EN 1090-2:2008+A1:2011
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Execution of steel structures and aluminium structures - Part 2: Technical requirements for steel structures
Superseded date
14-06-2019
Superseded by
Published date
03-08-2011
Publisher
Sorry this product is not available in your region.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Specifications and documentation
5 Constituent products
6 Preparation and assembly
7 Welding
8 Mechanical fastening
9 Erection
10 Surface treatment
11 Geometrical tolerances
12 Inspection, testing and correction
Annex A (normative) - Additional information, list of
options and requirements related to the execution
classes
Annex B (informative) - Guidance for the determination
of execution classes
Annex C (informative) - Check-list for the content of a
quality plan
Annex D (normative) - Geometrical tolerances
Annex E (informative) - Welded joints in hollow sections
Annex F (normative) - Corrosion protection
Annex G (normative) - Test to determine slip factor
Annex H (normative) - Calibration test for preloaded
bolts under site conditions
Annex J (normative) - Use of compressible washer-type
direct tension indicators
Annex K (informative) - Hexagon injection bolts
Annex L (informative) - Guide to flow diagram for
development and use of a WPS
Annex M (normative) - Sequential method for fasteners
inspection
Bibliography
This European Standard specifies requirements for execution of structural steelwork as structures or as manufactured components, produced from:-hot rolled, structural steel products up to and including grade S690;-cold formed components and sheeting up to and including grades S700;-hot finished and cold formed austenitic, austenitic-ferritic and ferritic stainless steel products;-hot finished and cold formed structural hollow sections, including standard range and custom-made rolled products and hollow sections manufactured by welding.This European Standard may also be used for structural steel grades up to and including S960, provided that conditions for execution are verified against reliability criteria and any necessary additional requirements are specified.This European Standard specifies requirements independent of the type and shape of the steel structure (e.g. buildings, bridges, plated or latticed components) including structures subjected to fatigue or seismic actions. The requirements are expressed in terms of execution classesThis European Standard applies to structures designed according to the relevant part of EN 1993.This European Standard applies to structural components and sheeting as defined in EN 1993-1-3.This European Standard applies to steel components in composite steel and concrete structures designed according to the relevant part of EN 1994.This European Standard may be used for structures designed according to other design rules provided that conditions for execution comply with them and any necessary additional requirements are specified.This European Standard does not cover requirements for watertightness or air permeability resistance of sheeting.
| Committee |
CEN/TC 135
|
| DevelopmentNote |
Supersedes ENV 1090-1, ENV 1090-2, ENV 1090-3, ENV 1090-4, ENV 1090-5 and ENV 1090-6. (09/2008) 2008 Edition Re-issued in August 2011 & incorporates AMD 1 2011. (08/2011)
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| UNE-EN 1090-2:2019 | Identical |
| DIN EN 1090-2:2011-10 | Identical |
| ONORM EN 1090-2 : 2012 | Identical |
| I.S. EN 1090-2:2018 | Identical |
| I.S. EN 1090-2:2008 | Identical |
| PN EN 1090-2 : 2009 + A1 2012 | Identical |
| BS EN 1090-2 : 2008 | Identical |
| NEN EN 1090-2 : 2008 + A1 2011 | Identical |
| UNI EN 1090-2:2018 | Identical |
| NEN EN 1090-2:2018 | Identical |
| BS EN 1090-2:2018 | Identical |
| SN EN 1090-2 : 2008 + A1 2011 | Identical |
| UNI EN 1090-2 : 2011 | Identical |
| NS EN 1090-2:2018 | Identical |
| NBN EN 1090-2 : 2009 + A1 2011 | Identical |
| DIN EN 1090-2:2015-07 (Draft) | Identical |
| NS EN 1090-2 : 2008 + A1 2011 | Identical |
| UNE-EN 1090-2:2011 | Identical |
| NF EN 1090-2 : 2009 + A1 2011 | Identical |
| ÖNORM EN 1090-2:2018 | Identical |
| DIN EN 1090-2:2018-09 | Identical |
| DS EN 1090-2 : 2008 + A1 2011 | Identical |
| BS EN 1090-2:2008+A1:2011 | Identical |
| UNE-EN 1090-2:2011+A1:2011 | Identical |
| PD CEN/TR 17052:2017 | Guidelines on implementing EN 1090-1:2009+A1:2011, Execution of steel structures and aluminium structures Requirements for conformity assessment of structural components |
| 14/30304786 DC : 0 | BS EN 15048-2 - NON-PRELOADED STRUCTURAL BOLTING ASSEMBLIES - PART 2: FITNESS FOR PURPOSE |
| PREN 14199 : DRAFT 2013 | EXECUTION OF SPECIAL GEOTECHNICAL WORK - MICROPILES |
| UNE-EN 15129:2011 | Anti-seismic devices |
| UNI EN 1090-3 : 2008 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 3: TECHNICAL REQUIREMENTS FOR ALUMINIUM STRUCTURES |
| S.R. CEN/TR 1317-6:2012 | ROAD RESTRAINT SYSTEMS - PART 6: PEDESTRIAN RESTRAINT SYSTEM - PEDESTRIAN PARAPETS |
| 13/30280743 DC : 0 | BS EN 14199 - EXECUTION OF SPECIAL GEOTECHNICAL WORK - MICROPILES |
| 13/30277440 DC : 0 | BS EN 14399-6 - HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 6: PLAIN CHAMFERED WASHERS |
| UNE-EN 1993-1-8:2013 | Eurocode 3: Design of steel structures - Part 1-8: Design of joints |
| VDMA 24408 : DRAFT 2015 | LIMIT OF THE SCOPE OF THE EUROPEAN CONSTRUCTION PRODUCTS REGULATION 305/2011/EU WITH RESPECT TO PROCESS PLANT AND AMENDMENTS TO HARMONIZED STANDARDS UNDER THE EUROPEAN PRESSURE EQUIPMENT DIRECTIVE |
| PREN 14399-8 : DRAFT 2015 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 8: SYSTEM HV - HEXAGON FIT BOLT AND NUT ASSEMBLIES |
| UNE-EN 1994-1-1:2013 | Eurocode 4: Design of composite steel and concrete structures - Part 1-1: General rules and rules for buildings |
| I.S. EN 74-2:2008 | COUPLERS, SPIGOT PINS AND BASEPLATES FOR USE IN FALSEWORK AND SCAFFOLDS - PART 2: SPECIAL COUPLERS - REQUIREMENTS AND TEST PROCEDURES |
| BS EN 1993-4-2 : 2007 | EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 4-2: TANKS |
| I.S. EN 1993-4-1:2007 | EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 4-1: SILOS |
| UNE-EN 1998-1:2011 | Eurocode 8: Design of structures for earthquake resistance - Part 1: General rules, seismic actions and rules for buildings |
| UNI EN 74-2 : 2009 | COUPLERS, SPIGOT PINS AND BASEPLATES FOR USE IN FALSEWORK AND SCAFFOLDS - PART 2: SPECIAL COUPLERS - REQUIREMENTS AND TEST PROCEDURES |
| UNE-EN 74-2:2010 | Couplers, spigot pins and baseplates for use in falsework and scaffolds - Part 2: Special couplers - Requirements and test procedures |
| DIN EN 15129:2010-06 | ANTI-SEISMIC DEVICES |
| DIN EN 1090-3:2008-09 | EXECUTION OF STEEL AND ALUMINIUM STRUCTURES - PART 3: TECHNICAL RULES FOR EXECUTION OF ALUMINIUM STRUCTURES |
| ONORM EN 1090-3 : 2008 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 3: TECHNICAL REQUIREMENTS FOR ALUMINIUM STRUCTURES |
| UNI EN 1090-1 : 2012 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 1: REQUIREMENTS FOR CONFORMITY ASSESSMENT OF STRUCTURAL COMPONENTS |
| EN 15048-1:2016 | Non-preloaded structural bolting assemblies - Part 1: General requirements |
| DIN EN 1994-1-1:2010-12 | Eurocode 4: Design of composite steel and concrete structures - Part 1-1: General rules and rules for buildings (includes Corrigendum AC:2009) |
| DIN EN 14399-2:2015-04 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 2: SUITABILITY FOR PRELOADING |
| BS EN 12699:2015 | Execution of special geotechnical works. Displacement piles |
| BS EN 1993-1-4 : 2006 | EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 1-4: GENERAL RULES - SUPPLEMENTARY RULES FOR STAINLESS STEELS |
| I.S. EN 12699:2015 | EXECUTION OF SPECIAL GEOTECHNICAL WORKS - DISPLACEMENT PILES |
