ASTM E 691 : 2020
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
Hardcopy , PDF
06-01-2022
English
08-03-2021
Committee |
E 11
|
DocumentType |
Standard Practice
|
Pages |
30
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This practice describes the techniques for planning, conducting, analyzing, and treating the results of an interlaboratory study (ILS) of a test method. The statistical techniques described in this practice provide adequate information for formulating the precision statement of a test method.
1.2This practice does not concern itself with the development of test methods but rather with gathering the information needed for a test method precision statement after the development stage has been successfully completed. The data obtained in the interlaboratory study may indicate, however, that further effort is needed to improve the test method.
1.3Since the primary purpose of this practice is the development of the information needed for a precision statement, the experimental design in this practice may not be optimum for evaluating materials, apparatus, or individual laboratories.
1.4Field of Application—This practice is concerned exclusively with test methods which yield a single numerical figure as the test result, although the single figure may be the outcome of a calculation from a set of measurements.
1.4.1This practice does not cover methods in which the measurement is a categorization; however, for many practical purposes categorical outcomes can be scored, such as zero-one scoring for binary measurements or as integers, ranks for example, for well-ordered categories and then the test result can be defined as an average, or other summary statistic, of several individual scores.
1.5This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 7819 : 2012 : R2021 | Standard Test Method for Enumeration of Yeast and Mold on Fresh (Uncured) Hides and Skins |
ASTM D 1693 : 2021 | Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics |
ASTM D 5403 : 1993 : R2021 | Standard Test Methods for Volatile Content of Radiation Curable Materials |
ASTM E 247 : 2021 | Standard Test Method for Determination of Silica in Manganese Ores, Iron Ores, and Related Materials by Gravimetry |
ASTM F 1951 : 2021 | Standard Specification for Determination of Accessibility of Surface Systems Under and Around Playground Equipment |
ASTM D 7817 : 2012 : R2021 | Standard Test Method for Enumeration of Yeast and Mold in Raceway Brine, Brine-Cured Hides and Skins |
ASTM D 3389 : 2021 | Standard Test Method for Coated Fabrics Abrasion Resistance (Rotary Platform Abrader) |
ASTM E 3269 : 2021 | Standard Test Method for Determination of the Mass Fraction of Particle-Bound Gold in Colloidal Gold Suspensions |
ASTM E 1414/E1414M : 2021 : REV A | Standard Test Method for Airborne Sound Attenuation Between Rooms Sharing a Common Ceiling Plenum |
ASTM E 415 : 2021 | Standard Test Method for Analysis of Carbon and Low-Alloy Steel by Spark Atomic Emission Spectrometry |
ASTM E 246 : 2021 | Standard Test Methods for Determination of Iron in Iron Ores and Related Materials by Dichromate Titrimetry |
ASTM G 152 : 2013 : R2021 | Standard Practice for Operating Open Flame Carbon Arc Light Apparatus for Exposure of Nonmetallic Materials |
ASTM E 855 : 2021 | Standard Test Methods for Bend Testing of Metallic Flat Materials for Spring Applications Involving Static Loading |
ASTM D 7748/D7748M : 2014 : R2021 | Standard Test Method for Flexural Rigidity of Geogrids, Geotextiles, and Related Products |
ASTM C 1733 : 2021 | Standard Test Method for Distribution Coefficients of Inorganic Species by Batch Method |
ASTM E 991 : 2021 | Standard Practice for Color Measurement of Fluorescent Specimens Using the One-Monochromator Method |
ASTM D 3032 : 2021 : REV A | Standard Test Methods for Hookup Wire Insulation |
ASTM D 7637 : 2010 : R2021 | Standard Test Method for Determination of Glycerin Assay by Titration (Sodium Meta Periodate) |
ASTM F 801 : 2021 | Standard Test Method for Measuring Optical Angular Deviation of Transparent Parts |
ASTM D 952 : 2015 : R2021 | Standard Test Method for Bond or Cohesive Strength of Sheet Plastics and Electrical Insulating Materials |
ASTM C 67/C67M : 2021 | Standard Test Methods for Sampling and Testing Brick and Structural Clay Tile |
ASTM C 518 : 2021 | Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus |
ASTM F 36 : 2015 : R2021 | Standard Test Method for Compressibility and Recovery of Gasket Materials |
ASTM D 4751 : 2021 : REV A | Standard Test Methods for Determining Apparent Opening Size of a Geotextile |
ASTM D 7984 : 2021 | Standard Test Method for Measurement of Thermal Effusivity of Fabrics Using a Modified Transient Plane Source (MTPS) Instrument |
ASTM C 1819 : 2021 | Standard Test Method for Hoop Tensile Strength of Continuous Fiber-Reinforced Advanced Ceramic Composite Tubular Test Specimens at Ambient Temperature Using Elastomeric Inserts |
ASTM F2824:2010(R2020) | Standard Test Method for Mechanical Seal Strength Testing for Round Cups and Bowl Containers with Flexible Peelable Lids<br> |
ASTM D 7584 : 2016 : R2021 | Standard Test Method for Evaluating the Resistance of the Surface of Wet Blue and Wet White to the Growth of Fungi in an Environmental Chamber |
ASTM D 1998 : 2021 | Standard Specification for Polyethylene Upright Storage Tanks |
ASTM D 7370/D7370M : 2014 : R2021 | Standard Test Method for Determination of Relative Density and Absorption of Fine, Coarse, and Blended Aggregate Using Combined Vacuum Saturation and Rapid Submersion |
ASTM D 3963/D3963M : 2021 | Standard Specification for Fabrication and Jobsite Handling of Epoxy-Coated Steel Reinforcing Bars |
ASTM D 4085 : 1993 : R2021 | Standard Test Method for Metals in Cellulose by Atomic Absorption Spectrophotometry |
ASTM B 212 : 2021 | Standard Test Method for Apparent Density of Free-Flowing Metal Powders Using the Hall Flowmeter Funnel |
ASTM D 7133 : 2021 | Standard Test Method for Polyurethane Raw Materials: Instrumental Measurement of Tristimulus CIELAB Color and Yellowness Index of Liquids |
ASTM E 3246 : 2021 | Standard Test Methods for Differential Indentation Depth Hardness of Metallic Materials |
ASTM E 456 : 2013 : REV A : R2017 : EDT 5 | Standard Terminology Relating to Quality and Statistics |
ASTM B 636/B636M : 2015 : R2021 | Standard Test Method for Measurement of Internal Stress of Plated Metallic Coatings with the Spiral Contractometer |
ASTM D 4481 : 2021 | Standard Test Method for Total Nickel in Fresh Alumina-Base Catalysts |
ASTM B 934 : 2021 | Standard Test Method for Effective Case Depth of Ferrous Powder Metallurgy (PM) Parts Using Microindentation Hardness Measurements |
ASTM E 2242 : 2021 | Standard Test Method for Column Percolation Extraction of Mine Rock by the Meteoric Water Mobility Procedure |
ASTM E 1918 : 2021 | Standard Test Method for Measuring Solar Reflectance of Horizontal and Low-Sloped Surfaces in the Field |
ASTM E 2371 : 2021 | Standard Test Method for Analysis of Titanium and Titanium Alloys by Direct Current Plasma and Inductively Coupled Plasma Atomic Emission Spectrometry (Performance-Based Test Methodology) |
ASTM E 2536 : 2021 | Standard Guide for Assessment of Measurement Uncertainty in Fire Tests |
ASTM D 1353 : 2013 : R2021 | Standard Test Method for Nonvolatile Matter in Volatile Solvents for Use in Paint, Varnish, Lacquer, and Related Products |
ASTM D 2457 : 2021 | Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics |
ASTM G 204 : 2021 | Standard Test Method for Damage to Contacting Solid Surfaces under Fretting Conditions |
ASTM D 955 : 2021 | Standard Test Method of Measuring Shrinkage from Mold Dimensions of Thermoplastics |
ASTM D 4326 : 2021 | Standard Test Method for Major and Minor Elements in Coal Ash By X-Ray Fluorescence |
ASTM G 180 : 2021 | Standard Test Method for Corrosion Inhibiting Admixtures for Steel in Concrete by Polarization Resistance in Cementitious Slurries |
ASTM B 873 : 2021 | Standard Test Method for Measuring Volume of Apparent Density Cup Used in Test Methods B212, B329, and B417 |
ASTM D 2116 : 2016 : R2021 | Standard Specification for FEP Resin Molding and Extrusion Materials |
ASTM E 2945 : 2014 : R2021 | Standard Test Method for Film Permeability Determination Using Static Permeability Cells |
ASTM D 7889 : 2021 | Standard Test Method for Field Determination of In-Service Fluid Properties Using IR Spectroscopy |
ASTM E 3193 : 2021 | Standard Test Method for Measurement of Lead (Pb) in Dust by Wipe, Paint, and Soil by Flame Atomic Absorption Spectrophotometry (FAAS) |
ASTM D 7843 : 2021 | Standard Test Method for Measurement of Lubricant Generated Insoluble Color Bodies in In-Service Turbine Oils using Membrane Patch Colorimetry |
ASTM E 1875 : 2020 : REV A | Standard Test Method for Dynamic Young's Modulus, Shear Modulus, and Poisson's Ratio by Sonic Resonance |
ASTM E 3171 : 2021 : REV A | Standard Test Method for Determination of Total Silver in Textiles by ICP-OES or ICP-MS Analysis |
ASTM C 1285 : 2021 | Standard Test Methods for Determining Chemical Durability of Nuclear, Hazardous, and Mixed Waste Glasses and Multiphase Glass Ceramics: The Product Consistency Test (PCT) |
ASTM F 1515 : 2021 | Standard Test Method for Measuring Light Stability of Resilient Flooring by Color Change |
ASTM E 278 : 2021 | Standard Test Method for Determination of Phosphorus in Iron Ores by Phosphomolybdate Coprecipitation and Nitric Acid Titrimetry |
ASTM E 606/E606M : 2021 | Standard Test Method for Strain-Controlled Fatigue Testing |
ASTM D 4329 : 2021 | Standard Practice for Fluorescent Ultraviolet (UV) Lamp Apparatus Exposure of Plastics |
ASTM D 6476 : 2012 : R2021 | Standard Test Method for Determining Dynamic Air Permeability of Inflatable Restraint Fabrics |
ASTM G 5 : 2014 : R2021 | Standard Reference Test Method for Making Potentiodynamic Anodic Polarization Measurements |
ASTM D 6657 : 2016 : R2021 | Standard Test Method for pH of Wet Blue and Wet White |
ASTM F 1863 : 2016 : R2021 | Standard Test Method for Measuring the Night Vision Goggle-Weighted Transmissivity of Transparent Parts |
ASTM E 1582 : 2021 | Standard Test Method for Temperature Calibration of Thermogravimetric Analyzers |
ASTM D 7439 : 2021 | Standard Test Method for Determination of Elements in Airborne Particulate Matter by Inductively Coupled Plasma–Mass Spectrometry |
ASTM G 141 : 2009 : R2021 | Standard Guide for Addressing Variability in Exposure Testing of Nonmetallic Materials |
ASTM D 7698 : 2021 | Standard Test Method for In-Place Estimation of Density and Water Content of Soil and Aggregate by Correlation with Complex Impedance Method |
ASTM D 7309 : 2021 : REV B | Standard Test Method for Determining Flammability Characteristics of Plastics and Other Solid Materials Using Microscale Combustion Calorimetry |
ASTM D 7553 : 2015 : R2021 | Standard Test Method for Solubility of Asphalt Materials in N-Propyl Bromide |
ASTM D 7348 : 2021 | Standard Test Methods for Loss on Ignition (LOI) of Solid Combustion Residues |
ASTM D 1003 : 2021 | Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics |
ASTM D 8393 : 2021 | Standard Guide for Determination of Pore Volume of Powdered Catalysts and Catalyst Carriers by Water Adsorption |
ASTM D 7310 : 2021 | Standard Practice for Defect Detection and Rating of Plastic Films Using Optical Sensors |
ASTM D 4274 : 2021 | Standard Test Methods for Testing Polyurethane Raw Materials: Determination of Hydroxyl Numbers of Polyols |
ASTM D 8342/D8342M : 2021 | Standard Test Method for Measuring the Probability of a Full Length Burn on a Cannabis/Hemp Pre-roll |
ASTM D 5419 : 2021 | Standard Test Method for Environmental Stress Crack Resistance (ESCR) of Threaded Plastic Closures |
ASTM C 1735 : 2017 : R2021 | Standard Test Method for Measuring the Time Dependent Modulus of Sealants Using Stress Relaxation |
ASTM B 761 : 2017 : R2021 | Standard Test Method for Particle Size Distribution of Metal Powders and Related Compounds by X-Ray Monitoring of Gravity Sedimentation |
ASTM D 5758 : 2001 : R2021 | Standard Test Method for Determination of Relative Crystallinity of Zeolite ZSM-5 by X-Ray Diffraction |
ASTM E 2269 : 2021 | Standard Test Method for Determining Argon Concentration in Sealed Insulating Glass Units using Gas Chromatography |
ASTM D 1499 : 2013 : R2021 | Standard Practice for Filtered Open-Flame Carbon-Arc Exposures of Plastics |
ASTM D 4475 : 2021 | Standard Test Method for Apparent Horizontal Shear Strength of Pultruded Reinforced Plastic Rods By the Short-Beam Method |
ASTM D 698 : 2012 : R2021 | Standard Test Methods for Laboratory Compaction Characteristics of Soil Using Standard Effort (12,400 ft-lbf/ft<sup>3</sup> (600 kN-m/m<sup>3</sup>)) |
ASTM D 8394 : 2021 | Standard Test Method for Automated Measurement of Maturity, Fineness, Ribbon Width, and Micronaire of Cotton Fibers |
ASTM B 939 : 2021 | Standard Test Method for Radial Crushing Strength, <emph type="bdit">K</emph>, of Powder Metallurgy (PM) Bearings and Structural Materials |
ASTM C 739 : 2021 : REV A | Standard Specification for Cellulosic Fiber Loose-Fill Thermal Insulation |
ASTM C 471M : 2020 : REV A : EDT 1 | Standard Test Methods for Chemical Analysis of Gypsum and Gypsum Products (Metric) |
ASTM B 703 : 2021 | Standard Test Method for Apparent Density of Metal Powders and Related Compounds Using the Arnold Meter |
ASTM D 6037 : 2021 | Standard Test Methods for Dry Abrasion Mar Resistance of High Gloss Coatings |
ASTM D 7504 : 2021 | Standard Test Method for Trace Impurities in Monocyclic Aromatic Hydrocarbons by Gas Chromatography and Effective Carbon Number |
ASTM D 6299 : 2021 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
ASTM D 7427 : 2016 : R2021 | Standard Test Method for Immunological Measurement of Four Principal Allergenic Proteins (Hev b 1, 3, 5 and 6.02) in Hevea Natural Rubber and Its Products Derived from Latex (Withdrawn 2023) |
ASTM D 7707 : 2021 | Standard Specification for Wipe Sampling Materials for Beryllium in Surface Dust |
ASTM C 1259 : 2021 | Standard Test Method for Dynamic Young’s Modulus, Shear Modulus, and Poisson’s Ratio for Advanced Ceramics by Impulse Excitation of Vibration |
ASTM D 3420 : 2021 | Standard Test Method for Pendulum Impact Resistance of Plastic Film |
ASTM C 832 : 2021 | Standard Test Method for Measuring Thermal Expansion and Creep of Refractories Under Load |
ASTM D 7542 : 2021 | Standard Test Method for Air Oxidation of Carbon and Graphite in the Kinetic Regime |
ASTM D 1203 : 2021 | Standard Test Methods for Volatile Loss from Plastics Using Activated Carbon Methods |
ASTM D 2582 : 2021 | Standard Test Method for Puncture-Propagation Tear Resistance of Plastic Film and Thin Sheeting |
ASTM D 3418 : 2021 | Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry |
ASTM E 248 : 2020 | Standard Test Method for Determination of Manganese in Manganese Ores by Pyrophosphate Complexed Permanganate Potentiometric Titrimetry |
ASTM A 428/A428M : 2021 | Standard Test Method for Weight [Mass] of Coating on Aluminum-Coated Iron or Steel Articles |
ASTM D 7674 : 2014 : REV A : R2021 | Standard Test Method for Hexane/Petroleum Ether Extract in Wet Blue and Wet White |
ASTM F 2095 : 2007 : R2021 | Standard Test Methods for Pressure Decay Leak Test for Flexible Packages With and Without Restraining Plates |
ASTM C 1773 : 2021 | Standard Test Method for Monotonic Axial Tensile Behavior of Continuous Fiber-Reinforced Advanced Ceramic Tubular Test Specimens at Ambient Temperature |
ASTM D 8115 : 2017 : R2021 | Standard Test Method for Rubber Property—Abrasion Resistance (Multi-Directional Platform Abrader) |
ASTM E 1921 : 2021 | Standard Test Method for Determination of Reference Temperature, <emph type="bdit">T<inf >o</inf></emph>, for Ferritic Steels in the Transition Range |
ASTM C 1427 : 2021 | Standard Specification for Extruded Preformed Flexible Cellular Polyolefin Thermal Insulation in Sheet and Tubular Form |
ASTM D 6300 : 2021 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 6113 : 2021 | Standard Test Method for Using Cone Calorimeter to Determine Fire-Test-Response Characteristics of Insulating Materials Contained in Electrical or Optical Fiber Cables |
ASTM D 198 : 2021 : REV A | Standard Test Methods of Static Tests of Lumber in Structural Sizes |
ASTM E 1353 : 2021 | Standard Test Methods for Cigarette Ignition Resistance of Components of Upholstered Furniture (Withdrawn 2022) |
ASTM E 1805 : 2021 | Standard Test Method for Determination of Gold in Copper Concentrates by Fire Assay Gravimetry |
ASTM E 572 : 2021 | Standard Test Method for Analysis of Stainless and Alloy Steels by Wavelength Dispersive X-Ray Fluorescence Spectrometry |
ASTM D 4491/D4491M : 2021 | Standard Test Methods for Water Permeability of Geotextiles by Permittivity |
ASTM D 7816 : 2012 : R2021 | Standard Test Method for Enumeration of Halophilic and Proteolytic Bacteria in Raceway Brine, Brine-Cured Hides and Skins |
ASTM D 5994/D5994M : 2010 : R2021 | Standard Test Method for Measuring Core Thickness of Textured Geomembranes |
ASTM C 1511 : 2015 : R2021 | Standard Test Method for Determining the Water Retention (Repellency) Characteristics of Fibrous Glass Insulation (Aircraft Type) |
ASTM C 695 : 2021 | Standard Test Method for Compressive Strength of Carbon and Graphite |
ASTM F 2894 : 2021 | Standard Test Method for Evaluation of Materials, Protective Clothing, and Equipment for Heat Resistance Using a Hot Air Circulating Oven |
ASTM D 5178 : 2021 | Standard Test Method for Mar Resistance of Organic Coatings |
ASTM D 7570 : 2017 : R2021 : EDT 1 | Standard Test Method for Evaluation of Dimensional Stability of Pile Yarn Floor Covering |
ASTM F 2055 : 2017 : R2021 | Standard Test Method for Size and Squareness of Resilient Floor Tile by Dial Gauge Method |
ASTM E 1868 : 2010 : R2021 | Standard Test Methods for Loss-On-Drying by Thermogravimetry |
ASTM D 6817/D6817M : 2017 : R2021 | Standard Specification for Rigid Cellular Polystyrene Geofoam |
ASTM D 8117 : 2021 | Standard Test Method for Oxidative Induction Time of Polyolefin Geosynthetics by Differential Scanning Calorimetry |
ASTM D 6349 : 2021 | Standard Test Method for Determination of Major and Minor Elements in Coal, Coke, and Solid Residues from Combustion of Coal and Coke by Inductively Coupled Plasma—Atomic Emission Spectrometry |
ASTM F 1717 : 2021 | Standard Test Methods for Spinal Implant Constructs in a Vertebrectomy Model |
ASTM D 8108 : 2021 | Standard Test Method for Determination of Particulate Matter Mass from Light Duty Mobile Sources (Gravimetric Method) |
ASTM G 153 : 2013 : R2021 | Standard Practice for Operating Enclosed Carbon Arc Light Apparatus for Exposure of Nonmetallic Materials |
ASTM B 982 : 2020 | Standard Specification for Sampling and Sample Preparation of Lead and Lead Alloys for Optical Emission Spectrometric or ICP Analysis |
ASTM F 3080 : 2021 | Standard Practice for Laser Technologies for Measurement of Cross-Sectional Shape of Pipeline and Conduit by Non-Rotating Laser Projector, Infrared Measurement, and CCTV Camera System |
ASTM E 2008 : 2017 : R2021 | Standard Test Methods for Volatility Rate by Thermogravimetry |
ASTM G 32 : 2016 : R2021 : EDT 1 | Standard Test Method for Cavitation Erosion Using Vibratory Apparatus |
ASTM D 7477 : 2016 : R2021 | Standard Test Method for Determining the Area Stability of Wet Blue Submersed in Boiling Water |
ASTM D 6641/D6641M : 2016 : EDT 2 | Standard Test Method for Compressive Properties of Polymer Matrix Composite Materials Using a Combined Loading Compression (CLC) Test Fixture |
ASTM D 6656 : 2016 : R2021 | Standard Test Method for Determination of Chromic Oxide in Wet Blue (Perchloric Acid Oxidation) |
ASTM G 211 : 2014 : R2020 | Standard Test Method for Conducting Elevated Temperature Erosion Tests by Solid Particle Impingement Using Gas Jets |
ASTM F 1926/F1926M : 2014 : R2021 | Standard Test Method for Dissolution Testing of Calcium Phosphate Granules, Fabricated Forms, and Coatings |
