ASTM D 638 : 2014
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Tensile Properties of Plastics
Available format(s)
Hardcopy , PDF
Superseded date
25-07-2022
Superseded by
Language(s)
English
Published date
12-03-2015
Important note : Users cannot be edited or removed once added to your Multi user PDF.This test method covers the determination of the tensile properties of unreinforced and reinforced plastics in the form of standard dumbbell-shaped test specimens when tested under defined conditions of pretreatment, temperature, humidity, and testing machine speed.
| Committee |
D 20
|
| DocumentType |
Test Method
|
| Pages |
17
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method covers the determination of the tensile properties of unreinforced and reinforced plastics in the form of standard dumbbell-shaped test specimens when tested under defined conditions of pretreatment, temperature, humidity, and testing machine speed.
1.2This test method is applicable for testing materials of any thickness up to 14 mm (0.55 in.). However, for testing specimens in the form of thin sheeting, including film less than 1.0 mm (0.04 in.) in thickness, ASTM standard D882 is the preferred test method. Materials with a thickness greater than 14 mm (0.55 in.) shall be reduced by machining.
1.3This test method includes the option of determining Poisson's ratio at room temperature.
Note 1:This standard and ISO 527-1 address the same subject matter, but differ in technical content.
Note 2:This test method is not intended to cover precise physical procedures. It is recognized that the constant rate of crosshead movement type of test leaves much to be desired from a theoretical standpoint, that wide differences may exist between rate of crosshead movement and rate of strain between gage marks on the specimen, and that the testing speeds specified disguise important effects characteristic of materials in the plastic state. Further, it is realized that variations in the thicknesses of test specimens, which are permitted by these procedures, produce variations in the surface-volume ratios of such specimens, and that these variations may influence the test results. Hence, where directly comparable results are desired, all samples should be of equal thickness. Special additional tests should be used where more precise physical data are needed.
Note 3:This test method may be used for testing phenolic molded resin or laminated materials. However, where these materials are used as electrical insulation, such materials should be tested in accordance with Test Methods D229 and Test Method D651.
Note 4:For tensile properties of resin-matrix composites reinforced with oriented continuous or discontinuous high modulus >20-GPa (>3.0 × 106-psi) fibers, tests shall be made in accordance with Test Method D3039/D3039M.
1.4Test data obtained by this test method have been found to be useful in engineering design. However, it is important to consider the precautions and limitations of this method found in Note 2 and Section 4 before considering these data for engineering design.
1.5The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.
1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM F 3373 : 2021 | Standard Specification for Polyethylene (PE) Electrofusion Fittings for Outside Diameter Controlled Crosslinked Polyethylene (PEX) Pipe |
| ASTM D 3935 : 2021 | Standard Classification System and Basis for Specification for Polycarbonate (PC) Unfilled and Reinforced Material |
| ASTM F 2225 : 2015 : R2020 | Standard Safety Specification for Consumer Trampoline Enclosures |
| ASTM F 1804 : 2021 | Standard Practice for Determining Allowable Tensile Load for Polyethylene (PE) Gas Pipe During Pull-In Installation |
| ASTM D 5592 : 1994 : R2018 | Standard Guide for Material Properties Needed in Engineering Design Using Plastics |
| ASTM D 2239 : 2021 | Standard Specification for Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter |
| ASTM D 4634 : 2016 | Standard Classification System and Basis for Specification for Styrene-Maleic Anhydride Molding and Extrusion Materials (S/MA) |
| ASTM F 1743 : 2021 | Standard Practice for Rehabilitation of Existing Pipelines and Conduits by Pulled-in-Place Installation of Cured-in-Place Thermosetting Resin Pipe (CIPP) |
| ASTM C 1173 : 2022 | Standard Specification for Flexible Transition Couplings for Underground Piping Systems |
| ASTM F 1871 : 2020 | Standard Specification for Folded/Formed Poly (Vinyl Chloride) Pipe Type A for Existing Sewer and Conduit Rehabilitation |
| ASTM D 2287 : 2019 | Standard Classification System and Basis for Specification for Nonrigid Vinyl Chloride Polymer and Copolymer Molding and Extrusion Compounds |
| ASTM F 3034 : 2021 | Standard Specification for Billets made by Winding Molten Extruded Stress-Rated High Density Polyethylene (HDPE) |
