ISO 1514:2016
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Paints and varnishes — Standard panels for testing
Available format(s)
Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users
Superseded date
05-07-2024
Superseded by
Language(s)
English, French
Published date
18-07-2016
Important note : Users cannot be edited or removed once added to your Multi user PDF.
ISO 1514:2016 specifies several types of standard panels and describes procedures for their preparation prior to painting. These standard panels are for use in general methods of test for paints, varnishes and related products.
| Committee |
ISO/TC 35/SC 9
|
| DevelopmentNote |
Supersedes ISO/DIS 1514. (07/2016)
|
| DocumentType |
Standard
|
| Pages |
11
|
| PublisherName |
International Organization for Standardization
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes | |
| UnderRevision |
| Standards | Relationship |
| DIN EN ISO 1514:1997-09 | Identical |
| NF EN ISO 1514 : 2016 | Identical |
| NBN EN ISO 1514 : 2016 | Identical |
| NEN EN ISO 1514 : 2016 | Identical |
| NS EN ISO 1514 : 1997 | Identical |
| I.S. EN ISO 1514:2016 | Identical |
| PN EN ISO 1514 : 2016 | Identical |
| SN EN ISO 1514 : 2016 | Identical |
| UNI EN ISO 1514 : 2005 | Identical |
| UNE-EN ISO 1514:2017 | Identical |
| UNI EN ISO 1514 : 2016 | Identical |
| SS-EN ISO 1514 : 2016 | Identical |
| BS EN ISO 1514:2004 | Identical |
| EN ISO 1514:2016 | Identical |
| DIN EN ISO 1514:2005-02 | Identical |
| NS-EN ISO 1514:2016 | Identical |
| ONORM EN ISO 1514 : 2016 | Identical |
| DS EN ISO 1514 : 2016 | Identical |
| BS 3900-A3(2004) : 2004 | Identical |
| UNE-EN 605:1994 | Identical |
| DIN 53227:1978-04 | Similar to |
| I.S. EN 605:1993 | Identical |
| DIN EN 605:1992-07 | Corresponds |
| BS 3900-A3(1997) : 1997 | Identical |
| BS EN ISO 1514:2016 | Identical |
| BS 3900-A17:1986 | Methods of test for paints. Tests on liquid paints (excluding chemical tests) Coating of test panels at a specified spreading rate |
| BS 3900-F15:1995 | Methods of test for paints Determination of resistance to humidity (intermittent condensation) |
| 10/30206990 DC : 0 | BS EN ISO 6272-1 - PAINTS AND VARNISHES - RAPID-DEFORMATION (IMPACT RESISTANCE) TESTS - PART 1: FALLING-WEIGHT TEST, LARGE-AREA INDENTER |
| DIN EN ISO 20567-3:2013-04 | PAINTS AND VARNISHES - DETERMINATION OF STONE-CHIP RESISTANCE OF COATINGS - PART 3: SINGLE-IMPACT TEST WITH A FREE-FLYING IMPACT BODY (ISO 20567-3:2012) |
| 16/30323865 DC : DRAFT APR 2016 | BS EN ISO 15110 - PAINTS AND VARNISHES - ARTIFICIAL WEATHERING INCLUDING ACIDIC DEPOSITION |
| 14/30309764 DC : 0 | BS EN ISO 20567-1 - PAINTS AND VARNISHES - DETERMINATION OF STONE-CHIP RESISTANCE OF COATINGS - PART 1: MULTI-IMPACT TESTING |
| BS 3900-F13:1986 | Methods of tests for paints; filiform corrosion test on steel |
| I.S. EN ISO 1517:1995 | PAINTS AND VARNISHES - SURFACE-DRYING TEST - BALLOTINI METHOD |
| DIN EN ISO 9117-2:2010-07 | Paints and varnishes - Drying tests - Part 2: Pressure test for stackability (ISO 9117-2:2010) |
| I.S. EN ISO 3678:1995 | PAINTS AND VARNISHES - PRINT-FREE TEST |
| I.S. EN ISO 12137-1:2006 | PAINTS AND VARNISHES - DETERMINATION OF MAR RESISTANCE - PART 1: METHOD USING A CURVED STYLUS |
| 12/30266874 DC | BS EN 1871. Road marking materials. Paint, thermoplastic and cold plastic materials. Specifications |
| 15/30284318 DC : 0 | BS EN ISO 9227 - CORROSION TESTS IN ARTIFICIAL ATMOSPHERES - SALT SPRAY TESTS |
| 10/30229703 DC : 0 | BS EN ISO 2812-3 - PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO LIQUIDS - PART 3: METHOD USING AN ABSORBENT MEDIUM |
| BS 3900-E17(1997) : 1997 AMD 16863 | METHODS OF TEST FOR PAINTS - DETERMINATION OF MAR RESISTANCE USING A CURVED STYLUS |
| UNI EN ISO 1518-1 : 2011 | PAINTS AND VARNISHES - DETERMINATION OF SCRATCH RESISTANCE - PART 1: CONSTANT-LOADING METHOD |
| 11/30217714 DC : 0 | BS EN ISO 15184 - PAINTS AND VARNISHES - DETERMINATION OF FILM HARDNESS BY PENCIL TEST |
| 12/30254917 DC : DRAFT JAN 2012 | BS EN 877 - CAST IRON PIPES AND FITTINGS, THEIR JOINTS AND ACCESSORIES FOR THE EVACUATION OF WATER FROM BUILDINGS - REQUIREMENTS, TEST METHODS AND QUALITY ASSURANCE |
| 14/30266805 DC : 0 | BS EN ISO 4624 - PAINTS AND VARNISHES - PULL-OFF TEST FOR ADHESION |
| 10/30210869 DC : 0 | BS EN ISO 9117-4 - PAINTS AND VARNISHES - DRYING TESTS - PART 4: TEST USING A MECHANICAL RECORDER |
| 11/30229694 DC : 0 | BS EN ISO 11997-2 - PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO CYCLIC CORROSION CONDITIONS - PART 2: WET (SALT FOG)/DRY/HUMIDITY/UV LIGHT |
| ISO 4623-1:2000 | Paints and varnishes Determination of resistance to filiform corrosion Part 1: Steel substrates |
| 14/30266791 DC : 0 | BS EN ISO 7784-2 - PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO ABRASION - PART 2: METHOD WITH ABRASIVE RUBBER WHEELS AND ROTATING TEST PANEL |
| BS EN ISO 8130-8:2010 | Coating powders Assessment of the storage stability of thermosetting powders |
| ONORM EN ISO 1518-2 : 2012 | PAINTS AND VARNISHES - DETERMINATION OF SCRATCH RESISTANCE - PART 2: VARIABLE-LOADING METHOD (ISO 1518-2:2011) |
| DIN 53150:2002-09 | PAINTS AND VARNISHES - DETERMINATION OF THE DRYING STAGE OF COATINGS (MODIFIED BANDOW-WOLFF METHOD) |
| BS 3900-E12:1986 | Methods of test for paints Indentation test (spherical or pyramidal) |
| BS 3900-E12.2:2000 | Methods of test for paints Determination of Knoop hardness by measurement of the indentation depth |
| DIN EN ISO 2812-2:2007-05 | PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO LIQUIDS - PART 2: WATER IMMERSION METHOD |
| DIN EN ISO 1518-2:2012-01 | PAINTS AND VARNISHES - DETERMINATION OF SCRATCH RESISTANCE - PART 2: VARIABLE-LOADING METHOD (ISO 1518-2:2011) |
| BS EN ISO 9117-6:2012 | Paints and varnishes. Drying tests Print-free test |
| DIN EN ISO 9117-1:2009-10 | Paints and varnishes - Drying tests - Part 1: Determination of through-dry state and through-dry time (ISO 9117-1:2009) |
| 14/30309758 DC : 0 | BS EN ISO 4623-2 - PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO FILIFORM CORROSION - PART 2: ALUMINIUM SUBSTRATES |
| 14/30298283 DC : 0 | BS ISO 18314-1 - ANALYTICAL COLORIMETRY - PART 1: PRACTICAL COLOUR MEASUREMENT |
| DIN ISO 8130-8 E : 2005 | COATING POWDERS - PART 8: ASSESSMENT OF THE STORAGE STABILITY OF THERMOSETTING POWDERS |
| UNE-EN ISO 9117-4:2013 | Paints and varnishes - Drying tests - Part 4: Test using a mechanical recorder (ISO 9117-4:2012) |
| 97/700599 DC : DRAFT JAN 1997 | PREN 4160 - AEROSPACE SERIES - PAINTS AND VARNISHES - DETERMINATION OF THE EFFECT OF THERMAL EXPOSURE |
| 17/30361497 DC : 0 | BS EN ISO 2812-5 - PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO LIQUIDS - PART 5: TEMPERATURE-GRADIENT OVEN METHOD |
| BS 3900-F14(1995) : 1995 AMD 9931 | METHODS OF TEST FOR PAINTS - DETERMINATION OF RESISTANCE TO ARTIFICIAL WEATHERING BY EXPOSURE TO FILTERED XENON-ARC RADIATION |
| BS EN ISO 15184:2012 | Paints and varnishes. Determination of film hardness by pencil test |
| BS ISO 18314-1 : 2015 | ANALYTICAL COLORIMETRY - PART 1: PRACTICAL COLOUR MEASUREMENT |
| ONORM EN ISO 1518-1 : 2011 | PAINTS AND VARNISHES - DETERMINATION OF SCRATCH RESISTANCE - PART 1: CONSTANT-LOADING METHOD |
| ISO 1518-1:2011 | Paints and varnishes Determination of scratch resistance Part 1: Constant-loading method |
| BS ISO 20567-1 : 2005 AMD 16853 | PAINTS AND VARNISHES - DETERMINATION OF STONE-CHIP RESISTANCE OF COATINGS - PART 1: MULTI-IMPACT TESTING |
| BS 3900-E18(1997) : 1997 AMD 16862 | METHODS OF TEST FOR PAINTS - DETERMINATION OF MAR RESISTANCE USING A POINTED STYLUS |
| I.S. EN ISO 15184:2012 | PAINTS AND VARNISHES - DETERMINATION OF FILM HARDNESS BY PENCIL TEST (ISO 15184:2012) |
| NF EN ISO 1518-2 : 2011 | PAINTS AND VARNISHES - DETERMINATION OF SCRATCH RESISTANCE - PART 2: VARIABLE-LOADING METHOD |
| 02/123757 DC : DRAFT OCT 2002 | ISO 20567-2 - PAINTS AND VARNISHES - DETERMINATION OF STONE CHIP RESISTANCE OF COATINGS - PART 2: SINGLE IMPACT TEST |
| BS ISO 11997-1 : 2005 AMD 16875 | PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO CYCLIC CORROSION CONDITIONS - PART 1: WET (SALT FOG)/DRY/HUMIDITY |
| BS 5629-2:1979 | Insulating varnishes containing solvent Test methods |
| 02/122653 DC : DRAFT JUN 2002 | BS EN ISO 6860 - PAINTS AND VARNISHES - BEND TEST (CONICAL MANDREL) |
| ISO 6270-3:2018 | Paints and varnishes — Determination of resistance to humidity — Part 3: Condensation (in-cabinet exposure with heated, bubbling water reservoir) |
| AEP-61 : 2009 | PERFORMANCE REQUIREMENTS FOR UNDERWATER HULL PAINT SYSTEMS |
| ISO 2812-4:2017 | Paints and varnishes — Determination of resistance to liquids — Part 4: Spotting methods |
| I.S. EN ISO 2812-2:2007 | PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO LIQUIDS - PART 2: WATER IMMERSION METHOD |
| I.S. EN ISO 9117-2:2010 | PAINTS AND VARNISHES - DRYING TESTS - PART 2: PRESSURE TEST FOR STACKABILITY |