| EN 13084-7:2012 | Free-standing chimneys - Part 7: Product specifications of cylindrical steel fabrications for use in single wall steel chimneys and steel liners |
| DIN EN 1993-6:2010-12 | Eurocode 3: Design of steel structures - Part 6: Crane supporting structures (includes Corrigendum AC:2009) |
| CEN/TR 17052:2017 | Guidelines on implementing EN 1090-1:2009+A1:2011, Execution of steel structures and aluminium structures - Part 1: Requirements for conformity assessment of structural components |
| CEN/TR 1317-6:2012 | Road restraint systems - Part 6: Pedestrian restraint system - Pedestrian parapets |
| EN 1090-1:2009+A1:2011 | Execution of steel structures and aluminium structures - Part 1: Requirements for conformity assessment of structural components |
| EN 12812:2008 | Falsework - Performance requirements and general design |
| DIN EN 16031:2012-09 | ADJUSTABLE TELESCOPIC ALUMINUM PROPS - PRODUCT SPECIFICATIONS, DESIGN AND ASSESSMENT BY CALCULATION AND TESTS |
| 13/30277434 DC : 0 | BS EN 14399-4 - HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 4: SYSTEM HV - HEXAGON BOLT AND NUT ASSEMBLIES |
| I.S. EN 1090-3:2008 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 3: TECHNICAL REQUIREMENTS FOR ALUMINIUM STRUCTURES |
| PREN 1090-3 : DRAFT 2017 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 3: TECHNICAL REQUIREMENTS FOR ALUMINIUM STRUCTURES |
| 13/30277428 DC : 0 | BS EN 14399-2 - HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 2: SUITABILITY TEST FOR PRELOADING |
| BS EN 1090-1 : 2009 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 1: REQUIREMENTS FOR CONFORMITY ASSESSMENT OF STRUCTURAL COMPONENTS |
| UNE-EN 15048-1:2018 | Non-preloaded structural bolting assemblies - Part 1: General requirements |
| BS EN 16031:2012 | Adjustable telescopic aluminium props. Product specifications, design and assessment by calculation and tests |
| 07/30166055 DC : 0 | BS EN 14399-10 - HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 10: SYSTEM HRC - BOLT AND NUT ASSEMBLIES WITH CALIBRATED PRELOAD |
| PREN 14399-2 : DRAFT 2013 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 2: SUITABILITY TEST FOR PRELOADING |
| PD CEN/TR 16949:2016 | Road restraint system. Pedestrian restraint system. Pedestrian parapets |
| UNE-EN 1090-1:2011 | Execution of steel structures and aluminium structures - Part 1: Requirements for conformity assessment of structural components |
| CEN/TR 16949:2016 | Road restraint system - Pedestrian restraint system - Pedestrian parapets |
| PREN 14399-5 : DRAFT 2013 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 5: PLAIN WASHERS |
| BS EN 16681:2016 | Steel static storage systems. Adjustable pallet racking systems. Principles for seismic design |
| UNI EN 14399-9 : 2009 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 9: SYSTEM HR OR HV - DIRECT TENSION INDICATORS FOR BOLT AND NUT ASSEMBLIES |
| I.S. EN 14399-10:2009 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 10: SYSTEM HRC - BOLT AND NUT ASSEMBLIES WITH CALIBRATED PRELOAD |
| PREN 13107 : DRAFT 2013 | SAFETY REQUIREMENTS FOR CABLEWAY INSTALLATIONS DESIGNED TO CARRY PERSONS - CIVIL ENGINEERING WORKS |
| S.R. CEN/TR 17052:2017 | GUIDELINES ON IMPLEMENTING EN 1090-1:2009+A1:2011, EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 1: REQUIREMENTS FOR CONFORMITY ASSESSMENT OF STRUCTURAL COMPONENTS |
| UNI CEN/TR 1317-6 : 2012 | ROAD RESTRAINT SYSTEMS - PART 6: PEDESTRIAN RESTRAINT SYSTEM - PEDESTRIAN PARAPETS |
| UNE-EN 14399-1:2016 | High-strength structural bolting assemblies for preloading - Part 1: General requirements |
| UNE-EN 14399-4:2016 | High-strength structural bolting assemblies for preloading - Part 4: System HV - Hexagon bolt and nut assemblies |
| UNE-EN 1994-2:2013 | Eurocode 4 - Design of composite steen and concrete structures - Part 2: General rules and rules for bridges |
| 16/30328759 DC : 0 | BS EN 13814-1 - SAFETY OF AMUSEMENT RIDES AND AMUSEMENT DEVICES - PART 1: DESIGN AND MANUFACTURE |
| I.S. EN 1993-1-6:2007 | EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 1-6: STRENGTH AND STABILITY OF SHELL STRUCTURES |
| I.S. EN 15048-1:2016 | NON-PRELOADED STRUCTURAL BOLTING ASSEMBLIES - PART 1: GENERAL REQUIREMENTS |
| UNE-EN 14399-6:2016 | High-strength structural bolting assemblies for preloading - Part 6: Plain chamfered washers |
| PREN 17206 : DRAFT 2018 | ENTERTAINMENT TECHNOLOGY - LIFTING AND LOAD-BEARING EQUIPMENT FOR STAGES AND OTHER PRODUCTION AREAS WITHIN THE ENTERTAINMENT INDUSTRY - SPECIFICATIONS FOR GENERAL REQUIREMENTS (EXCLUDING ALUMINUM AND STEEL TRUSSES AND TOWERS) |
| PREN 14399-10 : DRAFT 2015 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 10: SYSTEM HRC - BOLT AND NUT ASSEMBLIES WITH CALIBRATED PRELOAD |
| BS EN 15129:2009 | Anti-seismic devices |
| UNE-EN 15048-2:2017 | Non-preloaded structural bolting assemblies - Part 2: Fitness for purpose |
| UNI EN 14399-10 : 2009 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 10: SYSTEM HRC - BOLT AND NUT ASSEMBLIES WITH CALIBRATED PRELOAD |
| UNI EN 15129 : 2009 | ANTI-SEISMIC DEVICES |
| UNE-EN 1993-1-3:2012 | Eurocode 3 - Design of steel structures - Part 1-3: General rules - Supplementary rules for cold-formed members and sheeting |
| DIN EN 14399-9:2016-01 (Draft) | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 9: SYSTEM HR OR HV - DIRECT TENSION INDICATORS FOR BOLT AND NUT ASSEMBLIES |
| EN 14399-10:2018 | High-strength structural bolting assemblies for preloading - Part 10: System HRC - Bolt and nut assemblies with calibrated preload |
| DIN EN 12699:2015-07 | EXECUTION OF SPECIAL GEOTECHNICAL WORKS - DISPLACEMENT PILES |
| DIN EN 1993-4-3:2010-12 | EUROCODE 3: DESIGN OF STEEL STRUCTURES - PART 4-3: PIPELINES |
| DIN EN 13107:2015-09 | SAFETY REQUIREMENTS FOR CABLEWAY INSTALLATIONS DESIGNED TO CARRY PERSONS - CIVIL ENGINEERING WORKS |
| DIN EN 13084-7:2013-03 | FREE-STANDING CHIMNEYS - PART 7: PRODUCT SPECIFICATIONS OF CYLINDRICAL STEEL FABRICATIONS FOR USE IN SINGLE WALL STEEL CHIMNEYS AND STEEL LINERS |
| DIN EN 1993-1-3:2010-12 | Eurocode 3: Design of steel structures - Part 1-3: General rules - Supplementary rules for cold-formed members and sheeting (includes Corrigendum AC:2009) |
| DIN EN 1993-1-8:2010-12 | Eurocode 3: Design of steel structures - Part 1-8: Design of joints (includes Corrigendum AC:2009) |
| DIN EN 14199:2015-07 | Execution of special geotechnical work - Micropiles; German version EN 14199:2015 |
| BS EN 14399-5 : 2015-02 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 5: PLAIN WASHERS |
| BS EN 1991-3:2006 | Eurocode 1. Actions on structures Actions induced by cranes and machinery |
| BS EN 15048-1:2007 | Non-preloaded structural bolting assemblies General requirements |
| BS EN 14399-1:2015 | High-strength structural bolting assemblies for preloading General requirements |
| I.S. EN 14399-3:2015 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 3: SYSTEM HR - HEXAGON BOLT AND NUT ASSEMBLIES |
| I.S. EN 14399-4:2015 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 4: SYSTEM HV - HEXAGON BOLT AND NUT ASSEMBLIES |
| DIN EN 1993-1-6:2010-12 | EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 1-6: STRENGTH AND STABILITY OF SHELL STRUCTURES |
| I.S. EN 1994-2:2005 | EUROCODE 4 - DESIGN OF COMPOSITE STEEL AND CONCRETE STRUCTURES - PART 2: GENERAL RULES AND RULES FOR BRIDGES (INCLUDING IRISH NATIONAL ANNEX) |
| I.S. EN 12812:2008 | FALSEWORK - PERFORMANCE REQUIREMENTS AND GENERAL DESIGN |
| I.S. EN 14399-6:2015 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 6: PLAIN CHAMFERED WASHERS |
| I.S. EN 1994-1-1:2005 | EUROCODE 4: DESIGN OF COMPOSITE STEEL AND CONCRETE STRUCTURES - PART 1-1: GENERAL RULES AND RULES FOR BUILDINGS (INCLUDING IRISH NATIONAL ANNEX) |
| I.S. EN 14399-5:2015 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 5: PLAIN WASHERS |