| ASTM D 3159 : 2022 | Standard Specification for Modified ETFE Fluoropolymer Molding and Extrusion Materials |
| ASTM D 706 : 2020 | Standard Classification System and Basis for Specifications for Cellulose Acetate Molding and Extrusion Compounds (CA) |
| ASTM D 5364 : 2014 : R2019 | Standard Guide for Design, Fabrication, and Erection of Fiberglass Reinforced (FRP) Plastic Chimney Liners with Coal-Fired Units |
| ASTM D 4802 : 2016 | Standard Specification for Poly(Methyl Methacrylate) Acrylic Plastic Sheet |
| ASTM D 4895 : 2018 | Standard Specification for Polytetrafluoroethylene (PTFE) Resin Produced From Dispersion |
| ASTM F 3219 : 2019 | Standard Specification for 3 to 30 in. (75 To 750 mm) Polypropylene (PP) Corrugated Single Wall Pipe and Fittings |
| ASTM F 2418 : 2019 | Standard Specification for Polypropylene (PP) Corrugated Wall Stormwater Collection Chambers |
| ASTM F 2971 : 2013 : R2021 | Standard Practice for Reporting Data for Test Specimens Prepared by Additive Manufacturing |
| ASTM E 2254 : 2018 | Standard Test Method for Storage Modulus Calibration of Dynamic Mechanical Analyzers |
| ASTM D 5045 : 2014 | Standard Test Methods for Plane-Strain Fracture Toughness and Strain Energy Release Rate of Plastic Materials |
| ASTM D 6098 : 2016 | Standard Classification System and Basis for Specification for Extruded and Compression Molded Shapes Made from Polycarbonate (PC) |
| ASTM D 3032 : 2021 : REV A | Standard Test Methods for Hookup Wire Insulation |
| ASTM D 2513 : 2020 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2609 : 2021 | Standard Specification for Plastic Insert Fittings for Polyethylene (PE) Plastic Pipe |
| ASTM F 3536 : 2022 | Standard Specification for PE and PP Mechanical Fittings for use on NPS 3 or Smaller Cold-water Service Polyethylene (PE) or Crosslinked Polyethylene (PEX) Pipe or Tubing |
| ASTM D 5083 : 2017 | Standard Test Method for Tensile Properties of Reinforced Thermosetting Plastics Using Straight-Sided Specimens |
| ASTM D 6392 : 2012 : R2018 | Standard Test Method for Determining the Integrity of Nonreinforced Geomembrane Seams Produced Using Thermo-Fusion Methods |
| ASTM F 2767 : 2018 | Standard Specification for Electrofusion Type Polyamide-12 Fittings for Outside Diameter Controlled Polyamide-12 Pipe and Tubing for Gas Distribution |
| ASTM D 3105 : 2017 | Standard Index of Methods for Testing Elastomeric and Plastomeric Roofing and Waterproofing Materials |
| ASTM F 1635 : 2016 | Standard Test Method for <emph type="bdit">in vitro</emph> Degradation Testing of Hydrolytically Degradable Polymer Resins and Fabricated Forms for Surgical Implants |
| ASTM D 5336 : 2021 | Standard Classification System and Basis for Specification for Polyphthalamide (PPA) Injection Molding Materials |
| ASTM D 4549 : 2015 : R2021 | Standard Classification System and Basis for Specification for Polystyrene and Rubber-Modified Polystyrene Molding and Extrusion Materials (PS) |
| ASTM F 2026 : 2017 | Standard Specification for Polyetheretherketone (PEEK) Polymers for Surgical Implant Applications |
| ASTM F 790 : 2018 | Standard Guide for Testing Materials for Aerospace Plastic Transparent Enclosures |
| ASTM D 5948 : 2005 : R2020 | Standard Specification for Molding Compounds, Thermosetting |
| ASTM D 4000 : 2020 | Standard Classification System for Specifying Plastic Materials |
| ASTM F 2759 : 2019 | Standard Guide for Assessment of the Ultra-High Molecular Weight Polyethylene (UHMWPE) Used in Orthopedic and Spinal Devices |
| ASTM D 1562 : 2015 | Standard Classification System and Basis for Specification for Cellulose Acetate Propionate Molding and Extrusion Compounds (CAP) |
| ASTM F 2176 : 2017 | Standard Specification for Mechanical Couplings Used on Polyethylene Conduit, Duct and Innerduct (Withdrawn 2024) |
| ASTM D 1623 : 2017 | Standard Test Method for Tensile and Tensile Adhesion Properties of Rigid Cellular Plastics |
| ASTM D 4396 : 2015 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds for Plastic Pipe and Fittings Used in Nonpressure Applications |
| ASTM F 3333 : 2020 | Standard Specification for Chopped Carbon Fiber Reinforced (CFR) Polyetheretherketone (PEEK) Polymers for Surgical Implant Applications |
| ASTM F 3508 : 2021 : REV A | Standard Guide for In-Situ Pipeline Renovation As Dual-Wall Composite Pipeline by Push/Pull Installation of Compressed-Fit Shape-Memory-Polymer Tubular (SMPT) |
| ASTM D 3517 : 2019 | Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pressure Pipe |
| ASTM F 2921 : 2013 : R2019 | Standard Terminology for Additive Manufacturing—Coordinate Systems and Test Methodologies |
| ASTM F 1588 : 1996(R2019) | Standard Test Method for Constant Tensile Load Joint Test (CTLJT) |
