UNI EN 12405-1 : 2010
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
GAS METERS - CONVERSION DEVICES - PART 1: VOLUME CONVERSION
Superseded date
30-07-2022
Superseded by
Published date
01-01-2010
Sorry this product is not available in your region.
Foreword
1 Scope
2 Normative references
3 Terms, definitions and symbols
4 Principle of measurement
5 Rated operating conditions
6 Construction requirements
7 Installation requirements
8 Performance
9 Tests of conformity
10 Marking
11 Installation and operating instructions
Annex A (normative) - Type test
Annex B (normative) - Pressure transducers
Annex C (normative) - Platinum resistance thermometer sensors
Annex D (normative) - Temperature transducers
Annex E (informative) - Model type test report for conversion
devices
Annex F (informative) - Model type test report for associated
transducers
Annex ZA (informative) - Relationship between this European
Standard and the Essential Requirements of EU Directive
2004/22 MeasuringInstruments Directive
Bibliography
Describes the requirements and tests for the construction, performance, safety and conformity of gas-volume electronic conversion devices associated to gas meters, used to measure volumes of fuel gases of the 1st and 2nd families according to EN 437.
| DocumentType |
Standard
|
| PublisherName |
Ente Nazionale Italiano di Unificazione (UNI)
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| NF EN 12405-1 : 2005 + A2 2010 | Identical |
| EN 12405-1:2005+A2:2010 | Identical |
| UNE-EN 12405-1:2006 | Identical |
| BS EN 12405-1 : 2005 | Identical |
| NS EN 12405-1 : 2005 + A2 2010 | Identical |
| NBN EN 12405-1 : 2005 + A2 2010 | Identical |
| SN EN 12405-1 : 2005 + A2 2011 | Identical |
| DIN EN 12405-1:2011-04 | Identical |
| ONORM EN 12405-1 : 2011 | Identical |
| I.S. EN 12405-1:2005 | Identical |
| NEN EN 12405-1 : 2005 + A2 2010 | Identical |
| UNI 9167 : 2009 | INITIAL PRESSURE AND REDUCTION PLANTS FOR NATURAL GAS - DESIGN, CONSTRUCTION AND TESTING |
| UNI/TS 11291-2 : 2010 | GAS MEASUREMENT SYSTEMS - HOURLY BASED GAS METERING SYSTEMS - PART 2: CTE PROTOCOL |
| UNI/TS 11291-6 : 2013 | GAS MEASUREMENT SYSTEMS - HOURLY BASED GAS METERING SYSTEMS - PART 6: REQUIREMENTS FOR METERS LESS THAN 10 M[3]/H (LESS THAN GROUP G10) |
| UNI/TS 11291-5 : 2013 | GAS MEASUREMENT SYSTEMS - HOURLY BASED GAS METERING SYSTEMS - PART 5: REQUIREMENTS FOR METERS WITH CAPACITY FROM 16 M[3]/H UP TO 65 M[3]/H (GROUP FROM G10 UP TO G40) |
| UNI 10619-3 : 2014 | GAS PRESSURE CONTROL SYSTEMS AND/OR GAS MEASUREMENT INSTALLATIONS FOR INLET MAX PRESSURE UP TO 12 BAR FOR INDUSTRIAL AND DOMESTIC USE - PART 3: DESIGN, CONSTRUCTION AND TESTING - GAS MEASUREMENT INSTALLATIONS |
| UNI 10619-1 : 2014 | GAS PRESSURE CONTROL SYSTEMS AND/OR GAS MEASUREMENT INSTALLATIONS FOR INLET MAX PRESSURE UP TO 12 BAR FOR INDUSTRIAL AND DOMESTIC USE - PART 1: DESIGN, CONSTRUCTION AND TESTING - GENERAL |
| UNI/TS 11291-9 : 2013 | GAS MEASUREMENT SYSTEMS - HOURLY BASED GAS METERING SYSTEMS - PART 9: FUNCTIONAL TEST AND INTEROPERABILITY TEST |
| UNI/TS 11291-4 : 2013 | GAS MEASUREMENT SYSTEMS - HOURLY BASED GAS METERING SYSTEMS - PART 4: REQUIREMENTS FOR METERS WITH CAPACITY MORE THAN 65 M[3]/H (GROUP G40) |
| UNI TS 11291-1 : 2013 | GAS MEASUREMENT SYSTEMS - HOURLY BASED GAS METERING SYSTEMS - PART 1: GENERAL REQUIREMENTS FOR REMOTE READING OR REMOTE MANAGEMENT SYSTEM |
| UNI/TS 11291-3 : 2014 | GAS MEASUREMENT SYSTEMS - HOURLY BASED GAS METERING SYSTEMS - PART 3: CTR PROTOCOL |