| I.S. EN 13084-7:2012 | FREE-STANDING CHIMNEYS - PART 7: PRODUCT SPECIFICATIONS OF CYLINDRICAL STEEL FABRICATIONS FOR USE IN SINGLE WALL STEEL CHIMNEYS AND STEEL LINERS |
| I.S. EN 13107:2015 | SAFETY REQUIREMENTS FOR CABLEWAY INSTALLATIONS DESIGNED TO CARRY PERSONS - CIVIL ENGINEERING WORKS |
| I.S. EN 15048-2:2016 | NON-PRELOADED STRUCTURAL BOLTING ASSEMBLIES - PART 2: FITNESS FOR PURPOSE |
| DIN EN 14399-3:2015-04 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 3: SYSTEM HR - HEXAGON BOLT AND NUT ASSEMBLIES |
| I.S. EN 14399-2:2015 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 2: SUITABILITY FOR PRELOADING |
| I.S. EN 14199:2015 | EXECUTION OF SPECIAL GEOTECHNICAL WORKS - MICROPILES |
| I.S. EN 14399-1:2015 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 1: GENERAL REQUIREMENTS |
| VDI 3576:2011-03 | Rails for crane systems - Rail connections, rail beddings, rail fastenings, tolerances for crane tracks |
| 09/30211977 DC : 0 | BS EN 16031 - ADJUSTABLE TELESCOPIC ALUMINIUM PROPS - PRODUCT SPECIFICATIONS, DESIGN AND ASSESSMENT BY CALCULATION AND TESTS |
| PD CEN/TR 1317-6:2012 | Road restraint systems Pedestrian restraint system. Pedestrian parapets |
| I.S. EN 1991-3:2006 | EUROCODE 1 - ACTIONS ON STRUCTURES - PART 3: ACTIONS INDUCED BY CRANES AND MACHINERY |
| DIN EN 14399-10:2016-01 (Draft) | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 10: SYSTEM HRC - BOLT AND NUT ASSEMBLIES WITH CALIBRATED PRELOAD |
| 13/30277437 DC : 0 | BS EN 14399-5 - HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 5: PLAIN WASHERS |
| 11/30247279 DC : 0 | BS EN 1337-1 - STRUCTURAL BEARINGS - PART 1: GENERAL |
| 13/30277431 DC : 0 | BS EN 14399-3 - HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 3: SYSTEM HR - HEXAGON BOLT AND NUT ASSEMBLIES |
| ISO/TS 20273:2017 | Guidelines on weld quality in relationship to fatigue strength |
| PREN 14399-9 : DRAFT 2015 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 9: SYSTEM HR OR HV - DIRECT TENSION INDICATORS FOR BOLT AND NUT ASSEMBLIES |
| 13/30275585 DC : 0 | BS EN 13107 - SAFETY REQUIREMENTS FOR CABLEWAY INSTALLATIONS DESIGNED TO CARRY PERSONS - CIVIL ENGINEERING WORKS |
| BS EN 74-2:2008 | Couplers, spigot pins and baseplates for use in falsework and scaffolds Special couplers. Requirements and test procedures |
| 15/30332551 DC : 0 | BS EN 14399-10 - HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 10: SYSTEM HRC - BOLT AND NUT ASSEMBLIES WITH CALIBRATED PRELOAD |
| PREN 14399-3 : DRAFT 2013 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 3: SYSTEM HR - HEXAGON BOLT AND NUT ASSEMBLIES |
| PREN 14399-6 : DRAFT 2013 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 6: PLAIN CHAMFERED WASHERS |
| 17/30347025 DC : 0 | BS EN 15129 - ANTI-SEISMIC DEVICES |
| EN 15129:2018 | Anti-seismic devices |
| PREN 12699 : DRAFT 2013 | EXECUTION OF SPECIAL GEOTECHNICAL WORK - DISPLACEMENT PILES |
| PREN 1090-4 : DRAFT 2014 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 4: TECHNICAL REQUIREMENTS FOR THIN-GAUGE, COLD-FORMED STEEL ELEMENTS AND STRUCTURES FOR ROOF, CEILING, FLOOR AND WALL APPLICATIONS |
| EN 1090-3:2008 | Execution of steel structures and aluminium structures - Part 3: Technical requirements for aluminium structures |
| DIN EN 12812:2008-12 | FALSEWORK - PERFORMANCE REQUIREMENTS AND GENERAL DESIGN |
| DIN EN 1993-1-4:2015-10 | EUROCODE 3: DESIGN OF STEEL STRUCTURES - PART 1-4: GENERAL RULES - SUPPLEMENTARY RULES FOR STAINLESS STEELS |
| DIN EN 1994-2:2010-12 | Eurocode 4: Design of composite steel and concrete structures - Part 2: General rules and rules for bridges (includes Corrigendum AC:2008) |
| BS EN 1993-4-3:2007 | Eurocode 3. Design of steel structures Pipelines |
| BS EN 1993-1-3:2006 | Eurocode 3. Design of steel structures General rules - Supplementary rules for cold-formed members and sheeting |
| EEMUA 207 : 2009 | DOUBLE CONCRETE TANKS FOR LIQUEFIED GAS - GUIDE TO DESIGN, CONSTRUCTION AND OPERATION |
| UNI EN 13084-7 : 2013 | FREE-STANDING CHIMNEYS - PART 7: PRODUCT SPECIFICATIONS OF CYLINDRICAL STEEL FABRICATIONS FOR USE IN SINGLE WALL STEEL CHIMNEYS AND STEEL LINERS |
| UNI EN 1993-5 : 2007 | EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 5: PILING |
| ONORM EN 74-2 : 2009 | COUPLERS, SPIGOT PINS AND BASEPLATES FOR USE IN FALSEWORK AND SCAFFOLDS - PART 2: SPECIAL COUPLERS - REQUIREMENTS AND TEST PROCEDURES |
| UNI EN 1994-2 : 2006 | EUROCODE 4 - DESIGN OF COMPOSITE STEEL AND CONCRETE STRUCTURES - PART 2: GENERAL RULES AND RULES FOR BRIDGES |
| UNI EN 1993-1-3 : 2007 | EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 1-3: GENERAL RULES - SUPPLEMENTARY RULES FOR COLD-FORMED MEMBERS AND SHEETING |
| UNI EN 1993-4-3 : 2007 | EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 4-3: PIPELINES |
| UNI EN 1993-1-8 : 2005 | EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 1-8: DESIGN OF JOINTS |
| UNI EN 1993-1-9 : 2005 | EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 1-9: FATIGUE |
| UNI EN 1993-6 : 2007 | EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 6: CRANE SUPPORTING STRUCTURES |
| UNI EN 12812 : 2008 | FALSEWORK - PERFORMANCE REQUIREMENTS AND GENERAL DESIGN |
| UNI EN 1994-1-1 : 2005 | EUROCODE 4 - DESIGN OF COMPOSITE STEEL AND CONCRETE STRUCTURES - PART 1-1: GENERAL RULES AND RULES FOR BUILDINGS |
| UNI EN 1991-3 : 2006 | EUROCODE 1 - ACTIONS ON STRUCTURES - PART 3: ACTIONS INDUCED BY CRANES AND MACHINERY |
| UNI EN 1993-1-1 : 2014 | EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 1-1: GENERAL RULES AND RULES FOR BUILDINGS |
| I.S. EN 16031:2012 | ADJUSTABLE TELESCOPIC ALUMINIUM PROPS - PRODUCT SPECIFICATIONS, DESIGN AND ASSESSMENT BY CALCULATION AND TESTS |
| DIN EN 1993-4-2:2017-09 | EUROCODE 3: DESIGN OF STEEL STRUCTURES - PART 4-2: TANKS |
| PD ISO/TS 20273:2017 | Guidelines on weld quality in relationship to fatigue strength |
| PREN 15048-2 : DRAFT 2014 | NON-PRELOADED STRUCTURAL BOLTING ASSEMBLIES - PART 2: FITNESS FOR PURPOSE |
| UNI EN 16031 : 2012 | ADJUSTABLE TELESCOPIC ALUMINIUM PROPS - PRODUCT SPECIFICATIONS, DESIGN AND ASSESSMENT BY CALCULATION AND TESTS |
| UNE-EN 14399-5:2016 | High-strength structural bolting assemblies for preloading - Part 5: Plain washers |
| 15/30332548 DC : 0 | BS EN 14399-8 - HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 8: SYSTEM HV - HEXAGON FIT BOLT AND NUT ASSEMBLIES |
| 14/30297831 DC : 0 | BS EN 1090-4 - EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 4: TECHNICAL REQUIREMENTS FOR THIN-GAUGE, COLD-FORMED STEEL ELEMENTS AND STRUCTURES FOR ROOF, CEILING, FLOOR AND WALL APPLICATIONS |
| 17/30348949 DC : 0 | BS EN 1090-3 - EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 3: TECHNICAL REQUIREMENTS FOR ALUMINIUM STRUCTURES |
| BS EN 14399-10:2009 | High-strength structural bolting assemblies for preloading System HRC. Bolt and nut assemblies with calibrated preload |
| PREN 13031-1 : DRAFT 2017 | GREENHOUSES - DESIGN AND CONSTRUCTION - PART 1: COMMERCIAL PRODUCTION GREENHOUSES |
| I.S. EN 16681:2016 | STEEL STATIC STORAGE SYSTEMS - ADJUSTABLE PALLET RACKING SYSTEMS - PRINCIPLES FOR SEISMIC DESIGN |
| DIN EN 1998-1:2010-12 | Eurocode 8: Design of structures for earthquake resistance - Part 1: General rules, seismic actions and rules for buildings (includes Corrigendum AC:2009) |
| DIN EN 15048-1:2016-09 | NON-PRELOADED STRUCTURAL BOLTING ASSEMBLIES - PART 1: GENERAL REQUIREMENTS |
| DIN EN 15048-2:2016-09 | NON-PRELOADED STRUCTURAL BOLTING ASSEMBLIES - PART 2: FITNESS FOR PURPOSE |
| BS EN 1993-6:2007 | Eurocode 3. Design of steel structures Crane supporting structures |
| BS EN 14399-6:2005 | High-strength structural bolting assemblies for preloading Plain chamfered washers |
| BS EN 14399-3:2015 | High-strength structural bolting assemblies for preloading System HR. Hexagon bolt and nut assemblies |