| ASTM F 2817 : 2013 : R2019 | Standard Specification for Poly (Vinyl Chloride) (PVC) Gas Pressure Pipe and Fittings For Maintenance or Repair |
| ASTM D 7745 : 2019 | Standard Practice for Testing Pultruded Composites |
| ASTM D 6394 : 2021 : REV A | Standard Classification System for and Basis for Specification for Sulfone Plastics (SP) |
| ASTM D 3748 : 2014 : R2019 | Standard Practice for Evaluating High-Density Rigid Cellular Plastics |
| ASTM G 178 : 2016 | Standard Practice for Determining the Activation Spectrum of a Material (Wavelength Sensitivity to an Exposure Source) Using the Sharp Cut-On Filter or Spectrographic Technique |
| ASTM F 1988 : 1999(R2020) | Standard Performance Requirements for Plastic Chaise Lounges, With or Without Moving Arms, With Adjustable Backs, for Outdoor Use |
| ASTM D 7292 : 2018 | Standard Specification for Extruded, Compression-Molded, and Injection-Molded Basic Shapes of Polyamide-Imide (PAI) |
| ASTM F 1563 : 2001 : R2019 | Standard Specification for Tools to Squeeze-off Polyethylene (PE) Gas Pipe or Tubing |
| ASTM F 381 : 2016 | Standard Safety Specification for Components, Assembly, Use, and Labeling of Consumer Trampolines |
| ASTM D 3308 : 2012 : R2022 | Standard Specification for PTFE Resin Skived Tape |
| ASTM D 6263 : 2022 | Standard Specification for Extruded Rods and Bars Made From Rigid Poly(Vinyl Chloride) (PVC) and Chlorinated Poly(Vinyl Chloride) (CPVC) |
| ASTM F 2435 : 2022 | Standard Specification for Steel Reinforced Polyethylene (PE) Corrugated Pipe |
| ASTM D 1039 : 2016 : R2022 | Standard Test Methods for Glass-Bonded Mica Used as Electrical Insulation |
| ASTM F 2376 : 2022 | Standard Practice for Classification, Design, Manufacture, Construction, and Operation of Water Slide Systems |
| ASTM D 4216 : 2022 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) and Related PVC and Chlorinated Poly(Vinyl Chloride) (CPVC) Building Products Compounds |
| ASTM F 2160 : 2022 | Standard Specification for Solid Wall High Density Polyethylene (HDPE) Conduit Based on Controlled Outside Diameter (OD) |
| ASTM D 2996 : 2017 | Standard Specification for Filament-Wound “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe |
| ASTM D 7272 : 2006 : R2018 | Standard Test Method for Determining the Integrity of Seams Used in Joining Geomembranes by Premanufactured Taped Methods |
| ASTM F 2945 : 2018 | Standard Specification for Polyamide 11 Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 3965 : 2021 | Standard Classification System and Basis for Specifications for Rigid Acrylonitrile-Butadiene-Styrene (ABS) Materials for Pipe and Fittings |
| ASTM D 4673 : 2016 | Standard Classification System for and Basis for Specification for Acrylonitrile–Butadiene–Styrene (ABS) Plastics and Alloys Molding and Extrusion Materials |
| ASTM D 3275 : 2018 | Standard Classification System for E-CTFE-Fluoroplastic Molding, Extrusion, and Coating Materials |
| ASTM D 4976 : 2012 : REV A : R2020 | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials |
| ASTM A 1113/A1113M : 2020 : EDT 1 | Standard Specification for Corrugated Steel Structural Plate, Polymer-Coated, for Field-Bolted Pipe, Pipe-Arches, and Arches |
| ASTM F 561 : 2019 | Standard Practice for Retrieval and Analysis of Medical Devices, and Associated Tissues and Fluids |
| ASTM D 6272 : 2017 : EDT 1 | Standard Test Method for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials by Four-Point Bending |
| ASTM F 2619/F2619M : 2020 | Standard Specification for High-Density Polyethylene (PE) Line Pipe |
| ASTM F 2790 : 2010 : R2019 : EDT 1 | Standard Practice for Static and Dynamic Characterization of Motion Preserving Lumbar Total Facet Prostheses |
| ASTM D 7408 : 2012 : R2020 | Standard Specification for Non-Reinforced PVC (Polyvinyl Chloride) Geomembrane Seams |
| ASTM D 3841 : 2021 | Standard Specification for Glass-Fiber-Reinforced Polyester Plastic Panels |
| ASTM C 881/C881M : 2020 : REV A | Standard Specification for Epoxy-Resin-Base Bonding Systems for Concrete |
| ASTM D 6262 : 2017 | Standard Specification for Extruded, Compression Molded, and Injection Molded Basic Shapes of Poly(aryl ether ketone) (PAEK) |
| ASTM E 2831/E2831M : 2011 : R2018 | Standard Guide for Deployment of Blast Resistant Trash Receptacles in Crowded Places |
| ASTM D 4762 : 2018 | Standard Guide for Testing Polymer Matrix Composite Materials |
| ASTM F 639 : 2009 : R2015 | Standard Specification for Polyethylene Plastics for Medical Applications |
| ASTM D 6712 : 2017 | Standard Specification for Ultra-High-Molecular-Weight Polyethylene (UHMW-PE) Solid Plastic Shapes |
| ASTM F 2928 : 2018 | Standard Practice for Specimens and Testing Conditions for Testing Polyethylene (PE) Pipe Butt Fusions Using Tensile and Hydrostatic Test Methods |