| IEC 60950-1:2005+AMD1:2009+AMD2:2013 CSV | Information technology equipment - Safety - Part 1: General requirements |
| IEC 60079-1:2014 RLV | Explosive atmospheres - Part 1: Equipment protection by flameproof enclosures "d" |
| EN 50160 : 2010 AMD 1 2015 | VOLTAGE CHARACTERISTICS OF ELECTRICITY SUPPLIED BY PUBLIC ELECTRICITY NETWORKS |
| EN 61000-4-1:2007 | Electromagnetic compatibility (EMC) - Part 4-1: Testing and measurement techniques - Overview of IEC 61000-4 series |
| OIML D 11 : 2013 | GENERAL REQUIREMENTS FOR MEASURING INSTRUMENTS - ENVIRONMENTAL CONDITIONS |
| EN 60079-1:2014 | Explosive atmospheres - Part 1: Equipment protection by flameproof enclosures "d" |
| IEC 61000-4-1:2006 | Electromagnetic compatibility (EMC) - Part 4-1: Testing and measurement techniques - Overview of IEC 61000-4 series |
| EN 61000-4-11:2004/A1:2017 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-11: TESTING AND MEASUREMENT TECHNIQUES - VOLTAGE DIPS, SHORT INTERRUPTIONS AND VOLTAGE VARIATIONS IMMUNITY TESTS (IEC 61000-4-11:2004/A1:2017) |
| EN 60068-2-1:2007 | Environmental testing - Part 2-1: Tests - Test A: Cold |
| EN 60079-0:2012/A11:2013 | EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS (IEC 60079-0:2011, MODIFIED) |
| EN 60068-2-2:2007 | Environmental testing - Part 2-2: Tests - Test B: Dry heat |
| IEC 61000-4-11:2004+AMD1:2017 CSV | Electromagnetic compatibility (EMC) - Part 4-11: Testing and measurement techniques - Voltage dips, short interruptions and voltage variations immunity tests |
| EN 24006:1993 | Measurement of fluid flow in closed conduits - Vocabulary and symbols (ISO 4006:1991) |
| EN 60950-1:2006/A2:2013 | INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60950-1:2005/A2:2013, MODIFIED) |
| IEC 61000-4-8:2009 | Electromagnetic compatibility (EMC) - Part 4-8: Testing and measurement techniques - Power frequency magnetic field immunity test |
| ISO 12213-3:2006 | Natural gas Calculation of compression factor Part 3: Calculation using physical properties |
| IEC 61000-4-4:2012 RLV | Electromagnetic compatibility (EMC) - Part 4-4: Testing and measurement techniques - Electrical fast transient/burst immunity test |
| EN 61000-4-2:2009 | Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity test |
| EN 60079-6:2015 | Explosive atmospheres - Part 6: Equipment protection by liquid immersion "o" |
| IEC 60068-2-31:2008 | Environmental testing - Part 2-31: Tests - Test Ec: Rough handling shocks, primarily for equipment-type specimens |
| IEC 60079-5:2015 RLV | Explosive atmospheres - Part 5: Equipment protection by powder filling "q" |
| IEC 61000-4-6:2013 | Electromagnetic compatibility (EMC) - Part 4-6: Testing and measurement techniques - Immunity to conducted disturbances, induced by radio-frequency fields |
| EN 61000-4-3 : 2006 AMD 2 2010 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-3: TESTING AND MEASUREMENT TECHNIQUES - RADIATED, RADIO-FREQUENCY, ELECTROMAGNETIC FIELD IMMUNITY TEST |
| EN 60079-11:2012 | Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i" |
| IEC 60079-11:2011 | Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i" |
| EN 437:2003+A1:2009 | Test gases - Test pressures - Appliance categories |
| EN 60751:2008 | INDUSTRIAL PLATINUM RESISTANCE THERMOMETERS AND PLATINUM TEMPERATURE SENSORS |
| EN 60079-25:2010/AC:2013 | EXPLOSIVE ATMOSPHERES - PART 25: INTRINSICALLY SAFE ELECTRICAL SYSTEMS (IEC 60079-25:2010) |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| EN 61000-4-8:2010 | Electromagnetic compatibility (EMC) - Part 4-8: Testing and measurement techniques - Power frequency magnetic field immunity test |