| I.S. EN ISO 1518-2:2011 | PAINTS AND VARNISHES - DETERMINATION OF SCRATCH RESISTANCE - PART 2: VARIABLE-LOADING METHOD (ISO 1518-2:2011) |
| ISO 11503:1995 | Paints and varnishes — Determination of resistance to humidity (intermittent condensation) |
| I.S. EN ISO 2812-4:2017 | PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO LIQUIDS - PART 4: SPOTTING METHODS (ISO 2812-4:2017) |
| PREN 1825-1 : DRAFT 1995 | INSTALLATIONS FOR SEPARATION OF GREASE - PRINCIPLES OF DESIGN, PERFORMANCE AND TESTING, MARKING AND QUALITY CONTROL |
| UNI EN ISO 15184 : 2013 | PAINTS AND VARNISHES - DETERMINATION OF FILM HARDNESS BY PENCIL TEST |
| UNE-EN ISO 2812-3:2013 | Paints and varnishes - Determination of resistance to liquids - Part 3: Method using an absorbent medium (ISO 2812-3:2012) |
| EN ISO 2812-3:2012 | Paints and varnishes - Determination of resistance to liquids - Part 3: Method using an absorbent medium (ISO 2812-3:2012) |
| I.S. EN ISO 4623-1:2002 | PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO FILIFORM CORROSION - PART 1: STEEL SUBSTRATES |
| EN ISO 12944-9:2018 | Paints and varnishes - Corrosion protection of steel structures by protective paint systems - Part 9: Protective paint systems and laboratory performance test methods for offshore and related structures (ISO 12944-9:2018) |
| ISO 11997-1:2017 | Paints and varnishes — Determination of resistance to cyclic corrosion conditions — Part 1: Wet (salt fog)/dry/humid |
| ISO 15184:2012 | Paints and varnishes Determination of film hardness by pencil test |
| DIN EN ISO 11341:2004-12 | PAINTS AND VARNISHES - ARTIFICIAL WEATHERING AND EXPOSURE TO ARTIFICIAL RADIATION - EXPOSURE TO FILTERED XENON-ARC RADIATION |
| DIN EN ISO 6272-2:2011-11 | Paints and varnishes - Rapid-deformation (impact resistance) tests - Part 2: Falling-weight test, small-area indenter (ISO 6272-2:2011) |
| DIN EN ISO 11507:2007-05 | PAINTS AND VARNISHES - EXPOSURE OF COATINGS TO ARTIFICIAL WEATHERING - EXPOSURE TO FLUORESCENT UV LAMPS AND WATER |
| BS EN 12192-2:1999 | Products and systems for the protection and repair of concrete structures. Granulometry analysis Test method for fillers for polymer bonding agents |
| BS EN ISO 7784-2:2016 | Paints and varnishes. Determination of resistance to abrasion Method with abrasive rubber wheels and rotating test specimen |
| UNE-EN ISO 4623-2:2016 | Paints and varnishes - Determination of resistance to filiform corrosion - Part 2: Aluminium substrates (ISO 4623-2:2016) |
| BS EN ISO 1518:2001 | Paints and varnishes. Scratch test |
| BS EN ISO 1520:2006 | Paints and varnishes. Cupping test |
| BS EN ISO 1517:1995 | Paints and varnishes. Surface-drying test. Ballotini method |
| BS EN 877 : 1999 | CAST IRON PIPES AND FITTINGS, THEIR JOINTS AND ACCESSORIES FOR THE EVACUATION OF WATER FROM BUILDINGS - REQUIREMENTS, TEST METHODS AND QUALITY ASSURANCE |
| BS EN ISO 2813:2014 | Paints and varnishes. Determination of gloss value at 20 degrees, 60 degrees and 85 degrees |
| BS EN ISO 5659-2:2017 | Plastics. Smoke generation Determination of optical density by a single-chamber test |
| BS EN 13062:2003 | Products and systems for the protection and repair of concrete structures. Test method. Determination of thixotropy of products for protection of reinforcement |
| BS EN ISO 7784-3:2016 | Paints and varnishes. Determination of resistance to abrasion Method with abrasive-paper covered wheel and linearly reciprocating test specimen |
| BS EN ISO 7784-1:2016 | Paints and varnishes. Determination of resistance to abrasion Method with abrasive-paper covered wheels and rotating test specimen |
| I.S. EN ISO 7784-3:2016 | PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO ABRASION - PART 3: METHOD WITH ABRASIVE-PAPER COVERED WHEEL AND LINEARLY RECIPROCATING TEST SPECIMEN (ISO 7784-3:2016) |
| UNI EN 877 : 2007 | CAST IRON PIPES AND FITTINGS, THEIR JOINTS AND ACCESSORIES FOR THE EVACUATION OF WATER FROM BUILDINGS - REQUIREMENTS, TEST METHODS AND QUALITY ASSURANCE |
| DIN EN ISO 20567-1:2017-07 | PAINTS AND VARNISHES - DETERMINATION OF STONE-CHIP RESISTANCE OF COATINGS - PART 1: MULTI-IMPACT TESTING (ISO 20567-1:2017) |
| DIN EN ISO 20567-2:2017-07 | Paints and varnishes - Determination of stone-chip resistance of coatings - Part 2: Single-impact test with a guided impact body (ISO 20567-2:2017) |
| EN 61086-2:2004 | Coatings for loaded printed wire boards (conformal coatings) - Part 2: Methods of test |
| EN 10301:2003 | Steel tubes and fittings for on and offshore pipelines - Internal coating for the reduction of friction for conveyance of non corrosive gas |
| EN 12192-2:1999 | Products and systems for the protection and repair of concrete structures - Granulometry analysis - Part 2: Test method for fillers for polymer bonding agents |
| I.S. EN ISO 3231:1998 | PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO HUMID ATMOSPHERES CONTAINING SULFUR DIOXIDE |
| BS 3900-F18(2005) : 2005 | PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO CYCLIC CORROSION CONDITIONS - PART 1: WET (SALT FOG)/DRY/HUMIDITY |
| EN ISO 2812-1:2017 | Paints and varnishes - Determination of resistance to liquids - Part 1: Immersion in liquids other than water (ISO 2812-1:2017) |
| PREN 1871 : DRAFT 2012 | ROAD MARKING MATERIALS - PAINT, THERMOPLASTIC AND COLD PLASTIC MATERIALS - SPECIFICATIONS |
| 14/30289467 DC : 0 | BS EN ISO 3248 - PAINTS AND VARNISHES - DETERMINATION OF THE EFFECT OF HEAT |
| 01/121972 DC : DRAFT MAY 2001 | BS 3900-E12.3 - PAINTS AND VARNISHES - DETERMINATION OF MICRO-INDENTATION HARDNESS - PART 3: DETERMINATION OF UNIVERSAL HARDNESS AND RELATED PROPERTIES USING A VICKERS INDENTOR |
| BS 3900-J12(1998) : 1998 | METHODS OF TEST FOR PAINTS - TESTING OF COATING POWDERS - DETERMINATION OF COMPATIBILITY OF COATING POWDERS |
| UNE-EN ISO 9117-6:2013 | Paints and varnishes - Drying tests - Part 6: Print-free test (ISO 9117-6:2012) |
| BS EN ISO 9117-1:2009 | Paints and varnishes. Drying tests Determination of through-dry state and through-dry time |
| 12/30245694 DC : 0 | BS EN ISO 16927 - PAINTS AND VARNISHES - DETERMINATION OF THE OVERCOATABILITY AND RECOATABILITY OF A COATING |
| DIN EN ISO 8130-8:2011-02 | Coating powders - Part 8: Assessment of the storage stability of thermosetting powders (ISO 8130-8:1994) |
| 11/30215685 DC : 0 | BS EN ISO 15110 - PAINTS AND VARNISHES - ARTIFICIAL WEATHERING INCLUDING ACIDIC DEPOSITION |
| 12/30243830 DC : 0 | BS EN ISO 16474-1 - PAINTS AND VARNISHES - METHODS OF EXPOSURE TO LABORATORY LIGHT SOURCES - PART 1: GENERAL GUIDANCE |
| 12/30229691 DC : 0 | BS EN ISO 2813 - PAINTS AND VARNISHES - DETERMINATION OF SPECULAR GLOSS OF NON-METALLIC PAINT FILMS AT 20 DEGREES, 60 DEGREES AND 85 DEGREES |
| BS EN ISO 20567-3:2012 | Paints and varnishes. Determination of stone-chip resistance of coatings Single-impact test with a free-flying impact body |
| 17/30327456 DC : DRAFT SEP 2017 | BS ISO 20266 - PAINTS AND VARNISHES - DETERMINATION OF IMAGE CLARITY (DEGREE OF SHARPNESS OF REFLECTED OR TRANSMITTED IMAGE) |
| BS EN ISO 16927:2014 | Paints and varnishes. Determination of the overcoatability and recoatability of a coating |
| 10/30229700 DC : 0 | BS EN ISO 9117-6 - PAINTS AND VARNISHES - DRYING TESTS - PART 6: PRINT-FREE TEST |
| 11/30217720 DC : 0 | BS EN ISO 20567-3 - PAINTS AND VARNISHES - DETERMINATION OF STONE-CHIP RESISTANCE OF COATINGS - PART 3: SINGLE-IMPACT TEST WITH A FREE-FLYING IMPACT BODY |
| 14/30309761 DC : 0 | BS EN ISO 11997-1 - PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO CYCLIC CORROSION CONDITIONS - PART 1: WET (SALT FOG)/DRY/HUMIDITY |
| 14/30309767 DC : 0 | BS EN ISO 20567-2 - PAINTS AND VARNISHES - DETERMINATION OF STONE-CHIP RESISTANCE OF COATINGS - PART 2: SINGLE-IMPACT TEST WITH A GUIDED IMPACT BODY |
| BS ISO 27667:2011 | Road vehicles. Brake lining friction materials. Evaluation of corrosion effects on painted backing plates and brake shoes |
| BS EN ISO 1518-2:2011 | Paints and varnishes. Determination of scratch resistance Variable-loading method |
| BS 3900-F16(1997) : 1997 AMD 13289 | METHODS OF TEST FOR PAINTS - RESISTANCE TO ARTIFICIAL WEATHERING (UV RADIATION AND WATER) |
| 10/30206970 DC : 0 | BS EN ISO 6272-2 - PAINTS AND VARNISHES - RAPID-DEFORMATION (IMPACT RESISTANCE) TESTS - PART 2: FALLING-WEIGHT TEST, SMALL-AREA INDENTER |
| BS 3900-F9(1982) : AMD 8611 | METHODS OF TEST FOR PAINTS - DURABILITY TESTS ON PAINT FILMS - DETERMINATION OF RESISTANCE TO HUMIDITY (CONTINUOUS CONDENSATION) |
| BS 3900-G8(1993) : 1993 AMD 8356 | METHODS OF TEST FOR PAINTS - DETERMINATION OF RESISTANCE TO LIQUIDS. WATER IMMERSION METHOD |
| BS 3900-A16:1986 | Methods of test for paints. Tests on liquid paints (excluding chemical tests) Determination of natural spreading rate by brush application |
| BS 3900-F12:1985 | Methods of test for paint. Durability tests on paint films Determination of resistance to neutral salt spray |