| ASTM D 3916 : 2008 : R2016 | Standard Test Method for Tensile Properties of Pultruded Glass-Fiber-Reinforced<brk /> Plastic Rod |
| ASTM D 5224 : 2012 : R2019 | Standard Practice for Compression Molding Test Specimens of Thermosetting Molding Compounds |
| ASTM D 6338 : 2017 | Standard Classification System for Highly Crosslinked Thermoplastic Vulcanizates (HCTPV) Based on ASTM Standard Test Methods |
| ASTM D 5138 : 2016 | Standard Classification System and Basis for Specification for Liquid Crystal Polymers Molding and Extrusion Materials (LCP) |
| ASTM F 2097 : 2020 | Standard Guide for Design and Evaluation of Primary Flexible Packaging for Medical Products |
| ASTM F 451 : 2021 | Standard Specification for Acrylic Bone Cement |
| ASTM F 711 : 2017 | Standard Specification for Fiberglass-Reinforced Plastic (FRP) Rod and Tube Used in Live Line Tools |
| ASTM D 4801 : 2008 : R2016 | Standard Specification for Polyethylene Sheeting in Thickness of 0.25 mm (0.010 in.) and Greater |
| ASTM D 3754 : 2019 | Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Sewer and Industrial Pressure Pipe |
| ASTM F 1533 : 2020 | Standard Specification for Deformed Polyethylene (PE) Liner |
| ASTM F 852/F852M : 2022 | Standard Specification for Portable Gasoline, Kerosene, and Diesel Containers for Consumer Use |
| ASTM D 2902 : 2021 | Standard Specification for Fluoropolymer Resin Heat-Shrinkable Tubing for Electrical Insulation |
| ASTM F 1858 : 1998 : R2020 | Standard Performance Requirements for Multipositional Plastic Chairs with Adjustable Backs or Reclining Mechanisms for Outdoor Use |
| ASTM F 3087 : 2015 | Standard Specification for Acrylic Molding Resins for Medical Implant Applications |
| ASTM F 2562/F2562M : 2015 : R2019 | Specification for Steel Reinforced Thermoplastic Ribbed Pipe and Fittings for Non-Pressure Drainage and Sewerage |
| ASTM D 8366 : 2021 : REV A | Standard Specification for Extruded and Compression Molded Shapes Made from Unfilled Poly(Vinylidene Fluoride) PVDF |
| ASTM D 5436 : 2015 : R2020 | Standard Specification for Cast Poly(Methyl Methacrylate) Plastic Rods, Tubes, and Shapes |
| ASTM D 8033 : 2016 | Standard Classification System for Poly(Ether Ether Ketone) (PEEK) Molding and Extrusion Materials |
| ASTM F 2896 : 2011 : R2017 | Standard Specification for Reinforced Polyethylene Composite Pipe For The Transport Of Oil And Gas And Hazardous Liquids |
| ASTM D 6456 : 2010 : R2018 | Standard Specification for Finished Parts Made from Polyimide Resin |
| ASTM F 3524/F3524M : 2021 | Standard Specification for Polyamide-12 (PA12) Line Pipe |
| ASTM D 3368 : 2017 : R2022 | Standard Specification for FEP Sheet and Film |
| ASTM D 1822 : 2021 | Standard Test Method for Determining the Tensile-Impact Resistance of Plastics |
| ASTM F 1924 : 2019 | Standard Specification for Plastic Mechanical Fittings for Use on Outside Diameter Controlled Polyethylene Gas Distribution Pipe and Tubing |
| ASTM F 480 : 2014 : R2022 | Standard Specification for Thermoplastic Well Casing Pipe and Couplings Made in Standard Dimension Ratios (SDR), SCH 40 and SCH 80 |
| ASTM D 3262 : 2020 | Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Sewer Pipe |
| ASTM F 2600 : 2009 : R2018 | Standard Specification for Electrofusion Type Polyamide-11 Fittings for Outside Diameter Controlled Polyamide-11 Pipe and Tubing |
| ASTM G 210 : 2013 : R2018 | Standard Practice for Operating the Severe Wastewater Analysis Testing Apparatus |
| ASTM F 1867 : 2006 : R2020 | Standard Practice for Installation of Folded/Formed Poly (Vinyl Chloride) (PVC) Pipe Type A for Existing Sewer and Conduit Rehabilitation |
| ASTM F 3525/F3525M : 2021 | Standard Specification Fabricated Fittings of Crosslinkable Polyethylene (CX-PE) |
| ASTM F 1606 : 2019 | Standard Practice for Rehabilitation of Existing Sewers and Conduits with Deformed Polyethylene (PE) Liner |
| ASTM D 6324 : 2011 : R2017 | Standard Specification for Male Condoms Made from Polyurethane |
| ASTM F 641 : 2009 : R2014 | Standard Specification for Implantable Epoxy Electronic Encapsulants |
| ASTM D 4067 : 2021 | Standard Classification System and Basis for Specification for Reinforced and Filled Poly(Phenylene Sulfide) (PPS) Injection Molding and Extrusion Materials Using ASTM Methods |
| ASTM D 5205 : 2016 | Standard Classification System and Basis for Specification for Polyetherimide (PEI) Materials |
| ASTM D 2122 : 2016 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 4097 : 2019 | Standard Specification for Contact-Molded Glass-Fiber-Reinforced Thermoset Resin Corrosion-Resistant Tanks |
| ASTM D 787 : 2018 | Standard Specification for Ethyl Cellulose Molding and Extrusion Compounds |
| ASTM F 3378/F3378M : 2022 | Standard Specification for Crosslinkable Polyethylene (CX-PE) Pipe |
| ASTM D 6041 : 2018 | Standard Specification for Contact-Molded “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Corrosion Resistant Pipe and Fittings |