| EN 22768-1:1993 | General tolerances - Part 1: Tolerances for linear and angular dimensions without individual tolerance indications (ISO 2768-1:1989) |
| EN ISO 12213-3:2009 | Natural gas - Calculation of compression factor - Part 3: Calculation using physical properties (ISO 12213-3:2006) |
| IEC 60068-2-2:2007 | Environmental testing - Part 2-2: Tests - Test B: Dry heat |
| IEC 61000-4-2:2008 | Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity test |
| IEC 61000-4-3:2006+AMD1:2007+AMD2:2010 CSV | Electromagnetic compatibility (EMC) - Part 4-3: Testing and measurement techniques - Radiated, radio-frequency, electromagnetic field immunity test |
| IEC 60079-25:2010 | Explosive atmospheres - Part 25: Intrinsically safe electrical systems |
| IEC 60079-6:2015 | Explosive atmospheres - Part 6: Equipment protection by liquid immersion "o" |
| IEC 60079-0:2011 | Explosive atmospheres - Part 0: Equipment - General requirements |
| IEC 60751:2008 | Industrial platinum resistance thermometers and platinum temperature sensors |
| EN 1359:2017 | Gas meters - Diaphragm gas meters |
| EN 60068-2-78:2013 | Environmental testing - Part 2-78: Tests - Test Cab: Damp heat, steady state |
| EN 61000-4-4:2012 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-4: TESTING AND MEASUREMENT TECHNIQUES - ELECTRICAL FAST TRANSIENT/BURST IMMUNITY TEST (IEC 61000-4-4:2012) |
| EN 60079-5:2015 | Explosive atmospheres - Part 5: Equipment protection by powder filling "q" |
| CISPR 11:2015 RLV | Industrial, scientific and medical equipment - Radio-frequency disturbance characteristics - Limits and methods of measurement |
| IEC 60068-2-1:2007 | Environmental testing - Part 2-1: Tests - Test A: Cold |
| EN 61000-4-6:2014/AC:2015 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-6: TESTING AND MEASUREMENT TECHNIQUES - IMMUNITY TO CONDUCTED DISTURBANCES, INDUCED BY RADIO-FREQUENCY FIELDS (IEC 61000-4-6:2013) |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| EN 60068-2-30:2005 | Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle) |
| EN ISO 12213-2:2009 | Natural gas - Calculation of compression factor - Part 2: Calculation using molar-composition analysis (ISO 12213-2:2006) |
| ISO 12213-2:2006 | Natural gas Calculation of compression factor Part 2: Calculation using molar-composition analysis |
| IEC 61000-4-29:2000 | Electromagnetic compatibility (EMC) - Part 4-29: Testing and measurement techniques - Voltage dips, short interruptions and voltage variations on d.c. input power port immunity tests |
| ISO 4006:1991 | Measurement of fluid flow in closed conduits — Vocabulary and symbols |
| EN 61000-4-29:2000 | Electromagnetic compatibility (EMC) - Part 4-29: Testing and measurement techniques - Voltage dips, short interruptions and voltage variations on d.c. input power port immunity tests |
| EN 60730-1:2016 | Automatic electrical controls - Part 1: General requirements |
| EN 1776:2015 | Gas infrastructure - Gas measuring systems - Functional requirements |
| EN 60068-2-31:2008 | ENVIRONMENTAL TESTING - PART 2-31: TESTS - TEST EC: ROUGH HANDLING SHOCKS, PRIMARILY FOR EQUIPMENT-TYPE SPECIMENS |
| IEC 60730-1:2013+AMD1:2015 CSV | Automatic electrical controls - Part 1: General requirements |
| EN 60079-2:2014/AC:2015 | EXPLOSIVE ATMOSPHERES - PART 2: EQUIPMENT PROTECTION BY PRESSURIZED ENCLOSURE 'P' (IEC 60079-2:2014) |
| IEC 60068-2-30:2005 | Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.