| BS EN 13107:2015 | Safety requirements for cableway installations designed to carry persons. Civil engineering works |
| BS EN 1994-2:2005 | Eurocode 4. Design of composite steel and concrete structures General rules and rules for bridges |
| BS EN 12812:2008 | Falsework. Performance requirements and general design |
| BS EN 15048-2:2007 | Non-preloaded structural bolting assemblies Suitability test |
| BS EN 13084-7:2012 | Free-standing chimneys Product specifications of cylindrical steel fabrications for use in single wall steel chimneys and steel liners |
| BS EN 1998-1 : 2004 | EUROCODE 8: DESIGN OF STRUCTURES FOR EARTHQUAKE RESISTANCE - PART 1: GENERAL RULES, SEISMIC ACTIONS AND RULES FOR BUILDINGS |
| 17/30326406 DC : 0 | BS EN 17168 - RAILWAY APPLICATIONS - PLATFORM BARRIER SYSTEMS |
| BS EN 1993-1-8:2005 | Eurocode 3. Design of steel structures Design of joints |
| UNE-EN 13084-7:2013 | Free-standing chimneys - Part 7: Product specifications of cylindrical steel fabrications for use in single wall steel chimneys and steel liners |
| BS EN 1994-1-1:2004 | Eurocode 4. Design of composite steel and concrete structures General rules and rules for buildings |
| BS EN 14399-4:2005 | High-strength structural bolting assemblies for preloading System HV. Hexagon bolt and nut assemblies |
| EN 74-2:2008 | Couplers, spigot pins and baseplates for use in falsework and scaffolds - Part 2: Special couplers - Requirements and test procedures |
| EN 14399-1:2015 | High-strength structural bolting assemblies for preloading - Part 1: General requirements |
| EN 14399-2:2015 | High-strength structural bolting assemblies for preloading - Part 2: Suitability for preloading |
| EN 14399-9:2018 | High-strength structural bolting assemblies for preloading - Part 9: System HR or HV - Direct tension indicators for bolt and nut assemblies |
| EN 16681:2016 | Steel static storage systems - Adjustable pallet racking systems - Principles for seismic design |
| EN 15048-2:2016 | Non-preloaded structural bolting assemblies - Part 2: Fitness for purpose |
| EN 16031:2012 | Adjustable telescopic aluminium props - Product specifications, design and assessment by calculation and tests |
| EN 14399-5:2015 | High-strength structural bolting assemblies for preloading - Part 5: Plain washers |
| EN 14399-4:2015 | High-strength structural bolting assemblies for preloading - Part 4: System HV - Hexagon bolt and nut assemblies |
| EN 14199:2015 | Execution of special geotechnical works - Micropiles |
| EN 14399-3:2015 | High-strength structural bolting assemblies for preloading - Part 3: System HR - Hexagon bolt and nut assemblies |
| EN 14399-6:2015 | High-strength structural bolting assemblies for preloading - Part 6: Plain chamfered washers |
| I.S. EN 15129:2009 | ANTI-SEISMIC DEVICES |
| I.S. EN 1993-1-3:2006 | EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 1-3: GENERAL RULES - SUPPLEMENTARY RULES FOR COLD-FORMED MEMBERS AND SHEETING (INCLUDING IRISH NATIONAL ANNEX) |
| 15/30332545 DC : 0 | BS EN 14399-7 - HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 7: SYSTEM HR - COUNTERSUNK HEAD BOLT AND NUT ASSEMBLIES |
| PREN 14399-4 : DRAFT 2013 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 4: SYSTEM HV - HEXAGON BOLT AND NUT ASSEMBLIES |
| UNE-EN 1993-1-4:2012 | Eurocode 3 - Design of steel structures - Part 1-4: General rules - Supplementary rules for stainless steels |
| I.S. EN 1993-4-2:2007 | EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 4-2: TANKS |
| 18/30366946 DC : 0 | BS EN 17206 - ENTERTAINMENT TECHNOLOGY - LIFTING AND LOAD-BEARING EQUIPMENT FOR STAGES AND OTHER PRODUCTION AREAS WITHIN THE ENTERTAINMENT INDUSTRY - SPECIFICATIONS FOR GENERAL REQUIREMENTS (EXCLUDING ALUMINUM AND STEEL TRUSSES AND TOWERS) |
| 13/30280740 DC : 0 | BS EN 12699 - EXECUTION OF SPECIAL GEOTECHNICAL WORK - DISPLACEMENT PILES |
| DIN EN 74-2:2009-01 | Couplers, spigot pins and baseplates for use in falsework and scaffolds - Part 2: Special couplers - Requirements and test procedures |
| NF EN 15129 : 2010 | ANTI-SEISMIC DEVICES |
| 15/30332554 DC : 0 | BS EN 14399-9 - HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 9: SYSTEM HR OR HV - DIRECT TENSION INDICATORS FOR BOLT AND NUT ASSEMBLIES |
| UNE-EN 1993-1-6:2013 | Eurocode 3 - Design of steel structures - Part 1-6: Strength and Stability of Shell Structures |
| UNE-EN 14399-3:2016 | High-strength structural bolting assemblies for preloading - Part 3: System HR - Hexagon bolt and nut assemblies |
| PREN 15129 : DRAFT 2017 | ANTI-SEISMIC DEVICES |
| PREN 14399-7 : DRAFT 2015 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 7: SYSTEM HR - COUNTERSUNK HEAD BOLT AND NUT ASSEMBLIES |
| UNE-EN 14399-2:2016 | High-strength structural bolting assemblies for preloading - Part 2: Suitability for preloading |
| KTA 3205.2 : 2015 COR 2016 | COMPONENT SUPPORT STRUCTURES WITH NON-INTEGRAL CONNECTIONS - PART 2: COMPONENT SUPPORT STRUCTURES WITH NON-INTEGRAL CONNECTIONS FOR PRESSURE AND ACTIVITY-RETAINING COMPONENTS IN SYSTEMS OUTSIDE THE PRIMARY CIRCUIT |
| I.S. EN 1090-1:2009 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 1: REQUIREMENTS FOR CONFORMITY ASSESSMENT OF STRUCTURAL COMPONENTS |
| UNE-EN 16031:2013 | Adjustable telescopic aluminium props - Product specifications, design and assessment by calculation and tests |
| S.R. CEN/TR 16949:2016 | ROAD RESTRAINT SYSTEM - PEDESTRIAN RESTRAINT SYSTEM - PEDESTRIAN PARAPETS |
| BS EN 1090-3:2008 | Execution of steel structures and aluminium structures Technical requirements for aluminium structures |
| 17/30354665 DC : 0 | BS EN 13031-1 - GREENHOUSES - DESIGN AND CONSTRUCTION - PART 1: COMMERCIAL PRODUCTION GREENHOUSES |
| BS EN 14399-9:2009 | High strength structural bolting for preloading System HR or HV. Direct tension indicators for bolt and nut assemblies |
| UNE-EN 1090-3:2011 | Execution of steel structures and aluminium structures - Part 3: Technical requirements for aluminium structures |
| I.S. EN 14399-9:2009 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 9: SYSTEM HR OR HV - DIRECT TENSION INDICATORS FOR BOLT AND NUT ASSEMBLIES |
| DIN EN 14399-5:2015-04 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 5: PLAIN WASHERS |
| DIN EN 14399-4:2015-04 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 4: SYSTEM HV - HEXAGON BOLT AND NUT ASSEMBLIES |
| DIN EN 14399-1:2015-04 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 1: GENERAL REQUIREMENTS |
| DIN EN 14399-6:2015-04 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 6: PLAIN CHAMFERED WASHERS |
| BS EN 14399-2 : 2015-02 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 2: SUITABILITY FOR PRELOADING |
| BS EN 14199:2015 | Execution of special geotechnical works. Micropiles |
| I.S. EN 1998-1:2005 | EUROCODE 8: DESIGN OF STRUCTURES FOR EARTHQUAKE RESISTANCE - PART 1: GENERAL RULES, SEISMIC ACTIONS AND RULES FOR BUILDINGS |
| EN 12699:2015 | Execution of special geotechnical works - Displacement piles |
| DIN EN 1090-1:2012-02 | Execution of steel structures and aluminium structures - Part 1: Requirements for conformity assessment of structural components (includes Amendment A1:2011) |
| EN ISO 1479:2011 | Hexagon head tapping screws (ISO 1479:2011) |
| ISO 10511:2012 | Prevailing torque type hexagon thin nuts (with non-metallic insert) |
| ISO 9018:2015 | Destructive tests on welds in metallic materials Tensile test on cruciform and lapped joints |
| ISO/TR 20172:2009 | Welding Grouping systems for materials European materials |
| EN ISO 15609-5:2011 | Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 5: Resistance welding (ISO 15609-5:2011, Corrected version 2011-12-01) |
| ISO 14555:2017 | Welding — Arc stud welding of metallic materials |