ASTM C 1559 : 2015 : R2021 | Standard Test Method for Determining Wicking of Fibrous Glass Blanket Insulation (Aircraft Type) |
ASTM D 7830/D7830M : 2014 : R2021 : EDT 1 | Standard Test Method for In-Place Density (Unit Weight) and Water Content of Soil Using an Electromagnetic Soil Density Gauge |
ASTM B 578 : 2021 | Standard Test Method for Microindentation Hardness of Electroplated Coatings |
ASTM D 6360 : 2015 : R2021 | Standard Practice for Enclosed Carbon-Arc Exposures of Plastics |
ASTM D 7818 : 2012 : R2021 | Standard Test Method for Enumeration of Proteolytic Bacteria in Fresh (Uncured) Hides and Skins |
ASTM D 7967 : 2021 | Standard Test Method for Analysis of Chrome Content (as Cr<inf>2</inf>O<inf>3</inf>) in Wet Blue using Atomic Absorption or ICP |
ASTM D 5227 : 2021 | Standard Test Method for Measurement of Hexane Extractable Content of Polyolefins |
ASTM D 7234 : 2021 | Standard Test Method for Pull-Off Adhesion Strength of Coatings on Concrete Using Portable Pull-Off Adhesion Testers |
ASTM D 8405 : 2021 | Standard Test Method for Evaluating PM<inf>2.5</inf> Sensors or Sensor Systems Used in Indoor Air Applications |
ASTM D 6796 : 2021 : EDT 1 | Standard Practice for Production of Coal, Coke and Coal Combustion Samples for Interlaboratory Studies |
ASTM B 923 : 2021 | Standard Test Method for Metal Powder Skeletal Density by Helium or Nitrogen Pycnometry |
ASTM D 6166 : 2012 : R2016 | Standard Test Method for Color of Pine Chemicals and Related Products (Instrumental Determination of Gardner Color) |
ASTM D 7115 : 2020 | Standard Test Method for Measurement of Superpave Gyratory Compactor (SGC) Internal Angle of Gyration Using Simulated Loading |
ASTM D 4678 : 2015 : REV A : R2019 | Standard Practice for Rubber—Preparation, Testing, Acceptance, Documentation, and Use of Reference Materials |
ASTM E 562 : 2019 : EDT 1 | Standard Test Method for Determining Volume Fraction by Systematic Manual Point Count |
ASTM D 5530 : 2015 | Standard Test Method for Total Moisture of Hazardous Waste Fuel by Karl Fischer Titrimetry |
ASTM E 2792 : 2013 | Standard Test Method for Determination of Hydrogen in Aluminum and Aluminum Alloys by Inert Gas Fusion |
ASTM D 4891 : 2013 : R2018 | Standard Test Method for Heating Value of Gases in Natural Gas and Flare Gases Range by Stoichiometric Combustion |
ASTM D 6234 : 2013 : R2020 | Standard Test Method for Shake Extraction of Mining Waste by the Synthetic Precipitation Leaching Procedure |
ASTM D 5147/D5147M : 2018 | Standard Test Methods for Sampling and Testing Modified Bituminous Sheet Material |
ASTM D 1353 : 2013 | Standard Test Method for Nonvolatile Matter in Volatile Solvents for Use in Paint, Varnish, Lacquer, and Related Products |
ASTM F 2150 : 2019 | Standard Guide for Characterization and Testing of Biomaterial Scaffolds Used in Regenerative Medicine and Tissue-Engineered Medical Products |
ASTM D 7736 : 2019 : REV A | Standard Test Method for Determination of Acids and Glycol Esters in Glycols |
ASTM D 3803 : 1991 : R2014 | Standard Test Method for Nuclear-Grade Activated Carbon |
ASTM E 2714 : 2013 : R2020 | Standard Test Method for Creep-Fatigue Testing |
ASTM D 8352 : 2020 | Standard Test Method for Determination of Relative Crystallinity of Zeolite Beta by X-Ray Diffraction |
ASTM D 7871 : 2019 | Standard Test Method for Analysis of Cyclohexane by Gas Chromatography (Effective Carbon Number) |
ASTM B 312 : 2020 | Standard Test Method for Green Strength of Specimens Compacted from Metal Powders |
ASTM C 518 : 2017 | Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus |
ASTM C 1327 : 2015 : R2019 | Standard Test Method for Vickers Indentation Hardness of Advanced Ceramics |
ASTM F 2634 : 2015 | Standard Test Method for Laboratory Testing of Polyethylene (PE) Butt Fusion Joints using Tensile-Impact Method |
ASTM F 3340 : 2018 | Standard Test Method for Thermal Resistance of Camping Mattresses Using a Guarded Hot Plate Apparatus |
ASTM C 830 : 2000 : R2016 | Standard Test Methods for Apparent Porosity, Liquid Absorption, Apparent Specific Gravity, and Bulk Density of Refractory Shapes by Vacuum Pressure |
ASTM E 2248 : 2018 | Standard Test Method for Impact Testing of Miniaturized Charpy V-notch Specimens |
ASTM F 2381 : 2019 | Standard Test Method for Evaluating Trans-Vinylene Yield in Irradiated Ultra-High Molecular Weight Polyethylene Fabricated Forms Intended for Surgical Implants by Infrared Spectroscopy |
ASTM D 2396 : 2020 | Standard Test Methods for Powder-Mix Time of Poly(Vinyl Chloride) (PVC) Resins Using a Torque Rheometer |
ASTM D 2862 : 2016 | Standard Test Method for Particle Size Distribution of Granular Activated Carbon |
ASTM G 180 : 2013 : R2019 | Standard Test Method for Corrosion Inhibiting Admixtures for Steel in Concrete by Polarization Resistance in Cementitious Slurries |
ASTM C 373 : 2018 | Standard Test Methods for Determination of Water Absorption and Associated Properties by Vacuum Method for Pressed Ceramic Tiles and Glass Tiles and Boil Method for Extruded Ceramic Tiles and Non-tile Fired Ceramic Whiteware Products |
ASTM E 3061 : 2017 | Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Inductively Coupled Plasma Atomic Emission Spectrometry (Performance Based Method) |
ASTM D 6387 : 2019 | Standard Test Methods for Composition of Turpentine and Related Terpene Products by Capillary Gas Chromatography |
ASTM E 2009 : 2008 : R2014 : EDT 1 | Standard Test Methods for Oxidation Onset Temperature of Hydrocarbons by Differential Scanning Calorimetry |
ASTM G 204 : 2015 | Standard Test Method for Damage to Contacting Solid Surfaces under Fretting Conditions |
ASTM D 7735 : 2017 | Standard Test Method for Type A Durometer Hardness Testing of Thermoplastic Pavement Marking at Elevated Temperatures |
ASTM D 3907/D3907M : 2019 | Standard Test Method for Testing Fluid Catalytic Cracking (FCC) Catalysts by Microactivity Test |
ASTM D 653 : 2021 | Standard Terminology Relating to Soil, Rock, and Contained Fluids |
ASTM D 3420 : 2014 | Standard Test Method for Pendulum Impact Resistance of Plastic Film |
ASTM D 6851 : 2020 | Standard Test Method for Determination of Contact pH with Activated Carbon |
ASTM F 2459 : 2018 | Standard Test Method for Extracting Residue from Metallic Medical Components and Quantifying via Gravimetric Analysis |
ASTM D 7710 : 2014 | Standard Test Method for Determination of Volume and Density of Rigid and Irregularly Shaped Molded Cellular Materials (Withdrawn 2021) |
ASTM D 1585 : 2015 : R2020 | Standard Test Methods for Fatty Acids Content of Pine Chemicals, Including Rosin, Tall Oil, and Related Products |
ASTM D 6259 : 2015 : R2019 | Standard Practice for Determination of a Pooled Limit of Quantitation for a Test Method |
ASTM C 1203 : 2004 : R2019 | Standard Test Method for Quantitative Determination of Alkali Resistance of a Ceramic-Glass Enamel |
ASTM D 4049 : 2020 | Standard Test Method for Determining the Resistance of Lubricating Grease to Water Spray |
ASTM D 6741 : 2010 : R2019 | Standard Test Methods for Silanes Used in Rubber Formulations<brk/>(bis-(triethoxysilylpropyl)sulfanes): Sulfur Content |
ASTM D 8036 : 2016 | Standard Test Method for Polyurethane Raw Materials: Determination of Dimer Ratio in Pure MDI |
ASTM D 1037 : 2012 : R2020 | Standard Test Methods for Evaluating Properties of Wood-Base Fiber and Particle Panel Materials |
ASTM D 7698 : 2020 | Standard Test Method for In-Place Estimation of Density and Water Content of Soil and Aggregate by Correlation with Complex Impedance Method |
ASTM D 4239 : 2018 : EDT 1 | Standard Test Method for Sulfur in the Analysis Sample of Coal and Coke Using High-Temperature Tube Furnace Combustion |
ASTM D 5470 : 2017 | Standard Test Method for Thermal Transmission Properties of Thermally Conductive Electrical Insulation Materials |
ASTM B 769 : 2011 : R2016 | Standard Test Method for Shear Testing of Aluminum Alloys |
ASTM F 1976 : 2013 | Standard Test Method for Impact Attenuation of Athletic Shoe Cushioning Systems and Materials (Withdrawn 2022) |
ASTM D 8176 : 2018 | Standard Test Method for Mechanically Tapped Density of Activated Carbon (Powdered and Fine Mesh) |
ASTM D 2777 : 2013 | Standard Practice for Determination of Precision and Bias of Applicable Test Methods of Committee D19 on Water |
ASTM F 1927 : 2020 | Standard Test Method for Determination of Oxygen Gas Transmission Rate, Permeability and Permeance at Controlled Relative Humidity Through Barrier Materials Using a Coulometric Detector |
ASTM G 51 : 2018 | Standard Test Method for Measuring pH of Soil for Use in Corrosion Testing |
ASTM D 4464 : 2015 : R2020 | Standard Test Method for Particle Size Distribution of Catalytic Materials by Laser Light Scattering |
ASTM D 1683/D1683M : 2017 : R2018 | Standard Test Method for Failure in Sewn Seams of Woven Fabrics |
ASTM D 6484/D6484M : 2020 | Standard Test Method for Open-Hole Compressive Strength of Polymer Matrix Composite Laminates |
ASTM D 2369 : 2020 | Standard Test Method for Volatile Content of Coatings |
ASTM G 134 : 2017 | Standard Test Method for Erosion of Solid Materials by Cavitating Liquid Jet |
ASTM B 946 : 2011 : R2016 | Standard Test Method for Surface Finish of Powder Metallurgy (PM) Products |
ASTM F 36 : 2015 | Standard Test Method for Compressibility and Recovery of Gasket Materials |
ASTM F 2214 : 2016 | Standard Test Method for <emph type="bdit">In Situ</emph> Determination of Network Parameters of Crosslinked Ultra High Molecular Weight Polyethylene (UHMWPE) |
ASTM D 7881 : 2020 : EDT 1 | Standard Test Method for Determination of 4-Carboxybenzaldehyde and <emph type="bdit" >p</emph>-Toluic Acid in Purified Terephthalic Acid by Capillary Electrophoresis with Reverse Voltage Mode |
ASTM C 835 : 2006 : R2020 | Standard Test Method for Total Hemispherical Emittance of Surfaces up to 1400°C |
ASTM D 6133 : 2002 : R2021 | Standard Test Method for Acetone, <emph type="ital">p</emph>-Chlorobenzotrifluoride, Methyl Acetate or <emph type="ital">t</emph>-Butyl Acetate Content of Solventborne and Waterborne Paints, Coatings, Resins, and Raw Materials by Direct Injection Into a Gas Chromatograph |
ASTM D 6479 : 2015 : R2020 | Standard Test Method for Determining the Edgecomb Resistance of Woven Fabrics Used in Inflatable Restraints |
ASTM G 156 : 2017 | Standard Practice for Selecting and Characterizing Weathering Reference Materials |
ASTM D 4355/D4355M : 2021 | Standard Test Method for Deterioration of Geotextiles by Exposure to Light, Moisture, and Heat in a Xenon Arc-Type Apparatus |
ASTM D 7918 : 2017 : REV A | Standard Test Method for Measurement of Flow Properties and Evaluation of Wear, Contaminants, and Oxidative Properties of Lubricating Grease by Die Extrusion Method and Preparation |
ASTM E 2301 : 2012 : R2017 | Standard Test Method for Daytime Colorimetric Properties of Fluorescent Retroreflective Sheeting and Marking Materials for High Visibility Traffic Control and Personal Safety Applications Using 45°:Normal Geometry |
ASTM E 1695 : 2020 | Standard Test Method for Measurement of Computed Tomography (CT) System Performance |
ASTM E 2187 : 2020 : REV A | Standard Test Method for Measuring the Ignition Strength of Cigarettes |
ASTM D 1790 : 2021 | Standard Test Method for Brittleness Temperature of Plastic Sheeting by Impact |
ASTM E 537 : 2020 | Standard Test Method for Thermal Stability of Chemicals by Differential Scanning Calorimetry |
ASTM D 3768 : 2016 | Standard Test Method for Microcellular Urethanes—Flexural Recovery |
ASTM D 638 : 2014 | Standard Test Method for Tensile Properties of Plastics |
ASTM D 6042 : 2009 : R2016 | Standard Test Method for Determination of Phenolic Antioxidants and Erucamide Slip Additives in Polypropylene Homopolymer Formulations Using Liquid Chromatography (LC) |
ASTM C 1182 : 2009(R2019) | Standard Test Method for Determining the Particle Size Distribution of Alumina by Centrifugal Photosedimentation |
ASTM A 1038 : 2019 | Standard Test Method for Portable Hardness Testing by the Ultrasonic Contact Impedance Method |
ASTM E 3097 : 2017 | Standard Test Method for Mechanical Uniaxial Constant Force Thermal Cycling of Shape Memory Alloys |
ASTM E 2832 : 2012 : R2017 | Standard Test Method for Measuring the Coefficient of Retroreflected Luminance of Pavement Markings in a Standard Condition of Continuous Wetting (R<inf>L-2</inf >) |
ASTM D 2638 : 2021 | Standard Test Method for Real Density of Calcined Petroleum Coke by Helium Pycnometer |
ASTM D 5824 : 1998 : R2017 | Standard Test Method for Determining Resistance to Delamination of Adhesive Bonds in Overlay-Wood Core Laminates Exposed to Heat and Water |
ASTM D 5628 : 2018 | Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimens by Means of a Falling Dart (Tup or Falling Mass) |
ASTM B 648 : 2010 : R2015 : EDT 1 | Standard Test Method for Indentation Hardness of Aluminum Alloys by Means of a Barcol Impressor |
ASTM E 1834 : 2018 | Standard Test Method for Analysis of Nickel Alloys by Graphite Furnace Atomic Absorption Spectrometry |
ASTM E 991 : 2016 | Standard Practice for Color Measurement of Fluorescent Specimens Using the One-Monochromator Method |
ASTM F 2607 : 2008 : R2014 | Standard Test Method for Measuring the Hard Surface Floor-Cleaning Ability of Household/Commercial Vacuum Cleaners |
ASTM C 1559 : 2015 | Standard Test Method for Determining Wicking of Fibrous Glass Blanket Insulation (Aircraft Type) |
ASTM F 2828 : 2020 | Standard Test Method for Assessing Carpet Cleaning Effectiveness in Terms of Visual Appearance Change When Cleaned with a Wet Extraction Cleaning System |
ASTM D 5158 : 1998 : R2019 | Standard Test Method for Determination of Particle Size of Powdered Activated Carbon by Air-Jet Sieving |
ASTM F 1334 : 2018 | Standard Test Method for Determining A-Weighted Sound Power Level of Vacuum Cleaners |
ASTM D 6886 : 2018 | Standard Test Method for Determination of the Weight Percent Individual Volatile Organic Compounds in Waterborne Air-Dry Coatings by Gas Chromatography |
ASTM D 1004 : 2021 | Standard Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting |
ASTM E 1868 : 2010 : R2015 | Standard Test Methods for Loss-On-Drying by Thermogravimetry |
ASTM F 2004 : 2017 | Standard Test Method for Transformation Temperature of Nickel-Titanium Alloys by Thermal Analysis |
ASTM C 1279 : 2013 : R2019 | Standard Test Method for Non-Destructive Photoelastic Measurement of Edge and Surface Stresses in Annealed, Heat-Strengthened, and Fully Tempered Flat Glass |
ASTM D 3574 : 2017 | Standard Test Methods for Flexible Cellular Materials—Slab, Bonded, and Molded Urethane Foams |
ASTM D 7967 : 2016 | Standard Test Method for Analysis of Chrome Content (as Cr<inf>2</inf>O<inf>3</inf>) in Wet Blue using Atomic Absorption |
ASTM E 2603 : 2015 | Standard Practice for Calibration of Fixed-Cell Differential Scanning Calorimeters |
ASTM F 1914 : 2018 | Standard Test Methods for Short-Term Indentation and Residual Indentation of Resilient Floor Covering |
ASTM D 5504 : 2020 | Standard Test Method for Determination of Sulfur Compounds in Natural Gas and Gaseous Fuels by Gas Chromatography and Chemiluminescence |
ASTM D 8087 : 2018 | Standard Test Method for Color of Maleic Anhydride in the Molten State and After Heating (Platinum-Cobalt Scale) Using Tristimulus Colorimetry |
ASTM C 1134 : 2017 | Standard Test Method for Water Retention of Rigid Thermal Insulations Following Partial Immersion |
ASTM F 1978 : 2018 | Standard Test Method for Measuring Abrasion Resistance of Metallic Thermal Spray Coatings by Using the Taber Abraser |
ASTM D 4567 : 2019 | Standard Test Method for Single-Point Determination of Specific Surface Area of Catalysts and Catalyst Carriers Using Nitrogen Adsorption by Continuous Flow Method |
ASTM D 7305 : 2008 : REV A : R2020 | Standard Test Method for Reflection Density of Printed Matter |
ASTM D 7234 : 2019 | Standard Test Method for Pull-Off Adhesion Strength of Coatings on Concrete Using Portable Pull-Off Adhesion Testers |
ASTM D 953 : 2019 | Standard Test Method for Pin-Bearing Strength of Plastics |
ASTM F 970 : 2017 | Standard Test Method for Measuring Recovery Properties of Floor Coverings after Static Loading |
ASTM D 7148 : 2019 : REV A | Standard Test Method for Determining the Ionic Resistivity (ER) of Alkaline Battery Separator Using a Carbon Electrode in an Electrolyte Bath Measuring System |
ASTM C 1733 : 2020 | Standard Test Method for Distribution Coefficients of Inorganic Species by Batch Method |
ASTM C 307 : 2018 | Standard Test Method for Tensile Strength of Chemical-Resistant Mortar, Grouts, and Monolithic Surfacings |
ASTM F 2199 : 2020 | Standard Test Method for Determining Dimensional Stability and Curling Properties of Resilient Flooring after Exposure to Heat |
ASTM C 198 : 2009 : R2019 | Standard Test Method for Cold Bonding Strength of Refractory Mortar |
ASTM D 695 : 2015 | Standard Test Method for Compressive Properties of Rigid Plastics |
ASTM B 761 : 2017 | Standard Test Method for Particle Size Distribution of Metal Powders and Related Compounds by X-Ray Monitoring of Gravity Sedimentation |
ASTM D 7315 : 2017 | Standard Test Method for Determination of Turbidity Above 1 Turbidity Unit (TU) in Static Mode |
ASTM D 6818 : 2021 | Standard Test Method for Tensile Properties of Rolled Erosion Control Products |
ASTM F 3139 : 2015 | Standard Test Method for Analysis of Tin-Based Solder Alloys for Minor and Trace Elements Using Inductively Coupled Plasma Atomic Emission Spectrometry |
ASTM G 151 : 2019 | Standard Practice for Exposing Nonmetallic Materials in Accelerated Test Devices that Use Laboratory Light Sources |
ASTM D 3366 : 2018 | Standard Test Method for Color of Maleic Anhydride in the Molten State and After Heating (Platinum-Cobalt Scale) |
ASTM D 5045 : 2014 | Standard Test Methods for Plane-Strain Fracture Toughness and Strain Energy Release Rate of Plastic Materials |
ASTM D 4164 : 2013 : R2018 | Standard Test Method for Mechanically Tapped Packing Density of Formed Catalyst and Catalyst Carriers |
ASTM D 4475 : 2002 : R2016 | Standard Test Method for Apparent Horizontal Shear Strength of Pultruded Reinforced Plastic Rods By the Short-Beam Method |
ASTM D 8063 : 2018 | Standard Test Method for Water in Purified Terephthalic Acid (PTA) by Volumetric Karl Fischer Titration |
ASTM C 474 : 2015 : R2020 | Standard Test Methods for Joint Treatment Materials for Gypsum Board Construction |
ASTM D 3361/D3361M : 2013 : R2018 | Standard Practice for Unfiltered Open-Flame Carbon-Arc Exposures of Paint and Related Coatings |
ASTM D 2463 : 2015 | Standard Test Method for Drop Impact Resistance of Blow-Molded Thermoplastic Containers |
ASTM F 1888 : 2009 : R2016 | Standard Test Method for Compression-Displacement of Baseballs and Softballs |
ASTM D 4350 : 2016 | Standard Test Method for Corrosivity Index of Plastics and Fillers |
ASTM E 2274 : 2016 | Standard Test Method for Evaluation of Laundry Sanitizers and Disinfectants |
ASTM D 8243 : 2019 | Standard Test Method for Determination of APS Reductase to Estimate Sulfate Reducing Bacterial Bioburdens in Water – Enzyme-Linked Immunosorbent Assay Method |
ASTM G 153 : 2013 | Standard Practice for Operating Enclosed Carbon Arc Light Apparatus for Exposure of Nonmetallic Materials |
ASTM E 3165 : 2018 | Standard Test Method for Nighttime Retroreflected Chromaticity of Retroreflective Sheeting |
ASTM D 2799 : 2013 | Standard Test Method for Microscopical Determination of the Maceral Composition of Coal |
ASTM C 1363 : 2019 | Standard Test Method for Thermal Performance of Building Materials and Envelope Assemblies by Means of a Hot Box Apparatus |
ASTM D 5155 : 2019 | Standard Test Methods for Polyurethane Raw Materials: Determination of the Isocyanate Content of Aromatic Isocyanates |
ASTM D 5228 : 2016 | Standard Test Method for Determination of Butane Working Capacity of Activated Carbon |
ASTM D 6032/D6032M : 2017 | Standard Test Method for Determining Rock Quality Designation (RQD) of Rock Core |