| ASTM F 702 : 2018 | Standard Specification for Polysulfone Resin for Medical Applications |
| ASTM E 2771 : 2011 : R2019 | Standard Terminology for Homeland Security Applications |
| ASTM C 722 : 2018 | Standard Specification for Chemical-Resistant Monolithic Floor Surfacings |
| ASTM D 695 : 2015 | Standard Test Method for Compressive Properties of Rigid Plastics |
| ASTM F 2509 : 2015 : R2019 | Standard Specification for Field-assembled Anodeless Riser Kits for Use on Outside Diameter Controlled Polyethylene and Polyamide-11 (PA11) Gas Distribution Pipe and Tubing |
| ASTM D 4101 : 2017 : EDT 1 | Standard Classification System and Basis for Specification for Polypropylene Injection and Extrusion Materials |
| ASTM F 3507 : 2021 | Standard Practice for Butt-Fusion Joining of Crosslinkable Polyethylene (CX-PE) Pipe and Tubing |
| ASTM D 3222 : 2021 | Standard Specification for Unmodified Poly(Vinylidene Fluoride) (PVDF) Molding Extrusion and Coating Materials |
| ASTM D 2647 : 2018 | Standard Specification for Crosslinkable Ethylene Plastics |
| ASTM D 3295 : 2020 | Standard Specification for PTFE Tubing, Miniature Beading and Spiral Cut Tubing |
| ASTM D 2633 : 2021 | Standard Test Methods for Thermoplastic Insulations and Jackets for Wire and Cable |
| ASTM D 7056 : 2007 : R2018 | Standard Test Method for Determining the Tensile Shear Strength of Prefabricated Bituminous Geomembrane Seams |
| ASTM F 3181 : 2016 | Standard Test Method for The Un-notched, Constant Ligament Stress Crack Test (UCLS) for HDPE Materials Containing Post- Consumer Recycled HDPE |
| ASTM F 1055 : 2016 : REV A | Standard Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene and Crosslinked Polyethylene (PEX) Pipe and Tubing |
| ASTM D 3307 : 2021 | Standard Specification for Perfluoroalkoxy (PFA) Resin Molding and Extrusion Materials |
| ASTM D 1043 : 2016 | Standard Test Method for Stiffness Properties of Plastics as a Function of Temperature by Means of a Torsion Test |
| ASTM F 2902 : 2016 : EDT 1 | Standard Guide for Assessment of Absorbable Polymeric Implants |
| ASTM C 1594 : 2011 : R2017 | Standard Specification for Polyimide Rigid Cellular Thermal Insulation |
| ASTM D 3013 : 2013 : R2021 | Standard Specification for Epoxy Molding Compounds |
| ASTM D 6713 : 2021 | Standard Specification for Extruded and Compression Molded Shapes Made from Poly(Vinylidene Fluoride) (PVDF) |
| ASTM F 2145 : 2013 : R2018 | Standard Specification for Polyamide 11 (PA 11) and Polyamide 12 (PA12) Mechanical Fittings for Use on Outside Diameter Controlled Polyamide 11 and Polyamide 12 Pipe and Tubing |
| ASTM D 2294 : 1996 : R2016 | Standard Test Method for Creep Properties of Adhesives in Shear by Tension Loading (Metal-to-Metal) |
| ASTM F 450 : 2013 : R2019 | Standard Test Methods for Vacuum Cleaner Hose—Durability and Reliability (Plastic) |
| ASTM F 412 : 2021 | Standard Terminology Relating to Plastic Piping Systems |
| ASTM F 1309 : 1998 : R2018 | Standard Practice for Installation Procedures for Fitting Chocks to Marine Machinery Foundations |
| ASTM D 4093 : 1995 : R2014 | Standard Test Method for Photoelastic Measurements of Birefringence and Residual Strains in Transparent or Translucent Plastic Materials |
| ASTM D 5989 : 2018 | Standard Specification for Extruded and Monomer Cast Shapes Made from Nylon (PA) |
| ASTM F 1973 : 2021 | Standard Specification for Factory Assembled Anodeless Risers and Transition Fittings in Polyethylene (PE) and Polyamide 11 (PA11) and Polyamide 12 (PA12) Fuel Gas Distribution Systems |
| ASTM D 3485 : 2015 | Standard Specification for Coilable High Density Polyethylene (HDPE) Cable in Conduit (CIC) |
| ASTM D 4434/D4434M : 2021 | Standard Specification for Poly(Vinyl Chloride) Sheet Roofing |
| ASTM F 2820 : 2012 : R2021 : EDT 1 | Standard Specification for Polyetherketoneketone (PEKK) Polymers for Surgical Implant Applications |
| ASTM F 645 : 2018 : REV B | Standard Guide for Selection, Design, and Installation of Thermoplastic Water- Pressure Piping Systems |
| ASTM F 3183 : 2021 | Standard Practice for Guided Side Bend Evaluation of Polyethylene Pipe Butt Fusion Joint |
| ASTM F 2306/F2306M : 2021 | Standard Specification for 300 mm to 1500 mm [12 in. to 60 in.] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Non-Pressure Gravity-Flow Storm Sewer and Subsurface Drainage Applications |
| ASTM D 4565 : 2020 | Standard Test Methods for Physical and Environmental Performance Properties of <brk/>Insulations and Jackets for Telecommunications Wire and Cable |
| ASTM E 2740 : 2012 : R2018 | Standard Specification for Trash Receptacles Subjected to Blast Resistance Testing |
| ASTM D 229 : 2019 : EDT 1 | Standard Test Methods for Rigid Sheet and Plate Materials Used for Electrical Insulation |