| EN ISO 16432:2007 | Resistance welding - Procedure for projection welding of uncoated and coated low carbon steels using embossed projection(s) (ISO 16432:2006) |
| EN ISO 9692-1:2013 | Welding and allied processes - Types of joint preparation - Part 1: Manual metal arc welding, gas-shielded metal arc welding, gas welding, TIG welding and beam welding of steels (ISO 9692-1:2013) |
| EN 14399-8:2007 | High-strength structural bolting assemblies for preloading - Part 8: System HV - Hexagon fit bolt and nut assemblies |
| EN 10162:2003 | Cold rolled steel sections - Technical delivery conditions - Dimensional and cross-sectional tolerances |
| ISO 14341:2010 | Welding consumables Wire electrodes and weld deposits for gas shielded metal arc welding of non alloy and fine grain steels Classification |
| ISO 2063:2005 | Thermal spraying Metallic and other inorganic coatings Zinc, aluminium and their alloys |
| ISO 898-2:2012 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 2: Nuts with specified property classes — Coarse thread and fine pitch thread |
| ISO 14373:2015 | Resistance welding — Procedure for spot welding of uncoated and coated low carbon steels |
| ISO/TR 3834-6:2007 | Quality requirements for fusion welding of metallic materials — Part 6: Guidelines on implementing ISO 3834 |
| ISO 7090:2000 | Plain washers, chamfered Normal series Product grade A |
| ISO 19840:2012 | Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Measurement of, and acceptance criteria for, the thickness of dry films on rough surfaces |
| EN ISO 5817:2014 | Welding - Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) - Quality levels for imperfections (ISO 5817:2014) |
| EN 1337-6:2004 | Structural bearings - Part 6: Rocker bearings |
| EN ISO 10511:2012 | Prevailing torque type hexagon thin nuts (with non-metallic insert) (ISO 10511:2012) |
| EN 10048:1996 | Hot rolled narrow steel strip - Tolerances on dimensions and shape |
| ISO 13918:2008 | Welding Studs and ceramic ferrules for arc stud welding |
| EN 10051:2010 | Continuously hot-rolled strip and plate/sheet cut from wide strip of non-alloy and alloy steels - Tolerances on dimensions and shape |
| EN ISO 15614-11:2002 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 11: Electron and laser beam welding (ISO 15614-11:2002) |
| ISO 15480:1999 | Hexagon washer head drilling screws with tapping screw thread |
| EN ISO 9445-2:2010 | Continuously cold-rolled stainless steel - Tolerances on dimensions and form - Part 2: Wide strip and plate/sheet (ISO 9445-2:2009) |
| EN ISO 7049:2011 | Cross-recessed pan head tapping screws (ISO 7049:2011) |
| EN 508-3:2008 | Roofing products from metal sheet - Specification for self-supporting products of steel, aluminium or stainless steel sheet - Part 3: Stainless steel |
| ISO 1479:2011 | Hexagon head tapping screws |
| EN ISO 7091:2000 | Plain washers - Normal series - Product grade C (ISO 7091:2000) |
| EN ISO 6789:2003 | Assembly tools for screws and nuts - Hand torque tools - Requirements and test methods for design conformance testing, quality conformance testing and recalibration procedure (ISO 6789:2003) |
| EN ISO 7040:2012 | Prevailing torque type hexagon regular nuts (with non-metallic insert) - Property classes 5, 8 and 10 (ISO 7040:2012) |
| ISO 14343:2017 | Welding consumables — Wire electrodes, strip electrodes, wires and rods for arc welding of stainless and heat resisting steels — Classification |
| ISO 15980:2002 | Open end blind rivets with break pull mandrel and countersunk head — St/St |
| EN 12385-1:2002+A1:2008 | Steel wire ropes - Safety - Part 1: General requirements |
| EN 10140:2006 | Cold rolled narrow steel strip - Tolerances on dimensions and shape |
| ISO 13920:1996 | Welding — General tolerances for welded constructions — Dimensions for lengths and angles — Shape and position |
| EN 10079:2007 | Definition of steel products |
| EN 14399-3:2015 | High-strength structural bolting assemblies for preloading - Part 3: System HR - Hexagon bolt and nut assemblies |
| EN 10025-4:2004 | Hot rolled products of structural steels - Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels |
| ISO 10684:2004 | Fasteners — Hot dip galvanized coatings |
| ISO 21670:2014 | Fasteners — Hexagon weld nuts with flange |
| EN ISO 7093-2:2000 | Plain washers - Large series - Part 2: Product grade C (ISO 7093-2:2000) |
| ISO 7042:2012 | Prevailing torque type all-metal hexagon high nuts — Property classes 5, 8, 10 and 12 |
| ISO 4042:1999 | Fasteners Electroplated coatings |
| ISO 3506-1:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners Part 1: Bolts, screws and studs |
| ISO 15614-13:2012 | Specification and qualification of welding procedures for metallic materials Welding procedure test Part 13: Upset (resistance butt) and flash welding |
| EN 10149-1:2013 | Hot rolled flat products made of high yield strength steels for cold forming - Part 1: General technical delivery conditions |
| EN 10027-2:2015 | Designation systems for steels - Part 2: Numerical system |
| ISO 17633:2010 | Welding consumables — Tubular cored electrodes and rods for gas shielded and non-gas shielded metal arc welding of stainless and heat-resisting steels — Classification |
| EN 15048-1:2016 | Non-preloaded structural bolting assemblies - Part 1: General requirements |
| EN ISO 4042:1999 | Fasteners - Electroplated coatings (ISO 4042:1999) |
| ISO 15614-11:2002 | Specification and qualification of welding procedures for metallic materials Welding procedure test Part 11: Electron and laser beam welding |
| EN ISO 7092:2000 | Plain washers - Small series - Product grade A (ISO 7092:2000) |
| EN ISO 15613:2004 | Specification and qualification of welding procedures for metallic materials - Qualification based on pre-production welding test (ISO 15613:2004) |
| EN 10029:2010 | Hot-rolled steel plates 3 mm thick or above - Tolerances on dimensions and shape |
| ISO 15620:2000 | Welding Friction welding of metallic materials |
| ISO 15983:2002 | Open end blind rivets with break pull mandrel and protruding head — A2/A2 |
| EN ISO 3506-1:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners - Part 1: Bolts, screws and studs (ISO 3506-1:2009) |
| ISO 10447:2015 | Resistance welding — Testing of welds — Peel and chisel testing of resistance spot and projection welds |
| EN ISO 15612:2004 | Specification and qualification of welding procedures for metallic materials - Qualification by adoption of a standard welding procedure (ISO 15612:2004) |
| EN 10268:2006+A1:2013 | Cold rolled steel flat products with high yield strength for cold forming - Technical delivery conditions |
| EN 10056-2:1993 | Structural steel equal and unequal leg angles - Part 2: Tolerances on shape and dimensions |
| ISO 14713-1:2017 | Zinc coatings — Guidelines and recommendations for the protection against corrosion of iron and steel in structures — Part 1: General principles of design and corrosion resistance |
| ISO 15610:2003 | Specification and qualification of welding procedures for metallic materials — Qualification based on tested welding consumables |
| ISO 8503-2:2012 | Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 2: Method for the grading of surface profile of abrasive blast-cleaned steel — Comparator procedure |
| EN 756:2004 | Welding consumables - Solid wires, solid wire-flux and tubular cored electrode-flux combinations for submerged arc welding of non alloy and fine grain steels - Classification |
| EN 10164:2004 | Steel products with improved deformation properties perpendicular to the surface of the product - Technical delivery conditions |
| EN 10244-2:2009 | Steel wire and wire products - Non-ferrous metallic coatings on steel wire - Part 2: Zinc or zinc alloy coatings |
| EN ISO 15620:2000 | Welding - Friction welding of metallic materials (ISO 15620:2000) |