ASTM D 8032 : 2020 | Standard Test Method for Acid Number of Terephthalic Acid by Color-Indicator Titration |
ASTM D 6657 : 2016 | Standard Test Method for pH of Wet Blue and Wet White |
ASTM D 7359 : 2018 | Standard Test Method for Total Fluorine, Chlorine and Sulfur in Aromatic Hydrocarbons and Their Mixtures by Oxidative Pyrohydrolytic Combustion followed by Ion Chromatography Detection (Combustion Ion Chromatography-CIC) |
ASTM D 4463/D4463M : 2019 | Standard Guide for Metals Free Steam Deactivation of Fresh Fluid Cracking Catalysts |
ASTM G 65 : 2016 : EDT 1 | Standard Test Method for Measuring Abrasion Using the Dry Sand/Rubber Wheel Apparatus |
ASTM E 606/E606M : 2019 : EDT 1 | Standard Test Method for Strain-Controlled Fatigue Testing |
ASTM D 7830/D7830M : 2014 | Standard Test Method for In-Place Density (Unit Weight) and Water Content of Soil Using an Electromagnetic Soil Density Gauge |
ASTM D 8130 : 2017 | Standard Test Method for Determination of Metals in Purified Terephthalic Acid (PTA) by Inductively Coupled Plasma Atomic Emission Spectrometric Method |
ASTM D 3576 : 2020 | Standard Test Method for Cell Size of Rigid Cellular Plastics |
ASTM D 2412 : 2021 | Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading |
ASTM D 7542 : 2015 | Standard Test Method for Air Oxidation of Carbon and Graphite in the Kinetic Regime |
ASTM F 1863 : 2016 | Standard Test Method for Measuring the Night Vision Goggle-Weighted Transmissivity of Transparent Parts |
ASTM G 67 : 2018 | Standard Test Method for Determining the Susceptibility to Intergranular Corrosion of 5XXX Series Aluminum Alloys by Mass Loss After Exposure to Nitric Acid (NAMLT Test) |
ASTM D 6973 : 2014 : R2019 | Standard Test Method for Indicating Wear Characteristics of Petroleum Hydraulic Fluids in a High Pressure Constant Volume Vane Pump |
ASTM E 2540 : 2016 : EDT 1 | Standard Test Method for Measurement of Retroreflective Signs Using a Portable Retroreflectometer at a 0.5 Degree Observation Angle |
ASTM E 1617 : 2009 : R2019 | Standard Practice for Reporting Particle Size Characterization Data |
ASTM D 5672/D5672M : 2015 | Standard Test Method for Testing Flexible Cellular Materials Measurement of Indentation Force Deflection Using a 25-mm [1-in.] Deflection Technique |
ASTM D 7937 : 2015 | Standard Test Method for In-situ Determination of Turbidity Above 1 Turbidity Unit (TU) in Surface Water |
ASTM D 7823 : 2020 | Standard Test Method for Determination of Low Level Phthalates in Poly (Vinyl Chloride) Plastics by Thermal Desorption—Gas Chromatography/Mass Spectrometry |
ASTM C 604 : 2018 | Standard Test Method for True Specific Gravity of Refractory Materials by Gas-Comparison Pycnometer |
ASTM D 6299 : 2020 : REV A | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
ASTM D 3418 : 2015 | Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry |
ASTM D 1725 : 2012 : R2019 | Standard Practice for Preparing Resin Solutions for Viscosity Measurement by Bubble Time Method |
ASTM D 7819 : 2012 : R2016 | Standard Test Method for Enumeration of Yeast and Mold on Fresh (Uncured) Hides and Skins |
ASTM F 735 : 2017 | Standard Test Method for Abrasion Resistance of Transparent Plastics and Coatings Using the Oscillating Sand Method |
ASTM C 1785 : 2017 | Standard Test Method for Concentration of Pinhole Detections in Moisture Barriers on Metal Jacketing |
ASTM D 8356 : 2020 | Standard Test Method for Sonic Velocity in Manufactured Carbons and Graphite Materials for use in Obtaining Approximate Elastic Constants: Young’s Modulus, Shear Modulus, and Poisson’s Ratio |
ASTM D 3273 : 2016 | Standard Test Method for Resistance to Growth of Mold on the Surface of Interior Coatings in an Environmental Chamber |
ASTM G 181 : 2011 : R2017 | Standard Test Method for Conducting Friction Tests of Piston Ring and Cylinder Liner Materials Under Lubricated Conditions |
ASTM E 970 : 2017 | Standard Test Method for Critical Radiant Flux of Exposed Attic Floor Insulation Using a Radiant Heat Energy Source |
ASTM D 7283 : 2017 | Standard Test Method for Alpha and Beta Activity in Water By Liquid Scintillation Counting |
ASTM E 1640 : 2018 | Standard Test Method for Assignment of the Glass Transition Temperature By Dynamic Mechanical Analysis |
ASTM F 386 : 2017 | Standard Test Method for Thickness of Resilient Flooring Materials Having Flat Surfaces |
ASTM D 127 : 2019 | Standard Test Method for Drop Melting Point of Petroleum Wax, Including Petrolatum |
ASTM D 2578 : 2017 | Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films |
ASTM D 3663 : 2020 | Standard Test Method for Surface Area of Catalysts and Catalyst Carriers |
ASTM D 6641/D6641M : 2016 : EDT 1 | Standard Test Method for Compressive Properties of Polymer Matrix Composite Materials Using a Combined Loading Compression (CLC) Test Fixture |
ASTM B 214 : 2016 | Standard Test Method for Sieve Analysis of Metal Powders |
ASTM D 7151 : 2015 | Standard Test Method for Determination of Elements in Insulating Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) |
ASTM D 1000 : 2017 | Standard Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications |
ASTM D 2305 : 2018 | Standard Test Methods for Polymeric Films Used for Electrical Insulation |
ASTM D 4884/D4884M : 2014 : REV A | Standard Test Method for Strength of Sewn or Bonded Seams of Geotextiles |
ASTM D 7005/D7005M : 2016 | Standard Test Method for Determining the Bond Strength (Ply Adhesion) of Geocomposites |
ASTM D 5420 : 2021 | Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact) |
ASTM D 6656 : 2016 | Standard Test Method for Determination of Chromic Oxide in Wet Blue (Perchloric Acid Oxidation) |
ASTM D 3103 : 2020 | Standard Test Method for Thermal Insulation Performance of Distribution Packages |
ASTM D 7682 : 2017 | Standard Test Method for Replication and Measurement of Concrete Surface Profiles Using Replica Putty |
ASTM F 2082/F2082M : 2016 | Standard Test Method for Determination of Transformation Temperature of Nickel-Titanium Shape Memory Alloys by Bend and Free Recovery |
ASTM E 3151 : 2018 | Standard Test Method for Determining Antimicrobial Activity and Biofilm Resistance Properties of Tube, Yarn, or Fiber Specimens |
ASTM D 6463/D6463M : 2006 : R2020 | Standard Test Method for Time to Failure of Pressure Sensitive Articles Under Sustained Shear Loading |
ASTM D 3795 : 2020 | Standard Test Method for Thermal Flow, Cure, and Behavior Properties of Pourable Thermosetting Materials by Torque Rheometer |
ASTM F 3299 : 2018 | Standard Test Method for Water Vapor Transmission Rate Through Plastic Film and Sheeting Using an Electrolytic Detection Sensor (Coulometric P<inf>2</inf>O<inf >5</inf> Sensor) |
ASTM D 7570 : 2017 | Standard Test Method for Evaluation of Dimensional Stability of Pile Yarn Floor Covering |
ASTM D 7582 : 2015 | Standard Test Methods for Proximate Analysis of Coal and Coke by Macro Thermogravimetric Analysis |
ASTM D 4204 : 2016 | Standard Practice for Preparing Plastic Film Specimens for a Round-Robin Study |
ASTM E 3047 : 2016 | Standard Test Method for Analysis of Nickel Alloys by Spark Atomic Emission Spectrometry |
ASTM F 1802 : 2015 | Standard Test Method for Performance Testing of Excess Flow Valves |
ASTM D 7681 : 2011 : R2016 : EDT 1 | Standard Test Method for Measuring Gradation of Glass Spheres Using a Flowing Stream Digital Image Analyzer |
ASTM G 98 : 2017 | Standard Test Method for Galling Resistance of Materials |
ASTM F 801 : 2016 | Standard Test Method for Measuring Optical Angular Deviation of Transparent Parts |
ASTM C 802 : 2014 | Standard Practice for Conducting an Interlaboratory Test Program to Determine the Precision of Test Methods for Construction Materials |
ASTM G 141 : 2009 : R2013 | Standard Guide for Addressing Variability in Exposure Testing of Nonmetallic Materials |
ASTM E 92 : 2017 | Standard Test Methods for Vickers Hardness and Knoop Hardness of Metallic Materials |
ASTM D 6902 : 2004 : R2017 | Standard Test Method for Laboratory Measurement of Formaldehyde Evolved During the Curing of Melamine-Formaldehyde-Based Coatings |
ASTM D 7047 : 2015 : EDT 1 | Standard Test Method for Swell Volume of Plantago Insularis (Ovata, Psyllium) |
ASTM D 494 : 2011(R2019) | Standard Test Method for Acetone Extraction of Phenolic Molded or Laminated Products |
ASTM D 1412/D1412M : 2020 | Standard Test Method for Equilibrium Moisture of Coal at 96 to 97 Percent Relative Humidity and 30 °C |
ASTM D 1525 : 2017 : EDT 1 | Standard Test Method for Vicat Softening Temperature of Plastics |
ASTM E 2860 : 2020 | Standard Test Method for Residual Stress Measurement by X-Ray Diffraction for Bearing Steels |
ASTM D 2658 : 2018 | Standard Test Method for Determining Dimensions of Fiberboard Boxes |
ASTM D 5341/D5341M : 2019 | Standard Test Method for Measuring Coke Reactivity Index (CRI) and Coke Strength After Reaction (CSR) |
ASTM D 7391 : 2020 | Standard Test Method for Categorization and Quantification of Airborne Fungal Structures in an Inertial Impaction Sample by Optical Microscopy |
ASTM C 1819 : 2015 | Standard Test Method for Hoop Tensile Strength of Continuous Fiber-Reinforced Advanced Ceramic Composite Tubular Test Specimens at Ambient Temperature Using Elastomeric Inserts |
ASTM F 1276 : 1999 : R2016 | Standard Test Method for Creep Relaxation of Laminated Composite Gasket Materials |
ASTM B 975 : 2018 : EDT 1 | Standard Test Method for Measurement of Internal Stress of Metallic Coatings by Split Strip Evaluation (Deposit Stress Analyzer Method) |
ASTM E 1545 : 2011 : R2016 | Standard Test Method for Assignment of the Glass Transition Temperature by Thermomechanical Analysis |
ASTM D 6476 : 2012 : R2017 : EDT 1 | Standard Test Method for Determining Dynamic Air Permeability of Inflatable Restraint Fabrics |
ASTM D 5831 : 2017 | Standard Practice for Screening Fuels in Soils |
ASTM D 7811 : 2013 : R2017 | Standard Test Method for Bow and Skew Using a Measuring Tool |
ASTM F 3022 : 2016 : EDT 1 | Standard Test Method for Evaluating the Universal Design of Fitness Equipment for Inclusive Use by Persons with Functional Limitations and Impairments |
ASTM E 1710 : 2018 | Standard Test Method for Measurement of Retroreflective Pavement Marking Materials with CEN-Prescribed Geometry Using a Portable Retroreflectometer |
ASTM F 1930 : 2018 | Standard Test Method for Evaluation of Flame-Resistant Clothing for Protection Against Fire Simulations Using an Instrumented Manikin |
ASTM E 1590 : 2017 | Standard Test Method for Fire Testing of Mattresses |
ASTM G 72/G72M : 2015 | Standard Test Method for Autogenous Ignition Temperature of Liquids and Solids in a High-Pressure Oxygen-Enriched Environment |
ASTM E 2298 : 2018 | Standard Test Method for Instrumented Impact Testing of Metallic Materials |
ASTM D 7639 : 2010 : R2018 | Standard Test Method for Determination of Zirconium Treatment Weight or Thickness on Metal Substrates by X-Ray Fluorescence |
ASTM D 4280 : 2018 | Standard Specification for Extended Life Type, Nonplowable, Raised Retroreflective Pavement Markers |
ASTM F 88/F88M : 2015 | Standard Test Method for Seal Strength of Flexible Barrier Materials |
ASTM D 7056 : 2007 : R2018 | Standard Test Method for Determining the Tensile Shear Strength of Prefabricated Bituminous Geomembrane Seams |
ASTM E 2627 : 2013 : R2019 | Standard Practice for Determining Average Grain Size Using Electron Backscatter Diffraction (EBSD) in Fully Recrystallized Polycrystalline Materials |
ASTM C 721 : 2020 | Standard Test Methods for Estimating Average Particle Size of Alumina and Silica Powders by Air Permeability |
ASTM E 1450 : 2016 | Standard Test Method for Tension Testing of Structural Alloys in Liquid Helium |
ASTM E 292 : 2018 | Standard Test Methods for Conducting Time-for-Rupture Notch Tension Tests of Materials |
ASTM D 5017 : 2017 | Standard Test Method for Determination of Linear Low Density Polyethylene (LLDPE) Composition by Carbon-13 Nuclear Magnetic Resonance |
ASTM G 109 : 2007 : R2013 | Standard Test Method for Determining Effects of Chemical Admixtures on Corrosion of Embedded Steel Reinforcement in Concrete Exposed to Chloride Environments |
ASTM G 123 : 2000 : R2015 | Standard Test Method for Evaluating Stress-Corrosion Cracking of Stainless Alloys with Different Nickel Content in Boiling Acidified Sodium Chloride Solution |
ASTM D 4883 : 2018 | Standard Test Method for Density of Polyethylene by the Ultrasound Technique |
ASTM F 2961 : 2015 | Standard Test Method for Characterizing Gripping Performance of Gloves Using a Torque Meter |
ASTM D 7454 : 2019 | Standard Test Method for Determination of Vibrated Bulk Density of Calcined Petroleum Coke using a Semi-Automated Apparatus |
ASTM D 5071 : 2006 : R2013 | Standard Practice for Exposure of Photodegradable Plastics in a Xenon Arc Apparatus |
ASTM D 5836 : 2020 | Standard Test Method for Determination of 2,4-Toluene Diisocyanate (2,4-TDI) and 2,6-Toluene Diisocyanate (2,6-TDI) in Workplace Atmospheres (1-2 PP Method) |
ASTM D 4213 : 2008 : R2016 | Standard Test Method for Scrub Resistance of Paints by Abrasion Weight Loss |
ASTM D 6559 : 2000 : REV A : R2016 : EDT 1 | Standard Test Method for Determination of Thermogravimetric (TGA) Air Reactivity of Baked Carbon Anodes and Cathode Blocks |
ASTM C 1275 : 2018 | Standard Test Method for Monotonic Tensile Behavior of Continuous Fiber-Reinforced Advanced Ceramics with Solid Rectangular Cross-Section Test Specimens at Ambient Temperature |
ASTM F 3107 : 2014 | Standard Test Method for Measuring Accuracy after Mechanical Disturbances on Reference Frames of Computer Assisted Surgery Systems |
ASTM D 6743 : 2020 | Standard Test Method for Thermal Stability of Organic Heat Transfer Fluids |
ASTM E 2399/E2399M : 2019 | Standard Test Method for Maximum Media Density for Dead Load Analysis of Vegetative (Green) Roof Systems |
ASTM G 32 : 2016 | Standard Test Method for Cavitation Erosion Using Vibratory Apparatus |
ASTM F 519 : 2018 | Standard Test Method for Mechanical Hydrogen Embrittlement Evaluation of Plating/Coating Processes and Service Environments |
ASTM D 7488 : 2011 : R2016 | Standard Test Method for Open Time of Latex Paints |
ASTM D 5629 : 2016 | Standard Test Method for Polyurethane Raw Materials: Determination of Acidity in Low-Acidity Aromatic Isocyanates and Polyurethane Prepolymers |
ASTM B 922 : 2020 | Standard Test Method for Metal Powder Specific Surface Area by Physical Adsorption |
ASTM D 6109 : 2019 | Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastic Lumber and Related Products |
ASTM D 1894 : 2014 | Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting (Withdrawn 2023) |
ASTM F 1608 : 2016 | Standard Test Method for Microbial Ranking of Porous Packaging Materials (Exposure Chamber Method) |
ASTM D 6740 : 2015 : R2019 | Standard Test Method for Silanes Used in Rubber Formulations<brk/>(bis-(triethoxysilylpropyl)sulfanes): Residue on Ignition |
ASTM D 7426 : 2008 : R2013 | Standard Test Method for Assignment of the DSC Procedure for Determining T<inf>g</inf > of a Polymer or an Elastomeric Compound (Withdrawn 2022) |
ASTM D 7309 : 2020 | Standard Test Method for Determining Flammability Characteristics of Plastics and Other Solid Materials Using Microscale Combustion Calorimetry |
ASTM E 1085 : 2016 | Standard Test Method for Analysis of Low-Alloy Steels by Wavelength Dispersive X-Ray Fluorescence Spectrometry |
ASTM B 934 : 2015 | Standard Test Method for Effective Case Depth of Ferrous Powder Metallurgy (PM) Parts Using Microindentation Hardness Measurements |
ASTM D 7607/D7607M : 2019 | Standard Test Method for Analysis of Oxygen in Gaseous Fuels (Electrochemical Sensor Method) |
ASTM F 2878 : 2019 | Standard Test Method for Protective Clothing Material Resistance to Hypodermic Needle Puncture |
ASTM B 557 : 2015 | Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products |
ASTM D 5386 : 2016 | Standard Test Method for Color of Liquids Using Tristimulus Colorimetry |
ASTM D 3354 : 2015 | Standard Test Method for Blocking Load of Plastic Film by the Parallel Plate Method |
ASTM F 791 : 2018 | Standard Test Method for Stress Crazing of Transparent Plastics |
ASTM D 8271 : 2021 | Standard Test Method for the Direct Measurement of Surface Profile of Prepared Concrete |
ASTM D 8117 : 2017 | Standard Test Method for Oxidative Induction Time of Polyolefin Geosynthetics by Differential Scanning Calorimetry |
ASTM D 7191 : 2018 | Standard Test Method for Determination of Moisture in Plastics by Relative Humidity Sensor |
ASTM D 5891/D5891M : 2019 | Standard Test Method for Fluid Loss of Clay Component of Geosynthetic Clay Liners |
ASTM D 4275 : 2017 | Standard Test Method for Determination of Butylated Hydroxy Toluene (BHT) in Polymers of Ethylene and Ethylene–Vinyl Acetate (EVA) Copolymers by Gas Chromatography |
ASTM D 8031 : 2016 | Standard Test Method for Acid Number of Terephthalic Acid (TA) by Automatic Potentiometric Titration |
ASTM F 3203 : 2019 | Standard Test Method for Determination of Gel Content of Crosslinked Polyethylene (PEX) Pipes and Tubing |
ASTM E 1352 : 2016 | Standard Test Method for Cigarette Ignition Resistance of Mock-Up Upholstered Furniture Assemblies (Withdrawn 2022) |
ASTM D 7816 : 2012 : R2016 | Standard Test Method for Enumeration of Halophilic and Proteolytic Bacteria in Raceway Brine, Brine-Cured Hides and Skins |
ASTM F 2466 : 2010 : R2018 | Standard Practice for Determining Silicone Volatiles in Silicone Rubber for Transportation Applications |
ASTM D 3288/D3288M : 2020 | Standard Test Methods for Magnet-Wire Enamels |
ASTM D 7310 : 2020 | Standard Practice for Defect Detection and Rating of Plastic Films Using Optical Sensors |
ASTM F 2102 : 2017 | Standard Guide for Evaluating the Extent of Oxidation in Polyethylene Fabricated Forms Intended for Surgical Implants |
ASTM D 924 : 2015 | Standard Test Method for Dissipation Factor (or Power Factor) and Relative Permittivity (Dielectric Constant) of Electrical Insulating Liquids |
ASTM F 146 : 2012 : R2019 : EDT 1 | Standard Test Methods for Fluid Resistance of Gasket Materials |
ASTM E 1875 : 2020 | Standard Test Method for Dynamic Young's Modulus, Shear Modulus, and Poisson's Ratio by Sonic Resonance |
ASTM C 1365 : 2018 | Standard Test Method for Determination of the Proportion of Phases in Portland Cement and Portland-Cement Clinker Using X-Ray Powder Diffraction Analysis |
ASTM D 7245 : 2009 : R2021 | Standard Test Method for Measuring Total Water and Volatiles in Liquid Coatings Which Produce Cure Water Upon Heating |
ASTM C 534/C534M : 2020 : REV A | Standard Specification for Preformed Flexible Elastomeric Cellular Thermal Insulation in Sheet and Tubular Form |
ASTM D 2457 : 2013 | Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics |
ASTM E 2890 : 2012 : R2018 | Standard Test Method for Kinetic Parameters for Thermally Unstable Materials by Differential Scanning Calorimetry Using the Kissinger Method |
ASTM D 822/D822M : 2013 : R2018 | Standard Practice for Filtered Open-Flame Carbon-Arc Exposures of Paint and Related Coatings |
ASTM B 557M : 2015 | Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products (Metric) |
ASTM D 4875 : 2018 | Standard Test Methods of Polyurethane Raw Materials: Determination of the Polymerized Ethylene Oxide Content of Polyether Polyols |
ASTM G 16 : 2013 : R2019 | Standard Guide for Applying Statistics to Analysis of Corrosion Data |
ASTM D 7584 : 2016 | Standard Test Method for Evaluating the Resistance of the Surface of Wet Blue and Wet White to the Growth of Fungi in an Environmental Chamber |
ASTM D 3682 : 2013 | Standard Test Method for Major and Minor Elements in Combustion Residues from Coal Utilization Processes |
ASTM C 372 : 1994 : R2020 | Standard Test Method for Linear Thermal Expansion of Porcelain Enamel and Glaze Frits and Fired Ceramic Whiteware Products by Dilatometer Method |
ASTM D 4699 : 2003 : R2018 : EDT 1 | Standard Test Method for Vibratory Packing Density of Large Formed Catalyst and Catalyst Carrier Particles |