| ASTM D 6339 : 2011 : R2019 | Standard Classification System for and Basis for Specifications for Syndiotactic Polystyrene Molding and Extrusion (SPS) |
| ASTM D 3350 : 2021 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM F 1838 : 2019 | Standard Performance Requirements for Adult and Children’s Plastic Chairs for Outdoor Use |
| ASTM F 602 : 2009 : R2015 | Standard Criteria for Implantable Thermoset Epoxy Plastics (Withdrawn 2024) |
| ASTM F 2764/F2764M : 2019 | Standard Specification for 6 to 60 in. [150 to 1500 mm] Polypropylene (PP) Corrugated Double and Triple Wall Pipe and Fittings for Non-Pressure Sanitary Sewer Applications |
| ASTM C 1349 : 2017 | Standard Specification for Architectural Flat Glass Clad Polycarbonate |
| ASTM D 7275 : 2007 : R2018 | Standard Test Method for Tensile Properties of Bituminous Geomembranes (BGMs) |
| ASTM E 2639 : 2012 : R2018 | Standard Test Method for Blast Resistance of Trash Receptacles |
| ASTM D 3840 : 2019 | Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe Fittings for Nonpressure Applications |
| ASTM D 2295 : 1996 : R2016 | Standard Test Method for Strength Properties of Adhesives in Shear by Tension Loading at Elevated Temperatures (Metal-to-Metal) |
| ASTM C 582 : 2009 : R2016 | Standard Specification for Contact-Molded Reinforced Thermosetting Plastic (RTP) Laminates for Corrosion-Resistant Equipment |
| ASTM D 7472 : 2019 | Standard Specification for EFEP-Fluoropolymer Molding and Extrusion Materials |
| ASTM F 2881/F2881M : 2021 : EDT 1 | Standard Specification for 12 to 60 in. [300 to 1500 mm] Polypropylene (PP) Dual Wall Pipe and Fittings for Non-Pressure Storm Sewer Applications |
| ASTM F 755 : 2019 | Standard Specification for Selection of Porous Polyethylene for Use in Surgical Implants |
| ASTM D 7194 : 2019 | Standard Specification for Aerospace Parts Machined from Polychlorotrifluoroethylene (PCTFE) |
| ASTM D 7027 : 2020 | Standard Test Method for Evaluation of Scratch Resistance of Polymeric Coatings and Plastics Using an Instrumented Scratch Machine |
| ASTM D 3929 : 2003 : R2015 | Standard Test Method for Evaluating Stress Cracking of Plastics by Adhesives Using the Bent-Beam Method |
| ASTM D 883 : 2020 : REV B | Standard Terminology Relating to Plastics |
| ASTM D 7082 : 2021 | Standard Specification for Polyethylene Stay In Place Form System for End Walls for Drainage Pipe |
| ASTM F 1948 : 2020 | Standard Specification for Metallic Mechanical Fittings for Use on Outside Diameter Controlled Thermoplastic Gas Distribution Pipe and Tubing |
| ASTM F 997 : 2018 | Standard Specification for Polycarbonate Resin for Medical Applications |
| ASTM D 8436 : 2022 | Standard Specification for Fluoropolymer-based Materials for Use for Encapsulation of Downhole Cable |
| ASTM D 7471 : 2019 | Standard Specification for CPT-Fluoropolymer Molding and Extrusion Materials |
| ASTM F 2720/F2720M : 2020 | Standard Specification for Glass Fiber Reinforced Polyethylene (PE-GF) Spiral Wound Large Diameter Pipe |
| ASTM A 974 : 1997 : R2021 | Standard Specification for Welded Wire Fabric Gabions and Gabion Mattresses (Metallic-Coated or Polyvinyl Chloride (PVC) Coated) |
| ASTM D 1248 : 2016 | Standard Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable |
| ASTM D 8427 : 2021 | Standard Specification for Rigid Poly Vinyl Chloride (PVC) Exterior Profiles Used for Sheet Piling |
| ASTM D 6261 : 2014 : R2022 | Standard Specification for Extruded and Compression Molded Basic Shapes Made from Thermoplastic Polyester (TPES) |
| ASTM D 790 : 2017 | Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials |
| ASTM F 2331 : 2011 : R2021 | Standard Test Method for Determining Chemical Compatibility of Substances in Contact with Thermoplastic Pipe and Fittings Materials |
| ASTM F 2785 : 2021 | Standard Specification for Polyamide 12 Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2990 : 2017 | Standard Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics |
| ASTM D 3641 : 2021 | Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials |
| ASTM D 5977 : 2015 | Standard Specification for High Load Rotational Spherical Bearings for Bridges and Structures |
| ASTM F 3091/F3091M : 2014 : R2021 | Standard Specification for Powder Bed Fusion of Plastic Materials |
| ASTM D 2105 : 2001 : R2019 | Standard Test Method for Longitudinal Tensile Properties of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Tube |
| ASTM C 1482 : 2017 | Standard Specification for Polyimide Flexible Cellular Thermal and Sound Absorbing Insulation |
| ASTM D 4020 : 2018 | Standard Specification for Ultra-High-Molecular-Weight Polyethylene Molding and Extrusion Materials |
| ASTM D 6100 : 2017 | Standard Specification for Extruded, Compression Molded and Injection Molded Polyoxymethylene Shapes (POM) |