| ISO 15979:2002 | Open end blind rivets with break pull mandrel and protruding head — St/St |
| EN ISO 7042:2012 | Prevailing torque type all-metal hexagon high nuts - Property classes 5, 8, 10 and 12 (ISO 7042:2012) |
| EN ISO 1461:2009 | Hot dip galvanized coatings on fabricated iron and steel articles - Specifications and test methods (ISO 1461:2009) |
| ISO 2808:2007 | Paints and varnishes Determination of film thickness |
| EN ISO 1481:2011 | Slotted pan head tapping screws (ISO 1481:2011) |
| ISO/TR 15608:2017 | Welding — Guidelines for a metallic materials grouping system |
| ISO 2320:2015 | Fasteners Prevailing torque steel nuts Functional properties |
| EN ISO 7090:2000 | Plain washers, chamfered - Normal series - Product grade A (ISO 7090:2000) |
| EN 10279:2000 | Hot rolled steel channels - Tolerances on shape, dimensions and mass |
| EN 10088-3:2014 | Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes |
| ISO 2560:2009 | Welding consumables Covered electrodes for manual metal arc welding of non-alloy and fine grain steels Classification |
| EN ISO 9445-1:2010 | Continuously cold-rolled stainless steel - Tolerances on dimensions and form - Part 1: Narrow strip and cut lengths (ISO 9445-1:2009) |
| EN ISO 15979:2002 | Open end blind rivets with break pull mandrel and protruding head - St/St (ISO 15979:2002) |
| ISO 15984:2002 | Open end blind rivets with break pull mandrel and countersunk head — A2/A2 |
| ISO 10509:2012 | Hexagon flange head tapping screws |
| EN 1011-1:2009 | Welding - Recommendations for welding of metallic materials - Part 1: General guidance for arc welding |
| EN 10149-2:2013 | Hot rolled flat products made of high yield strength steels for cold forming - Part 2: Technical delivery conditions for thermomechanically rolled steels |
| ISO 14731:2006 | Welding coordination Tasks and responsibilities |
| EN 10034:1993 | Structural steel I and H sections - Tolerances on shape and dimensions |
| EN ISO 7719:2012 | Prevailing torque type all-metal hexagon regular nuts - Property classes 5, 8 and 10 (ISO 7719:2012) |
| ISO 7049:2011 | Cross-recessed pan head tapping screws |
| ISO 18276:2017 | Welding consumables — Tubular cored electrodes for gas-shielded and non-gas-shielded metal arc welding of high strength steels — Classification |
| ISO 7976-2:1989 | Tolerances for building — Methods of measurement of buildings and building products — Part 2: Position of measuring points |
| EN 10264-4:2012 | Steel wire and wire products - Steel wire for ropes - Part 4: Stainless steel wire |
| EN ISO 4063:2010 | Welding and allied processes - Nomenclature of processes and reference numbers (ISO 4063:2009, Corrected version 2010-03-01) |
| EN 1337-2:2004 | Structural bearings - Part 2: Sliding elements |
| EN 10346:2015 | Continuously hot-dip coated steel flat products for cold forming - Technical delivery conditions |
| ISO/TR 17663:2001 | Welding Guidelines for quality requirements for heat treatment in connection with welding and allied processes |
| EN ISO 7093-1:2000 | Plain washers - Large series - Part 1: Product grade A (ISO 7093-1:2000) |
| ISO 1461:2009 | Hot dip galvanized coatings on fabricated iron and steel articles — Specifications and test methods |
| PREN 10138-3 : DRAFT 2000 | PRESTRESSING STEELS - PART 3: STRAND |
| EN ISO 16834:2012 | Welding consumables - Wire electrodes, wires, rods and deposits for gas shielded arc welding of high strength steels - Classification (ISO 16834:2012) |
| EN ISO 18276:2017 | Welding consumables - Tubular cored electrodes for gas-shielded and non-gas-shielded metal arc welding of high strength steels - Classification (ISO 18276:2017) |
| EN ISO 15976:2002 | Closed end blind rivets with break pull mandrel and protrudiing head - St/St (ISO 15976:2002) |
| EN 10139:2016 | Cold rolled uncoated low carbon steel narrow strip for cold forming - Technical delivery conditions |
| ISO 3443-2:1979 | Tolerances for building — Part 2: Statistical basis for predicting fit between components having a normal distribution of sizes |
| EN 10080:2005 | Steel for the reinforcement of concrete - Weldable reinforcing steel - General |
| EN 20898-2 : 1993 | MECHANICAL PROPERTIES OF FASTENERS - PART 2: NUTS WITH SPECIFIED PROOF LOAD VALUES - COARSE THREAD (ISO 898-2:1992) |
| EN 10025-1:2004 | Hot rolled products of structural steels - Part 1: General technical delivery conditions |
| ISO 9013:2017 | Thermal cutting — Classification of thermal cuts — Geometrical product specification and quality tolerances |
| EN 10088-2:2014 | Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes |
| EN ISO 9018:2015 | Destructive tests on welds in metallic materials - Tensile test on cruciform and lapped joints (ISO 9018:2015) |
| EN 10131:2006 | Cold rolled uncoated and zinc or zinc-nickel electrolytically coated low carbon and high yield strength steel flat products for cold forming - Tolerances on dimensions and shape |
| EN 473:2008 | Non-destructive testing - Qualification and certification of NDT personnel - General principles |
| ISO 10005:2005 | Quality management systems Guidelines for quality plans |
| EN 10024:1995 | Hot rolled taper flange I sections - Tolerances on shape and dimensions |
| EN 10210-1:2006 | Hot finished structural hollow sections of non-alloy and fine grain steels - Part 1: Technical delivery conditions |
| EN 1337-8:2007 | Structural bearings - Part 8: Guide Bearings and Restraint Bearings |
| EN 1090-1:2009+A1:2011 | Execution of steel structures and aluminium structures - Part 1: Requirements for conformity assessment of structural components |
| ISO 3834:1978 | Welding — Factors to be considered when assessing firms using welding as a prime means of fabrication |
| EN ISO 1127:1996 | Stainless steel tubes - Dimensions, tolerances and conventional masses per unit length (ISO 1127:1992) |
| ISO 15612:2004 | Specification and qualification of welding procedures for metallic materials Qualification by adoption of a standard welding procedure |
| ISO 5817:2014 | Welding — Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) — Quality levels for imperfections |
| EN ISO 15611:2003 | Specification and qualification of welding procedures for metallic materials - Qualification based on previous welding experience (ISO 15611:2003) |
| EN 10163-2:2004 | Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 2: Plate and wide flats |
| EN 1337-11:1997 | Structural bearings - Part 11: Transport, storage and installation |
| ISO 9692-1:2013 | Welding and allied processes — Types of joint preparation — Part 1: Manual metal arc welding, gas-shielded metal arc welding, gas welding, TIG welding and beam welding of steels |
| EN ISO 17652-2:2003 | Welding - Test for shop primers in relation to welding and allied processes - Part 2: Welding properties of shop primers (ISO 17652-2:2003) |
| ISO 15614-1:2017 | Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys |
| EN ISO 14373:2015 | Resistance welding - Procedure for spot welding of uncoated and coated low carbon steels (ISO 14373:2015) |
| EN 10060:2003 | Hot rolled round steel bars for general purposes - Dimensions and tolerances on shape and dimensions |
| ISO 15609-1:2004 | Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 1: Arc welding |
| EN 10169:2010+A1:2012 | Continuously organic coated (coil coated) steel flat products - Technical delivery conditions |
| EN ISO 13920:1996 | Welding - General tolerances for welded constructions - Dimensions for lengths and angles - Shape and position (ISO 13920:1996) |
| EN 13438:2013 | Paints and varnishes - Powder organic coatings for hot dip galvanised or sherardised steel products for construction purposes |
| ISO 15611:2003 | Specification and qualification of welding procedures for metallic materials — Qualification based on previous welding experience |
