQUENCY ANALOGUE AND DIGITAL HIGH SPEED DATA APPLICATIONS PART 4-104: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY DETAIL SPECIFICATION FOR TWO-PART MODULAR CONNECTORS, BASIC GIRD OF 2,0 MMS WITH TERMINATIONS ON A MULTIPLE GIRD OF 0,5 MM |
| BS EN 61076-4-107:2001 | Connectors for electronic equipment Printed board connectors with assessed quality. Detail specification for shielded two-part connectors having a basic grid of 2,0 mm, fixed part with solder and press-in terminations for printed boards, free part with non-accessible insulation displacement and crimp terminations |
| 09/30213890 DC : 0 | BS EN 61076-3-110 - CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 3-110: DETAIL SPECIFICATION FOR SHIELDED, FREE AND FIXED CONNECTORSFOR DATA TRANSMISSION WITH FREQUENCIES UP TO 1000 MHZ |
| CEI EN 61076-4-102 : 1998 | CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D.C., LOW FREQUENCY ANALOGUE AND IN DIGITAL HIGH SPEED DATA APPLICATIONS - PART 4: PRINTED BOARD CONNECTORS SECTION 102: DETAIL SPECIFICATION FOR TWO-PART SINGLE-POLE CONNECTORS, FOR MULTIPLE USES ON PLUG-IN UNITS, WITH PRE-CENTRING, CODING AND EARLY MATING FEATURES, HAVING A METRIC GRID IN ACCORDANCE WITH IEC 60917 |
| BS EN 50467:2011 | Railway applications. Rolling stock. Electrical connectors, requirements and test methods |
| 09/30210077 DC : 0 | BS EN 50173-1/PRAB - INFORMATION TECHNOLOGY - GENERIC CABLING SYSTEM - PART 1: GENERAL REQUIREMENTS |
| BS EN 175101-809:2004 | Harmonized system of quality assessment for electronic components. Detail specification Two-part connectors for printed boards having a grid of 2,54 mm, short version in compliance with CECC 75 101-801, with assessed quality |
| BS EN 61076-3-104:2017 | Connectors for electrical and electronic equipment. Product requirements Detail specification for 8-way, shielded free and fixed connectors for data transmissions with frequencies up to 2 000 MHz |
| I.S. EN 61076-4-115:2003 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-115: PRINTED BOARD CONNECTORS - BACKPLANE CONNECTOR FOR INFINIBAND EQUIPMENT |
| CEI EN 50173-1 : 2011 | INFORMATION TECHNOLOGY - GENERIC CABLING SYSTEMS - PART 1: GENERAL REQUIREMENTS |
| BS EN 61076-4-100:2002 | Connectors with assessed quality, for use in d.c., low-frequency analogue and in digital high speed data applications. Printed board connectors Detail specification for two-part connector modules having a grid of 2,5 mm for printed boards and backplanes |
| BS EN 61076-4-114:2003 | Connectors for electronic equipment. Printed board connectors with assessed quality Detail specification for two-part connector with integrated shielding function having a grid of 1 mm x 1,5 mm |
| I.S. EN 50521:2008 | CONNECTORS FOR PHOTOVOLTAIC SYSTEMS - SAFETY REQUIREMENTS AND TESTS |
| I.S. EN IEC 61076-3-119:2018 | CONNECTORS FOR ELECTRICAL AND ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 3-119: RECTANGULAR CONNECTORS - DETAIL SPECIFICATION FOR SHIELDED AND UNSHIELDED, FREE AND FIXED 10-WAY CONNECTORS WITH PUSH-PULL COUPLING FOR INDUSTRIAL ENVIRONMENTS FOR DATA TRANSMISSION WITH FREQUENCIES UP TO 100 MHZ |
| I.S. EN IEC 61076-2-111:2018 | CONNECTORS FOR ELECTRICAL AND ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 2-111: CIRCULAR CONNECTORS - DETAIL SPECIFICATION FOR POWER CONNECTORS WITH M12 SCREW-LOCKING |
| ISO/IEC 11801-1:2017 | Information technology — Generic cabling for customer premises — Part 1: General requirements |
| UNE-EN 62852:2015 | Connectors for DC-application in photovoltaic systems - Safety requirements and tests |
| NF EN 61076 4-114 : 2005 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-114: PRINTED BOARD CONNECTORS - DETAIL SPECIFICATION FOR TWO-PART CONNECTOR WITH INTEGRATED SHIELDING FUNCTION HAVING A GRID OF 1 MM X 1,5 MM |
| I.S. EN 61076-4-108:2002 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-108: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR CABLE-TO-BOARD CONNECTORS, WITH A MODULAR PITCH OF 25 MM AND INTEGRATED SHIELDING FUNCTION, APPLICABLE FOR TRANSVERSE PACKING DENSITY OF 15 MM, HAVING A BASIC GRID OF 2,5 MM IN ACCORDANCE WITH IEC 60917-1 |
| I.S. EN 175101-809:2004 | DETAIL SPECIFICATION - TWO-PART CONNECTORS FOR PRINTED BOARDS HAVING A GRID OF 2.54 MM, SHORT VERSION IN COMPLIANCE WITH CECC 75101-801, WITH ASSESSED QUALITY |