ASTM D 5776 : 2014 : REV A | Standard Test Method for Bromine Index of Aromatic Hydrocarbons by Electrometric Titration |
ASTM D 6053 : 2014 : R2018 | Standard Test Method for Determination of Volatile Organic Compound (VOC) Content of Electrical Insulating Varnishes |
ASTM F 2192 : 2005 : R2017 | Standard Test Method for Determining and Reporting the Berthing Energy and Reaction of Marine Fenders |
ASTM D 7380 : 2015 | Standard Test Method for Soil Compaction Determination at Shallow Depths Using 5-lb (2.3 kg) Dynamic Cone Penetrometer |
ASTM D 5649 : 2015 | Standard Test Method for Torque Strength of Adhesives Used on Threaded Fasteners |
ASTM G 97 : 2018 | Standard Test Method for Laboratory Evaluation of Magnesium Sacrificial Anode Test Specimens for Underground Applications |
ASTM D 3012 : 2019 | Standard Test Method for Thermal-Oxidative Stability of Polypropylene Using a Specimen Rotator Within an Oven |
ASTM D 8097 : 2017:EDT 1 | Standard Test Method for Determination of Bulk Density for Specific Size Fractions of Calcined Petroleum Coke Using a Transaxial Pressure Pycnometer |
ASTM D 2166/D2166M : 2016 | Standard Test Method for Unconfined Compressive Strength of Cohesive Soil |
ASTM E 2536 : 2015 : REV A | Standard Guide for Assessment of Measurement Uncertainty in Fire Tests |
ASTM D 6290 : 2019 | Standard Test Method for Color Determination of Plastic Pellets |
ASTM D 6142 : 2016 | Standard Test Method for Analysis of Phenol by Capillary Gas Chromatography |
ASTM C 522 : 2003 : R2016 | Standard Test Method for Airflow Resistance of Acoustical Materials |
ASTM C 1341 : 2013 : R2018 | Standard Test Method for Flexural Properties of Continuous Fiber-Reinforced Advanced Ceramic Composites |
ASTM C 20 : 2000 : R2015 | Standard Test Methods for Apparent Porosity, Water Absorption, Apparent Specific Gravity, and Bulk Density of Burned Refractory Brick and Shapes by Boiling Water |
ASTM D 4735 : 2019 | Standard Test Method for Determination of Trace Thiophene in Refined Benzene by Gas Chromatography |
ASTM C 267 : 2020 | Standard Test Methods for Chemical Resistance of Mortars, Grouts, and Monolithic Surfacings and Polymer Concretes |
ASTM G 139 : 2005 : R2015 | Standard Test Method for Determining Stress-Corrosion Cracking Resistance of Heat-Treatable Aluminum Alloy Products Using Breaking Load Method |
ASTM D 5974 : 2020 | Standard Test Methods for Fatty and Rosin Acids in Tall Oil Fractionation Products by Capillary Gas Chromatography |
ASTM D 6360 : 2015 | Standard Practice for Enclosed Carbon-Arc Exposures of Plastics |
ASTM D 6316 : 2017 | Standard Test Method for Determination of Total, Combustible and Carbonate Carbon in Solid Residues from Coal and Coke |
ASTM D 4789 : 2020 : EDT 1 | Standard Test Method for Solution Color of Bisphenol A (4,4<emph type="ital">′</emph >-Isopropylidenediphenol) |
ASTM G 77 : 2017 | Standard Test Method for Ranking Resistance of Materials to Sliding Wear Using Block-on-Ring Wear Test |
ASTM D 6478 : 2010 : R2019 | Standard Test Method for Determining Specific Packability of Fabrics Used in Inflatable Restraints |
ASTM E 2584 : 2020 | Standard Practice for Thermal Conductivity of Materials Using a Thermal Capacitance (Slug) Calorimeter |
ASTM E 1356 : 2008 : R2014 | Standard Test Method for Assignment of the Glass Transition Temperatures by Differential Scanning Calorimetry (Withdrawn 2023) |
ASTM D 7521 : 2016 | Standard Test Method for Determination of Asbestos in Soil |
ASTM D 7707 : 2011 : R2016 | Standard Specification for Wipe Sampling Materials for Beryllium in Surface Dust |
ASTM C 1511 : 2015 | Standard Test Method for Determining the Water Retention (Repellency) Characteristics of Fibrous Glass Insulation (Aircraft Type) |
ASTM D 720/D720M : 2015 : EDT 1 | Standard Test Method for Free-Swelling Index of Coal |
ASTM D 7183 : 2018 : REV A : EDT 1 | Standard Test Method for Determination of Total Sulfur in Aromatic Hydrocarbons and Related Chemicals by Ultraviolet Fluorescence |
ASTM E 1782 : 2014 | Standard Test Method for Determining Vapor Pressure by Thermal Analysis |
ASTM D 4483 : 2020 | Standard Practice for Evaluating Precision for Test Method Standards in the Rubber and Carbon Black Manufacturing Industries |
ASTM F 1292 : 2018 : EDT 1 | Standard Specification for Impact Attenuation of Surfacing Materials Within the Use Zone of Playground Equipment |
ASTM E 766 : 2014(R2019) | Standard Practice for Calibrating the Magnification of a Scanning Electron Microscope |
ASTM D 7414 : 2018 | Standard Test Method for Condition Monitoring of Oxidation in In-Service Petroleum and Hydrocarbon Based Lubricants by Trend Analysis Using Fourier Transform Infrared (FT-IR) Spectrometry |
ASTM C 1774 : 2013 : R2019 | Standard Guide for Thermal Performance Testing of Cryogenic Insulation Systems |
ASTM F 3375 : 2019 | Standard Test Method for Assessing Non-Metered Restricted Delivery Systems for Liquid Consumer Products |
ASTM D 7237 : 2018 | Standard Test Method for Free Cyanide and Aquatic Free Cyanide with Flow Injection Analysis (FIA) Utilizing Gas Diffusion Separation and Amperometric Detection |
ASTM D 8007 : 2015 : R2019 | Standard Test Method for Wale and Course Count of Weft Knitted Fabrics |
ASTM D 8161 : 2017 | Standard Test Method for Impact Resistance of Thermoplastic Pavement Marking Materials over a Highway Substrate by Means of a Striker Impacted by a Falling Weight |
ASTM D 7884 : 2020 | Standard Test Method for Determination of 4-Carboxybenzaldehyde and <emph type="bdit" >p</emph>-Toluic Acid in Purified Terephthalic Acid by Reverse Phase High Performance Liquid Chromatography |
ASTM D 8247 : 2019 | Standard Test Method for Determination of Total Fluorine and Total Chlorine in Coal by Oxidative Pyrohydrolytic Combustion Followed by Ion Chromatography Detection |
ASTM D 4968 : 2019 : REV A | Standard Practice for Annual Review of Test Methods and Specifications for Plastics |
ASTM D 4874 : 1995 : R2014 | Standard Test Method for Leaching Solid Material in a Column Apparatus (Withdrawn 2021) |
ASTM E 1967 : 2019 | Standard Test Method for the Automated Determination of Refractive Index of Glass Samples Using the Oil Immersion Method and a Phase Contrast Microscope |
ASTM D 1621 : 2016 | Standard Test Method for Compressive Properties of Rigid Cellular Plastics |
ASTM D 635 : 2018 | Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position |
ASTM G 200 : 2020 | Standard Test Method for Measurement of Oxidation-Reduction Potential (ORP) of Soil |
ASTM D 3801 : 2020 : REV A | Standard Test Method for Measuring the Comparative Burning Characteristics of Solid Plastics in a Vertical Position |
ASTM C 832 : 2000 : R2021 | Standard Test Method for Measuring Thermal Expansion and Creep of Refractories Under Load |
ASTM F 756 : 2017 | Standard Practice for Assessment of Hemolytic Properties of Materials |
ASTM E 2283 : 2008 : R2019 | Standard Practice for Extreme Value Analysis of Nonmetallic Inclusions in Steel and Other Microstructural Features |
ASTM G 176 : 2003 : R2017 | Standard Test Method for Ranking Resistance of Plastics to Sliding Wear Using Block-on-Ring Wear Test—Cumulative Wear Method |
ASTM D 5556 : 2019 | Standard Test Method for Determination of the Moisture and Other Volatile Matter Contained in Fats and Oils Used in Fatliquors and Softening Compounds |
ASTM E 1601 : 2019 | Standard Practice for Conducting an Interlaboratory Study to Evaluate the Performance of an Analytical Method |
ASTM F 1868 : 2017 | Standard Test Method for Thermal and Evaporative Resistance of Clothing Materials Using a Sweating Hot Plate |
ASTM D 3014 : 2019 : REV A | Standard Test Method for Flame Height, Time of Burning, and Loss of Mass of Rigid Thermoset Cellular Plastics in a Vertical Position |
ASTM D 1708 : 2018 | Standard Test Method for Tensile Properties of Plastics by Use of Microtensile Specimens |
ASTM C 1419 : 2014 : R2020 | Standard Test Method for Sonic Velocity in Refractory Materials at Room Temperature and Its Use in Obtaining an Approximate Young's Modulus |
ASTM B 528 : 2016 : R2020 : EDT 1 | Standard Test Method for Transverse Rupture Strength of Powder Metallurgy (PM) Specimens |
ASTM D 4180 : 2013 : R2018 | Standard Test Method for Vibratory Packing Density of Formed Catalyst Particles and Catalyst Carriers |
ASTM D 8132/D8132M : 2017 | Standard Test Method for Determination of Prepreg Impregnation by Permeability Measurement |
ASTM D 6108 : 2019 | Standard Test Method for Compressive Properties of Plastic Lumber and Shapes |
ASTM D 785 : 2008 : R2015 | Standard Test Method for Rockwell Hardness of Plastics and Electrical Insulating Materials |
ASTM D 2116 : 2016 | Standard Specification for FEP Resin Molding and Extrusion Materials |
ASTM A 773/A773M : 2021 | Standard Test Method for Direct Current Magnetic Properties of Low Coercivity Magnetic Materials Using Hysteresigraphs |
ASTM D 4318 : 2017 : EDT 1 | Standard Test Methods for Liquid Limit, Plastic Limit, and Plasticity Index of Soils |
ASTM D 7860 : 2014 | Standard Test Methods for Measurement of Torque Retention for Child Resistant and Non-Child Resistant Packages with Continuous Thread Closures Using Automated Torque Testing Equipment |
ASTM D 7515 : 2019 | Standard Test Method for Purity of 1,3-Propanediol (Gas Chromatographic Method) |
ASTM E 2490 : 2009 : R2021 | Standard Guide for Measurement of Particle Size Distribution of Nanomaterials in Suspension by Photon Correlation Spectroscopy (PCS) |
ASTM D 8005 : 2018 | Standard Test Method for Color of Clear Liquids (Platinum-Cobalt Scale) |
ASTM D 790 : 2017 | Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials |
ASTM D 7883 : 2020 | Standard Test Method for Determination of 4-Carboxybenzaldehyde and <emph type="bdit" >p</emph>-Toluic Acid in Purified Terephthalic Acid by Weak Anion Exchange High Performance Liquid Chromatography |
ASTM D 6300 : 2020 : REV B | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 5961/D5961M : 2017 | Standard Test Method for Bearing Response of Polymer Matrix Composite Laminates |
ASTM D 5349 : 2019 | Standard Test Method for Determination of the Moisture and Volatile Content of Sulfonated, Sulfated Oils and Fatliquors by Oven Method |
ASTM D 8214 : 2018 | Standard Test Method for Forms of Sulfur in Coal by Inductively Coupled Plasma Atomic Emission Spectrometry |
ASTM E 3063 : 2017 | Test Method for Antimony Content Using Neutron Activation Analysis (NAA) |
ASTM D 7896 : 2019 | Standard Test Method for Thermal Conductivity, Thermal Diffusivity, and Volumetric Heat Capacity of Engine Coolants and Related Fluids by Transient Hot Wire Liquid Thermal Conductivity Method |
ASTM D 5742 : 2016 | Standard Test Method for Determination of Butane Activity of Activated Carbon |
ASTM D 4751 : 2020 : REV B | Standard Test Methods for Determining Apparent Opening Size of a Geotextile |
ASTM D 545 : 2019 | Standard Test Methods for Preformed Expansion Joint Fillers for Concrete Construction (Nonextruding and Resilient Types) |
ASTM D 7415 : 2018 | Standard Test Method for Condition Monitoring of Sulfate By-Products in In-Service Petroleum and Hydrocarbon Based Lubricants by Trend Analysis Using Fourier Transform Infrared (FT-IR) Spectrometry |
ASTM D 3769 : 2020 | Standard Test Method for Microcellular Urethanes—High-Temperature Sag |
ASTM F 2638 : 2018 | Standard Test Method for Using Aerosol Filtration for Measuring the Performance of Porous Packaging Materials as a Surrogate Microbial Barrier |
ASTM C 1497 : 2016 | Standard Specification for Cellulosic Fiber Stabilized Thermal Insulation |
ASTM D 2067 : 1997 : R2020 | Standard Test Method for Coarse Particles in Printing Ink Dispersions |
ASTM E 2591 : 2007 : R2013 | Standard Guide for Conducting Whole Sediment Toxicity Tests with Amphibians |
ASTM D 7133 : 2016 | Standard Test Method for Polyurethane Raw Materials: Instrumental Measurement of Tristimulus CIELAB Color and Yellowness Index of Liquids |
ASTM F 1326 : 2002 : R2016 | Standard Test Method for Measuring Maximum Dry Volume of Utility Vacuum Cleaners |
ASTM B 117 : 2019 | Standard Practice for Operating Salt Spray (Fog) Apparatus |
ASTM E 430 : 2019 | Standard Test Methods for Measurement of Gloss of High-Gloss Surfaces by Abridged Goniophotometry |
ASTM D 6258 : 2017 | Standard Test Method for Determination of Solvent Red 164 Dye Concentration in Diesel Fuels |
ASTM F 1710 : 2008 : R2016 | Standard Test Method for Trace Metallic Impurities in Electronic Grade Titanium by High Mass-Resolution Glow Discharge Mass Spectrometer (Withdrawn 2023) |
ASTM D 7818 : 2012 : R2016 | Standard Test Method for Enumeration of Proteolytic Bacteria in Fresh (Uncured) Hides and Skins |
ASTM E 2783 : 2011 : R2016 | Standard Test Method for Assessment of Antimicrobial Activity for Water Miscible Compounds Using a Time-Kill Procedure |
ASTM F 2980 : 2013 : R2017 | Standard Test Method for Analysis of Heavy Metals in Glass by Field Portable X-Ray Fluorescence (XRF) |
ASTM D 4797 : 2017 | Standard Test Methods for Gravimetric Analysis of White and Yellow Thermoplastic Pavement Marking |
ASTM D 2565 : 2016 | Standard Practice for Xenon-Arc Exposure of Plastics Intended for Outdoor Applications |
ASTM F 1884 : 2004 : R2018 | Standard Test Methods for Determining Residual Solvents in Packaging Materials |
ASTM D 8207 : 2018 | Standard Test Method for Determination of Metals in Purified Terephthalic Acid (PAT) by Atomic Absorption (AA) Spectrometry (Withdrawn 2023) |
ASTM F 1304 : 2018 | Standard Test Method for Deflection of Resilient Floor Tile |
ASTM D 5083 : 2017 | Standard Test Method for Tensile Properties of Reinforced Thermosetting Plastics Using Straight-Sided Specimens |
ASTM D 6113 : 2016 | Standard Test Method for Using a Cone Calorimeter to Determine Fire-Test-Response Characteristics of Insulating Materials Contained in Electrical or Optical Fiber Cables |
ASTM D 7520 : 2016 | Standard Test Method for Determining the Opacity of a Plume in the Outdoor Ambient Atmosphere |
ASTM F 2845 : 2014 | Standard Test Method for Measuring the Dynamic Stiffness (DS) and Cylindrical Coefficient of Restitution (CCOR) of Baseballs and Softballs |
ASTM D 7000 : 2019 : REV A | Standard Test Method for Sweep Test of Emulsified Asphalt Surface Treatment Samples |
ASTM D 7559/D7559M : 2009 : R2020 | Standard Test Method for Determining Pressure Decay of Inflatable Restraint Cushions |
ASTM D 5885/D5885M : 2020 | Standard Test Method for Oxidative Induction Time of Polyolefin Geosynthetics by High-Pressure Differential Scanning Calorimetry |
ASTM D 7280 : 2020 | Standard Test Method for Quinoline-Insoluble (QI) Content of Tar and Pitch by Stainless Steel Crucible Filtration |
ASTM D 3591 : 2017 | Standard Test Method for Determining Logarithmic Viscosity Number of Poly(Vinyl Chloride) (PVC) in Formulated Compounds |
ASTM F 2617 : 2015 | Standard Test Method for Identification and Quantification of Chromium, Bromine, Cadmium, Mercury, and Lead in Polymeric Material Using Energy Dispersive X-ray Spectrometry |
ASTM C 1335 : 2012 : R2017 | Standard Test Method for Measuring Non-Fibrous Content of Man-Made Rock and Slag Mineral Fiber Insulation |
ASTM E 1970 : 2016 | Standard Practice for Statistical Treatment of Thermoanalytical Data |
ASTM E 1655 : 2017 | Standard Practices for Infrared Multivariate Quantitative Analysis |
ASTM F 2338 : 2009 : R2020 | Standard Test Method for Nondestructive Detection of Leaks in Packages by Vacuum Decay Method |
ASTM D 1631 : 2010 : R2018 : EDT 1 | Standard Test Method for Water in Phenol and Related Materials by the Iodine Reagent Method |
ASTM D 852 : 2020 | Standard Test Method for Solidification Point of Benzene |
ASTM E 643 : 2015 | Standard Test Method for Ball Punch Deformation of Metallic Sheet Material |
ASTM C 531 : 2018 | Standard Test Method for Linear Shrinkage and Coefficient of Thermal Expansion of Chemical-Resistant Mortars, Grouts, Monolithic Surfacings, and Polymer Concretes |
ASTM D 542 : 2014 | Standard Test Method for Index of Refraction of Transparent Organic Plastics |
ASTM E 2653 : 2015 | Standard Practice for Conducting an Interlaboratory Study to Determine Precision Estimates for a Fire Test Method with Fewer Than Six Participating Laboratories |
ASTM D 6143 : 2018 | Standard Test Method for Iron Content of Bisphenol A (4,4<emph type="bdit">′</emph > - Isopropylidenediphenol) |
ASTM D 1994 : 2007 : R2015 | Standard Test Method for Determination of Acid Numbers of Hot-Melt Adhesives (Withdrawn 2021) |
ASTM D 7028 : 2007 : R2015 | Standard Test Method for Glass Transition Temperature (DMA Tg) of Polymer Matrix Composites by Dynamic Mechanical Analysis (DMA) |
ASTM E 2694 : 2016 | Standard Test Method for Measurement of Adenosine Triphosphate in Water-Miscible Metalworking Fluids |
ASTM D 6266 : 2000 : REV A : R2017 | Standard Test Method for Determining the Amount of Volatile Organic Compound (VOC) Released From Waterborne Automotive Coatings and Available for Removal in a VOC Control Device (Abatement) |
ASTM E 517 : 2019 | Standard Test Method for Plastic Strain Ratio <emph type="bdit">r</emph> for Sheet Metal |
ASTM D 7313 : 2020 | Standard Test Method for Determining Fracture Energy of Asphalt Mixtures Using the Disk-Shaped Compact Tension Geometry |
ASTM C 110 : 2020 | Standard Test Methods for Physical Testing of Quicklime, Hydrated Lime, and Limestone |
ASTM F 355 : 2016 : EDT 1 | Standard Test Method for Impact Attenuation of Playing Surface Systems, Other Protective Sport Systems, and Materials Used for Athletics, Recreation and Play |
ASTM D 3575 : 2020 | Standard Test Methods for Flexible Cellular Materials Made from Olefin Polymers |
ASTM E 2008 : 2017 | Standard Test Methods for Volatility Rate by Thermogravimetry |
ASTM D 5235 : 2018 | Standard Test Method for Microscopic Measurement of Dry Film Thickness of Coatings on Wood Products |
ASTM B 527 : 2020 | Standard Test Method for Tap Density of Metal Powders and Compounds |
ASTM E 1582 : 2017 | Standard Test Method for Temperature Calibration of Thermogravimetric Analyzers |
ASTM D 7348 : 2013 | Standard Test Methods for Loss on Ignition (LOI) of Solid Combustion Residues |
ASTM D 4562 : 2001 : R2019 | Standard Test Method for Shear Strength of Adhesives Using Pin-and-Collar Specimen |
ASTM F 1317 : 1998 : R2019 | Standard Test Method for Calibration of Microwave Ovens (Withdrawn 2024) |
ASTM D 4497 : 2010 : R2018 | Standard Test Method for Determining the Open Time of Hot Melt Adhesives (Manual Method) (Withdrawn 2021) |
ASTM D 5827 : 2009 : R2015 | Standard Test Method for Analysis of Engine Coolant for Chloride and Other Anions by Ion Chromatography |
ASTM D 1044 : 2019 | Standard Test Method for Resistance of Transparent Plastics to Surface Abrasion by the Taber Abraser |
ASTM B 703 : 2017 | Standard Test Method for Apparent Density of Metal Powders and Related Compounds Using the Arnold Meter |
ASTM E 811 : 2009 : R2020 : EDT 1 | Standard Practice for Measuring Colorimetric Characteristics of Retroreflectors Under Nighttime Conditions |
ASTM G 155 : 2013 | Standard Practice for Operating Xenon Arc Light Apparatus for Exposure of Non-Metallic Materials |
ASTM D 3389 : 2016 | Standard Test Method for Coated Fabrics Abrasion Resistance (Rotary Platform Abrader) |
ASTM F 3078 : 2015 | Standard Test Method for Identification and Quantification of Lead in Paint and Similar Coating Materials using Energy Dispersive X-ray Fluorescence Spectrometry (EDXRF) |
ASTM D 3906 : 2019 | Standard Test Method for Determination of Relative X-ray Diffraction Intensities of Faujasite-Type Zeolite-Containing Materials |
ASTM D 4713 : 2012 : R2020 | Standard Test Methods for Nonvolatile Content of Heatset and Liquid Printing Ink Systems |
ASTM E 2448 : 2018 | Standard Test Method for Determining the Superplastic Properties of Metallic Sheet Materials |
ASTM D 1414 : 2015 | Standard Test Methods for Rubber O-Rings |