| 07/30174613 DC : 0 | BS ISO 20340 - PAINTS AND VARNISHES - PERFORMANCE REQUIREMENTS FOR PROTECTIVE PAINT SYSTEMS FOR OFFSHORE AND RELATED STRUCTURES |
| 14/30266788 DC : 0 | BS EN ISO 7784-1 - PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO ABRASION - PART 1: METHOD WITH ABRASIVE-PAPER COVERED WHEELS AND ROTATING TEST PANEL |
| ISO 12944-9:2018 | Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 9: Protective paint systems and laboratory performance test methods for offshore and related structures |
| 16/30337293 DC : 0 | BS EN ISO 12944-9 - PAINTS AND VARNISHES - CORROSION PROTECTION OF STEEL STRUCTURES BY PROTECTIVE PAINT SYSTEMS - PART 9: PROTECTIVE PAINT SYSTEMS AND LABORATORY PERFORMANCE TEST METHODS FOR OFFSHORE AND RELATED STRUCTURES |
| BS EN ISO 2812-4:2017 | Paints and varnishes. Determination of resistance to liquids Spotting methods |
| STANAG 2836 : 0 | REMOVABLE PAINTS FOR CAMOUFLAGE |
| EN ISO 8130-8:2010 | Coating powders - Part 8: Assessment of the storage stability of thermosetting powders (ISO 8130-8:1994) |
| ISO 1518-2:2011 | Paints and varnishes Determination of scratch resistance Part 2: Variable-loading method |
| ISO 27667:2011 | Road vehicles — Brake lining friction materials — Evaluation of corrosion effects on painted backing plates and brake shoes |
| UNE-EN ISO 1518-1:2011 | Paints and varnishes - Determination of scratch resistance - Part 1: Constant-loading method (ISO 1518-1:2011) |
| UNE-EN ISO 8130-12:2011 | Coating powders - Part 12: Determination of compatibility (ISO 8130-12:1998) |
| I.S. EN ISO 9117-6:2012 | PAINTS AND VARNISHES - DRYING TESTS - PART 6: PRINT-FREE TEST (ISO 9117-6:2012) |
| BS EN ISO 16474-1:2013 | Paints and varnishes. Methods of exposure to laboratory light sources General guidance |
| BS EN ISO 1518-1:2011 | Paints and varnishes. Determination of scratch resistance Constant-loading method |
| UNI EN ISO 1518-2 : 2011 | PAINTS AND VARNISHES - DETERMINATION OF SCRATCH RESISTANCE - PART 2: VARIABLE- LOADING METHOD |
| DIN EN ISO 2812-3:2012-10 | PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO LIQUIDS - PART 3: METHOD USING AN ABSORBENT MEDIUM (ISO 2812-3:2012) |
| I.S. ISO 6441:1988 | PAINTS AND VARNISHES - INDENTATION TEST (SPHERICAL OR PYRAMIDAL) |
| DIN EN 877:2010-01 | Cast iron pipes and fittings, their joints and accessories for the evacuation of water from buildings - Requirements, test methods and quality assurance (includes Amendment A1:2006 and Corrigendum AC:2008) |
| DIN EN ISO 5659-2:2016-02 (Draft) | PLASTICS - SMOKE GENERATION - PART 2: DETERMINATION OF OPTICAL DENSITY BY A SINGLE-CHAMBER TEST (ISO 5659-2:2017) |
| DIN EN ISO 6272-1:2011-11 | Paints and varnishes - Rapid-deformation (impact resistance) tests - Part 1: Falling-weight test, large-area indenter (ISO 6272-1:2011) |
| DIN EN ISO 14577-4:2015-05 (Draft) | METALLIC MATERIALS - INSTRUMENTED INDENTATION TEST FOR HARDNESS AND MATERIALS PARAMETERS - PART 4: TEST METHOD FOR METALLIC AND NON-METALLIC COATINGS (ISO 14577-4:2016) |
| DIN EN ISO 1520:2007-11 | PAINTS AND VARNISHES - CUPPING TEST |
| DIN EN ISO 20567-2:2007-01 | PAINTS AND VARNISHES - DETERMINATION OF STONE-CHIP RESISTANCE OF COATINGS - PART 2: SINGLE-IMPACT TEST WITH A GUIDED IMPACT BODY (ISO 20567-2:2017) |
| ISO 2810:2004 | Paints and varnishes Natural weathering of coatings Exposure and assessment |
| ISO 2815:2003 | Paints and varnishes Buchholz indentation test |
| ISO 15711:2003 | Paints and varnishes — Determination of resistance to cathodic disbonding of coatings exposed to sea water |
| UNE-EN ISO 20567-1:2017 | Paints and varnishes - Determination of stone-chip resistance of coatings - Part 1: Multi-impact testing (ISO 20567-1:2017) |
| UNE-EN ISO 4624:2016 | Paints and varnishes - Pull-off test for adhesion (ISO 4624:2016) |
| BS EN ISO 12137-1:2006 | Paints and varnishes. Determination of mar resistance Method using a curved stylus |
| UNE-EN ISO 9227:2017 | Corrosion tests in artificial atmospheres - Salt spray tests (ISO 9227:2017) |
| BS EN ISO 11997-2:2013 | Paints and varnishes. Determination of resistance to cyclic corrosion conditions Wet (salt fog)/dry/humidity/UV light |
| EN ISO 2812-2:2007 | Paints and varnishes - Determination of resistance to liquids - Part 2: Water immersion method (ISO 2812-2:2007) |
| I.S. EN ISO 6860:2006 | PAINTS AND VARNISHES - BEND TEST (CONICAL MANDREL) |
| I.S. EN ISO 1520:2006 | PAINTS AND VARNISHES - CUPPING TEST |
| ONORM EN ISO 2409 : 2013 | PAINTS AND VARNISHES - CROSS-CUT TEST (ISO 2409:2013) |
| I.S. EN ISO 6272-1:2011 | PAINTS AND VARNISHES - RAPID-DEFORMATION (IMPACT RESISTANCE) TESTS - PART 1: FALLING-WEIGHT TEST, LARGE-AREA INDENTER |
| I.S. EN ISO 4624:2016 | PAINTS AND VARNISHES - PULL-OFF TEST FOR ADHESION (ISO 4624:2016) |
| I.S. EN ISO 2813:2014 | PAINTS AND VARNISHES - DETERMINATION OF GLOSS VALUE AT 20 DEGREES, 60 DEGREES AND 85 DEGREES (ISO 2813:2014) |
| I.S. EN ISO 1519:2011 | PAINTS AND VARNISHES - BEND TEST (CYLINDRICAL MANDREL) |
| DIN EN ISO 11341:1998-02 | PAINTS AND VARNISHES - ARTIFICIAL WEATHERING AND EXPOSURE TO ARTIFICIAL RADIATION - EXPOSURE TO FILTERED XENON-ARC RADIATION |
| UNI EN ISO 2409 : 2013 | PAINTS AND VARNISHES - CROSS-CUT TEST |
| EN ISO 16474-3:2013 | Paints and varnishes - Methods of exposure to laboratory light sources - Part 3: Fluorescent UV lamps (ISO 16474-3:2013) |
| I.S. EN ISO 1522:2006 | PAINTS AND VARNISHES - PENDULUM DAMPING TEST |
| I.S. EN ISO 11997-2:2013 | PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO CYCLIC CORROSION CONDITIONS - PART 2: WET (SALT FOG)/DRY/HUMIDITY/UV LIGHT (ISO 11997-2:2013) |
| I.S. EN ISO 5659-2:2017 | PLASTICS - SMOKE GENERATION - PART 2: DETERMINATION OF OPTICAL DENSITY BY A SINGLE-CHAMBER TEST (ISO 5659-2:2017) |
| I.S. EN ISO 6272-2:2011 | PAINTS AND VARNISHES - RAPID-DEFORMATION (IMPACT RESISTANCE) TESTS - PART 2: FALLING-WEIGHT TEST, SMALL-AREA INDENTER |
| I.S. EN ISO 4623-2:2016 | PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO FILIFORM CORROSION - PART 2: ALUMINIUM SUBSTRATES (ISO 4623-2:2016) |
| I.S. EN ISO 14577-4:2016 | METALLIC MATERIALS - INSTRUMENTED INDENTATION TEST FOR HARDNESS AND MATERIALS PARAMETERS - PART 4: TEST METHOD FOR METALLIC AND NON-METALLIC COATINGS (ISO 14577-4:2016) |
| I.S. EN ISO 7784-2:2016 | PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO ABRASION - PART 2: METHOD WITH ABRASIVE RUBBER WHEELS AND ROTATING TEST SPECIMEN (ISO 7784-2:2016) |
| I.S. EN ISO 9227:2017 | CORROSION TESTS IN ARTIFICIAL ATMOSPHERES - SALT SPRAY TESTS (ISO 9227:2017) |
| I.S. EN ISO 20567-1:2017 | PAINTS AND VARNISHES - DETERMINATION OF STONE-CHIP RESISTANCE OF COATINGS - PART 1: MULTI-IMPACT TESTING (ISO 20567-1:2017) |
| I.S. EN ISO 13803:2014 | PAINTS AND VARNISHES - DETERMINATION OF HAZE ON PAINT FILMS AT 20 DEGREES (ISO 13803:2014) |
| I.S. EN ISO 20567-2:2017 | PAINTS AND VARNISHES - DETERMINATION OF STONE-CHIP RESISTANCE OF COATINGS - PART 2: SINGLE-IMPACT TEST WITH A GUIDED IMPACT BODY (ISO 20567-2:2017) |
| I.S. EN ISO 3248:2016 | PAINTS AND VARNISHES - DETERMINATION OF THE EFFECT OF HEAT (ISO 3248:2016) |
| I.S. EN ISO 7784-1:2016 | PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO ABRASION - PART 1: METHOD WITH ABRASIVE-PAPER COVERED WHEELS AND ROTATING TEST SPECIMEN (ISO 7784-1:2016) |
| BS 3900-G7(1998) : 1998 AMD 12096 | METHODS OF TEST FOR PAINTS - DETERMINATION OF THE EFFECT OF HEAT |
| BS 3900-D1:1978 | Methods of test for paints. Optical tests on paint films Visual comparison of the colour of paints |
| BS 3900-F12(1997) : 1997 AMD 13288 | METHODS OF TEST FOR PAINTS - DETERMINATION OF RESISTANCE TO NEUTRAL SALT SPRAY (FOG) |
| VDI/VDE 2616 Blatt 2:2014-07 | Hardness testing of plastics and elastomers |
| BS 3900-D1(1998) : 1998 AMD 13287 | METHODS OF TEST FOR PAINTS - VISUAL COMPARISON OF THE COLOUR OF PAINTS |
| BS 3900-E5(1998) : 1998 AMD 12090 | METHODS OF TEST FOR PAINTS - PENDULUM DAMPING TESTING |
| VDI 3958 Blatt 13:2014-08 | Environmental simulation - Tropicalisation of paint coatings for outdoor use - Test methods |
| BS 3900-C5:1992 | Methods of test for paints. Tests associated with paint film formation Determination of film thickness |
| UNE-EN ISO 8130-8:2011 | Coating powders - Part 8: Assessment of the storage stability of thermosetting powders (ISO 8130-8:1994) |
| BS 3900-B17:1991 | Methods of test for paints Preparation of acid extracts from dried paint films |
| BS EN ISO 12137:2011 | Paints and varnishes. Determination of mar resistance |
| I.S. EN ISO 4623:1995 | PAINTS AND VARNISHES - FILIFORM CORROSION TEST ON STEEL |
| BS EN ISO 2812-5:2007 | Paints and varnishes. Determination of resistance to liquids Temperature-gradient oven method |
| BS EN ISO 2812-1:2017 | Paints and varnishes. Determination of resistance to liquids Immersion in liquids other than water |
