12/30257022 DC : 0
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BS EN 13611 - SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS OR LIQUID FUELS - GENERAL REQUIREMENTS
Available format(s)
Hardcopy , PDF
Superseded date
30-06-2015
Superseded by
Language(s)
English
Publisher
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Classification
5 Units of measurement and test conditions
6 Construction requirements
7 Performance
8 Electrical requirements
9 Electromagnetic compatibility (EMC)
10 Marking, installation and operating instructions
Annex A (informative) - Void
Annex B (informative) - Leak-tightness test for gas
controls - volumetric method
Annex C (informative) - Leak-tightness test for gas
controls - pressure loss method
Annex D (normative) - Conversion of pressure loss
into leakage rate
Annex E (normative) - Electrical/electronic component
fault modes
Annex F (normative) - Additional requirements for safety
accessories and pressure accessories as
defined in EU Directive 97/23/EC
Annex G (normative) - Materials for pressurized parts
Annex H (normative) - Additional materials for pressurized
parts
Annex I (normative) - Requirements for controls used in
DC supplied burners and appliances
burning gaseous or liquid fuels
Annex J (normative) - Method for the determination of a
Safety integrity level (SIL)
Annex K (normative) - Method for the determination of
a Performance Level (PL)
Annex L (informative) - Relationship between Safety
Integrity Level (SIL) and Performance
Level (PL)
Annex M (normative) - Reset functions
Annex N (informative) - Guidance document on
Environmental Aspects
Annex O (normative) - Seals of elastomer, cork and
synthetic fibre mixtures
Annex ZA (informative) - Relationship between this
European Standard and the Essential Requirements
of EU Directive 2009/142/EC relating to
appliances burning gaseous fuels
Annex ZB (informative) - Relationship between this
European Standard and the Essential Requirements
of EU Directive 97/23/EC concerning pressure
equipment
Bibliography
BS EN 13611
| Committee |
GSE/22
|
| DocumentType |
Draft
|
| Pages |
151
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| PREN 13611 : DRAFT 2017 | Identical |
| EN 61508-6:2010 | Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 6: Guidelines on the application of IEC 61508-2 and IEC 61508-3 |
| EN 60730-2-14:1997/A2:2008 | AUTOMATIC ELECTRICAL CONTROLS FOR HOUSEHOLD AND SIMILAR USE - PART 2-14: PARTICULAR REQUIREMENTS FOR ELECTRIC ACTUATORS |
| PREN 16340 : DRAFT 2011 | COMBUSTION PRODUCT SENSING DEVICES FOR GAS BURNERS AND GAS BURNING APPLIANCES |
| EN 10293:2015 | Steel castings - Steel castings for general engineering uses |
| ISO 898-2:2012 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 2: Nuts with specified property classes — Coarse thread and fine pitch thread |
| EN 61508-3:2010 | Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 3: Software requirements |
| IEC 60335-2-102:2004+AMD1:2008+AMD2:2012 CSV | Household and similar electrical appliances - Safety - Part 2-102:Particular requirements for gas, oil and solid-fuel burning appliances having electrical connections |
| ISO 9606-4:1999 | Approval testing of welders — Fusion welding — Part 4: Nickel and nickel alloys |
| ISO 7005-2:1988 | Metallic flanges — Part 2: Cast iron flanges |
| EN 60747-5-2:2001/A1:2002 | DISCRETE SEMICONDUCTOR DEVICES AND INTEGRATED CIRCUITS - PART 5-2: OPTOELECTRONIC DEVICES - ESSENTIAL RATINGS AND CHARACTERISTICS |
| EN 61558-2-16:2009/A1:2013 | SAFETY OF TRANSFORMERS, REACTORS, POWER SUPPLY UNITS AND SIMILAR PRODUCTS FOR SUPPLY VOLTAGES UP TO 1 100 V - PART 2-16: PARTICULAR REQUIREMENTS AND TESTS FOR SWITCH MODE POWER SUPPLY UNITS AND TRANSFORMERS FOR SWITCH MODE POWER SUPPLY UNITS (IEC 61558-2-16:2009/A1:2013) |
| ISO 9606-2:2004 | Qualification test of welders — Fusion welding — Part 2: Aluminium and aluminium alloys |
| IEC 60384-14:2013+AMD1:2016 CSV | Fixed capacitors for use in electronic equipment - Part 14: Sectional specification - Fixed capacitors for electromagnetic interference suppression and connection to the supply mains |
| ISO 8434-1:2007 | Metallic tube connections for fluid power and general use Part 1: 24 degree cone connectors |
| ISO 274:1975 | Copper tubes of circular section — Dimensions |
| IEC 60191-1:2007 | Mechanical standardization of semiconductor devices - Part 1: General rules for the preparation of outline drawings of discrete devices |
| ISO 3506-1:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners Part 1: Bolts, screws and studs |
| EN 61508-1:2010 | Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 1: General requirements |
| EN 10226-2:2005 | Pipe threads where pressure tight joints are made on the threads - Part 2: Taper external threads and taper internal threads - Dimensions, tolerances and designation |