| ASTM D 3826 : 2018 | Standard Practice for Determining Degradation End Point in Degradable Polyethylene and Polypropylene Using a Tensile Test |
| ASTM D 5747/D5747M : 2021 | Standard Practice for Tests to Evaluate the Chemical Resistance of Geomembranes to Liquids |
| ASTM C 143/C143M : 2020 | Standard Test Method for Slump of Hydraulic-Cement Concrete |
| ASTM D 5813 : 2004 : R2018 | Standard Specification for Cured-In-Place Thermosetting Resin Sewer Piping Systems |
| ASTM D 6214/D6214M : 1998 : R2022 | Standard Test Method for Determining the Integrity of Field Seams Used in Joining Geomembranes by Chemical Fusion Methods |
| ASTM F 3274 : 2021 | Standard Guide for Testing and Characterization of Alginate Foam Scaffolds Used in Tissue-Engineered Medical Products (TEMPs) |
| ASTM F 3510 : 2021 | Standard Guide for Characterizing Fiber-Based Constructs for Tissue-Engineered Medical Products |
| ASTM G 21 : 2015 : R2021 : EDT 1 | Standard Practice for Determining Resistance of Synthetic Polymeric Materials to Fungi |
| ASTM F 2947/F2947M : 2021 : REV A | Standard Specification for 150 to 1500 mm [6 to 60 in.] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications |
| ASTM D 1708 : 2018 | Standard Test Method for Tensile Properties of Plastics by Use of Microtensile Specimens |
| ASTM D 5990 : 2020 : REV A | Standard Classification System and Basis for Polyketone Injection Molding and Extrusion Materials (PK) |
| ASTM C 647 : 2019 | Standard Guide to Properties and Tests of Mastics and Coating Finishes for Thermal Insulation |
| ASTM D 5575 : 2018 | Standard Classification System for Copolymers of Vinylidene Fluoride (VDF) with Other Fluorinated Monomers |
| ASTM D 2737 : 2021 | Standard Specification for Polyethylene (PE) Plastic Tubing |
| ASTM D 6693/D6693M : 2020 | Standard Test Method for Determining Tensile Properties of Nonreinforced Polyethylene and Nonreinforced Flexible Polypropylene Geomembranes |
| ASTM E 2634 : 2018 | Standard Specification for Flat Wall Insulating Concrete Form (ICF) Systems |
| ASTM D 2116 : 2016 : R2021 | Standard Specification for FEP Resin Molding and Extrusion Materials |
| ASTM D 4203 : 2017 | Standard Specification for and Basis for Specifications for Styrene-Acrylonitrile (SAN) Injection and Extrusion Materials |
| ASTM F 648 : 2021 | Standard Specification for Ultra-High-Molecular-Weight Polyethylene Powder and Fabricated Form for Surgical Implants |
| ASTM G 114 : 2021 | Standard Practices for Evaluating the Age Resistance of Polymeric Materials Used in Oxygen Service |
| ASTM F 1216 : 2021 | Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Inversion and Curing of a Resin-Impregnated Tube |
| ASTM D 7293 : 2019 | Standard Specification for Extruded and Compression-Molded Shapes Made from Polyetherimide (PEI) |
| ASTM D 1784 : 2020 | Standard Classification System and Basis for Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds |
| ASTM F 3123 : 2022 | Standard Specification for Metric Outside Diameter Polyethylene (PE) Plastic Pipe (DR-PN) |
| ASTM F 2818 : 2010 : R2019 | Standard Specification for Specification for Crosslinked Polyethylene (PEX) Material Gas Pressure Pipe and Tubing |
| ASTM F 2150 : 2019 | Standard Guide for Characterization and Testing of Biomaterial Scaffolds Used in Regenerative Medicine and Tissue-Engineered Medical Products |
| ASTM D 5721 : 2022 | Standard Practice for Air-Oven Aging of Polyolefin Geomembranes |
| ASTM D 116 : 1986 : R2020 | Standard Test Methods for Vitrified Ceramic Materials for Electrical Applications |
| ASTM D 707 : 2015 | Standard Classification System and Basis for Specification for Cellulose Acetate Butyrate Molding and Extrusion Compounds (CAB) |
| ASTM F 1717 : 2021 | Standard Test Methods for Spinal Implant Constructs in a Vertebrectomy Model |
| FC 3-260-18F:2023 | Air Force Aircraft Arresting Systems Installation, Operation, And Maintenance, With Change 1 |
| ASTM D 4066 : 2000 | Standard Classification System for Nylon Injection and Extrusion Materials (PA) |
| ASTM D 5947 : 1996 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
| ASTM D 4000 : 2013 | Standard Classification System for Specifying Plastic Materials |
| ASTM E 1012 : 2014 | Standard Practice for Verification of Testing Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application |
| ASTM E 83 : 2000 : EDT 1 | Standard Practice for Verification and Classification of Extensometer |
| ASTM D 4000 : 2003 : REV A | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4000 : 2000 : REV A | Standard Classification System for Specifying Plastic Materials |
| ASTM D 5947 : 2002 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
| ASTM D 4066 : 2001 : REV A : R2008 | Standard Classification System for Nylon Injection and Extrusion Materials (PA) (Withdrawn 2012) |