| BS EN ISO 9117-3:2010 | Paints and varnishes. Drying tests Surface-drying test using ballotini |
| NF EN ISO 9117-2 : 2010 | PAINTS AND VARNISHES - DRYING TESTS - PART 2: PRESSURE TEST FOR STACKABILITY |
| I.S. EN ISO 11507:2007 | PAINTS AND VARNISHES - EXPOSURE OF COATINGS TO ARTIFICIAL WEATHERING - EXPOSURE TO FLUORESCENT UV LAMPS AND WATER |
| UNE-EN ISO 16927:2014 | Paints and varnishes - Determination of the overcoatability and recoatability of a coating (ISO 16927:2014) |
| AEP-64 : 2012 | PERFORMANCE REQUIREMENTS FOR PAINT SYSTEMS RESISTANT TO CHEMICAL AGENTS AND DECONTAMINANTS, FOR THE PROTECTION OF LAND MILITARY EQUIPMENT |
| 09/30196695 DC : 0 | BS ISO 1519 - PAINTS AND VARNISHES - BEND TEST (CYLINDRICAL MANDREL) |
| EN IEC 62631-3-11:2018 | Dielectric and resistive properties of solid insulating materials - Part 3-11: Determination of resistive properties (DC methods) - Volume resistance and volume resistivity - Method for impregnation and coating materials |
| DIN EN ISO 9117-3:2010-07 | Paints and varnishes - Drying tests - Part 3: Surface-drying test using ballotini (ISO 9117-3:2010) |
| NF EN ISO 8130-8 : 2011 | COATING POWDERS - PART 8: ASSESSMENT OF THE STORAGE STABILITY OF THERMOSETTING POWDERS |
| DIN EN ISO 12137:2012-01 | Paints and varnishes - Determination of mar resistance (ISO 12137:2011) |
| 15/30268151 DC : 0 | BS EN ISO 14577-4 - METALLIC MATERIALS - INSTRUMENTED INDENTATION TEST FOR HARDNESS AND MATERIALS PARAMETERS - PART 4: TEST METHOD FOR METALLIC AND NON-METALLIC COATINGS |
| 04/30012206 DC : DRAFT AUG 2004 | PREN 4592 - AEROSPACE SERIES - PAINTS AND VARNISHES - DETERMINATION OF INFRARED REFLECTANCE |
| BS 3900-E11(1985) : 1985 AMD 8612 | METHODS OF TEST FOR PAINTS - MECHANICAL TESTS ON PAINT FILMS - BEND TEST (CONICAL MANDREL) |
| 18/30371134 DC : DRAFT APR 2018 | BS EN ISO 8130-12 - COATING POWDERS - PART 12: DETERMINATION OF COMPATIBILITY |
| DIN EN ISO 17132:2008-01 | PAINTS AND VARNISHES - T-BEND TEST |
| 95/101288 DC : DRAFT FEB 1995 | PREN 1825-1 - INSTALLATIONS FOR SEPARATION OF GREASE - PART 1: PRINCIPLES OF DESIGN, PERFORMANCE AND TESTING, MARKING AND QUALITY CONTROL |
| 12/30229888 DC : 0 | BS EN ISO 16474-3 - PAINTS AND VARNISHES - METHODS OF EXPOSURE TO LABORATORY LIGHT SOURCES - PART 3: FLUORESCENT UV LAMPS |
| 17/30344544 DC : 0 | BS EN ISO 2812-2 - PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO LIQUIDS - PART 2: WATER IMMERSION METHOD |
| BS EN ISO 4623-1:2002 | Paints and varnishes. Determination of resistance to filiform corrosion Steel substrates |
| BS EN IEC 62631-3-11:2018 | Dielectric and resistive properties of solid insulating materials Determination of resistive properties (DC methods). Volume resistance and volume resistivity. Method for impregnation and coating materials |
| SAE AMS3095A | Paint: High Gloss For Airline Exterior System |
| BS ISO 16862 : 2003 AMD 16867 | PAINTS AND VARNISHES - EVALUATION OF SAG RESISTANCE |
| UNE-EN ISO 15184:2013 | Paints and varnishes - Determination of film hardness by pencil test (ISO 15184:2012) |
| ONORM EN ISO 2812-5 : 2008 | PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO LIQUIDS - PART 5: TEMPERATURE-GRADIENT OVEN METHOD |
| ISO 2812-5:2007 | Paints and varnishes Determination of resistance to liquids Part 5: Temperature-gradient oven method |
| I.S. EN ISO 9117-5:2012 | PAINTS AND VARNISHES - DRYING TESTS - PART 5: MODIFIED BANDOW-WOLFF TEST (ISO 9117-5:2012) |
| ISO 3668:2017 | Paints and varnishes — Visual comparison of colour of paints |
| AEP-65 : 2012 | PERFORMANCE REQUIREMENTS AND TEST METHOD FOR PAINT SYSTEMS RESISTANT TO CHEMICAL WARFARE AGENTS |
| I.S. EN ISO 16474-1:2013 | PAINTS AND VARNISHES - METHODS OF EXPOSURE TO LABORATORY LIGHT SOURCES - PART 1: GENERAL GUIDANCE (ISO 16474-1:2013) |
| I.S. EN IEC 62631-3-11:2018 | DIELECTRIC AND RESISTIVE PROPERTIES OF SOLID INSULATING MATERIALS - PART 3-11: DETERMINATION OF RESISTIVE PROPERTIES (DC METHODS) - VOLUME RESISTANCE AND VOLUME RESISTIVITY - METHOD FOR IMPREGNATION AND COATING MATERIALS |
| AEP-60 : 2009 | PERFORMANCE REQUIREMENTS FOR EXTERIOR TOPSIDES COATINGS |
| DIN EN ISO 2812-5:2007-05 | PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO LIQUIDS - PART 5: TEMPERATURE-GRADIENT OVEN METHOD |
| I.S. EN ISO 8130-8:2010 | COATING POWDERS - PART 8: ASSESSMENT OF THE STORAGE STABILITY OF THERMOSETTING POWDERS |
| DIN EN ISO 16474-1:2014-03 | PAINTS AND VARNISHES - METHODS OF EXPOSURE TO LABORATORY LIGHT SOURCES - PART 1: GENERAL GUIDANCE (ISO 16474-1:2013) |
| UNI EN ISO 16474-1 : 2014 | PAINTS AND VARNISHES - METHODS OF EXPOSURE TO LABORATORY LIGHT SOURCES - PART 1: GENERAL GUIDANCE |
| ISO 11659-3:2004 | Textile machinery and accessories Machine parts in contact with textile processing oils Part 3: Determination of the impact on lacquers |
| ONORM EN ISO 16474-1 : 2014 | PAINTS AND VARNISHES - METHODS OF EXPOSURE TO LABORATORY LIGHT SOURCES - PART 1: GENERAL GUIDANCE (ISO 16474-1:2013) |
| ISO 6441-2:1999 | Paints and varnishes Determination of micro-indentation hardness Part 2: Knoop hardness by measurement of indentation depth under load |
| BS EN ISO 2812-2:2007 | Paints and varnishes. Determination of resistance to liquids Water immersion method |
| UNE-EN ISO 2812-4:2018 | Paints and varnishes - Determination of resistance to liquids - Part 4: Spotting methods (ISO 2812-4:2017) |
| UNE-EN ISO 15110:2018 | Paints and varnishes - Artificial weathering including acidic deposition (ISO 15110:2017) |
| I.S. EN ISO 12944-9:2018 | PAINTS AND VARNISHES - CORROSION PROTECTION OF STEEL STRUCTURES BY PROTECTIVE PAINT SYSTEMS - PART 9: PROTECTIVE PAINT SYSTEMS AND LABORATORY PERFORMANCE TEST METHODS FOR OFFSHORE AND RELATED STRUCTURES (ISO 12944-9:2018) |
| UNI EN ISO 16927 : 2014 | PAINTS AND VARNISHES - DETERMINATION OF THE OVERCOATABILITY AND RECOATABILITY OF A COATING |
| UNI EN ISO 2812-3 : 2012 | PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO LIQUIDS - PART 3: METHOD USING AN ABSORBENT MEDIUM |
| CEI EN 61086-2 : 2005 | COATINGS FOR LOADED PRINTED WIRE BOARDS (CONFORMAL COATINGS) - PART 2: METHODS OF TEST |
| UNI EN ISO 9117-6 : 2012 | PAINTS AND VARNISHES - DRYING TESTS - PART 6: PRINT-FREE TEST |
| NF EN ISO 12137 : 2011 | PAINTS AND VARNISHES - DETERMINATION OF MAR RESISTANCE |
| EN ISO 8130-12:2010 | Coating powders - Part 12: Determination of compatibility (ISO 8130-12:1998) |
| ISO 18314-1:2015 | Analytical colorimetry Part 1: Practical colour measurement |
| I.S. EN 60464-2:2002 | VARNISHES USED FOR ELECTRICAL INSULATION - PART 2: METHODS OF TEST |
| ISO 2813:2014 | Paints and varnishes — Determination of gloss value at 20°, 60° and 85° |
| EN ISO 9227:2017 | Corrosion tests in artificial atmospheres - Salt spray tests (ISO 9227:2017) |
| DIN EN ISO 6860:2006-06 | Paints and varnishes - Bend test (conical mandrel) (ISO 6860:2006) |
| EN ISO 3668:2001 | Paints and varnishes - Visual comparison of the colour of paints (ISO 3668:1998) |
| DIN EN ISO 16862:2006-08 | Paints and varnishes - Evaluation of sag resistance (ISO 16862:2003) |
| DIN EN ISO 11997-2:2013-12 | PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO CYCLIC CORROSION CONDITIONS - PART 2: WET (SALT FOG)/DRY/HUMIDITY/UV LIGHT (ISO 11997-2:2013) |
| UNE-EN ISO 3248:2017 | Paints and varnishes - Determination of the effect of heat (ISO 3248:2016) |
| DIN EN ISO 13803:2015-02 | PAINTS AND VARNISHES - DETERMINATION OF HAZE ON PAINT FILMS AT 20 DEGREES (ISO 13803:2014) |
| DIN EN ISO 2815:2003-10 | PAINTS AND VARNISHES - BUCHHOLZ INDENTATION TEST |
| DIN EN ISO 1519:2011-04 | Paints and varnishes - Bend test (cylindrical mandrel) (ISO 1519:2011) |
| ISO 6272-1:2011 | Paints and varnishes — Rapid-deformation (impact resistance) tests — Part 1: Falling-weight test, large-area indenter |
| BS EN ISO 2810:2004 | Paints and varnishes. Natural weathering of coatings. Exposure and assessment |
| BS EN ISO 20567-2:2017 | Paints and varnishes. Determination of stone-chip resistance of coatings Single-impact test with a guided impact body |
| UNE-EN ISO 7784-1:2016 | Paints and varnishes - Determination of resistance to abrasion - Part 1: Method with abrasive-paper covered wheels and rotating test specimen (ISO 7784-1:2016) |
| ISO 2409:2013 | Paints and varnishes Cross-cut test |
| BS EN ISO 4623:1995 | Paints and varnishes. Filiform corrosion test on steel |
| ISO 17132:2007 | Paints and varnishes T-bend test |
| ISO 16862:2003 | Paints and varnishes Evaluation of sag resistance |
| ISO 11341:2004 | Paints and varnishes Artificial weathering and exposure to artificial radiation Exposure to filtered xenon-arc radiation |
| ISO 1517:1973 | Paints and varnishes Surface-drying test Ballotini method |
| UNE-EN ISO 7784-2:2016 | Paints and varnishes - Determination of resistance to abrasion - Part 2: Method with abrasive rubber wheels and rotating test specimen (ISO 7784-2:2016) |