ASTM C 1663 : 2018 | Standard Test Method for Measuring Waste Glass or Glass Ceramic Durability by Vapor Hydration Test |
ASTM D 7905/D7905M : 2019 : EDT 1 | Standard Test Method for Determination of the Mode II Interlaminar Fracture Toughness of Unidirectional Fiber-Reinforced Polymer Matrix Composites |
ASTM D 2863 : 2019 | Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index) |
ASTM D 1518 : 2014 | Standard Test Method for Thermal Resistance of Batting Systems Using a Hot Plate (Withdrawn 2023) |
ASTM D 6007 : 2014 | Standard Test Method for Determining Formaldehyde Concentrations in Air from Wood Products Using a Small-Scale Chamber |
ASTM C 1708/C1708M : 2019 | Standard Test Methods for Self-leveling Mortars Containing Hydraulic Cements |
ASTM E 119 : 2020 | Standard Test Methods for Fire Tests of Building Construction and Materials |
ASTM D 3846 : 2008 : R2015 | Standard Test Method for In-Plane Shear Strength of Reinforced Plastics (Withdrawn 2024) |
ASTM D 792 : 2020 | Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement |
ASTM C 1326 : 2013 : R2018 | Standard Test Method for Knoop Indentation Hardness of Advanced Ceramics |
ASTM E 855 : 2008 : R2013 | Standard Test Methods for Bend Testing of Metallic Flat Materials for Spring Applications Involving Static Loading |
ASTM D 4272/D4272M : 2015 | Standard Test Method for Total Energy Impact of Plastic Films by Dart Drop |
ASTM D 5758 : 2001 : R2015 | Standard Test Method for Determination of Relative Crystallinity of Zeolite ZSM-5 by X-Ray Diffraction |
ASTM D 850 : 2021 | Standard Test Method for Distillation of Industrial Aromatic Hydrocarbons and Related Materials |
ASTM C 580 : 2018 | Standard Test Method for Flexural Strength and Modulus of Elasticity of Chemical-Resistant Mortars, Grouts, Monolithic Surfacings, and Polymer Concretes |
ASTM E 177 : 2020 | Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods |
ASTM F 1926/F1926M : 2014 | Standard Test Method for Dissolution Testing of Calcium Phosphate Granules, Fabricated Forms, and Coatings |
ASTM D 2843 : 2019 | Standard Test Method for Density of Smoke from the Burning or Decomposition of Plastics |
ASTM F 623 : 2019 | Standard Performance Specification for Foley Catheter |
ASTM E 1354 : 2017 | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
ASTM D 5132 : 2020 | Standard Test Method for Horizontal Burning Rate of Polymeric Materials Used in Occupant Compartments of Motor Vehicles |
ASTM C 1259 : 2015 | Standard Test Method for Dynamic Young’s Modulus, Shear Modulus, and Poisson’s Ratio for Advanced Ceramics by Impulse Excitation of Vibration |
ASTM E 3193 : 2020 | Standard Test Method for Measurement of Lead (Pb) in Dust by Wipe, Paint, and Soil by Flame Atomic Absorption Spectrophotometry (FAAS) |
ASTM G 143 : 2003 : R2018 | Standard Test Method for Measurement of Web/Roller Friction Characteristics |
ASTM D 5399 : 2009 : R2017 | Standard Test Method for Boiling Point Distribution of Hydrocarbon Solvents by Gas Chromatography |
ASTM D 4365 : 2019 | Standard Test Method for Determining Micropore Volume and Zeolite Area of a Catalyst |
ASTM D 1003 : 2013 | Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics |
ASTM F 2837 : 2011 : R2018 | Standard Test Method for Hot Compression Properties of Gasket Materials |
ASTM D 6226 : 2021 | Standard Test Method for Open Cell Content of Rigid Cellular Plastics |
ASTM F 3095 : 2017 : REV A | Standard Practice for Laser Technologies for Direct Measurement of Cross Sectional Shape of Pipeline and Conduit by Rotating Laser Diodes and CCTV Camera System |
ASTM D 696 : 2016 | Standard Test Method for Coefficient of Linear Thermal Expansion of Plastics Between −30°C and 30°C with a Vitreous Silica Dilatometer |
ASTM F 1887 : 2014 : R2019 : EDT 1 | Standard Test Method for Measuring the Coefficient of Restitution (COR) of Baseballs and Softballs |
ASTM D 6701 : 2021 | Standard Test Method for Determining Water Vapor Transmission Rates Through Nonwoven and Plastic Barriers |
ASTM D 732 : 2017 | Standard Test Method for Shear Strength of Plastics by Punch Tool |
ASTM F 1819 : 2019 | Standard Test Method for Resistance of Materials Used in Protective Clothing to Penetration by Synthetic Blood Using a Mechanical Pressure Technique |
ASTM D 8078 : 2018 : EDT 1 | Standard Test Method for Ash Content of Asphalt and Emulsified Asphalt Residues |
ASTM D 5492 : 2017 | Standard Test Method for Determination of Xylene Solubles in Propylene Plastics |
ASTM F 2544 : 2011 : R2018 | Standard Test Method for Determining A-Weighted Sound Power Level of Central Vacuum Power Units |
ASTM D 7716 : 2011 : REV A : R2020 | Standard Test Method for Determination of Residual Methanol in Glycerin by Gas Chromatography |
ASTM E 2489 : 2016 | Standard Practice for Statistical Analysis of One-Sample and Two-Sample Interlaboratory Proficiency Testing Programs |
ASTM D 5965 : 2019 | Standard Test Methods for Density of Coating Powders |
ASTM F 2913 : 2019 | Standard Test Method for Measuring the Coefficient of Friction for Evaluation of Slip Performance of Footwear and Test Surfaces/Flooring Using a Whole Shoe Tester |
ASTM E 456 : 2013 : REV A : R2017 : EDT 4 | Standard Terminology Relating to Quality and Statistics |
ASTM D 4781 : 2003 : R2018 : EDT 1 | Standard Test Method for Mechanically Tapped Packing Density of Fine Catalyst Particles and Catalyst Carrier Particles |
ASTM D 4085 : 1993 : R2013 | Standard Test Method for Metals in Cellulose by Atomic Absorption Spectrophotometry |
ASTM D 7551 : 2010 : R2015 | Standard Test Method for Determination of Total Volatile Sulfur in Gaseous Hydrocarbons and Liquefied Petroleum Gases and Natural Gas by Ultraviolet Fluorescence (Withdrawn 2024) |
ASTM E 1805 : 2013 | Standard Test Method for Determination of Gold in Copper Concentrates by Fire Assay Gravimetry |
ASTM D 7291/D7291M : 2015 | Standard Test Method for Through-Thickness “Flatwise” Tensile Strength and Elastic Modulus of a Fiber-Reinforced Polymer Matrix Composite Material |
ASTM C 225 : 1985 : R2014 | Standard Test Methods for Resistance of Glass Containers to Chemical Attack |
ASTM D 1746 : 2015 | Standard Test Method for Transparency of Plastic Sheeting |
ASTM C 876 : 2015 | Standard Test Method for Corrosion Potentials of Uncoated Reinforcing Steel in Concrete |
ASTM E 1623 : 2016 | Standard Test Method for Determination of Fire and Thermal Parameters of Materials, Products, and Systems Using an Intermediate Scale Calorimeter (ICAL) |
ASTM E 3098 : 2017 | Standard Test Method for Mechanical Uniaxial Pre-strain and Thermal Free Recovery of Shape Memory Alloys |
ASTM D 4512 : 2003 : R2018 : EDT 1 | Standard Test Method for Vibrated Apparent Packing Density of Fine Catalyst and Catalyst Carrier Particles and Powder |
ASTM F 1165 : 2020 | Standard Test Method for Measuring Angular Displacement of Multiple Images in Transparent Parts |
ASTM E 2335 : 2017 | Standard Guide for Laboratory Monitors |
ASTM F 2299/F2299M : 2003 : R2017 | Standard Test Method for Determining the Initial Efficiency of Materials Used in Medical Face Masks to Penetration by Particulates Using Latex Spheres |
ASTM D 1425/D1425M : 2014 : R2020 | Standard Test Method for Evenness of Textile Strands Using Capacitance Testing Equipment |
ASTM D 4493 : 2020 | Standard Test Method for Solidification Point of Bisphenol A<brk/>(4,4<emph type="ital" >′</emph>-Isopropylidenediphenol) |
ASTM D 6272 : 2017 : EDT 1 | Standard Test Method for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials by Four-Point Bending |
ASTM D 6900 : 2010 : R2020 | Standard Test Method for Wet Adhesion of Latex Paints to a Gloss Alkyd Enamel Substrate |
ASTM D 7057 : 2018 | Standard Test Method for Analysis of Isopropylbenzene (Cumene) by Gas Chromatography (External Standard) |
ASTM E 2864 : 2018 | Standard Test Method for Measurement of Airborne Metal Oxide Nanoparticle Surface Area Concentration in Inhalation Exposure Chambers using Krypton Gas Adsorption |
ASTM D 7127 : 2017 | Standard Test Method for Measurement of Surface Roughness of Abrasive Blast Cleaned Metal Surfaces Using a Portable Stylus Instrument (Withdrawn 2021) |
ASTM D 3985 : 2017 | Standard Test Method for Oxygen Gas Transmission Rate Through Plastic Film and Sheeting Using a Coulometric Sensor |
ASTM F 558 : 2021 | Standard Test Method for Measuring Air Performance Characteristics of Vacuum Cleaners |
ASTM C 1674 : 2016 | Standard Test Method for Flexural Strength of Advanced Ceramics with Engineered Porosity (Honeycomb Cellular Channels) at Ambient Temperatures |
ASTM D 5748 : 1995 : R2019 | Standard Test Method for Protrusion Puncture Resistance of Stretch Wrap Film |
ASTM D 7330 : 2015 | Standard Test Method for Assessment of Surface Appearance Change in Pile Floor Coverings Using Standard Reference Scales |
ASTM D 5135 : 2021 | Standard Test Method for Analysis of Styrene by Capillary Gas Chromatography |
ASTM D 7897 : 2018 | Standard Practice for Laboratory Soiling and Weathering of Roofing Materials to Simulate Effects of Natural Exposure on Solar Reflectance and Thermal Emittance |
ASTM D 4533/D4533M : 2015 | Standard Test Method for Trapezoid Tearing Strength of Geotextiles |
ASTM D 2066 : 2007 : R2020 | Standard Test Methods for Relative Tinting Strength of Paste-Type Printing Ink Dispersions |
ASTM D 8069 : 2017 : REV A | Standard Test Method for Determining Flexural Modulus of Full Section Pultruded Fiber Reinforced Polymer (FRP) Composite Members with Doubly Symmetric Cross Sections under Bending |
ASTM E 18 : 2020 | Standard Test Methods for Rockwell Hardness of Metallic Materials |
ASTM F 1306 : 2021 | Standard Test Method for Slow Rate Penetration Resistance of Flexible Barrier Films and Laminates |
ASTM D 1823 : 2016 | Standard Test Method for Apparent Viscosity of Plastisols and Organosols at High Shear Rates by Extrusion Viscometer |
ASTM D 6414 : 2014 | Standard Test Methods for Total Mercury in Coal and Coal Combustion Residues by Acid Extraction or Wet Oxidation/Cold Vapor Atomic Absorption |
ASTM D 6267/D6267M : 2013 : R2017 | Standard Test Method for Apparent Viscosity of Hydrocarbon Resins at Elevated Temperatures |
ASTM D 7964/D7964M : 2019 | Standard Test Method for Determining Activity of Fluid Catalytic Cracking (FCC) Catalysts in a Fluidized Bed |
ASTM E 28 : 2018 | Standard Test Methods for Softening Point of Resins Derived from Pine Chemicals and Hydrocarbons, by Ring-and-Ball Apparatus |
ASTM F 1514 : 2019 | Standard Test Method for Measuring Heat Stability of Resilient Flooring by Color Change |
ASTM F 2826 : 2014 : R2018 | Standard Test Method for Evaluating the Sustained Air Performance and Exhaust Emission Efficiencies of Central Vacuum Cleaning Units |
ASTM D 4274 : 2016 | Standard Test Methods for Testing Polyurethane Raw Materials: Determination of Hydroxyl Numbers of Polyols |
ASTM D 7202 : 2015 | Standard Test Method for Determination of Beryllium in the Workplace by Extraction and Optical Fluorescence Detection |
ASTM B 886 : 2019 | Standard Test Method for Determination of Magnetic Saturation (Ms) of Cemented Carbides |
ASTM G 142 : 1998 : R2016 | Standard Test Method for Determination of Susceptibility of Metals to Embrittlement in Hydrogen Containing Environments at High Pressure, High Temperature, or Both |
ASTM D 2582 : 2016 | Standard Test Method for Puncture-Propagation Tear Resistance of Plastic Film and Thin Sheeting |
ASTM D 7785 : 2021 | Standard Practice for Water in Lint Cotton by Oven Evaporation Combined with Volumetric Karl Fischer Titration |
ASTM D 3749 : 2019 | Standard Test Method for Residual Vinyl Chloride Monomer in Poly(Vinyl Chloride) Resins by Gas Chromatographic Headspace Technique |
ASTM D 5459 : 1995 : R2020 | Standard Test Method for Machine Direction Elastic Recovery and Permanent Deformation and Stress Retention of Stretch Wrap Film |
ASTM D 4226 : 2019 : EDT 1 | Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products |
ASTM C 579 : 2018 | Standard Test Methods for Compressive Strength of Chemical-Resistant Mortars, Grouts, Monolithic Surfacings, and Polymer Concretes |
ASTM D 5422 : 2017 | Standard Test Method for Measurement of Properties of Thermoplastic Materials by Screw-Extrusion Capillary Rheometer |
ASTM D 6241 : 2014 | Standard Test Method for Static Puncture Strength of Geotextiles and Geotextile-Related Products Using a 50-mm Probe |
ASTM G 122 : 2020 | Standard Test Method for Evaluating the Effectiveness of Cleaning Agents and Processes |
ASTM F 2136 : 2018 | Standard Test Method for Notched, Constant Ligament-Stress (NCLS) Test to Determine Slow-Crack-Growth Resistance of HDPE Resins or HDPE Corrugated Pipe |
ASTM E 1353 : 2016 | Standard Test Methods for Cigarette Ignition Resistance of Components of Upholstered Furniture |
ASTM C 1371 : 2015 | Standard Test Method for Determination of Emittance of Materials Near Room Temperature Using Portable Emissometers |
ASTM D 1002 : 2010 : R2019 | Standard Test Method for Apparent Shear Strength of Single-Lap-Joint Adhesively Bonded Metal Specimens by Tension Loading (Metal-to-Metal) |
ASTM F 2731 : 2018 | Standard Test Method for Measuring the Transmitted and Stored Energy of Firefighter Protective Clothing Systems |
ASTM D 6796 : 2016 | Standard Practice for Production of Coal, Coke and Coal Combustion Samples for Interlaboratory Studies |
ASTM E 2551 : 2020 | Standard Test Methods for Humidity Calibration (or Conformation) of Humidity Generators for Use with Thermogravimetric Analyzers |
ASTM B 939 : 2015 | Standard Test Method for Radial Crushing Strength, <emph type="bdit">K</emph>, of Powder Metallurgy (PM) Bearings and Structural Materials |
ASTM F 609 : 2005 : R2013 | Standard Test Method for Using a Horizontal Pull Slipmeter (HPS) (Withdrawn 2022) |
ASTM D 8019 : 2015 | Standard Test Methods for Determining the Full Section Flexural Modulus and Bending Strength of Fiber Reinforced Polymer Crossarms Assembled with Center Mount Brackets |
ASTM C 1549 : 2016 | Standard Test Method for Determination of Solar Reflectance Near Ambient Temperature Using a Portable Solar Reflectometer |
ASTM F 3287 : 2017 : EDT 1 | Standard Test Method for Nondestructive Detection of Leaks in Packages by Mass Extraction Method |
ASTM E 535 : 2019 | Standard Practice for Preparation of Fire-Test-Response Standards |
ASTM D 5357 : 2019 | Standard Test Method for Determination of Relative Crystallinity of Zeolite Sodium A by X-ray Diffraction |
ASTM E 646 : 2016 | Standard Test Method for Tensile Strain-Hardening Exponents (<emph type="bdit">n</emph > -Values) of Metallic Sheet Materials |
ASTM C 1891 : 2020 | Standard Test Method for Fineness of Hydraulic Cement by Air Jet Sieving at 45-µm (No. 325) |
ASTM D 8040 : 2018 | Standard Test Method for Corrosion Test for Heat Transfer Fluids in Glassware |
ASTM D 1921 : 2018 | Standard Test Methods for Particle Size (Sieve Analysis) of Plastic Materials |
ASTM E 194 : 2020 | Standard Test Method for Acid-Insoluble Content of Copper and Iron Powders |
ASTM E 1367 : 2003 : R2014 | Standard Test Method for Measuring the Toxicity of Sediment-Associated Contaminants with Estuarine and Marine Invertebrates |
ASTM D 4273 : 2018 | Standard Test Method for Polyurethane Raw Materials: Determination of Primary Hydroxyl Content of Polyether Polyols |
ASTM F 2977 : 2020 | Standard Test Method for Small Punch Testing of Polymeric Biomaterials Used in Surgical Implants |
ASTM F 2894 : 2019 | Standard Test Method for Evaluation of Materials, Protective Clothing, and Equipment for Heat Resistance Using a Hot Air Circulating Oven |
ASTM D 4417 : 2021 | Standard Test Methods for Field Measurement of Surface Profile of Blast Cleaned Steel |
ASTM F 387 : 2017 | Standard Test Method for Measuring Thickness of Resilient Floor Covering With Foam Layer |
ASTM C 413 : 2018 | Standard Test Method for Absorption of Chemical-Resistant Mortars, Grouts, Monolithic Surfacings, and Polymer Concretes |
ASTM D 5458 : 1995 : R2020 | Standard Test Method for Peel Cling of Stretch Wrap Film |
ASTM F 137 : 2008 : R2018 | Standard Test Method for Flexibility of Resilient Flooring Materials with Cylindrical Mandrel Apparatus |
ASTM D 7624 : 2018 | Standard Test Method for Condition Monitoring of Nitration in In-Service Petroleum and Hydrocarbon-Based Lubricants by Trend Analysis Using Fourier Transform Infrared (FT-IR) Spectrometry |
ASTM B 873 : 2017 | Standard Test Method for Measuring Volume of Apparent Density Cup Used in Test Methods B212, B329, and B417 |
ASTM D 7271 : 2006 : R2020 | Standard Test Method for Viscoelastic Properties of Paste Ink Vehicle Using an Oscillatory Rheometer |
ASTM F 904 : 2016 | Standard Test Method for Comparison of Bond Strength or Ply Adhesion of Similar Laminates Made from Flexible Materials |
ASTM E 1194 : 2017 | Standard Test Method for Vapor Pressure |
ASTM D 5306 : 1992 : R2018 | Standard Test Method for Linear Flame Propagation Rate of Lubricating Oils and Hydraulic Fluids |
ASTM D 3321 : 2019 | Standard Test Method for Use of the Refractometer for Field Test Determination of the Freezing Point of Aqueous Engine Coolants |
ASTM F 1515 : 2015 | Standard Test Method for Measuring Light Stability of Resilient Flooring by Color Change |
ASTM E 398 : 2020 | Standard Test Method for Water Vapor Transmission Rate of Sheet Materials Using Dynamic Relative Humidity Measurement |
ASTM D 2868 : 2017 | Standard Test Method for Nitrogen Content (Kjeldahl) and Hide Substance Content of Leather, Wet Blue and Wet White |
ASTM D 6130 : 2011 : R2018 | Standard Test Method for Determination of Silicon and Other Elements in Engine Coolant by Inductively Coupled Plasma-Atomic Emission Spectroscopy |
ASTM F 820 : 2021 | Standard Test Method for Measuring Air Performance Characteristics of Central Vacuum Cleaning Systems |
ASTM D 4061 : 2013 : R2018 | Standard Test Method for Retroreflectance of Horizontal Coatings |
ASTM D 3895 : 2019 | Standard Test Method for Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry |
ASTM D 6693/D6693M : 2020 | Standard Test Method for Determining Tensile Properties of Nonreinforced Polyethylene and Nonreinforced Flexible Polypropylene Geomembranes |
ASTM E 2994 : 2016 | Standard Test Method for Analysis of Titanium and Titanium Alloys by Spark Atomic Emission Spectrometry and Glow Discharge Atomic Emission Spectrometry (Performance-Based Method) |
ASTM D 4499 : 2007 : R2015 | Standard Test Method for Heat Stability of Hot-Melt Adhesives (Withdrawn 2021) |
ASTM E 1860 : 2013 : R2018 | Standard Test Method for Elapsed Time Calibration of Thermal Analyzers |
ASTM C 1108 : 2017 | Standard Test Method for Plutonium by Controlled-Potential Coulometry |
ASTM D 8020 : 2015 : R2020 | Standard Test Method for Freeze-Thaw Viscosity Stability of Water-Based Inks and Ink Vehicles |
ASTM C 1025 : 2015 : R2020 | Standard Test Method for Modulus of Rupture in Bending of Electrode Graphite |
ASTM D 4321 : 2015 | Standard Test Method for Package Yield of Plastic Film (Withdrawn 2024) |
ASTM D 4476/D4476M : 2014 | Standard Test Method for Flexural Properties of Fiber Reinforced Pultruded Plastic Rods (Withdrawn 2022) |
ASTM D 7686 : 2019 | Standard Test Method for Field-Based Condition Monitoring of Soot in In-Service Lubricants Using a Fixed-Filter Infrared (IR) Instrument |
ASTM D 4791 : 2019 | Standard Test Method for Flat Particles, Elongated Particles, or Flat and Elongated Particles in Coarse Aggregate |
ASTM D 6493 : 2011 : R2015 | Standard Test Methods for Softening Point of Hydrocarbon Resins and Rosin Based Resins by Automated Ring-and-Ball Apparatus |
ASTM D 4440 : 2015 | Standard Test Method for Plastics: Dynamic Mechanical Properties Melt Rheology |
ASTM D 7911 : 2019 | Standard Guide for Using Reference Material to Characterize Measurement Bias Associated with Volatile Organic Compound Emission Chamber Test |
ASTM D 1238 : 2020 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
ASTM D 7427 : 2016 | Standard Test Method for Immunological Measurement of Four Principal Allergenic Proteins (Hev b 1, 3, 5 and 6.02) in Hevea Natural Rubber and Its Products Derived from Latex |