| IEC 62847:2016 | Railway applications - Rolling stock - Electrical connectors - Requirements and test methods |
| IEC 61076-5:2001 | Connectors for use in d.c., low-frequency analogue and digital high-speed data applications - Part 5: In-line sockets with assessed quality - Sectional specification |
| EN 61076-3-104:2017 | Connectors for electrical and electronic equipment - Product requirements - Part 3-104: Detail specification for 8-way, shielded free and fixed connectors for data transmissions with frequencies up to 2 000 MHz |
| IEC 61076-4-104:1999 | Connectors for use in d.c., low frequency analogue and digital high speed data applications - Part 4-104: Printed board connectors with assessed quality - Detail specification for two-part modular connectors, basic grid of 2,0 mm, with terminations on a multiple grid of 0,5 mm |
| IEC 62852:2014 | Connectors for DC-application in photovoltaic systems - Safety requirements and tests |
| IEC 61076-4:1995 | Connectors with assessed quality, for use in d.c., low-frequency analogue and in digital high-speed data applications - Part 4: Sectional specification - Printed board connectors |
| EN 50548 : 2011 AMD 2 2014 | JUNCTION BOXES FOR PHOTOVOLTAIC MODULES |
| EN 61076-4-100:2001 | Connectors for electronic equipment - Part 4-100: Printed board connectors with assessed quality - Detail specification for two-part connector modules having a grid of 2,5 mm for printed boards and backplanes |
| EN 61243-5:2001 | Live working - Voltage detectors - Part 5: Voltage detecting systems (VDS) |
| EN 61076-4-115:2003 | Connectors for electronic equipment - Part 4-115: Printed board connectors - Backplane connector for InfiniBand equipment |
| EN 50521:2008/A1:2012 | CONNECTORS FOR PHOTOVOLTAIC SYSTEMS - SAFETY REQUIREMENTS AND TESTS |
| EN 61984:2009 | Connectors - Safety requirements and tests |
| EN 61076-4-107:2001 | Connectors for electronic equipment - Part 4-107: Printed board connectors with assessed quality - Detail specification for shielded two-part connectors having a basic grid of 2,0 mm, fixed part with solder and press-in terminations for printed boards, free part with non-accessible insulation displacement and crimp terminations |
| EN 61076-4-111:2002 | Connectors for electronic equipment - Part 4-111: Printed board connectors with assessed quality - Detail specification for two-part power connector modules, for printed boards and backplanes having early mating features, and having a basic grid of 2,5 mm in accordance with IEC 60917-1 |
| EN 60352-1:1997 | Solderless connections - Part 1: Wrapped connections - General requirements, test methods and practical guidance |
| EN 50467:2011 | RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS |
| EN 50343 : 2014 AMD 1 2017 | RAILWAY APPLICATIONS - ROLLING STOCK - RULES FOR INSTALLATION OF CABLING |
| EN 61076-4-104:1999 | Connectors for use in d.c. low-frequency analogue and digital high speed data applications - Part 4-104: Printed board connectors with assessed quality - Detail specification for two-part modular connectors, basic grid of 2,0 mm, with terminations on a multiple grid of 0,5 mm |
| EN 60947-7-4 : 2013 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 7-4: ANCILLARY EQUIPMENT - PCB TERMINAL BLOCKS FOR COPPER CONDUCTORS (IEC 60947-7-4:2013) |
| IEC GUIDE 109:2012 | Environmental aspects - Inclusion in electrotechnical product standards |
| IEC 60068-1:2013 | Environmental testing - Part 1: General and guidance |
| IEC 62326-4:1996 | Printed boards - Part 4: Rigid multilayer printed boards with interlayer connections - Sectional specification |
| IEC 60352-1:1997 | Solderless connections - Part 1: Wrapped connections - General requirements, test methods and practical guidance |
| IEC 60512-1-100:2012 | Connectors for electronic equipment - Tests and measurements - Part 1-100: General - Applicable publications |
| IEC 61188-5-1:2002 | Printed boards and printed board assemblies - Design and use - Part 5-1: Attachment (land/joint) considerations - Generic requirements |
| IEC 60050-581:2008 | International Electrotechnical Vocabulary (IEV) - Part 581: Electromechanical components for electronic equipment |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.