| ISO 2812-1:2017 | Paints and varnishes — Determination of resistance to liquids — Part 1: Immersion in liquids other than water |
| UNE-EN ISO 2813:2015 | Paints and varnishes - Determination of gloss value at 20º, 60º and 85º (ISO 2813:2014) |
| UNE-EN ISO 6272-1:2012 | Paints and varnishes - Rapid-deformation (impact resistance) tests - Part 1: Falling-weight test, large-area indenter (ISO 6272-1:2011) |
| BS EN ISO 15710:2006 | Paints and varnishes. Corrosion testing by alternate immersion in and removal from a buffered sodium chloride solution |
| UNE-EN ISO 1519:2011 | Paints and varnishes - Bend test (cylindrical mandrel) (ISO 1519:2011) |
| UNE-EN ISO 6272-2:2012 | Paints and varnishes - Rapid-deformation (impact resistance) tests - Part 2: Falling-weight test, small-area indenter (ISO 6272-2:2011) |
| ISO 3248:2016 | Paints and varnishes Determination of the effect of heat |
| DIN EN ISO 7253:2002-04 | PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO NEUTRAL SALT SPRAY (FOG) |
| EN ISO 2812-5:2007 | Paints and varnishes - Determination of resistance to liquids - Part 5: Temperature-gradient oven method (ISO 2812-5:2007) |
| I.S. EN ISO 2409:2013 | PAINTS AND VARNISHES - CROSS-CUT TEST (ISO 2409:2013) |
| EN ISO 2409:2013 | Paints and varnishes - Cross-cut test (ISO 2409:2013) |
| EN 1871:2000 | Road marking materials - Physical properties |
| I.S. EN ISO 2810:2004 | PAINTS AND VARNISHES - NATURAL WEATHERING OF COATINGS - EXPOSURE AND ASSESSMENT |
| EN ISO 2810:2004 | Paints and varnishes - Natural weathering of coatings - Exposure and assessment (ISO 2810:2004) |
| EN ISO 1522:2006 | Paints and varnishes - Pendulum damping test (ISO 1522:2006) |
| EN ISO 13803:2014 | Paints and varnishes - Determination of haze on paint films at 20° (ISO 13803:2014) |
| EN ISO 9117-5:2012 | Paints and varnishes - Drying tests - Part 5: Modified Bandow-Wolff test (ISO 9117-5:2012) |
| EN ISO 4623-2:2016 | Paints and varnishes - Determination of resistance to filiform corrosion - Part 2: Aluminium substrates (ISO 4623-2:2016) |
| EN ISO 17132:2007 | Paints and varnishes - T-bend test (ISO 17132:2007) |
| UNI EN ISO 6272-1 : 2013 | PAINTS AND VARNISHES - RAPID-DEFORMATION (IMPACT RESISTANCE) TESTS - PART 1: FALLING-WEIGHT TEST, LARGE-AREA INDENTER |
| UNI EN ISO 6272-2 : 2013 | PAINTS AND VARNISHES - RAPID-DEFORMATION (IMPACT RESISTANCE) TESTS - PART 2: FALLING-WEIGHT TEST, SMALL-AREA INDENTER |
| EN ISO 2813:2014 | Paints and varnishes - Determination of gloss value at 20°, 60° and 85° (ISO 2813:2014) |
| UNI EN ISO 11997-2 : 2014 | PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO CYCLIC CORROSION CONDITIONS - PART 2: WET (SALT FOG)/DRY/HUMIDITY/UV LIGHT |
| UNI EN ISO 1519 : 2011 | PAINTS AND VARNISHES - BEND TEST (CYLINDRICAL MANDREL) |
| EN ISO 6860:2006 | Paints and varnishes - Bend test (conical mandrel) (ISO 6860:2006) |
| UNE-EN ISO 16474-3:2014 | Paints and varnishes - Methods of exposure to laboratory light sources - Part 3: Fluorescent UV lamps (ISO 16474-3:2013) |
| UNE-EN ISO 1518-2:2012 | Paints and varnishes - Determination of scratch resistance - Part 2: Variable-loading method (ISO 1518-2:2011) |
| AFAP-5 : 2010 | NATO REACTION-TO-FIRE TESTS FOR MATERIALS - HEAT RELEASE RATE |
| ISO 8130-12:1998 | Coating powders Part 12: Determination of compatibility |
| I.S. EN ISO 20567-3:2012 | PAINTS AND VARNISHES - DETERMINATION OF STONE-CHIP RESISTANCE OF COATINGS - PART 3: SINGLE-IMPACT TEST WITH A FREE-FLYING IMPACT BODY (ISO 20567-3:2012) |
| DIN ISO 1520:1982-02 | PAINTS AND VARNISHES - CUPPING TEST |
| 12/30249839 DC : 0 | BS EN ISO 9227 - CORROSION TESTS IN ARTIFICIAL ATMOSPHERES - SALT SPRAY TESTS |
| BS EN ISO 9117-4:2012 | Paints and varnishes. Drying tests Test using a mechanical recorder |
| BS 3900-F19(2000) : 2000 AMD 16874 | METHODS OF TEST FOR PAINT - DURABILITY TESTS ON PAINT FILMS - DETERMINATION OF RESISTANCE TO CYCLIC CORROSION CONDITIONS - WET (SALT FOG)/DRY/HUMIDITY/UV LIGHT |
| BS 3900-F18:1998 | Methods of test for paint. Durability tests on paint films Determination of resistance to corrosion under a wet (salt fog)/dry/humidity cycle |
| 06/30148614 DC : 0 | EN ISO 17132 - PAINTS AND VARNISHES - T-BEND TEST |
| I.S. EN ISO 4622:1995 | PAINTS AND VARNISHES - PRESSURE TEST FOR STACKABILITY |
| I.S. EN ISO 12137-2:2006 | PAINTS AND VARNISHES - DETERMINATION OF MAR RESISTANCE - PART 2: METHOD USING A POINTED STYLUS |
| UNI EN ISO 9117-3 : 2010 | PAINTS AND VARNISHES - DRYING TESTS - PART 3: SURFACE-DRYING TEST USING BALLOTINI |
| UNI EN ISO 16474-3 : 2014 | PAINTS AND VARNISHES - METHODS OF EXPOSURE TO LABORATORY LIGHT SOURCES - PART 3: FLUORESCENT UV LAMPS |
| DIN EN ISO 16927 E : 2014 | PAINTS AND VARNISHES - DETERMINATION OF THE OVERCOATABILITY AND RECOATABILITY OF A COATING (ISO 16927:2014) |
| BS EN ISO 8130-12:2010 | Coating powders Determination of compatibility |
| BS 3900-E12.1:2000 | Methods of test for paints Determination of Knoop hardness by measurement of the indentation length using a microscope |
| 08/30189495 DC : DRAFT OCT 2008 | BS EN ISO 9117-3 - PAINTS AND VARNISHES - DRYING TESTS - PART 3: SURFACE-DRYING TEST USING BALLOTINI |
| ONORM EN ISO 16474-3 : 2014 | PAINTS AND VARNISHES - METHODS OF EXPOSURE TO LABORATORY LIGHT SOURCES - PART 3: FLUORESCENT UV LAMPS (ISO 16474-3:2013) |
| 10/30197386 DC : 0 | BS ISO 12013-2 - PAINTS AND VARNISHES - DETERMINATION OF CURING CHARACTERISTICS USING A FREE-DAMPED OSCILLATION METHOD - PART 2: GLASS-TRANSITION TEMPERATURE |
| 17/30361500 DC : 0 | BS EN ISO 4623-1 - PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO FILIFORM CORROSION - PART 1: STEEL SUBSTRATES |
| UNI EN ISO 9117-4 : 2012 | PAINTS AND VARNISHES - DRYING TESTS - PART 4: TEST USING A MECHANICAL RECORDER |
| 10/30207417 DC : 0 | BS EN ISO 2409 - PAINTS AND VARNISHES - CROSS-CUT TEST |
| BS 3900-C7:1982 | Methods of test for paints. Tests associated with paint film formation Pressure test for stackability |
| BS 3900-E15(1997) : 1997 | METHODS OF TEST FOR PAINTS - DETERMINATION OF RESISTANCE TO ABRASION (ROTATING ABRASIVE RUBBER WHEEL) |
| DIN ISO 8130-12:2005-03 | COATING POWDERS - PART 12: DETERMINATION OF COMPATIBILITY |
| BS ISO 6272-2 : 2002 AMD 16866 | PAINTS AND VARNISHES - RAPID-DEFORMATION (IMPACT RESISTANCE) TESTS - PART 2: FALLING-WEIGHT TEST, SMALL-AREA INDENTER |
| BS 3900-F20(2004) : 2004 | PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO FILIFORM CORROSION - PART 2: ALUMINIUM SUBSTRATES |
| BS 3900-E13(1993) : 1993 AMD 8354 | METHODS OF TEST FOR PAINTS - FALLING WEIGHT RESISTANCE (IMPACT) |
| BS EN ISO 16474-3:2013 | Paints and varnishes. Methods of exposure to laboratory light sources Fluorescent UV lamps |
| DIN EN ISO 9117-5:2012-11 | Paints and varnishes - Drying tests - Part 5: Modified Bandow-Wolff test (ISO 9117-5:2012) |
| BS ISO 12013-1:2012 | Paints and varnishes. Determination of curing characteristics using a free damped oscillation method Start temperature of the curing reaction |
| BS ISO 15710 : 2002 AMD 16861 | PAINTS AND VARNISHES - CORROSION TESTING BY ALTERNATE IMMERSION IN AND REMOVAL FROM A BUFFERED SODIUM CHLORIDE SOLUTION |
| DIN EN ISO 9117-4:2012-11 | Paints and varnishes - Drying tests - Part 4: Test using a mechanical recorder (ISO 9117-4:2012) |
| BS 3900-C8(1978) : 1978 AMD 8613 | METHODS OF TEST FOR PAINTS - TESTS ASSOCIATED WITH PAINT FILM FORMATION - PRINT-FREE TEST |
| 14/30298904 DC : 0 | BS EN ISO 7784-3 - PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO ABRASION - PART 3: METHOD WITH ABRASIVE-PAPER COVERED WHEEL AND LINEARLY RECIPROCATING TEST PANEL |
| BS 3900-E10:1979 | Methods of test for paints Pull-off test for adhesion |
| BS EN ISO 9117-2:2010 | Paints and varnishes. Drying tests Pressure test for stackability |
| NF EN ISO 1518-1 : 2011 | PAINTS AND VARNISHES - DETERMINATION OF SCRATCH RESISTANCE - PART 1: CONSTANT-LOADING METHOD |
| BS EN ISO 9117-5:2012 | Paints and varnishes. Drying tests Modified Bandow-Wolff test |
| I.S. EN ISO 9117-4:2012 | PAINTS AND VARNISHES - DRYING TESTS - PART 4: TEST USING A MECHANICAL RECORDER (ISO 9117-4:2012) |
| BS 3900-E16(2000) : 2000 AMD 16868 | METHODS OF TEST FOR PAINTS - DETERMINATION OF RESISTANCE TO ABRASION (RECIPROCATING TEST PANEL METHOD) |
| UNI EN ISO 9117-2 : 2010 | PAINTS AND VARNISHES - DRYING TESTS - PART 2: PRESSURE TEST FOR STACKABILITY |
| ISO 12013-2:2012 | Paints and varnishes — Determination of curing characteristics using a free damped oscillation method — Part 2: Glass transition temperature |
| BS EN 60464-2:2001 | Varnishes used for electrical insulation Methods of test |
| UNE-EN ISO 20567-3:2013 | Paints and varnishes - Determination of stone-chip resistance of coatings - Part 3: Single-impact test with a free-flying impact body (ISO 20567-3:2012) |
| I.S. EN ISO 11997-1:2017 | PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO CYCLIC CORROSION CONDITIONS - PART 1: WET (SALT FOG)/DRY/HUMID (ISO 11997-1:2017) |