ASTM F 2391 : 2005 : R2016 | Standard Test Method for Measuring Package and Seal Integrity Using Helium as the Tracer Gas |
ASTM D 6090 : 2017 | Standard Test Method for Softening Point Resins (Mettler Cup and Ball Method) |
ASTM D 3760 : 2018 | Standard Test Method for Analysis of Isopropylbenzene (Cumene) by Gas Chromatography (Withdrawn 2022) |
ASTM D 4804 : 2020 | Standard Test Method for Determining the Flammability Characteristics of Nonrigid Solid Plastics |
ASTM D 4253 : 2016 : EDT 1 | Standard Test Methods for Maximum Index Density and Unit Weight of Soils Using a Vibratory Table |
ASTM D 3942 : 2019 | Standard Test Method for Determination of the Unit Cell Dimension of a Faujasite-Type Zeolite |
ASTM F 2157 : 2009 : R2018 | Standard Specification for Synthetic Surfaced Running Tracks |
ASTM C 794 : 2018 | Standard Test Method for Adhesion-in-Peel of Elastomeric Joint Sealants |
ASTM C 1702 : 2017 | Standard Test Method for Measurement of Heat of Hydration of Hydraulic Cementitious Materials Using Isothermal Conduction Calorimetry |
ASTM D 6913/D6913M : 2017 | Standard Test Methods for Particle-Size Distribution (Gradation) of Soils Using Sieve Analysis |
ASTM F 3263 : 2017 | Standard Guide for Packaging Test Method Validation |
ASTM D 7998 : 2019 | Standard Test Method for Measuring the Effect of Temperature on the Cohesive Strength Development of Adhesives using Lap Shear Bonds under Tensile Loading |
ASTM F 2476 : 2020 | Standard Test Method for the Determination of Carbon Dioxide Gas Transmission Rate (CO<inf >2</inf>TR) Through Barrier Materials Using an Infrared Detector |
ASTM D 7591 : 2012 : R2017 | Standard Test Method for Determination of Free and Total Glycerin in Biodiesel Blends by Anion Exchange Chromatography |
ASTM F 3004 : 2013 : R2020 | Standard Test Method for Evaluation of Seal Quality and Integrity Using Airborne Ultrasound |
ASTM D 4301 : 2005(R2019) | Standard Test Method for Total Chlorine in Epoxy Resins and Compounds |
ASTM D 5887/D5887M : 2020 | Standard Test Method for Measurement of Index Flux Through Saturated Geosynthetic Clay Liner Specimens Using a Flexible Wall Permeameter |
ASTM F 1717 : 2018 | Standard Test Methods for Spinal Implant Constructs in a Vertebrectomy Model |
ASTM D 6721 : 2001 : R2015 | Standard Test Method for Determination of Chlorine in Coal by Oxidative Hydrolysis Microcoulometry |
ASTM D 1709 : 2016 : REV A : EDT 1 | Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method |
ASTM D 3364 : 1999 : R2019 | Standard Test Method for Flow Rates for Poly(Vinyl Chloride) with Molecular Structural Implications |
ASTM D 5795 : 2016 | Standard Test Method for Determination of Liquid Water Absorption of Coated Wood and Wood Based Products Via “Cobb Ring” Apparatus |
ASTM D 6979 : 2018 | Standard Test Method for Polyurethane Raw Materials: Determination of Basicity in Polyols, Expressed as Percent Nitrogen |
ASTM D 7063/D7063M : 2018 | Standard Test Method for Effective Porosity and Effective Air Voids of Compacted Asphalt Mixture Samples |
ASTM C 1171 : 2016 | Standard Test Method for Quantitatively Measuring the Effect of Thermal Shock and Thermal Cycling on Refractories |
ASTM D 2583 : 2013 : REV A | Standard Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor (Withdrawn 2022) |
ASTM D 1214 : 2010 : R2020 | Standard Test Method for Sieve Analysis of Glass Spheres |
ASTM D 1693 : 2015 : EDT 1 | Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics |
ASTM D 6195 : 2003 : R2019 | Standard Test Methods for Loop Tack |
ASTM D 4812 : 2019 | Standard Test Method for Unnotched Cantilever Beam Impact Resistance of Plastics |
ASTM D 6566 : 2018 | Standard Test Method for Measuring Mass Per Unit Area of Turf Reinforcement Mats |
ASTM D 1316 : 2020 | Standard Test Method for Fineness of Grind of Printing Inks By the NPIRI Grindometer |
ASTM F 608 : 2018 | Standard Test Method for Evaluation of Carpet Embedded Dirt Removal Effectiveness of Household/Commercial Vacuum Cleaners |
ASTM D 3763 : 2018 | Standard Test Method for High Speed Puncture Properties of Plastics Using Load and Displacement Sensors |
ASTM D 8289 : 2020 | Standard Test Method for Tensile Strength Estimate by Disc Compression of Manufactured Graphite |
ASTM D 2121 : 2016 | Standard Test Methods for Polymer Content of Styrene Monomer |
ASTM F 2203 : 2013 : R2018 | Standard Test Method for Linear Measurement Using Precision Steel Rule |
ASTM D 7786 : 2013 : R2019 | Standard Test Method for Determining Enamel Holdout |
ASTM D 1494 : 2017 | Standard Test Method for Diffuse Light Transmission Factor of Reinforced Plastics Panels |
ASTM E 2649 : 2020 | Standard Test Method for Determining Argon Concentration in Sealed Insulating Glass Units Using Spark Emission Spectroscopy |
ASTM D 7635/D7635M : 2018 | Standard Test Method for Measurement of Thickness of Coatings Over Fabric Reinforcement |
ASTM D 4491/D4491M : 2020 : EDT 1 | Standard Test Methods for Water Permeability of Geotextiles by Permittivity |
ASTM G 220 : 2020 | Standard Practice for Replacing Saturated Calomel Reference Electrode (SCE) for Measuring Electrode Potentials |
ASTM D 1603 : 2020 | Standard Test Method for Carbon Black Content in Olefin Plastics |
ASTM C 1291 : 2018 | Standard Test Method for Elevated Temperature Tensile Creep Strain, Creep Strain Rate, and Creep Time to Failure for Monolithic Advanced Ceramics |
ASTM D 1335 : 2021 | Standard Test Method for Tuft Bind of Pile Yarn Floor Coverings |
ASTM D 6289 : 2013 : R2019 | Standard Test Method for Measuring Shrinkage from Mold Dimensions of Molded Thermosetting Plastics |
ASTM B 330 : 2020 | Standard Test Methods for Estimating Average Particle Size of Metal Powders and Related Compounds Using Air Permeability |
ASTM D 1240 : 2014 : R2018 | Standard Test Methods for Rosin Acids Content of Pine Chemicals, Including Rosin, Tall Oil, and Related Products |
ASTM E 2177 : 2020 | Standard Test Method for Measuring the Coefficient of Retroreflected Luminance (R<inf >L</inf>) of Pavement Markings using the Bucket Method in a Condition of Wet Recovery |
ASTM D 7458 : 2014 | Standard Test Method for Determination of Beryllium in Soil, Rock, Sediment, and Fly Ash Using Ammonium Bifluoride Extraction and Fluorescence Detection |
ASTM E 2406 : 2016 | Standard Test Method for Evaluation of Laundry Sanitizers and Disinfectants for Use in High Efficiency Washing Operations |
ASTM D 8054/D8054M : 2016 | Standard Test Methods for Tensile Testing of Para-Aramid Flat Yarns |
ASTM D 4926 : 2020 | Standard Test Method for Gamma Alumina Content in Catalysts and Catalyst Carriers Containing Silica and Alumina by X-ray Powder Diffraction |
ASTM D 5448/D5448M : 2016 | Standard Test Method for Inplane Shear Properties of Hoop Wound Polymer Matrix Composite Cylinders |
ASTM F 2625 : 2010 : R2016 | Standard Test Method for Measurement of Enthalpy of Fusion, Percent Crystallinity, and Melting Point of Ultra-High-Molecular Weight Polyethylene by Means of Differential Scanning Calorimetry |
ASTM F 1940 : 2007 : REV A : R2019 | Standard Test Method for Process Control Verification to Prevent Hydrogen Embrittlement in Plated or Coated Fasteners |
ASTM D 3670 : 1991 : R2014 | Standard Guide for Determination of Precision and Bias of Methods of Committee D22 |
ASTM D 6738 : 2015 : R2019 | Standard Test Method for Precipitated Silica—Volatile Content |
ASTM B 887 : 2012 : R2019 | Standard Test Method for Determination of Coercivity (Hcs) of Cemented Carbides |
ASTM D 1922 : 2015 : R2020 | Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method |
ASTM E 2480 : 2012 : R2017 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method with Multi-Valued Measurands |
ASTM C 704/C704M : 2015 : EDT 1 | Standard Test Method for Abrasion Resistance of Refractory Materials at Room Temperature |
ASTM F 3300 : 2018 | Standard Test Method for Abrasion Resistance of Flexible Packaging Films Using a Reciprocating Weighted Stylus |
ASTM D 7514 : 2014 | Standard Test Method for Evaluating Ink Stainblocking of Architectural Paint Systems by Visual Assessment |
ASTM D 7940 : 2014 | Standard Practice for Analysis of Liquefied Natural Gas (LNG) by Fiber-Coupled Raman Spectroscopy |
ASTM D 6722 : 2019 | Standard Test Method for Total Mercury in Coal and Coal Combustion Residues by Direct Combustion Analysis |
ASTM E 948 : 2016 : R2020 | Standard Test Method for Electrical Performance of Photovoltaic Cells Using Reference Cells Under Simulated Sunlight |
ASTM D 1824 : 2016 | Standard Test Method for Apparent Viscosity of Plastisols and Organosols at Low Shear Rates |
ASTM D 4603 : 2018 | Standard Test Method for Determining Inherent Viscosity of Poly(Ethylene Terephthalate) (PET) by Glass Capillary Viscometer |
ASTM D 7370/D7370M : 2014 | Standard Test Method for Determination of Relative Density and Absorption of Fine, Coarse and Blended Aggregate Using Combined Vacuum Saturation and Rapid Submersion |
ASTM D 2065 : 2003 : R2017 | Standard Test Method for Determination of Edge Performance of Composite Wood Products Under Surfactant Accelerated Moisture Stress |
ASTM E 110 : 2014 | Standard Test Method for Rockwell and Brinell Hardness of Metallic Materials by Portable Hardness Testers |
ASTM D 6762 : 2018 | Standard Test Method for Determining the Hiding Power of Paint by Visual Evaluation of Spray Applied Coatings |
ASTM D 6499 : 2018 | Standard Test Method for Immunological Measurement of Antigenic Protein in Hevea Natural Rubber (HNR) and its Products |
ASTM D 1667 : 2017 | Standard Specification for Flexible Cellular Materials—Poly (Vinyl Chloride) Foam (Closed-Cell) |
ASTM D 5084 : 2016 : REV A | Standard Test Methods for Measurement of Hydraulic Conductivity of Saturated Porous Materials Using a Flexible Wall Permeameter |
ASTM F 2516 : 2018 | Standard Test Method for Tension Testing of Nickel-Titanium Superelastic Materials |
ASTM C 1067 : 2020 | Standard Practice for Conducting a Ruggedness Evaluation or Screening Program for Test Methods for Construction Materials |
ASTM D 5828 : 1997 : R2018 | Standard Test Method for Compatibility of Supplemental Coolant Additives (SCAs) and Engine Coolant Concentrates |
ASTM C 1427 : 2016 | Standard Specification for Extruded Preformed Flexible Cellular Polyolefin Thermal Insulation in Sheet and Tubular Form |
ASTM D 1499 : 2013 | Standard Practice for Filtered Open-Flame Carbon-Arc Exposures of Plastics |
ASTM D 6857/D6857M : 2018 | Standard Test Method for Maximum Specific Gravity and Density of Asphalt Mixtures Using Automatic Vacuum Sealing Method |
ASTM C 1501 : 2019 | Standard Test Method for Color Stability of Building Construction Sealants as Determined by Laboratory Accelerated Weathering Procedures |
ASTM C 651 : 2020 | Standard Test Method for Flexural Strength of Manufactured Carbon and Graphite Articles Using Four-Point Loading at Room Temperature |
ASTM E 3039 : 2020 | Standard Test Method for Determination of Crack-Tip-Opening Angle of Ferritic Steels Using DWTT-Type Specimens |
ASTM C 747 : 2016 | Standard Test Method for Moduli of Elasticity and Fundamental Frequencies of Carbon and Graphite Materials by Sonic Resonance |
ASTM D 7972 : 2014 : R2020 | Standard Test Method for Flexural Strength of Manufactured Carbon and Graphite Articles Using Three-Point Loading at Room Temperature |
ASTM E 2455 : 2006 : R2013 | Standard Guide for Conducting Laboratory Toxicity Tests with Freshwater Mussels (Withdrawn 2022) |
ASTM D 1998 : 2015 | Standard Specification for Polyethylene Upright Storage Tanks |
ASTM G 5 : 2014 : EDT 1 | Standard Reference Test Method for Making Potentiodynamic Anodic Polarization Measurements |
ASTM D 4222 : 2020 | Standard Test Method for Determination of Nitrogen Adsorption and Desorption Isotherms of Catalysts and Catalyst Carriers by Static Volumetric Measurements |
ASTM D 5757 : 2011 : R2017 | Standard Test Method for Determination of Attrition of FCC Catalysts by Air Jets |
ASTM E 1858 : 2008 : R2015 : EDT 1 | Standard Test Methods for Determining Oxidation Induction Time of Hydrocarbons by Differential Scanning Calorimetry |
ASTM C 24 : 2009 : R2018 | Standard Test Method for Pyrometric Cone Equivalent (PCE) of Fireclay and High-Alumina Refractory Materials |
ASTM E 1362 : 2015 : R2019 | Standard Test Methods for Calibration of Non-Concentrator Photovoltaic Non-Primary Reference Cells |
ASTM D 4541 : 2017 | Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers |
ASTM D 1203 : 2020 | Standard Test Methods for Volatile Loss From Plastics Using Activated Carbon Methods |
ASTM D 6817/D6817M : 2017 | Standard Specification for Rigid Cellular Polystyrene Geofoam |
ASTM E 2823 : 2017 | Standard Test Method for Analysis of Nickel Alloys by Inductively Coupled Plasma Mass Spectrometry (Performance-Based) |
ASTM D 7744/D7744M : 2020 | Standard Test Methods for Tensile Testing of High Performance Polyethylene Films |
ASTM D 5178 : 2016 | Standard Test Method for Mar Resistance of Organic Coatings |
ASTM D 7487 : 2018 | Standard Practice for Polyurethane Raw Materials: Polyurethane Foam Cup Test |
ASTM D 5508 : 2016 | Standard Test Method for Determination of Residual Acrylonitrile Monomer in Styrene-Acrylonitrile Copolymer Resins and Nitrile-Butadiene Rubber by Headspace-Capillary Gas Chromatography (HS-CGC) |
ASTM D 1622 : 2020 | Standard Test Method for Apparent Density of Rigid Cellular Plastics |
ASTM D 5227 : 2013 | Standard Test Method for Measurement of Hexane Extractable Content of Polyolefins |
ASTM D 8136 : 2017 | Standard Test Method for Determining Plastic Film Thickness and Thickness Variability Using a Non-Contact Capacitance Thickness Gauge |
ASTM E 1792 : 2020 | Standard Specification for Wipe Sampling Materials for Lead in Surface Dust |
ASTM D 1065 : 2018 | Standard Test Method for Unsaponifiable Matter in Pine Chemicals, Including Rosin, Tall Oil, and Related Products |
ASTM F 2797 : 2019 | Standard Test Method for Evaluating Edge Cleaning Effectiveness of Vacuum Cleaners |
ASTM E 384 : 2017 | Standard Test Method for Microindentation Hardness of Materials |
ASTM B 636/B636M : 2015 | Standard Test Method for Measurement of Internal Stress of Plated Metallic Coatings with the Spiral Contractometer |
ASTM D 6437 : 2005 : R2016 : EDT 1 | Standard Test Method for Polyurethane Raw Materials: Alkalinity in Low-Alkalinity Polyols (Determination of CPR Values of Polyols) |
ASTM C 1468 : 2019 : REV A | Standard Test Method for Transthickness Tensile Strength of Continuous Fiber-Reinforced Advanced Ceramics at Ambient Temperature |
ASTM D 7439 : 2014 | Standard Test Method for Determination of Elements in Airborne Particulate Matter by Inductively Coupled Plasma–Mass Spectrometry |
ASTM D 8115 : 2017 | Standard Test Method for Rubber Property—Abrasion Resistance (Multi-Directional Platform Abrader) |
ASTM D 6531 : 2000 : R2019 | Standard Test Method for Relative Tinting Strength of Aqueous Ink Systems by Instrumental Measurement |
ASTM C 1285 : 2014 | Standard Test Methods for Determining Chemical Durability of Nuclear, Hazardous, and Mixed Waste Glasses and Multiphase Glass Ceramics: The Product Consistency Test (PCT) |
ASTM F 1702 : 2010 : R2018 | Standard Test Method for Measuring Impact-Attenuation Characteristics of Natural Playing Surface Systems Using a Lightweight Portable Apparatus |
ASTM E 2655 : 2014 : R2020 | Standard Guide for Reporting Uncertainty of Test Results and Use of the Term Measurement Uncertainty in ASTM Test Methods |
ASTM D 7253 : 2016 | Standard Test Method for Polyurethane Raw Materials: Determination of Acidity as Acid Number for Polyether Polyols |
ASTM C 179 : 2014 : R2019 | Standard Test Method for Drying and Firing Linear Change of Refractory Plastic and Ramming Mix Specimens |
ASTM D 1726 : 2011 : R2019 | Standard Test Methods for Hydrolyzable Chloride Content of Liquid Epoxy Resins |
ASTM C 1869 : 2018 | Standard Test Method for Open-Hole Tensile Strength of Fiber-Reinforced Advanced Ceramic Composites |
ASTM E 1488 : 2012 : R2018 | Standard Guide for Statistical Procedures to Use in Developing and Applying Test Methods |
ASTM F 2055 : 2017 | Standard Test Method for Size and Squareness of Resilient Floor Tile by Dial Gage Method |
ASTM D 6175 : 2003 : R2019 | Standard Test Method for Radial Crush Strength of Extruded Catalyst and Catalyst Carrier Particles |
ASTM D 5450/D5450M : 2016 | Standard Test Method for Transverse Tensile Properties of Hoop Wound Polymer Matrix Composite Cylinders |
ASTM D 6357 : 2019 | Standard Test Methods for Determination of Trace Elements in Coal, Coke, and Combustion Residues from Coal Utilization Processes by Inductively Coupled Plasma Atomic Emission Spectrometry, Inductively Coupled Plasma Mass Spectrometry, and Graphite Furnace Atomic Absorption Spectrometry |
ASTM E 2269 : 2014 | Standard Test Method for Determining Argon Concentration in Sealed Insulating Glass Units using Gas Chromatography |
ASTM E 3160 : 2018 | Standard Test Method for Quantitative Evaluation of the Antibacterial Properties of Porous Antibacterial Treated Articles |
ASTM D 7304 : 2016 | Standard Test Method for Determination of Denatonium Ion in Engine Coolant by HPLC |
ASTM D 2134 : 2019 | Standard Test Method for Determining the Hardness of Organic Coatings with a Sward-Type Hardness Rocker |
ASTM C 749 : 2015 : R2020 | Standard Test Method for Tensile Stress-Strain of Carbon and Graphite |
ASTM F 1307 : 2020 | Standard Test Method for Oxygen Transmission Rate Through Dry Packages Using a Coulometric Sensor |
ASTM D 4674 : 2019 | Standard Practice for Accelerated Testing for Color Stability of Plastics Exposed to Indoor Office Environments |
ASTM C 1445 : 2013 : R2018 | Standard Test Method for Measuring Consistency of Castable Refractory Using a Flow Table |
ASTM C 67/C67M : 2020 | Standard Test Methods for Sampling and Testing Brick and Structural Clay Tile |
ASTM G 174 : 2004 : R2017 | Standard Test Method for Measuring Abrasion Resistance of Materials by Abrasive Loop Contact |
ASTM D 4383 : 2018 | Standard Specification for Plowable, Raised Retroreflective Pavement Markers |
ASTM D 6037 : 2018 | Standard Test Methods for Dry Abrasion Mar Resistance of High Gloss Coatings |
ASTM D 4020 : 2018 | Standard Specification for Ultra-High-Molecular-Weight Polyethylene Molding and Extrusion Materials |
ASTM D 6576 : 2020 | Standard Specification for Flexible Cellular Rubber Chemically Blown |
ASTM D 7284 : 2020 | Standard Test Method for Total Cyanide in Water by Micro Distillation followed by Flow Injection Analysis with Gas Diffusion Separation and Amperometric Detection |
ASTM D 2197 : 2016 | Standard Test Method for Adhesion of Organic Coatings by Scrape Adhesion |
ASTM F 1446 : 2020 | Standard Test Methods for Equipment and Procedures Used in Evaluating the Performance Characteristics of Protective Headgear |
ASTM D 6038 : 2021 | Standard Test Methods for Determining the Compatibility of Resin/Solvent Mixtures by Precipitation Temperature (Cloud Point) |
ASTM C 1773 : 2017 | Standard Test Method for Monotonic Axial Tensile Behavior of Continuous Fiber-Reinforced Advanced Ceramic Tubular Test Specimens at Ambient Temperature |
ASTM C 1446 : 2019 | Standard Test Method for Measuring Consistency of Self-Flowing Castable Refractories |
ASTM F 1291 : 2016 | Standard Test Method for Measuring the Thermal Insulation of Clothing Using a Heated Manikin |
ASTM C 473 : 2019 | Standard Test Methods for Physical Testing of Gypsum Panel Products |
ASTM G 69 : 2020 | Standard Test Method for Measurement of Corrosion Potentials of Aluminum Alloys |
ASTM E 1165 : 2020 | Standard Test Method for Measurement of Focal Spots of Industrial X-Ray Tubes by Pinhole Imaging |
ASTM D 4058 : 1996 : R2020 | Standard Test Method for Attrition and Abrasion of Catalysts and Catalyst Carriers |
ASTM D 2063/D2063M : 2010 : R2018 | Standard Test Methods for Measurement of Torque Retention for Packages with Continuous Thread Closures Using Non-Automated (Manual) Torque Testing Equipment |