| ASTM D 4000 : 2012 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4000 : 2009 | Standard Classification System for Specifying Plastic Materials |
| AS ISO/ASTM 52921:2020 | Standard terminology for additive manufacturing - Coordinate systems and test methodologies |
| ASTM E 83 : 1998 : EDT 1 | Standard Practice for Verification and Classification of Extensometer |
| ASTM D 4000 : 2011 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 5947 : 2011 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
| ASTM D 5947 : 2018 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
| ASTM E 691 : 2020 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM D 4066 : 2001 : REV A | Standard Classification System for Nylon Injection and Extrusion Materials (PA) |
| ASTM E 1012 : 1999 | Standard Practice for Verification of Specimen Alignment Under Tensile Loading |
| ASTM E 1012 : 2012 | Standard Practice for Verification of Testing Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application |
| ASTM D 412 : 2016 : EDT 1 | Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension |
| ASTM D 4000 : 2004 : EDT 1 | Standard Classification System for Specifying Plastic Materials |
| AS ISO/ASTM 52910:2020 | Additive manufacturing - Design - Requirements, guidelines and recommendations |
| ASTM E 1012 : 2014 : EDT 1 | Standard Practice for Verification of Testing Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application |
| ASTM E 691 : 2019 : EDT 1 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM D 4000 : 2009 : REV B | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4066 : 2013 : R2019 | Standard Classification System for Nylon Injection and Extrusion Materials (PA) |
| ASTM D 4000 : 2000 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 5947 : 2006 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
| ASTM D 4000 : 2010 : REV A | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4066 : 2001 | Standard Classification System for Nylon Injection and Extrusion Materials (PA) |
| ASTM D 412 : 2016 | Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension |
| ASTM D 4000 : 2007 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4000 : 2009 : REV A | Standard Classification System for Specifying Plastic Materials |
| ASTM E 691 : 2022 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 1012 : 2012 : EDT 1 | Standard Practice for Verification of Testing Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application |
| ASTM D 4000 : 2001 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 1822 : 2013 | Standard Test Method for Tensile-Impact Energy to Break Plastics and Electrical Insulating Materials |
| ASTM D 1822 : 2006 | Standard Test Method for Tensile-Impact Energy to Break Plastics and Electrical Insulating Materials |
| ASTM E 691 : 2009 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM D 4000 : 2008 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4066 : 1994 : REV B | Standard Classification System for Nylon Injection and Extrusion Materials (PA) |
| ASTM D 4066 : 2013 | Standard Classification System for Nylon Injection and Extrusion Materials (PA) |
| ASTM D 1822 : 1999 | Standard Test Method for Tensile-Impact Energy to Break Plastics and Electrical Insulating Materials |
| ASTM E 1012 : 2005 | Standard Practice for Verification of Test Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application |
| ASTM D 618 : 2013 | Standard Practice for Conditioning Plastics for Testing |
| ASTM E 4 : 2021 | Standard Practices for Force Calibration and Verification of Testing Machines |
| ASTM E 691 : 2021 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM D 5947 : 2003 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
| ASTM D 4000 : 2001 : REV A : EDT 1 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 1822 : 2021 | Standard Test Method for Determining the Tensile-Impact Resistance of Plastics |
| ASTM D 5947 : 2001 : EDT 1 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
| ASTM D 4000 : 2004 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 412 : 2016 : R2021 | Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension |
| ASTM D 4066 : 2000 : REV A | Standard Classification System for Nylon Injection and Extrusion Materials (PA) |
| ASTM D 4000 : 2010 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4000 : 2003 | Standard Classification System for Specifying Plastic Materials |
| ASTM E 1012 : 2019 | Standard Practice for Verification of Testing Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application |
| ASTM D 4066 : 1996 | Standard Classification System for Nylon Injection and Extrusion Materials (PA) |
| ASTM D 618 : 2021 | Standard Practice for Conditioning Plastics for Testing |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.