| UNI EN ISO 9117-5 : 2012 | PAINTS AND VARNISHES - DRYING TESTS - PART 5: MODIFIED BANDOW-WOLFF TEST |
| I.S. EN ISO 16474-3:2013 | PAINTS AND VARNISHES - METHODS OF EXPOSURE TO LABORATORY LIGHT SOURCES - PART 3: FLUORESCENT UV LAMPS (ISO 16474-3:2013) |
| ISO 6441-1:1999 | Paints and varnishes Determination of micro-indentation hardness Part 1: Knoop hardness by measurement of indentation length |
| I.S. EN ISO 15110:2017 | PAINTS AND VARNISHES - ARTIFICIAL WEATHERING INCLUDING ACIDIC DEPOSITION (ISO 15110:2017) |
| I.S. EN ISO 9117-3:2010 | PAINTS AND VARNISHES - DRYING TESTS - PART 3: SURFACE-DRYING TEST USING BALLOTINI |
| AFAP-4 : 2010 | NATO REACTION-TO-FIRE TESTS FOR MATERIALS - SURFACE SPREAD OF FLAME |
| ISO 20340:2009 | Paints and varnishes Performance requirements for protective paint systems for offshore and related structures |
| UNE-EN ISO 16474-1:2014 | Paints and varnishes - Methods of exposure to laboratory light sources - Part 1: General guidance (ISO 16474-1:2013) |
| EN ISO 11997-1:2017 | Paints and varnishes - Determination of resistance to cyclic corrosion conditions - Part 1: Wet (salt fog)/dry/humid (ISO 11997-1:2017) |
| NF EN ISO 8130-12 : 2011 | COATING POWDERS - PART 12: DETERMINATION OF COMPATIBILITY |
| UNI EN ISO 8130-12 : 2011 | COATING POWDERS - PART 12: DETERMINATION OF COMPATIBILITY |
| BS EN ISO 2812-3:2012 | Paints and varnishes. Determination of resistance to liquids Method using an absorbent medium |
| UNE-EN ISO 9117-5:2013 | Paints and varnishes - Drying tests - Part 5: Modified Bandow-Wolff test (ISO 9117-5:2012) |
| I.S. EN ISO 17132:2007 | PAINTS AND VARNISHES - T-BEND TEST |
| ISO 12013-1:2012 | Paints and varnishes — Determination of curing characteristics using a free damped oscillation method — Part 1: Start temperature of the curing reaction |
| ISO 7724-2:1984 | Paints and varnishes Colorimetry Part 2: Colour measurement |
| ISO 2812-2:2007 | Paints and varnishes Determination of resistance to liquids Part 2: Water immersion method |
| EN ISO 15110:2017 | Paints and varnishes - Artificial weathering including acidic deposition (ISO 15110:2017) |
| I.S. EN ISO 9117-1:2009 | PAINTS AND VARNISHES - DRYING TESTS - PART 1: DETERMINATION OF THROUGH-DRY STATE AND THROUGH-DRY TIME |
| I.S. EN 61086-2:2004 | COATINGS FOR LOADED PRINTED WIRE BOARDS (CONFORMAL COATINGS) - PART 2: METHODS OF TEST |
| I.S. EN ISO 1518-1:2011 | PAINTS AND VARNISHES - DETERMINATION OF SCRATCH RESISTANCE - PART 1: CONSTANT-LOADING METHOD |
| I.S. EN ISO 2812-3:2012 | PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO LIQUIDS - PART 3: METHOD USING AN ABSORBENT MEDIUM (ISO 2812-3:2012) |
| EN ISO 15184:2012 | Paints and varnishes - Determination of film hardness by pencil test (ISO 15184:2012) |
| DIN EN ISO 2409:2013-06 | PAINTS AND VARNISHES - CROSS-CUT TEST (ISO 2409:2013) |
| DIN EN ISO 1522:2007-04 | Paints and varnishes - Pendulum damping test (ISO 1522:2006) |
| DIN EN ISO 2810:2004-10 | PAINTS AND VARNISHES - NATURAL WEATHERING OF COATINGS - EXPOSURE AND ASSESSMENT |
| BS EN ISO 2409:2013 | Paints and varnishes. Cross-cut test |
| ISO 3231:1993 | Paints and varnishes — Determination of resistance to humid atmospheres containing sulfur dioxide |
| ISO 7784-1:2016 | Paints and varnishes — Determination of resistance to abrasion — Part 1: Method with abrasive-paper covered wheels and rotating test specimen |
| BS EN ISO 11341:2004 | Paints and varnishes. Artificial weathering and exposure to artificial radiation. Exposure to filtered xenon-arc radiation |
| ISO 6860:2006 | Paints and varnishes Bend test (conical mandrel) |
| UNE-EN ISO 1522:2007 | Paints and varnishes - Pendulum damping test (ISO 1522:2006) |
| ONORM EN ISO 15184 : 2013 | PAINTS AND VARNISHES - DETERMINATION OF FILM HARDNESS BY PENCIL TEST (ISO 15184:2012) |
| BS EN ISO 3668:2001 | Paints and varnishes. Visual comparison of the colour of paints |
| BS EN ISO 15711:2004 | Paints and varnishes. Determination of resistance to cathodic disbonding of coatings exposed to sea water |
| BS EN ISO 12137-2:2006 | Paints and varnishes. Determination of mar resistance Method using a pointed stylus |
| BS EN 10301:2003 | Steel tubes and fittings for on and offshore pipelines. Internal coating for the reduction of friction for conveyance of non corrosive gas |
| BS EN ISO 7253:2001 | Paints and varnishes. Determination of resistance to neutral salt spray (fog) |
| ISO 9117-1:2009 | Paints and varnishes — Drying tests — Part 1: Determination of through-dry state and through-dry time |
| ISO 16474-3:2013 | Paints and varnishes Methods of exposure to laboratory light sources Part 3: Fluorescent UV lamps |
| ISO 12137-2:1997 | Paints and varnishes Determination of mar resistance Part 2: Method using a pointed stylus |
| BS EN ISO 20567-1:2017 | Paints and varnishes. Determination of stone-chip resistance of coatings Multi-impact testing |
| UNE-EN ISO 11997-2:2014 | Paints and varnishes - Determination of resistance to cyclic corrosion conditions - Part 2: Wet (salt fog)/dry/humidity/UV light (ISO 11997-2:2013) |
| BS EN ISO 1522:2006 | Paints and varnishes. Pendulum damping test |
| BS EN ISO 6272-2:2011 | Paints and varnishes. Rapid-deformation (impact resistance) tests Falling-weight test, small-area indenter |
| ISO 4623-2:2016 | Paints and varnishes Determination of resistance to filiform corrosion Part 2: Aluminium substrates |
| BS EN ISO 11507:2007 | Paints and varnishes. Exposure of coatings to artificial weathering. Exposure to fluorescent UV lamps and water |
| ISO 9117-5:2012 | Paints and varnishes — Drying tests — Part 5: Modified Bandow-Wolff test |
| ISO 4624:2016 | Paints and varnishes — Pull-off test for adhesion |
| IEC 60464-2:2001+AMD1:2006 CSV | Varnishes used for electrical insulation - Part 2: Methods of test |
| ISO 9117-6:2012 | Paints and varnishes — Drying tests — Part 6: Print-free test |
| BS EN ISO 1519:2011 | Paints and varnishes. Bend test (cylindrical mandrel) |
| UNE-EN ISO 7784-3:2016 | Paints and varnishes - Determination of resistance to abrasion - Part 3: Method with abrasive-paper covered wheel and linearly reciprocating test specimen (ISO 7784-3:2016) |
| ISO 14577-4:2016 | Metallic materials Instrumented indentation test for hardness and materials parameters Part 4: Test method for metallic and non-metallic coatings |
| UNE-EN ISO 20567-2:2017 | Paints and varnishes - Determination of stone-chip resistance of coatings - Part 2: Single-impact test with a guided impact body (ISO 20567-2:2017) |
| ISO 1519:2011 | Paints and varnishes Bend test (cylindrical mandrel) |
| ISO 11997-2:2013 | Paints and varnishes — Determination of resistance to cyclic corrosion conditions — Part 2: Wet (salt fog)/dry/humidity/UV light |
| ISO 6272:1993 | Paints and varnishes — Falling-weight test |
| ISO 15710:2002 | Paints and varnishes — Corrosion testing by alternate immersion in and removal from a buffered sodium chloride solution |
| ISO 12137:2011 | Paints and varnishes — Determination of mar resistance |
| ISO 9117-4:2012 | Paints and varnishes — Drying tests — Part 4: Test using a mechanical recorder |
| ISO 1518:1992 | Paints and varnishes Scratch test |
| ISO 9117-2:2010 | Paints and varnishes — Drying tests — Part 2: Pressure test for stackability |
| UNE-EN ISO 5659-2:2018 | Plastics - Smoke generation - Part 2: Determination of optical density by a single-chamber test (ISO 5659-2:2017) |
| ISO 20567-1:2017 | Paints and varnishes — Determination of stone-chip resistance of coatings — Part 1: Multi-impact testing |
| ISO 6272-2:2011 | Paints and varnishes — Rapid-deformation (impact resistance) tests — Part 2: Falling-weight test, small-area indenter |
| BS EN ISO 16862:2006 | Paints and varnishes. Evaluation of sag resistance |
| BS EN ISO 4624:2016 | Paints and varnishes. Pull-off test for adhesion |
| ISO 13803:2014 | Paints and varnishes — Determination of haze on paint films at 20° |
| ISO 3678:1976 | Paints and varnishes — Print-free test |
| ISO 1520:2006 | Paints and varnishes Cupping test |
| BS EN ISO 6270:1995 | Paints and varnishes. Determination of resistance to humidity (continuous condensation) |
| ISO 20567-3:2012 | Paints and varnishes — Determination of stone-chip resistance of coatings — Part 3: Single-impact test with a free-flying impact body |
| ISO 9117-3:2010 | Paints and varnishes — Drying tests — Part 3: Surface-drying test using ballotini |
| BS EN ISO 9227:2017 | Corrosion tests in artificial atmospheres. Salt spray tests |
| ISO 7784-2:2016 | Paints and varnishes — Determination of resistance to abrasion — Part 2: Method with abrasive rubber wheels and rotating test specimen |
| BS EN ISO 3248:2001 | Paints and varnishes. Determination of the effect of heat |
| BS EN ISO 13803:2014 | Paints and varnishes. Determination of haze on paint films at 20 degrees |