| EN 10219-1:2006 | Cold formed welded structural hollow sections of non-alloy and fine grain steels - Part 1: Technical delivery conditions |
| ISO 1481:2011 | Slotted pan head tapping screws |
| ISO 16834:2012 | Welding consumables — Wire electrodes, wires, rods and deposits for gas shielded arc welding of high strength steels — Classification |
| EN 10143:2006 | Continuously hot-dip coated steel sheet and strip - Tolerances on dimensions and shape |
| ISO 7089:2000 | Plain washers Normal series Product grade A |
| ISO 16432:2006 | Resistance welding Procedure for projection welding of uncoated and coated low carbon steels using embossed projection(s) |
| ISO 9445-2:2009 | Continuously cold-rolled stainless steel Tolerances on dimensions and form Part 2: Wide strip and plate/sheet |
| EN ISO 14341:2011 | Welding consumables - Wire electrodes and weld deposits for gas shielded metal arc welding of non alloy and fine grain steels - Classification (ISO 14341:2010) |
| EN 10264-3:2012 | Steel wire and wire products - Steel wire for ropes - Part 3: Round and shaped non alloyed steel wire for high duty applications |
| EN 10021:2006 | General technical delivery conditions for steel products |
| EN 13001-1:2015 | Cranes - General design - Part 1: General principles and requirements |
| ISO 4463-1:1989 | Measurement methods for building — Setting-out and measurement — Part 1: Planning and organization, measuring procedures, acceptance criteria |
| ISO 7719:2012 | Prevailing torque type all-metal hexagon regular nuts — Property classes 5, 8 and 10 |
| EN 1559-2:2014 | Founding - Technical conditions of delivery - Part 2: Additional requirements for steel castings |
| ISO 7091:2000 | Plain washers Normal series Product grade C |
| EN 10017:2004 | Steel rod for drawing and/or cold rolling - Dimensions and tolerances |
| CEN ISO/TR 3834-6:2007 | Quality requirements for fusion welding of metallic materials - Part 6: Guidelines on implementing ISO 3834 (ISO/TR 3834-6:2007) |
| EN ISO 2560:2009 | Welding consumables - Covered electrodes for manual metal arc welding of non-alloy and fine grain steels - Classification (ISO 2560:2009) |
| EN ISO 2320:2015 | Fasteners - Prevailing torque steel nuts - Functional properties (ISO 2320:2015) |
| EN ISO 21670:2014 | Fasteners - Hexagon weld nuts with flange (ISO 21670:2014) |
| ISO 7092:2000 | Plain washers Small series Product grade A |
| EN ISO 10513:2012 | Prevailing torque type all-metal hexagon high nuts with metric fine pitch thread - Property classes 8, 10 and 12 (ISO 10513:2012) |
| EN 1559-1:2011 | Founding - Technical conditions of delivery - Part 1: General |
| EN ISO 8503-1:2012 | Preparation of steel substrates before application of paints and related products - Surface roughness characteristics of blast-cleaned steel substrates - Part 1: Specifications and definitions for ISO surface profile comparators for the assessment of abrasive blast-cleaned surfaces (ISO 8503-1:2012) |
| ISO 10513:2012 | Prevailing torque type all-metal hexagon high nuts with metric fine pitch thread — Property classes 8, 10 and 12 |
| EN ISO 14713-1:2017 | Zinc coatings - Guidelines and recommendations for the protection against corrosion of iron and steel in structures - Part 1: General principles of design and corrosion resistance (ISO 14713-1:2017) |
| EN 14399-6:2015 | High-strength structural bolting assemblies for preloading - Part 6: Plain chamfered washers |
| EN ISO 8503-2:2012 | Preparation of steel substrates before application of paints and related products - Surface roughness characteristics of blast-cleaned steel substrates - Part 2: Method for the grading of surface profile of abrasive blast-cleaned steel - Comparator procedure (ISO 8503-2:2012) |
| ISO 10512:2012 | Prevailing torque type hexagon regular nuts (with non-metallic insert) with metric fine pitch thread — Property classes 6, 8 and 10 |
| ISO 17632:2015 | Welding consumables Tubular cored electrodes for gas shielded and non-gas shielded metal arc welding of non-alloy and fine grain steels Classification |
| ISO 7040:2012 | Prevailing torque type hexagon regular nuts (with non-metallic insert) — Property classes 5, 8 and 10 |
| EN 10025-5:2004 | Hot rolled products of structural steels - Part 5: Technical delivery conditions for structural steels with improved atmospheric corrosion resistance |
| EN 10163-3:2004 | Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 3: Sections |
| EN ISO 14343:2017 | Welding consumables - Wire electrodes, strip electrodes, wires and rods for arc welding of stainless and heat resisting steels - Classification (ISO 14343:2017) |
| EN 1337-3:2005 | Structural bearings - Part 3: Elastomeric bearings |
| EN 13411-4:2011 | Terminations for steel wire ropes - Safety - Part 4: Metal and resin socketing |
| EN 760:1996 | Welding consumables - Fluxes for submerged arc welding - Classification |
| EN ISO 14731:2006 | Welding coordination - Tasks and responsibilities (ISO 14731:2006) |
| EN 14399-1:2015 | High-strength structural bolting assemblies for preloading - Part 1: General requirements |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| EN 12062:1997/A2:2003 | NON-DESTRUCTIVE EXAMINATION OF WELDS - GENERAL RULES FOR METALLIC MATERIALS |
| EN 1993-3-2:2006 | Eurocode 3 - Design of steel structures - Part 3-2: Towers, masts and chimneys - Chimneys |
| EN ISO 17632:2015 | Welding consumables - Tubular cored electrodes for gas shielded and non-gas shielded metal arc welding of non-alloy and fine grain steels - Classification (ISO 17632:2015) |
| ISO 4997:2015 | Cold-reduced carbon steel sheet of structural quality |
| EN 1600:1997 | Welding consumables - Covered electrodes for manual arc welding of stainless and heat resisting steels - Classification |
| EN ISO 15609-1:2004 | Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 1: Arc welding (ISO 15609-1:2004) |
| EN 14399-4:2015 | High-strength structural bolting assemblies for preloading - Part 4: System HV - Hexagon bolt and nut assemblies |
| EN ISO 2063:2005 | Thermal spraying - Metallic and other inorganic coatings - Zinc, aluminium and their alloys (ISO 2063:2005) |
| ISO 286-2:2010 | Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts |
| EN ISO 16433:2007 | Resistance welding - Procedure for seam welding of uncoated and coated low carbon steels (ISO 16433:2006) |
| EN ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread (ISO 898-1:2013) |
| EN 10027-1:2016 | Designation systems for steels - Part 1: Steel names |
| ISO 14554-1:2013 | Quality requirements for welding — Resistance welding of metallic materials — Part 1: Comprehensive quality requirements |
| ISO 17652-2:2003 | Welding — Test for shop primers in relation to welding and allied processes — Part 2: Welding properties of shop primers |
| EN 10025-6:2004+A1:2009 | Hot rolled products of structural steels - Part 6: Technical delivery conditions for flat products of high yield strength structural steels in the quenched and tempered condition |
| ISO 9000:2015 | Quality management systems — Fundamentals and vocabulary |
| EN 1713:1998/A2:2003 | NON-DESTRUCTIVE TESTING OF WELDS - ULTRASONIC TESTING - CHARACTERIZATION OF INDICATIONS IN WELDS |
| ISO 14175:2008 | Welding consumables — Gases and gas mixtures for fusion welding and allied processes |
| ISO 7976-1:1989 | Tolerances for building — Methods of measurement of buildings and building products — Part 1: Methods and instruments |
| ISO 15609-5:2011 | Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 5: Resistance welding |
| ISO 8503-1:2012 | Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 1: Specifications and definitions for ISO surface profile comparators for the assessment of abrasive blast-cleaned surfaces |
| EN ISO 15614-13:2012 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 13: Upset (resistance butt) and flash welding (ISO 15614-13:2012) |