ASTM G 192 : 2008 : R2020 : EDT 1 | Standard Test Method for Determining the Crevice Repassivation Potential of Corrosion-Resistant Alloys Using a Potentiodynamic-Galvanostatic-Potentiostatic Technique |
ASTM D 1686 : 2019 | Standard Test Method for Color of Solid Aromatic Hydrocarbons and Related Materials in the Molten State (Platinum-Cobalt Scale) |
ASTM D 6631 : 2005 : R2019 | Standard Guide for Committee D01 for Conducting an Interlaboratory Study for the Purpose of Determining the Precision of a Test Method |
ASTM D 6110 : 2018 | Standard Test Method for Determining the Charpy Impact Resistance of Notched Specimens of Plastics |
ASTM B 311 : 2017 | Standard Test Method for Density of Powder Metallurgy (PM) Materials Containing Less Than Two Percent Porosity |
ASTM F 152 : 1995 : R2017 | Standard Test Methods for Tension Testing of Nonmetallic Gasket Materials |
ASTM G 48 : 2011 : R2020 : EDT 1 | Standard Test Methods for Pitting and Crevice Corrosion Resistance of Stainless Steels and Related Alloys by Use of Ferric Chloride Solution |
ASTM E 1323 : 2015 : R2020 | Standard Guide for Evaluating Laboratory Measurement Practices and the Statistical Analysis of the Resulting Data |
ASTM D 6132 : 2013 : R2017 | Standard Test Method for Nondestructive Measurement of Dry Film Thickness of Applied Organic Coatings Using an Ultrasonic Coating Thickness Gage |
ASTM D 1623 : 2017 | Standard Test Method for Tensile and Tensile Adhesion Properties of Rigid Cellular Plastics |
ASTM C 1606 : 2010 : R2018 | Standard Test Method for Sampling Protocol for TCLP Testing of Container Glassware |
ASTM D 5048 : 2020 : REV A | Standard Test Method for Measuring the Comparative Burning Characteristics and Resistance to Burn-Through of Solid Plastics Using a 125-mm Flame |
ASTM D 698 : 2012 : EDT 2 | Standard Test Methods for Laboratory Compaction Characteristics of Soil Using Standard Effort (12 400 ft-lbf/ft<sup>3</sup> (600 kN-m/m<sup>3</sup>)) |
ASTM D 7843 : 2018 | Standard Test Method for Measurement of Lubricant Generated Insoluble Color Bodies in In-Service Turbine Oils using Membrane Patch Colorimetry |
ASTM D 4796 : 2017 | Standard Test Method for Bond Strength of Thermoplastic Pavement Marking Materials |
ASTM D 6855 : 2017 | Standard Test Method for Determination of Turbidity Below 5 NTU in Static Mode |
ASTM B 212 : 2017 | Standard Test Method for Apparent Density of Free-Flowing Metal Powders Using the Hall Flowmeter Funnel |
ASTM D 2866 : 2011 : R2018 | Standard Test Method for Total Ash Content of Activated Carbon |
ASTM E 96/E96M : 2016 | Standard Test Methods for Water Vapor Transmission of Materials |
ASTM D 6580 : 2017 | Standard Test Method for The Determination of Metallic Zinc Content in Both Zinc Dust Pigment and in Cured Films of Zinc-Rich Coatings |
ASTM D 5766/D5766M : 2011 : R2018 | Standard Test Method for Open-Hole Tensile Strength of Polymer Matrix Composite Laminates |
ASTM D 5994/D5994M : 2010 : R2015 : EDT 1 | Standard Test Method for Measuring Core Thickness of Textured Geomembranes |
ASTM D 5074 : 1990 : R2019 : EDT 1 | Standard Practice for Preparation of Natural-Matrix Sediment Reference Samples for Major and Trace Inorganic Constituents Analysis by Partial Extraction Procedures |
ASTM D 2519 : 2019 : REV A | Standard Test Method for Bond Strength of Electrical Insulating Varnishes by the Helical Coil Test |
ASTM F 1632 : 2003 : R2018 | Standard Test Method for Particle Size Analysis and Sand Shape Grading of Golf Course Putting Green and Sports Field Rootzone Mixes |
ASTM D 4672 : 2018 | Standard Test Method for Polyurethane Raw Materials: Determination of Water Content of Polyols |
ASTM E 246 : 2010 : R2015 | Standard Test Methods for Determination of Iron in Iron Ores and Related Materials by Dichromate Titrimetry |
ASTM D 7100 : 2011 : R2020 | Standard Test Method for Hydraulic Conductivity Compatibility Testing of Soils with Aqueous Solutions |
ASTM C 471M : 2020 : REV A | Standard Test Methods for Chemical Analysis of Gypsum and Gypsum Products (Metric) |
ASTM D 3967 : 2016 | Standard Test Method for Splitting Tensile Strength of Intact Rock Core Specimens |
ASTM D 7882 : 2020 | Standard Test Method for Determination of 4-Carboxybenzaldehyde and <emph type="bdit" >p</emph>-Toluic Acid in Purified Terephthalic Acid by Capillary Electrophoresis with Normal Voltage Mode |
ASTM D 3467 : 2004 : R2020 | Standard Test Method for Carbon Tetrachloride Activity of Activated Carbon |
ASTM D 7977 : 2019 | Standard Test Methods for Polymer Content of AMS (α-Methylstyrene) |
ASTM F 2251 : 2013 : R2018 | Standard Test Method for Thickness Measurement of Flexible Packaging Material |
ASTM F 2013 : 2010 : R2016 | Standard Test Method for Determination of Residual Acetaldehyde in Polyethylene Terephthalate Bottle Polymer Using an Automated Static Head-Space Sampling Device and a Capillary GC with a Flame Ionization Detector |
ASTM D 4716/D4716M : 2020 | Standard Test Method for Determining the (In-plane) Flow Rate per Unit Width and Hydraulic Transmissivity of a Geosynthetic Using a Constant Head |
ASTM D 7011 : 2015 : R2019 | Standard Test Method for Determination of Trace Thiophene in Refined Benzene by Gas Chromatography and Sulfur Selective Detection |
ASTM E 810 : 2020 | Standard Test Method for Coefficient of Retroreflection of Retroreflective Sheeting Utilizing the Coplanar Geometry |
ASTM F 2853 : 2010 : R2015 | Standard Test Method for Determination of Lead in Paint Layers and Similar Coatings or in Substrates and Homogenous Materials by Energy Dispersive X-Ray Fluorescence Spectrometry Using Multiple Monochromatic Excitation Beams |
ASTM E 202 : 2018 | Standard Test Methods for Analysis of Ethylene Glycols and Propylene Glycols |
ASTM G 152 : 2013 | Standard Practice for Operating Open Flame Carbon Arc Light Apparatus for Exposure of Nonmetallic Materials |
ASTM D 3505 : 2018 | Standard Test Method for Density or Relative Density of Pure Liquid Chemicals (Withdrawn 2023) |
ASTM F 218 : 2013 : R2020 | Standard Test Method for Measuring Optical Retardation and Analyzing Stress in Glass |
ASTM G 132 : 1996 : R2018 | Standard Test Method for Pin Abrasion Testing |
ASTM E 2931 : 2013 : R2019 | Standard Test Method for Limiting Oxygen (Oxidant) Concentration of Combustible Dust Clouds |
ASTM D 5187 : 2021 | Standard Test Method for Determination of Crystallite Size (L<inf>c</inf>) of Calcined Petroleum Coke by X-Ray Diffraction |
ASTM D 7553 : 2015 | Standard Test Method for Solubility of Asphalt Materials in N-Propyl Bromide |
ASTM C 1421 : 2018 | Standard Test Methods for Determination of Fracture Toughness of Advanced Ceramics at Ambient Temperature |
ASTM F 3136 : 2015 | Standard Test Method for Oxygen Gas Transmission Rate through Plastic Film and Sheeting using a Dynamic Accumulation Method |
ASTM C 1113/C1113M : 2009 : R2019 | Standard Test Method for Thermal Conductivity of Refractories by Hot Wire (Platinum Resistance Thermometer Technique) |
ASTM F 1362 : 2018 | Standard Test Method for Shear Strength and Shear Modulus of Aerospace Glazing Interlayer Materials |
ASTM F 373 : 2013 : R2017 | Standard Test Method for Embossed Depth of Resilient Floor Coverings |
ASTM C 1485 : 2019 | Standard Test Method for Critical Radiant Flux of Exposed Attic Floor Insulation Using an Electric Radiant Heat Energy Source |
ASTM F 2370 : 2016 | Standard Test Method for Measuring the Evaporative Resistance of Clothing Using a Sweating Manikin |
ASTM D 4824 : 2013 : R2018 | Standard Test Method for Determination of Catalyst Acidity by Ammonia Chemisorption |
ASTM D 4438 : 2013 : R2018 : EDT 1 | Standard Test Method for Particle Size Distribution of Catalysts and Catalyst Carriers by Electronic Counting |
ASTM D 7084 : 2018 | Standard Test Method for Determination of Bulk Crush Strength of Catalysts and Catalyst Carriers |
ASTM C 1814/C1814M : 2020 | Standard Test Method for Measurement of Hydraulic Characteristics of Stormwater Filtration Elements |
ASTM D 6525/D6525M : 2018 | Standard Test Method for Measuring Nominal Thickness of Rolled Erosion Control Products |
ASTM D 8133 : 2021 | Standard Test Method for Determination of Low Level Phthalates in Poly(Vinyl Chloride) Plastics by Solvent Extraction—Gas Chromatography/Mass Spectrometry |
ASTM F 2129 : 2019 : REV A | Standard Test Method for Conducting Cyclic Potentiodynamic Polarization Measurements to Determine the Corrosion Susceptibility of Small Implant Devices |
ASTM C 958 : 1992 : R2014 | Standard Test Method for Particle Size Distribution of Alumina or Quartz by X-Ray Monitoring of Gravity Sedimentation |
ASTM D 6460 : 2019 | Standard Test Method for Determination of Rolled Erosion Control Product (RECP) Performance in Protecting Earthen Channels from Stormwater-Induced Erosion |
ASTM D 4481 : 2010 : R2015 | Standard Test Method for Total Nickel in Fresh Alumina-Base Catalysts |
ASTM D 7477 : 2016 | Standard Test Method for Determining the Area Stability of Wet Blue Submersed in Boiling Water |
ASTM D 3368 : 2017 | Standard Specification for FEP Sheet and Film |
ASTM D 5890 : 2019 | Standard Test Method for Swell Index of Clay Mineral Component of Geosynthetic Clay Liners |
ASTM B 963 : 2017 | Standard Test Methods for Oil Content, Oil-Impregnation Efficiency, and Surface-Connected Porosity of Sintered Powder Metallurgy (PM) Products Using Archimedes’ Principle |
ASTM D 2765 : 2016 | Standard Test Methods for Determination of Gel Content and Swell Ratio of Crosslinked Ethylene Plastics |
ASTM E 1414/E1414M : 2021 | Standard Test Method for Airborne Sound Attenuation Between Rooms Sharing a Common Ceiling Plenum |
ASTM D 5630 : 2013 | Standard Test Method for Ash Content in Plastics (Withdrawn 2022) |
ASTM D 5673 : 2016 | Standard Test Method for Elements in Water by Inductively Coupled Plasma—Mass Spectrometry |
ASTM F 37 : 2006 : R2019 | Standard Test Methods for Sealability of Gasket Materials |
ASTM D 6474 : 2020 | Standard Test Method for Determining Molecular Weight Distribution and Molecular Weight Averages of Polyolefins by High Temperature Gel Permeation Chromatography |
ASTM D 7476 : 2008 : R2020 | Standard Test Method for Brine Saturation Value of Cured (Salt-Preserved) Hides and Skins |
ASTM D 36/D36M : 2014 : R2020 | Standard Test Method for Softening Point of Bitumen (Ring-and-Ball Apparatus) |
ASTM E 2546 : 2015 | Standard Practice for Instrumented Indentation Testing |
ASTM F 1264 : 2016 : EDT 1 | Standard Specification and Test Methods for Intramedullary Fixation Devices |
ASTM E 159 : 2017 | Standard Test Method for Loss of Mass in a Reducing Gas Atmosphere for Cobalt, Copper, Tungsten, and Iron Powders (Hydrogen Loss) |
ASTM E 1326 : 2020 | Standard Guide for Evaluating Non-culture Microbiological Tests |
ASTM D 6695 : 2016 | Standard Practice for Xenon-Arc Exposures of Paint and Related Coatings |
ASTM D 7184 : 2020 | Standard Test Method for Ultra Low Nitrogen in Aromatic Hydrocarbons by Oxidative Combustion and Reduced Pressure Chemiluminescence Detection |
ASTM D 7844 : 2020 | Standard Test Method for Condition Monitoring of Soot in In-Service Lubricants by Trend Analysis using Fourier Transform Infrared (FT-IR) Spectrometry |
ASTM D 6349 : 2013 | Standard Test Method for Determination of Major and Minor Elements in Coal, Coke, and Solid Residues from Combustion of Coal and Coke by Inductively Coupled Plasma—Atomic Emission Spectrometry |
ASTM E 1508 : 2012 : REV A : R2019 | Standard Guide for Quantitative Analysis by Energy-Dispersive Spectroscopy |
ASTM D 7817 : 2012 : R2016 | Standard Test Method for Enumeration of Yeast and Mold in Raceway Brine, Brine-Cured Hides and Skins |
ASTM D 2842 : 2019 | Standard Test Method for Water Absorption of Rigid Cellular Plastics |
ASTM E 21 : 2020 | Standard Test Methods for Elevated Temperature Tension Tests of Metallic Materials |
ASTM E 1021 : 2015 : R2019 | Standard Test Method for Spectral Responsivity Measurements of Photovoltaic Devices |
ASTM F 1647 : 2011 : R2018 | Standard Test Methods for Organic Matter Content of Athletic Field Rootzone Mixes |
ASTM E 2945 : 2014 | Standard Test Method for Film Permeability Determination Using Static Permeability Cells |
ASTM C 1104/C1104M : 2019 | Standard Test Method for Determining the Water Vapor Sorption of Unfaced Mineral Fiber Insulation |
ASTM A 343/A343M : 2014 : R2019 | Standard Test Method for Alternating-Current Magnetic Properties of Materials at Power Frequencies Using Wattmeter-Ammeter-Voltmeter Method and 25-cm Epstein Test Frame |
ASTM D 5419 : 2014 : REV A | Standard Test Method for Environmental Stress Crack Resistance (ESCR) of Threaded Plastic Closures |
ASTM D 4498 : 2007 : R2015 | Standard Test Method for Heat-Fail Temperature in Shear of Hot Melt Adhesives (Withdrawn 2021) |
ASTM D 5199 : 2012 : R2019 | Standard Test Method for Measuring the Nominal Thickness of Geosynthetics |
ASTM D 3160 : 2020 : REV A | Standard Test Method for Phenol Content of Cumene (Isopropylbenzene) or AMS (α–Methylstyrene) |
ASTM D 4642 : 2004 : R2016 | Standard Test Method for Platinum in Reforming Catalysts by Wet Chemistry |
ASTM C 1735 : 2017 | Standard Test Method for Measuring the Time Dependent Modulus of Sealants Using Stress Relaxation |
ASTM C 686 : 2017 | Standard Test Method for Parting Strength of Mineral Fiber Batt- and Blanket-Type Insulation |
ASTM D 6459 : 2019 | Standard Test Method for Determination of Rolled Erosion Control Product (RECP) Performance in Protecting Hillslopes from Rainfall-Induced Erosion |
ASTM C 695 : 2015 : R2020 | Standard Test Method for Compressive Strength of Carbon and Graphite |
ASTM D 5403 : 1993 : R2013 | Standard Test Methods for Volatile Content of Radiation Curable Materials |
ASTM D 7412 : 2018 | Standard Test Method for Condition Monitoring of Phosphate Antiwear Additives in In-Service Petroleum and Hydrocarbon Based Lubricants by Trend Analysis Using Fourier Transform Infrared (FT-IR) Spectrometry |
ASTM D 7661 : 2018 | Standard Test Method for Determining Compatibility of Personal Lubricants with Natural Rubber Latex Condoms |
ASTM E 2056 : 2004 : R2016 | Standard Practice for Qualifying Spectrometers and Spectrophotometers for Use in Multivariate Analyses, Calibrated Using Surrogate Mixtures |
ASTM A 833 : 2019 | Standard Test Method for Indentation Hardness of Metallic Materials by Comparison Hardness Testers |
ASTM D 4890 : 2018 | Standard Test Methods for Polyurethane Raw Materials: Determination of Gardner and APHA Color of Polyols |
ASTM B 822 : 2020 | Standard Test Method for Particle Size Distribution of Metal Powders and Related Compounds by Light Scattering |
ASTM D 6419 : 2000 : R2017 | Standard Test Method for Volatile Content of Sheet-Fed and Coldset Web Offset Printing Inks |
ASTM D 7812 : 2016 | Standard Test Method for Tensile Testing of Aramid Paper |
ASTM D 7637 : 2010 : R2015 | Standard Test Method for Determination of Glycerin Assay by Titration (Sodium Meta Periodate) |
ASTM F 2263 : 2014 : R2019 | Standard Test Method for Evaluating the Oxidative Resistance of Polyethylene (PE) Pipe to Chlorinated Water |
ASTM D 1977 : 2016 | Standard Test Method for Nickel and Vanadium in FCC Equilibrium Catalysts by Hydrofluoric/Sulfuric Acid Decomposition and Atomic Spectroscopic Analysis |
ASTM E 2242 : 2013 | Standard Test Method for Column Percolation Extraction of Mine Rock by the Meteoric Water Mobility Procedure |
ASTM D 8089 : 2017 | Standard Practice for Accelerated Heat Aging for Floor Covering Adhesives |
ASTM E 2427 : 2018 | Standard Test Method for Acceptance by Performance Testing for Sieves |
ASTM D 5755 : 2009 : R2014 : EDT 1 | Standard Test Method for Microvacuum Sampling and Indirect Analysis of Dust by Transmission Electron Microscopy for Asbestos Structure Number Surface Loading (Withdrawn 2023) |
ASTM D 6567 : 2018 | Standard Test Method for Measuring the Light Penetration of a Rolled Erosion Control Product (RECP) |
ASTM D 2867 : 2017 | Standard Test Methods for Moisture in Activated Carbon |
ASTM C 1763 : 2020 | Standard Test Method for Water Absorption by Immersion of Thermal Insulation Materials |
ASTM D 731 : 2018 | Standard Test Method for Molding Index of Thermosetting Molding Powder |
ASTM E 1921 : 2020 | Standard Test Method for Determination of Reference Temperature, <emph type="bdit">T<inf >o</inf></emph>, for Ferritic Steels in the Transition Range |
ASTM C 1382 : 2016 | Standard Test Method for Determining Tensile Adhesion Properties of Sealants When Used in Exterior Insulation and Finish Systems (EIFS) Joints |
ASTM F 2156 : 2017 | Standard Test Method for Measuring Optical Distortion in Transparent Parts Using Grid Line Slope |
ASTM D 6647 : 2018 | Standard Test Method for Determination of Acid Soluble Iron via Atomic Absorption |
ASTM D 6953 : 2018 | Standard Test Method for Determination of Antioxidants and Erucamide Slip Additives in Polyethylene Using Liquid Chromatography (LC) |
ASTM D 6575/D6575M : 2016 | Standard Test Method for Determining Stiffness of Geosynthetics Used as Turf Reinforcement Mats (TRMs) |
ASTM E 9 : 2019 | Standard Test Methods of Compression Testing of Metallic Materials at Room Temperature |
ASTM D 5229/D5229M : 2020 | Standard Test Method for Moisture Absorption Properties and Equilibrium Conditioning of Polymer Matrix Composite Materials |
ASTM F 1951 : 2014 | Standard Specification for Determination of Accessibility of Surface Systems Under and Around Playground Equipment |
ASTM F 2508 : 2016 : EDT 1 | Standard Practice for Validation, Calibration, and Certification of Walkway Tribometers Using Reference Surfaces |
ASTM D 6906 : 2012 : REV A : R2016 | Standard Test Method for Determination of Titanium Treatment Weight on Metal Substrates by Wavelength Dispersive X-Ray Fluorescence |
ASTM D 5153 : 2010 : R2016 | Standard Test Method for Palladium in Molecular Sieve Catalyst by Atomic Absorption |
ASTM F 410 : 2008 : R2017 | Standard Test Method for Wear Layer Thickness of Resilient Floor Coverings by Optical Measurement |
ASTM E 1680 : 2016 | Standard Test Method for Rate of Air Leakage through Exterior Metal Roof Panel Systems |
ASTM D 2232 : 2014 : R2018 | Standard Test Method for Evaporating Residue of Naphthalene |
ASTM D 7767 : 2011 : R2018 | Standard Test Method to Measure Volatiles from Radiation Curable Acrylate Monomers, Oligomers, and Blends and Thin Coatings Made from Them |
ASTM D 5225 : 2017 | Standard Test Method for Measuring Solution Viscosity of Polymers with a Differential Viscometer |
ASTM F 1249 : 2020 | Standard Test Method for Water Vapor Transmission Rate Through Plastic Film and Sheeting Using a Modulated Infrared Sensor |
ASTM F 1438 : 1993 : R2020 | Standard Test Method for Determination of Surface Roughness by Scanning Tunneling Microscopy for Gas Distribution System Components (Withdrawn 2023) |
ASTM F 1921/F1921M : 2012 : R2018 | Standard Test Methods for Hot Seal Strength (Hot Tack) of Thermoplastic Polymers and Blends Comprising the Sealing Surfaces of Flexible Webs |
ASTM D 7748/D7748M : 2014 : EDT 1 | Standard Test Method for Flexural Rigidity of Geogrids, Geotextiles and Related Products |
ASTM D 256 : 2010 : R2018 | Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics |
ASTM D 3174 : 2012 : R2018 : EDT 1 | Standard Test Method for Ash in the Analysis Sample of Coal and Coke from Coal |
ASTM D 3953 : 2015 | Standard Specification for Strapping, Flat Steel and Seals |
ASTM C 1012/C1012M : 2018 : REV B | Standard Test Method for Length Change of Hydraulic-Cement Mortars Exposed to a Sulfate Solution |
ASTM D 6281 : 2015 | Standard Test Method for Airborne Asbestos Concentration in Ambient and Indoor Atmospheres as Determined by Transmission Electron Microscopy Direct Transfer (TEM) |
ASTM D 882 : 2018 | Standard Test Method for Tensile Properties of Thin Plastic Sheeting |
ASTM D 6761 : 2017 | Standard Test Method for Determination of the Total Pore Volume of Catalysts and Catalyst Carriers |