| ISO 11507:2007 | Paints and varnishes Exposure of coatings to artificial weathering Exposure to fluorescent UV lamps and water |
| ISO 16927:2014 | Paints and varnishes — Determination of the overcoatability and recoatability of a coating |
| UNE-EN ISO 2409:2013 | Paints and varnishes - Cross-cut test (ISO 2409:2013) |
| UNE-EN ISO 14577-4:2017 | Metallic materials - Instrumented indentation test for hardness and materials parameters - Part 4: Test method for metallic and non-metallic coatings (ISO 14577-4:2016) |
| ISO 7784-3:2016 | Paints and varnishes — Determination of resistance to abrasion — Part 3: Method with abrasive-paper covered wheel and linearly reciprocating test specimen |
| UNE-EN ISO 2812-1:2018 | Paints and varnishes - Determination of resistance to liquids - Part 1: Immersion in liquids other than water (ISO 2812-1:2017) |
| BS EN ISO 6860:2006 | Paints and varnishes. Bend test (conical mandrel) |
| DIN EN ISO 14577-4:2017-04 | METALLIC MATERIALS - INSTRUMENTED INDENTATION TEST FOR HARDNESS AND MATERIALS PARAMETERS - PART 4: TEST METHOD FOR METALLIC AND NON-METALLIC COATINGS (ISO 14577-4:2016) |
| EN ISO 20567-3:2012 | Paints and varnishes - Determination of stone-chip resistance of coatings - Part 3: Single-impact test with a free-flying impact body (ISO 20567-3:2012) |
| EN ISO 3248:2016 | Paints and varnishes - Determination of the effect of heat (ISO 3248:2016) |
| EN ISO 15711:2004 | Paints and varnishes - Determination of resistance to cathodic disbonding of coatings exposed to sea water (ISO 15711:2003) |
| EN ISO 9117-3:2010 | Paints and varnishes - Drying tests - Part 3: Surface-drying test using ballotini (ISO 9117-3:2010) |
| EN ISO 9117-4:2012 | Paints and varnishes - Drying tests - Part 4: Test using a mechanical recorder (ISO 9117-4:2012) |
| EN ISO 5659-2:2017 | Plastics - Smoke generation - Part 2: Determination of optical density by a single-chamber test (ISO 5659-2:2017) |
| EN ISO 7784-2:2016 | Paints and varnishes - Determination of resistance to abrasion - Part 2: Method with abrasive rubber wheels and rotating test specimen (ISO 7784-2:2016) |
| EN ISO 12137-1:2006 | Paints and varnishes - Determination of mar resistance - Part 1: Method using a curved stylus (ISO 12137-1:1997, including Technical Corrigendum 1:1998) |
| EN ISO 11997-2:2013 | Paints and varnishes - Determination of resistance to cyclic corrosion conditions - Part 2: Wet (salt fog)/dry/humidity/UV light (ISO 11997-2:2013) |
| EN ISO 1518-2:2011 | Paints and varnishes - Determination of scratch resistance - Part 2: Variable-loading method (ISO 1518-2:2011) |
| EN ISO 15710:2006 | Paints and varnishes - Corrosion testing by alternate immersion in and removal from a buffered sodium chloride solution (ISO 15710:2002) |
| EN ISO 20567-2:2017 | Paints and varnishes - Determination of stone-chip resistance of coatings - Part 2: Single-impact test with a guided impact body (ISO 20567-2:2017) |
| EN ISO 11341:2004 | Paints and varnishes - Artificial weathering and exposure to artificial radiation - Exposure to filtered xenon-arc radiation (ISO 11341:2004) |
| EN ISO 4623 : 1995 | PAINTS AND VARNISHES - FILIFORM CORROSION TEST ON STEEL |
| EN ISO 7784-1:2016 | Paints and varnishes - Determination of resistance to abrasion - Part 1: Method with abrasive-paper covered wheels and rotating test specimen (ISO 7784-1:2016) |
| EN ISO 1518:2000 | Paints and varnishes - Scratch test (ISO 1518:1992) |
| EN 29117 : 1992 | PAINTS AND VARNISHES - DETERMINATION OF THROUGH-DRY STATE AND THROUGH-DRY TIME - METHOD OF TEST |
| EN ISO 6272-2:2011 | Paints and varnishes - Rapid-deformation (impact resistance) tests - Part 2: Falling-weight test, small-area indenter (ISO 6272-2:2011) |
| EN ISO 9117-6:2012 | Paints and varnishes - Drying tests - Part 6: Print-free test (ISO 9117-6:2012) |
| EN ISO 20567-1:2017 | Paints and varnishes - Determination of stone-chip resistance of coatings - Part 1: Multi-impact testing (ISO 20567-1:2017) |
| EN ISO 9117-2:2010 | Paints and varnishes - Drying tests - Part 2: Pressure test for stackability (ISO 9117-2:2010) |
| EN ISO 4624:2016 | Paints and varnishes - Pull-off test for adhesion (ISO 4624:2016) |
| EN ISO 14577-4:2016 | Metallic materials - Instrumented indentation test for hardness and materials parameters - Part 4: Test method for metallic and non-metallic coatings (ISO 14577-4:2016) |
| EN 24624 : 1992 | PAINTS AND VARNISHES - PULL-OFF TEST |
| EN ISO 16862:2006 | Paints and varnishes - Evaluation of sag resistance (ISO 16862:2003) |
| EN ISO 3231:1997 | Paints and varnishes - Determination of resistance to humid atmospheres containing sulfur dioxide (ISO 3231:1993) |
| EN ISO 1520:2006 | Paints and varnishes - Cupping test (ISO 1520:2006) |
| EN ISO 1519:2011 | Paints and varnishes - Bend test (cylindrical mandrel) (ISO 1519:2011) |
| EN ISO 4622 : 1994 | PAINTS AND VARNISHES - PRESSURE TEST FOR STACKABILITY |
| EN ISO 2815:2003 | Paints and varnishes - Buchholz indentation test (ISO 2815:2003) |
| EN ISO 7253 : 2001 | PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO NEUTRAL SALT SPRAY (FOG) |
| EN ISO 12137-2:2006 | Paints and varnishes - Determination of mar resistance - Part 2: Method using a pointed stylus (ISO 12137-2:1997) |
| EN ISO 6272-1:2011 | Paints and varnishes - Rapid-deformation (impact resistance) tests - Part 1: Falling-weight test, large-area indenter (ISO 6272-1:2011) |
| EN ISO 11507:2007 | Paints and varnishes - Exposure of coatings to artificial weathering - Exposure to fluorescent UV lamps and water (ISO 11507:2007) |
| EN ISO 16927:2014 | Paints and varnishes - Determination of the overcoatability and recoatability of a coating (ISO 16927:2014) |
| EN ISO 3678:1995 | Paints and varnishes - Print-free test (ISO 3678:1976) |
| EN ISO 7784-3:2016 | Paints and varnishes - Determination of resistance to abrasion - Part 3: Method with abrasive-paper covered wheel and linearly reciprocating test specimen (ISO 7784-3:2016) |
| EN ISO 9117-1:2009 | Paints and varnishes - Drying tests - Part 1: Determination of through-dry state and through-dry time (ISO 9117-1:2009) |
| EN ISO 1518-1:2011 | Paints and varnishes - Determination of scratch resistance - Part 1: Constant-loading method (ISO 1518-1:2011) |
| DIN EN ISO 16927:2014-06 | PAINTS AND VARNISHES - DETERMINATION OF THE OVERCOATABILITY AND RECOATABILITY OF A COATING (ISO 16927:2014) |
| BS EN ISO 11997-1:2017 | Paints and varnishes. Determination of resistance to cyclic corrosion conditions Wet (salt fog)/dry/humid |
| I.S. EN ISO 11341:2004 | PAINTS AND VARNISHES - ARTIFICIAL WEATHERING AND EXPOSURE TO ARTIFICIAL RADIATION - EXPOSURE TO FILTERED XENON-ARC RADIATION |
| I.S. EN ISO 1518:2000 | PAINTS AND VARNISHES - SCRATCH TEST |
| I.S. EN 29117:1993 | PAINTS AND VARNISHES - DETERMINATION OF THROUGH-DRY STATE AND THROUGH-DRY TIME - METHOD OF TEST |
| 08/30189484 DC : DRAFT OCT 2008 | BS EN ISO 9117-2 - PAINTS AND VARNISHES - DRYING TESTS - PART 2: PRESSURE TEST FOR STACKABILITY |
| UNI EN ISO 9117-1 : 2009 | PAINTS AND VARNISHES - DRYING TESTS - PART 1: DETERMINATION OF THROUGH-DRY STATE AND THROUGH-DRY TIME |
| 17/30350881 DC : DRAFT SEP 2017 | BS ISO 14993 - CORROSION OF METALS AND ALLOYS - ACCELERATED TESTING INVOLVING CYCLIC EXPOSURE TO SALT MIST, DRY AND WET CONDITIONS |
| 10/30197383 DC : 0 | BS ISO 12013-1 - PAINTS AND VARNISHES - DETERMINATION OF CURING CHARACTERISTICS USING A FREE-DAMPED OSCILLATION METHOD - PART 1: START TEMPERATURE OF REACTION |
| ONORM EN ISO 2812-3 : 2012 | PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO LIQUIDS - PART 3: METHOD USING AN ABSORBENT MEDIUM (ISO 2812-3:2012) |
| AFAP-2 : 2010 | NATO REACTION-TO-FIRE TESTS FOR MATERIALS - SMOKE GENERATION |
| 96/120232 DC : DRAFT FEB 1996 | BS 3900-E20: METHODS OF TEST FOR PAINTS - DETERMINATION OF PENCIL HARDNESS |
| BS EN ISO 15110:2017 | Paints and varnishes. Artificial weathering including acidic deposition |
| 01/122232 DC : DRAFT JUNE 2001 | BS ISO 20340 - PAINTS AND VARNISHES - CORROSION PROTECTION OF STEEL STRUCTURES BY PROTECTIVE PAINT SYSTEMS - PERFORMANCE REQUIREMENTS FOR PROTECTIVE PAINT SYSTEMS FOR OFFSHORE AND RELATED STRUCTURES |
| DIN EN ISO 16474-3:2014-03 | Paints and varnishes - Methods of exposure to laboratory light sources - Part 3: Fluorescent UV lamps (ISO 16474-3:2013) |
| NF EN ISO 9117-3 : 2010 | PAINTS AND VARNISHES - DRYING TESTS - PART 3: SURFACE-DRYING TEST USING BALLOTINI |
| 14/30289470 DC : 0 | BS ISO 3668 - PAINTS AND VARNISHES - VISUAL COMPARISON OF THE COLOUR OF PAINTS |
| ISO 16151:2005 | Corrosion of metals and alloys Accelerated cyclic tests with exposure to acidified salt spray, "dry" and "wet" conditions |
| UNI EN ISO 8130-8 : 2011 | COATING POWDERS - PART 8: ASSESSMENT OF THE STORAGE STABILITY OF THERMOSETTING POWDERS |
| 10/30210872 DC : 0 | BS EN ISO 9117-5 - PAINTS AND VARNISHES - DRYING TESTS - PART 5: MODIFIED BANDOW-WOLFF TEST |