| EN 10020:2000 | Definition and classification of grades of steel |
| ISO 6789:2003 | Assembly tools for screws and nuts Hand torque tools Requirements and test methods for design conformance testing, quality conformance testing and recalibration procedure |
| ISO 15976:2002 | Closed end blind rivets with break pull mandrel and protruding head — St/St |
| EN 10219-2:2006 | Cold formed welded structural hollow sections of non-alloy and fine grain steels - Part 2: Tolerances, dimensions and sectional properties |
| ISO 3443-1:1979 | Tolerances for building — Part 1: Basic principles for evaluation and specification |
| EN 12385-10:2003+A1:2008 | Steel wire ropes - Safety - Part 10: Spiral ropes for general structural applications |
| EN 14399-7:2007 | High-strength structural bolting assemblies for preloading - Part 7: System HR - Countersunk head bolt and nut assemblies |
| EN 10061:2003 | Hot rolled hexagon steel bars for general purposes - Dimensions and tolerances on shape and dimensions |
| EN 10059:2003 | Hot rolled square steel bars for general purposes - Dimensions and tolerances on shape and dimensions |
| EN 1337-7:2004 | Structural bearings - Part 7: Spherical and cylindrical PTFE bearings |
| CEN/TR 10347:2006 | Guidance for forming of structural steels in processing |
| ISO 16433:2006 | Resistance welding Procedure for seam welding of uncoated and coated low carbon steels |
| ISO 9692-2:1998 | Welding and allied processes — Joint preparation — Part 2: Submerged arc welding of steels |
| EN ISO 15609-4:2009 | Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 4: Laser beam welding (ISO 15609-4:2009) |
| EN ISO 15980:2002 | Open end blind rivets with break pull mandrel and countersunk head - St/St (ISO 15980:2002) |
| ISO 7093-2:2000 | Plain washers Large series Part 2: Product grade C |
| EN 14399-5:2015 | High-strength structural bolting assemblies for preloading - Part 5: Plain washers |
| EN 14295 : 2003 | WELDING CONSUMABLES - WIRE AND TUBULAR CORED ELECTRODES AND ELECTRODE-FLUX COMBINATIONS FOR SUBMERGED ARC WELDING OF HIGH STRENGTH STEELS - CLASSIFICATION |
| ISO 15613:2004 | Specification and qualification of welding procedures for metallic materials Qualification based on pre-production welding test |
| ISO 4063:2009 | Welding and allied processes — Nomenclature of processes and reference numbers |
| EN ISO 15480:1999 | Hexagon washer head drilling screws with tapping screw thread (ISO 15480:1999) |
| EN ISO 636:2017 | Welding consumables - Rods, wires and deposits for tungsten inert gas welding of non-alloy and fine-grain steels - Classification (ISO 636:2017) |
| ISO 14713-2:2009 | Zinc coatings Guidelines and recommendations for the protection against corrosion of iron and steel in structures Part 2: Hot dip galvanizing |
| EN 10055:1995 | Hot rolled steel equal flange tees with radiused root and toes - Dimensions and tolerances on shape and dimensions |
| EN ISO 14555:2017 | Welding - Arc stud welding of metallic materials (ISO 14555:2017) |
| EN ISO 15610:2003 | Specification and qualification of welding procedures for metallic materials - Qualification based on tested welding consumables (ISO 15610:2003) |
| ISO 3443-3:1987 | Tolerances for building — Part 3: Procedures for selecting target size and predicting fit |
| EN ISO 9013:2017 | Thermal cutting - Classification of thermal cuts - Geometrical product specification and quality tolerances (ISO 9013:2017) |
| EN 571-1:1997 | Non destructive testing - Penetrant testing - Part 1: General principles |
| ISO 9445-1:2009 | Continuously cold-rolled stainless steel Tolerances on dimensions and form Part 1: Narrow strip and cut lengths |
| EN 1418:1997 | Welding personnel - Approval testing of welding operators for fusion welding and resistance weld setters for fully mechanized and automatic welding of metallic materials |
| EN ISO 7089:2000 | Plain washers - Normal series - Product grade A (ISO 7089:2000) |
| EN 10160:1999 | Ultrasonic testing of steel flat product of thickness equal or greater than 6 mm (reflection method) |
| ISO 3506-2:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners Part 2: Nuts |
| ISO 13916:2017 | Welding — Measurement of preheating temperature, interpass temperature and preheat maintenance temperature |
| EN 970:1997 | Non-destructive examination of fusion welds - Visual examination |
| ISO 1803:1997 | Building construction Tolerances Expression of dimensional accuracy Principles and terminology |
| EN ISO 15984:2002 | Open end blind rivets with break pull mandrel and countersunk head - A2/A2 (ISO 15984:2002) |
| EN 1290:1998/A2:2003 | NON-DESTRUCTIVE EXAMINATION OF WELDS - MAGNETIC PARTICLE EXAMINATION OF WELDS |
| EN 10025-3:2004 | Hot rolled products of structural steels - Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels |
| EN 1337-5:2005 | Structural bearings - Part 5: Pot bearings |
| ISO 2859-5:2005 | Sampling procedures for inspection by attributes — Part 5: System of sequential sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection |
| EN ISO 15983:2002 | Open end blind rivets with break pull mandrel and protruding head - A2/A2 (ISO 15983:2002) |
| ISO 15609-4:2009 | Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 4: Laser beam welding |
| ISO 636:2017 | Welding consumables — Rods, wires and deposits for tungsten inert gas welding of non-alloy and fine-grain steels — Classification |
| EN 13670:2009 | Execution of concrete structures |
| EN 15311:2007 | Thermal spraying - Components with thermally sprayed coatings - Technical supply conditions |
| EN ISO 10512:2012 | Prevailing torque type hexagon regular nuts (with non-metallic insert) with metric fine pitch thread - Property classes 6, 8 and 10 (ISO 10512:2012) |
| EN 14616:2004 | Thermal spraying - Recommendations for thermal spraying |
| EN 10149-3:2013 | Hot rolled flat products made of high yield strength steels for cold forming - Part 3: Technical delivery conditions for normalized or normalized rolled steels |
| EN ISO 9000:2015 | Quality management systems - Fundamentals and vocabulary (ISO 9000:2015) |
| EN 757:1997 | Welding consumables - Covered electrodes for manual metal arc welding of high strength steels - Classification |
| EN ISO 10447:2015 | Resistance welding - Testing of welds - Peel and chisel testing of resistance spot and projection welds (ISO 10447:2015) |
| EN 13479:2017 | Welding consumables - General product standard for filler metals and fluxes for fusion welding of metallic materials |
| EN ISO 2808:2007 | Paints and varnishes - Determination of film thickness (ISO 2808:2007) |
| EN 508-1:2014 | Roofing and cladding products from metal sheet - Specification for self-supporting of steel, aluminium or stainless steel sheet - Part 1: Steel |
| EN 14399-2:2015 | High-strength structural bolting assemblies for preloading - Part 2: Suitability for preloading |
| ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread |
| EN 10088-1:2014 | Stainless steels - Part 1: List of stainless steels |
| ISO 1127:1992 | Stainless steel tubes Dimensions, tolerances and conventional masses per unit length |
| ISO 7093-1:2000 | Plain washers Large series Part 1: Product grade A |
| EN ISO 14713-2:2009 | Zinc coatings - Guidelines and recommendations for the protection against corrosion of iron and steel in structures - Part 2: Hot dip galvanizing (ISO 14713-2:2009) |
| EN ISO 3506-2:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners - Part 2: Nuts (ISO 3506-2:2009) |
| EN 287-1:2011 | Qualification test of welders - Fusion welding - Part 1: Steels |
| EN ISO 14175:2008 | Welding consumables - Gases and gas mixtures for fusion welding and allied processes (ISO 14175:2008) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.