ASTM D 4590 : 2018 | Standard Test Method for Colorimetric Determination of <emph type="ital">p-tert</emph >-Butylcatechol In Styrene Monomer or AMS (α–Methylstyrene) by Spectrophotometry |
ASTM F 1284 : 2009 : R2016 | Standard Test Method for Evaluating Carpet Embedded Dirt Removal Effectiveness of Residential Central Vacuum Cleaning Systems |
ASTM E 247 : 2001 : R2015 : EDT 1 | Standard Test Method for Determination of Silica in Manganese Ores, Iron Ores, and Related Materials by Gravimetry |
ASTM D 5296 : 2019 | Standard Test Method for Molecular Weight Averages and Molecular Weight Distribution of Polystyrene by High Performance Size-Exclusion Chromatography |
ASTM D 4208 : 2019 | Standard Test Method for Total Chlorine in Coal by the Oxygen Vessel Combustion/Ion Selective Electrode Method |
ASTM D 4179 : 2011 : R2017 | Standard Test Method for Single Pellet Crush Strength of Formed Catalysts and Catalyst Carriers |
ASTM D 6583 : 2013 : R2019 | Standard Test Method for Porosity of Paint Film by Mineral Oil Absorption |
ASTM E 291 : 2018 | Standard Test Methods for Chemical Analysis of Caustic Soda and Caustic Potash (Sodium Hydroxide and Potassium Hydroxide) |
ASTM D 5329 : 2020 | Standard Test Methods for Sealants and Fillers, Hot-Applied, for Joints and Cracks in Asphalt Pavements and Portland Cement Concrete Pavements |
ASTM F 2778 : 2009 : R2020 | Standard Test Method for Measurement of Percent Crystallinity of Polyetheretherketone (PEEK) Polymers by Means of Specular Reflectance Fourier Transform Infrared Spectroscopy (R-FTIR) |
ASTM F 3189 : 2020 | Standard Test Method for Measuring Force Reduction, Vertical Deformation, and Energy Restitution of Synthetic Turf Systems Using the Advanced Artificial Athlete |
ASTM D 4782 : 2010 : R2016 | Standard Test Method for Palladium in Molecular Sieve Catalyst by Wet Chemistry |
ASTM D 4944 : 2018 | Standard Test Method for Field Determination of Water (Moisture) Content of Soil by the Calcium Carbide Gas Pressure Tester |
ASTM D 5744 : 2018 | Standard Test Method for Laboratory Weathering of Solid Materials Using a Humidity Cell |
ASTM D 5031/D5031M : 2013 : R2018 | Standard Practice for Enclosed Carbon-Arc Exposure Tests of Paint and Related Coatings |
ASTM D 6099 : 2018 | Standard Test Method for Polyurethane Raw Materials: Determination of Acidity in Moderate to High Acidity Aromatic Isocyanates |
ASTM D 4685/D4685M : 2015 : R2020 | Standard Test Method for Pile Fabric Abrasion |
ASTM D 6809 : 2020 : REV A | Standard Guide for Quality Control and Quality Assurance Procedures for Aromatic Hydrocarbons and Related Materials |
ASTM D 5528 : 2013 | Standard Test Method for Mode I Interlaminar Fracture Toughness of Unidirectional Fiber-Reinforced Polymer Matrix Composites |
ASTM D 6475 : 2017 | Standard Test Method for Measuring Mass per Unit Area of Erosion Control Blankets |
ASTM B 329 : 2020 | Standard Test Method for Apparent Density of Metal Powders and Compounds Using the Scott Volumeter |
ASTM D 1475 : 2013 : R2020 | Standard Test Method for Density of Liquid Coatings, Inks, and Related Products |
ASTM D 7708 : 2014 | Standard Test Method for Microscopical Determination of the Reflectance of Vitrinite Dispersed in Sedimentary Rocks |
ASTM C 1246 : 2017 | Standard Test Method for Effects of Heat Aging on Weight Loss, Cracking, and Chalking of Elastomeric Sealants After Cure |
ASTM B 647 : 2010 : R2016 | Standard Test Method for Indentation Hardness of Aluminum Alloys by Means of a Webster Hardness Gage |
ASTM D 5154/D5154M : 2018 | Standard Test Method for Determining Activity and Selectivity of Fluid Catalytic Cracking (FCC) Catalysts by Microactivity Test |
ASTM D 6150 : 2016 | Standard Test Method for Estimating Processing Losses of Plastisols and Organosols Due to Volatility |
ASTM E 8/E8M : 2021 | Standard Test Methods for Tension Testing of Metallic Materials |
ASTM D 6558 : 2000 : REV A : R2015 : EDT 1 | Standard Test Method for Determination of TGA CO<inf>2</inf> Reactivity of Baked Carbon Anodes and Cathode Blocks |
ASTM D 5917 : 2015 : R2019 | Standard Test Method for Trace Impurities in Monocyclic Aromatic Hydrocarbons by Gas Chromatography and External Calibration |
ASTM D 4459 : 2021 | Standard Practice for Xenon-Arc Exposure of Plastics Intended for Indoor Applications |
ASTM D 3963/D3963M : 2015 | Standard Specification for Fabrication and Jobsite Handling of Epoxy-Coated Steel Reinforcing Bars |
ASTM D 1140 : 2017 | Standard Test Methods for Determining the Amount of Material Finer than 75-μm (No. 200) Sieve in Soils by Washing |
ASTM D 5018 : 2018 | Standard Test Method for Shear Viscosity of Coal-Tar and Petroleum Pitches |
ASTM E 2677 : 2020 | Standard Test Method for Estimating Limits of Detection in Trace Detectors for Explosives and Drugs of Interest |
ASTM A 428/A428M : 2010 : R2019 | Standard Test Method for Weight [Mass] of Coating on Aluminum-Coated Iron or Steel Articles |
ASTM D 1987 : 2018 | Standard Test Method for Biological Clogging of Geotextile or Soil/Geotextile Filters |
ASTM C 165 : 2007 : R2017 | Standard Test Method for Measuring Compressive Properties of Thermal Insulations |
ASTM C 1720 : 2017 : EDT 1 | Standard Test Method for Determining Liquidus Temperature of Waste Glasses and Simulated Waste Glasses |
ASTM C 1662 : 2018 | Standard Practice for Measurement of the Glass Dissolution Rate Using the Single-Pass Flow-Through Test Method |
ASTM D 7984 : 2016 | Standard Test Method for Measurement of Thermal Effusivity of Fabrics Using a Modified Transient Plane Source (MTPS) Instrument |
ASTM D 3975 : 1993 : R2019 | Standard Practice for Development and Use (Preparation) of Samples for Collaborative Testing of Methods for Analysis of Sediments |
ASTM D 7536 : 2020 | Standard Test Method for Chlorine in Aromatics by Monochromatic Wavelength Dispersive X-ray Fluorescence Spectrometry |
ASTM B 797 : 2020 | Standard Test Method for Surface Finger-Oxide Penetration Depth and Presence of Interparticle Oxide Networks in Powder Forged (PF) Steel Parts |
ASTM D 2584 : 2018 | Standard Test Method for Ignition Loss of Cured Reinforced Resins |
ASTM D 3492 : 2016 | Standard Specification for Rubber Contraceptives (Male Condoms) |
ASTM D 7535 : 2009 : R2015 | Standard Test Method for Lead-210 in Water (Withdrawn 2024) |
ASTM D 955 : 2008 : R2014 | Standard Test Method of Measuring Shrinkage from Mold Dimensions of Thermoplastics |
ASTM D 3032 : 2021 | Standard Test Methods for Hookup Wire Insulation |
ASTM D 952 : 2015 | Standard Test Method for Bond or Cohesive Strength of Sheet Plastics and Electrical Insulating Materials |
ASTM D 7043 : 2017 | Standard Test Method for Indicating Wear Characteristics of Non-Petroleum and Petroleum Hydraulic Fluids in a Constant Volume Vane Pump |
ASTM D 1331 : 2020 | Standard Test Methods for Surface and Interfacial Tension of Solutions of Paints, Solvents, Solutions of Surface-Active Agents, and Related Materials |
ASTM D 8314 : 2020 | Standard Guide for Performance Testing of Applied Stretch Films and Stretch Wrapping |
ASTM D 4329 : 2013 | Standard Practice for Fluorescent Ultraviolet (UV) Lamp Apparatus Exposure of Plastics |
ASTM F 3313 : 2020 | Standard Test Method for Determining Impact Attenuation of Playground Surfaces Within the Use Zone of Playground Equipment as Tested in the Field |
ASTM D 5572 : 1995 : R2019 | Standard Specification for Adhesives Used for Finger Joints in Nonstructural Lumber Products |
ASTM D 3908 : 2020 | Standard Test Method for Hydrogen Chemisorption on Supported Platinum Catalysts by Volumetric Vacuum Method |
ASTM C 1215 : 2018 | Standard Guide for Preparing and Interpreting Precision and Bias Statements in Test Method Standards Used in the Nuclear Industry |
ASTM D 4254 : 2016 | Standard Test Methods for Minimum Index Density and Unit Weight of Soils and Calculation of Relative Density |
ASTM D 3241 : 2020 : REV C | Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels |
ASTM C 1271 : 1999 : R2020 | Standard Test Method for X-ray Spectrometric Analysis of Lime and Limestone |
ASTM D 1155 : 2010 : R2020 | Standard Test Method for Roundness of Glass Spheres |
ASTM D 8167/D8167M : 2018 : REV A | Standard Test Method for In-Place Bulk Density of Soil and Soil-Aggregate by a Low-Activity Nuclear Method (Shallow Depth) |
ASTM D 7778 : 2015 | Standard Guide for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
ASTM D 5767 : 2018 | Standard Test Method for Instrumental Measurement of Distinctness-of-Image (DOI) Gloss of Coated Surfaces |
ASTM C 177 : 2019 | Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus |
ASTM D 854 : 2014 | Standard Test Methods for Specific Gravity of Soil Solids by Water Pycnometer (Withdrawn 2023) |
ASTM D 7674 : 2014 : REV A | Standard Test Method for Hexane/Petroleum Ether Extract in Wet Blue and Wet White |
ASTM D 4632/D4632M : 2015 : REV A | Standard Test Method for Grab Breaking Load and Elongation of Geotextiles |
ASTM C 670 : 2015 | Standard Practice for Preparing Precision and Bias Statements for Test Methods for Construction Materials |
ASTM E 2141 : 2014 | Standard Test Method for Accelerated Aging of Electrochromic Devices in Sealed Insulating Glass Units |
ASTM D 3175 : 2020 | Standard Test Method for Volatile Matter in the Analysis Sample of Coal and Coke |
ASTM E 70 : 2019 | Standard Test Method for pH of Aqueous Solutions With the Glass Electrode |
ASTM E 1709 : 2016 : EDT 2 | Standard Test Method for Measurement of Retroreflective Signs Using a Portable Retroreflectometer at a 0.2 Degree Observation Angle |
ASTM D 6115 : 1997 : R2019 | Standard Test Method for Mode I Fatigue Delamination Growth Onset of Unidirectional Fiber-Reinforced Polymer Matrix Composites |
ASTM F 2077 : 2018 | Test Methods For Intervertebral Body Fusion Devices |
ASTM C 978 : 2004 : R2019 | Standard Test Method for Photoelastic Determination of Residual Stress in a Transparent Glass Matrix Using a Polarizing Microscope and Optical Retardation Compensation Procedures |
ASTM D 8380 : 2021 | Standard Test Method for Dry Abrasion Resistance of Hydrophobic and Omniphobic Coatings |
ASTM B 933 : 2020 | Standard Test Method for Microindentation Hardness of Powder Metallurgy (PM) Materials |
ASTM G 81 : 1997 : REV A : R2018 | Standard Test Method for Jaw Crusher Gouging Abrasion Test |
ASTM D 198 : 2015 | Standard Test Methods of Static Tests of Lumber in Structural Sizes |
ASTM D 7704 : 2016 | Standard Test Method for Total Aldehydes in Styrene Monomer by Potentiometric Titration |
ASTM C 1292 : 2016 | Standard Test Method for Shear Strength of Continuous Fiber-Reinforced Advanced Ceramics at Ambient Temperatures |
ASTM E 3205 : 2020 | Standard Test Method for Small Punch Testing of Metallic Materials |
ASTM F 1315 : 2017 | Standard Test Method for Density of a Sheet Gasket Material |
ASTM D 2538 : 2018 | Standard Practice for Fusion of Poly(Vinyl Chloride) (PVC) Compounds Using a Torque Rheometer |
ASTM C 1667 : 2015 | Standard Test Method for Using Heat Flow Meter Apparatus to Measure the Center-of-Panel Thermal Transmission Properties of Vacuum Insulation Panels |
ASTM D 5768 : 2002 : R2018 | Standard Test Method for Determination of Iodine Value of Tall Oil Fatty Acids |
ASTM E 572 : 2013 | Standard Test Method for Analysis of Stainless and Alloy Steels by Wavelength Dispersive X-Ray Fluorescence Spectrometry |
ASTM E 248 : 2012 | Standard Test Method for Determination of Manganese in Manganese Ores by Pyrophosphate Complexed Permanganate Potentiometric Titrimetry |
ASTM F 1593 : 2008 : R2016 | Standard Test Method for Trace Metallic Impurities in Electronic Grade Aluminum by High Mass-Resolution Glow-Discharge Mass Spectrometer (Withdrawn 2023) |
ASTM C 302 : 2013 : R2017 | Standard Test Method for Density and Dimensions of Preformed Pipe-Covering-Type Thermal Insulation |
ASTM F 2979 : 2020 | Standard Guide for Characterization of Wear from the Articulating Surfaces in Retrieved Metal-on-Metal and other Hard-on-Hard Hip Prostheses |
ASTM D 480 : 1988 : R2020 | Standard Test Methods for Sampling and Testing of Flaked Aluminum Powders and Pastes |
ASTM D 3403 : 2007 : R2016 | Standard Test Methods for Rubber—Evaluation of IR (Isoprene Rubber) |
ASTM D 4284 : 2012 : R2017 : EDT 1 | Standard Test Method for Determining Pore Volume Distribution of Catalysts and Catalyst Carriers by Mercury Intrusion Porosimetry |
ASTM G 57 : 2020 | Standard Test Method for Measurement of Soil Resistivity Using the Wenner Four-Electrode Method |
ASTM D 7065 : 2017 | Standard Test Method for Determination of Nonylphenol, Bisphenol A, <emph type="bdit" >p-tert</emph>-Octylphenol, Nonylphenol Monoethoxylate and Nonylphenol Diethoxylate in Environmental Waters by Gas Chromatography Mass Spectrometry |
ASTM D 7252 : 2017 | Standard Test Method for Polyurethane Raw Materials: Determination of Monomer and Isomers in Isocyanates |
ASTM D 4754 : 2018 | Standard Test Method for Two-Sided Liquid Extraction of Plastic Materials Using FDA Migration Cell |
ASTM E 112 : 2013 | Standard Test Methods for Determining Average Grain Size |
ASTM C 25 : 2019 | Standard Test Methods for Chemical Analysis of Limestone, Quicklime, and Hydrated Lime |
ASTM E 1036 : 2015 : R2019 | Standard Test Methods for Electrical Performance of Nonconcentrator Terrestrial Photovoltaic Modules and Arrays Using Reference Cells |
ASTM D 5751 : 1999 : R2019 | Standard Specification for Adhesives Used for Laminate Joints in Nonstructural Lumber Products |
ASTM E 2948 : 2016 : REV A | Standard Test Method for Conducting Rotating Bending Fatigue Tests of Solid Round Fine Wire |
ASTM A 956/A956M : 2017 : REV A | Standard Test Method for Leeb Hardness Testing of Steel Products |
ASTM D 1875 : 2003 : R2018 | Standard Test Method for Density of Adhesives in Fluid Form |
ASTM D 7855/D7855M : 2013 : R2017 | Standard Test Method for Determination of Mold Growth on Coated Building Products Designed for Interior Applications Using an Environmental Chamber and Indirect Inoculation |
ASTM E 23 : 2018 | Standard Test Methods for Notched Bar Impact Testing of Metallic Materials |
ASTM G 202 : 2012 : R2020 | Standard Test Method for Using Atmospheric Pressure Rotating Cage |
ASTM D 5946 : 2017 | Standard Test Method for Corona-Treated Polymer Films Using Water Contact Angle Measurements |
ASTM D 4093 : 1995 : R2014 | Standard Test Method for Photoelastic Measurements of Birefringence and Residual Strains in Transparent or Translucent Plastic Materials |
ASTM D 4780 : 2012 : R2017 : EDT 1 | Standard Test Method for Determination of Low Surface Area of Catalysts and Catalyst Carriers by Multipoint Krypton Adsorption |
ASTM F 2105 : 2021 | Standard Test Method for Measuring Air Performance Characteristics of Vacuum Cleaner Motor/Fan Systems |
ASTM E 278 : 2001 : R2015 : EDT 1 | Standard Test Method for Determination of Phosphorus in Iron Ores by Phosphomolybdate Coprecipitation and Nitric Acid Titrimetry |
ASTM E 698 : 2018 | Standard Test Method for Kinetic Parameters for Thermally Unstable Materials Using Differential Scanning Calorimetry and the Flynn/Wall/Ozawa Method |
ASTM D 6480 : 2019 | Standard Test Method for Wipe Sampling of Surfaces, Indirect Preparation, and Analysis for Asbestos Structure Number Surface Loading by Transmission Electron Microscopy |
ASTM F 2569 : 2011 : R2019 | Standard Test Method for Evaluating the Force Reduction Properties of Surfaces for Athletic Use |
ASTM B 923 : 2020 | Standard Test Method for Metal Powder Skeletal Density by Helium or Nitrogen Pycnometry |
ASTM C 800 : 2019 | Standard Specification for Fibrous Glass Blanket Insulation (Aircraft Type) |
ASTM D 7466/D7466M : 2010 : R2015 : EDT 1 | Standard Test Method for Measuring Asperity Height of Textured Geomembranes |
ASTM D 3835 : 2016 | Standard Test Method for Determination of Properties of Polymeric Materials by Means of a Capillary Rheometer |
ASTM D 6980 : 2017 | Standard Test Method for Determination of Moisture in Plastics by Loss in Weight |
ASTM E 399 : 2020 : REV A | Standard Test Method for Linear-Elastic Plane-Strain Fracture Toughness of Metallic Materials |
ASTM D 465 : 2015 : R2020 | Standard Test Methods for Acid Number of Pine Chemical Products Including Tall Oil and Other Related Products |
ASTM C 739 : 2017 | Standard Specification for Cellulosic Fiber Loose-Fill Thermal Insulation |
ASTM D 5449/D5449M : 2016 | Standard Test Method for Transverse Compressive Properties of Hoop Wound Polymer Matrix Composite Cylinders |
ASTM C 1872 : 2018 : EDT 2 | Standard Test Method for Thermogravimetric Analysis of Hydraulic Cement |
ASTM D 7779 : 2020 | Standard Test Method for Determination of Fracture Toughness of Graphite at Ambient Temperature |
ASTM E 1641 : 2018 | Standard Test Method for Decomposition Kinetics by Thermogravimetry Using the Ozawa/Flynn/Wall Method |
ASTM D 8028 : 2017 | Standard Test Method for Measurement of Dissolved Gases Methane, Ethane, Ethylene, and Propane by Static Headspace Sampling and Flame Ionization Detection (GC/FID) |
ASTM D 1938 : 2019 | Standard Test Method for Tear-Propagation Resistance (Trouser Tear) of Plastic Film and Thin Sheeting by a Single-Tear Method |
ASTM E 1856 : 2013 | Standard Guide for Evaluating Computerized Data Acquisition Systems Used to Acquire Data from Universal Testing Machines |
ASTM D 8010 : 2018 | Standard Test Method for Determination of Water Soluble Alkali Content in Coal |
ASTM E 1251 : 2017 : REV A | Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Spark Atomic Emission Spectrometry |
ASTM D 5208 : 2014 | Standard Practice for Fluorescent Ultraviolet (UV) Exposure of Photodegradable Plastics |
ASTM D 3826 : 2018 | Standard Practice for Determining Degradation End Point in Degradable Polyethylene and Polypropylene Using a Tensile Test |
ASTM E 1131 : 2020 | Standard Test Method for Compositional Analysis by Thermogravimetry |
ASTM E 2550 : 2017 | Standard Test Method for Thermal Stability by Thermogravimetry |
ASTM E 1458 : 2012 : R2016 | Standard Test Method for Calibration Verification of Laser Diffraction Particle Sizing Instruments Using Photomask Reticles |
ASTM D 7266 : 2013 : R2018 : EDT 1 | Standard Test Method for Analysis of Cyclohexane by Gas Chromatography (External Standard) |
ASTM C 1374 : 2018 | Standard Test Method for Determination of Installed Thickness of Pneumatically Applied Loose-Fill Building Insulation |
ASTM D 4218 : 2020 | Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds by the Muffle-Furnace Technique |
ASTM D 6144 : 2017 | Standard Test Method for Analysis of AMS (α-Methylstyrene) by Capillary Gas Chromatography |
ASTM E 839 : 2011 : R2016 : EDT 1 | Standard Test Methods for Sheathed Thermocouples and Sheathed Thermocouple Cable |
ASTM D 1505 : 2018 | Standard Test Method for Density of Plastics by the Density-Gradient Technique |
ASTM D 2559 : 2012 : REV A : R2018 | Standard Specification for Adhesives for Bonded Structural Wood Products for Use Under Exterior Exposure Conditions |
ASTM D 5993 : 2018 | Standard Test Method for Measuring Mass per Unit Area of Geosynthetic Clay Liners |
ASTM G 187 : 2018 | Standard Test Method for Measurement of Soil Resistivity Using the Two-Electrode Soil Box Method |
ASTM D 2007 : 2019 | Standard Test Method for Characteristic Groups in Rubber Extender and Processing Oils and Other Petroleum-Derived Oils by the Clay-Gel Absorption Chromatographic Method |
ASTM D 5808 : 2020 | Standard Test Method for Determining Chloride in Aromatic Hydrocarbons and Related Chemicals by Microcoulometry |
ASTM D 1929 : 2020 | Standard Test Method for Determining Ignition Temperature of Plastics |
ASTM E 1169 : 2021 | Standard Practice for Conducting Ruggedness Tests |
ASTM E 456 : 2013 : REV A : R2017 : EDT 5 | Standard Terminology Relating to Quality and Statistics |
ASTM E 1169 : 2020 | Standard Practice for Conducting Ruggedness Tests |
ASTM E 456 : 2013 : REV A : R2017 : EDT 4 | Standard Terminology Relating to Quality and Statistics |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.