| BS EN ISO 17132:2007 | Paints and varnishes. T-bend test |
| BS 3900-E14(1997) : 1997 AMD 16870 | METHODS OF TEST FOR PAINTS - DETERMINATION OF RESISTANCE TO ABRASION (ROTATING ABRASIVE-PAPER-COVERED WHEEL) |
| BS ISO 12013-2:2012 | Paints and varnishes. Determination of curing characteristics using a free damped oscillation method Glass transition temperature |
| 11/30233262 DC : 0 | BS EN 1871 - ROAD MARKING MATERIALS - PAINT, THERMOPLASTIC AND COLD PLASTIC MATERIALS - SPECIFICATIONS |
| BS 3900-E19:1999 | Methods of test for paints Determination of film hardness by pencil test |
| BS ISO 20567-2 : 2005 AMD 16852 | PAINTS AND VARNISHES - DETERMINATION OF STONE-CHIP RESISTANCE OF COATINGS - PART 2: SINGLE-IMPACT TEST WITH A GUIDED IMPACT BODY |
| 02/123756 DC : DRAFT OCT 2002 | ISO 20567-1 - PAINTS AND VARNISHES - DETERMINATION OF STONE CHIP RESISTANCE OF COATINGS - PART 1: MULTI IMPACT TEST |
| UNE-EN ISO 12137:2012 | Paints and varnishes - Determination of mar resistance (ISO 12137:2011) |
| I.S. EN ISO 8130-12:2010 | COATING POWDERS - PART 12: DETERMINATION OF COMPATIBILITY |
| I.S. EN ISO 12137:2011 | PAINTS AND VARNISHES - DETERMINATION OF MAR RESISTANCE (ISO 12137:2011) |
| DIN EN ISO 8130-12:2011-02 | COATING POWDERS - PART 12: DETERMINATION OF COMPATIBILITY |
| I.S. EN ISO 2812-5:2007 | PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO LIQUIDS - PART 5: TEMPERATURE-GRADIENT OVEN METHOD |
| I.S. EN ISO 16927:2014 | PAINTS AND VARNISHES - DETERMINATION OF THE OVERCOATABILITY AND RECOATABILITY OF A COATING (ISO 16927:2014) |
| ISO 16474-1:2013 | Paints and varnishes — Methods of exposure to laboratory light sources — Part 1: General guidance |
| AEP-63 : 2009 | PERFORMANCE REQUIREMENTS FOR NON-SKID COATING SYSTEMS |
| UNI EN ISO 12137 : 2011 | PAINTS AND VARNISHES - DETERMINATION OF MAR RESISTANCE |
| EN ISO 4623-1:2002 | Paints and varnishes - Determination of resistance to filiform corrosion - Part 1: Steel substrates (ISO 4623-1:2000) |
| ISO 15110:2017 | Paints and varnishes — Artificial weathering including acidic deposition |
| EN ISO 2812-4:2017 | Paints and varnishes - Determination of resistance to liquids - Part 4: Spotting methods (ISO 2812-4:2017) |
| I.S. EN ISO 2812-1:2017 | PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO LIQUIDS - PART 1: IMMERSION IN LIQUIDS OTHER THAN WATER (ISO 2812-1:2017) |
| DIN EN ISO 2813:2015-02 | PAINTS AND VARNISHES - DETERMINATION OF GLOSS VALUE AT 20 DEGREES, 60 DEGREES AND 85 DEGREES (ISO 2813:2014) |
| BS EN ISO 6272-1:2011 | Paints and varnishes. Rapid-deformation (impact resistance) tests Falling-weight test, large-area indenter |
| ISO 1522:2006 | Paints and varnishes — Pendulum damping test |
| ISO 7253:1996 | Paints and varnishes — Determination of resistance to neutral salt spray (fog) |
| BS EN ISO 2815:2003 | Paints and varnishes. Buchholz indentation test |
| ISO 9227:2017 | Corrosion tests in artificial atmospheres — Salt spray tests |
| UNE-EN ISO 13803:2015 | Paints and varnishes - Determination of haze on paint films at 20º (ISO 13803:2014) |
| BS EN 1871:2000 | Road marking materials. Physical properties |
| BS EN 1825-1:2004 | Grease separators Principles of design, performance and testing, marking and quality control |
| BS EN ISO 14577-4:2016 | Metallic materials. Instrumented indentation test for hardness and materials parameters Test method for metallic and non-metallic coatings |
| ISO 5659-2:2017 | Plastics — Smoke generation — Part 2: Determination of optical density by a single-chamber test |
| BS EN 24624:1993 | Paints and varnishes. Pull-off test |
| ISO 20567-2:2017 | Paints and varnishes — Determination of stone-chip resistance of coatings — Part 2: Single-impact test with a guided impact body |
| BS EN ISO 4623-2:2004 | Paints and varnishes. Determination of resistance to filiform corrosion Aluminium substrates |
| BS EN 858-1:2002 | Separator systems for light liquids (e.g. oil and petrol) Principles of product design, performance and testing, marking and quality control |
| ISO 8130-8:1994 | Coating powders Part 8: Assessment of the storage stability of thermosetting powders |
| DIN ISO 8130-8:2005-03 | COATING POWDERS - PART 8: ASSESSMENT OF THE STORAGE STABILITY OF THERMOSETTING POWDERS |
| DIN EN ISO 9227:2017-07 | Corrosion tests in artificial atmospheres - Salt spray tests (ISO 9227:2017) |
| EN 60464-2:2001/A1:2006 | VARNISHES USED FOR ELECTRICAL INSULATION - PART 2: METHODS OF TEST |
| EN 13062:2003 | Products and systems for the protection and repair of concrete structure - Test method - Determination of thixotropy of products for protection of reinforcement |
| DIN EN ISO 4624:2016-08 | Paints and varnishes - Pull-off test for adhesion (ISO 4624:2016) |
| DIN EN ISO 1518-1:2011-09 | PAINTS AND VARNISHES - DETERMINATION OF SCRATCH RESISTANCE - PART 1: CONSTANT-LOADING METHOD (ISO 1518-1:2011) |
| DIN EN ISO 15711:2005-03 | Paints and varnishes - Determination of resistance to cathodic disbonding of coatings exposed to sea water (ISO 15711:2003) |
| DIN EN ISO 15710:2006-09 | Paints and varnishes - Corrosion testing by alternate immersion in and removal from a buffered sodium chloride solution (ISO 15710:2002) |
| DIN EN 1825-1:2004-12 | Grease separators - Part 1: Principles of design, performance and testing, marking and quality control; German version EN 1825-1:2004 |
| DIN EN ISO 15184:2013-02 | PAINTS AND VARNISHES - DETERMINATION OF FILM HARDNESS BY PENCIL TEST (ISO 15184:2012) |
| BS 3900-E10(2003) : 2003 | PAINTS AND VARNISHES - PULL-OFF TEST FOR ADHESION |
| BS 3900-F8(1993) : 1993 AMD 9930 | METHODS OF TEST FOR PAINTS - DETERMINATION OF RESISTANCE TO HUMID ATMOSPHERES CONTAINING SULFUR DIOXIDE |
| BS 3900-F13(2002) : 2002 | PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO FILIFORM CORROSION - PART 1: STEEL SUBSTRATES |
| BS 3900-C3(1990) : AMD 7501 | METHODS OF TEST FOR PAINTS - THROUGH DRY TEST |
| BS 3900-E4(2001) : 2001 | PAINTS AND VARNISHES - CUPPING TEST |
| BS 3900-E6(1992) : 1992 AMD 8353 | METHODS OF TEST FOR PAINTS - CROSS CUT TEST |
| BS 3900-J4(1995) : 1995 | METHODS OF TEST FOR PAINTS - DETERMINATION OF THE STORAGE STABILITY OF COATING POWDERS |
| BS 3900-E6(2007) : 2007 | PAINTS AND VARNISHES - CROSS-CUT TEST |
| BS 3900-E2(1992) : 1992 AMD 12091 | METHODS OF TEST FOR PAINTS - SCRATCH TEST |
| NACE AMPP SP21417:2023 | Performance Requirements for Navy Ships Exterior Topside Coatings |
| BS 3900-E1(2002) : 2002 | PAINTS AND VARNISHES - BEND TEST (CYLINDRICAL MANDREL) |
| BS 3900-E1(1995) : 1995 | METHODS OF TEST FOR PAINTS - MECHANICAL TESTS ON PAINT FILMS - PAINTS AND VARNISHES - BEND TEST (CYLINDRICAL MANDREL) |
| BS 3900-G5(1993) : 1993 AMD 8355 | METHODS OF TEST FOR PAINTS - DETERMINATION OF RESISTANCE TO LIQUIDS - GENERAL METHODS |
| BS 3900-C2(1994) : 1994 AMD 8609 | METHODS OF TEST FOR PAINTS - SURFACE-DRYING TEST (BALLOTINI METHOD) |
| BS 3900-E4(1995) : 1995 | METHODS OF TEST FOR PAINTS - MECHANICAL TESTS ON PAINT FILMS - PAINTS AND VARNISHES - CUPPING TEST |
| EN 520:2004+A1:2009 | Gypsum plasterboards - Definitions, requirements and test methods |
| ISO 4287:1997 | Geometrical Product Specifications (GPS) — Surface texture: Profile method — Terms, definitions and surface texture parameters |
| ISO 8501-1:2007 | Preparation of steel substrates before application of paints and related products — Visual assessment of surface cleanliness — Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings |
| ISO 2808:2007 | Paints and varnishes Determination of film thickness |
| EN 13523-0:2014 | Coil coated metals - Test methods - Part 0: General introduction |
| EN 1396:2015 | Aluminium and aluminium alloys - Coil coated sheet and strip for general applications - Specifications |
| EN 10346:2015 | Continuously hot-dip coated steel flat products for cold forming - Technical delivery conditions |
| EN 16245-1:2013 | Fibre-reinforced plastic composites - Declaration of raw material characteristics - Part 1: General requirements |
| EN 10205:2016 | Cold reduced tinmill products - Blackplate |
| EN 15283-2:2008+A1:2009 | Gypsum boards with fibrous reinforcement - Definitions, requirements and test methods - Part 2: Gypsum fibre boards |
| EN 13523-22:2017 | Coil coated metals - Test methods - Part 22: Colour difference - Visual comparison |
| EN 13523-1:2017 | Coil coated metals - Test methods - Part 1: Film thickness |
| ISO 8336:2017 | Fibre-cement flat sheets — Product specification and test methods |
| ISO 11949:2016 | Cold-reduced tinmill products Electrolytic tinplate |
| ISO 8504-2:2000 | Preparation of steel substrates before application of paints and related products Surface preparation methods Part 2: Abrasive blast-cleaning |
| ISO 2409:2013 | Paints and varnishes Cross-cut test |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.