| EN 746-2:2010 | Industrial thermoprocessing equipment - Part 2: Safety requirements for combustion and fuel handling systems |
| EN 60730-2-6:2016 | Automatic electrical controls - Part 2-6: Particular requirements for automatic electrical pressure sensing controls including mechanical requirements |
| EN 10216-5:2013 | Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 5: Stainless steel tubes |
| ISO 7637-3:2016 | Road vehicles — Electrical disturbances from conduction and coupling — Part 3: Electrical transient transmission by capacitive and inductive coupling via lines other than supply lines |
| EN 10213:2007+A1:2016 | Steel castings for pressure purposes |
| EN ISO 15613:2004 | Specification and qualification of welding procedures for metallic materials - Qualification based on pre-production welding test (ISO 15613:2004) |
| EN 10028-3:2017 | Flat products made of steels for pressure purposes - Part 3: Weldable fine grain steels, normalized |
| ISO 15614-2:2005 | Specification and qualification of welding procedures for metallic materials Welding procedure test Part 2: Arc welding of aluminium and its alloys |
| EN 13906-1:2013 | Cylindrical helical springs made from round wire and bar - Calculation and design - Part 1 : Compression springs |
| EN 61508-7:2010 | Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 7: Overview of techniques and measures |
| EN 12067-2:2004 | Gas/air ratio controls for gas burners and gas burning appliances - Part 2: Electronic types |
| EN ISO 3506-1:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners - Part 1: Bolts, screws and studs (ISO 3506-1:2009) |
| EN 1057:2006+A1:2010 | Copper and copper alloys - Seamless, round copper tubes for water and gas in sanitary and heating applications |
| EN ISO 15612:2004 | Specification and qualification of welding procedures for metallic materials - Qualification by adoption of a standard welding procedure (ISO 15612:2004) |
| ISO 15610:2003 | Specification and qualification of welding procedures for metallic materials — Qualification based on tested welding consumables |
| EN ISO 3506-3:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners - Part 3: Set screws and similar fasteners not under tensile stress (ISO 3506-3:2009) |
| EN 1643:2014 | Safety and control devices for gas burners and gas burning appliances - Valve proving systems for automatic shut-off valves |
| ISO 23529:2016 | Rubber General procedures for preparing and conditioning test pieces for physical test methods |
| ASTM F 593 : 2017 : REDLINE | Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs |
| EN 485-2:2016 | Aluminium and aluminium alloys - Sheet, strip and plate - Part 2: Mechanical properties |
| ISO 815-1:2014 | Rubber, vulcanized or thermoplastic Determination of compression set Part 1: At ambient or elevated temperatures |
| EN 10028-6:2017 | Flat products made of steels for pressure purposes - Part 6: Weldable fine grain steels, quenched and tempered |
| IEC 61000-4-11:2004+AMD1:2017 CSV | Electromagnetic compatibility (EMC) - Part 4-11: Testing and measurement techniques - Voltage dips, short interruptions and voltage variations immunity tests |
| EN 60127-1:2006/A2:2015 | MINIATURE FUSES - PART 1: DEFINITIONS FOR MINIATURE FUSES AND GENERAL REQUIREMENTS FOR MINIATURE FUSE-LINKS |
| ISO 1083:2004 | Spheroidal graphite cast irons - Classification |
| ASTM A 395/A395M : 1999 | Standard Specification for Ferritic Ductile Iron Pressure-Retaining Castings for Use at Elevated Temperatures |
| SAE J429_201405 | Mechanical and Material Requirements for Externally Threaded Fasteners |
| ASTM A 694/A694M : 2016 : REDLINE | Standard Specification for Carbon and Alloy Steel Forgings for Pipe Flanges, Fittings, Valves, and Parts for High-Pressure Transmission Service |
| EN 10088-3:2014 | Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes |
| ISO 7637-2:2011 | Road vehicles Electrical disturbances from conduction and coupling Part 2: Electrical transient conduction along supply lines only |
| EN 10111:2008 | Continuously hot rolled low carbon steel sheet and strip for cold forming - Technical delivery conditions |
| EN 10087:1998 | Free-cutting steels - Technical delivery conditions for semi-finished products, hot-rolled bars and rods |
| ASTM A 516/A516M : 2017 : REDLINE | Standard Specification for Pressure Vessel Plates, Carbon Steel, for Moderate- and Lower-Temperature Service |
| IEC 61558-2-16:2009+AMD1:2013 CSV | Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-16: Particularrequirements and tests for switch mode power supply units andtransformers for switch mode power supply units |
| ISO 7005-3:1988 | Metallic flanges Part 3: Copper alloy and composite flanges |
| EN 586-2:1994 | Aluminium and aluminium alloys - Forgings - Part 2: Mechanical properties and additional property requirements |
| ASTM A 707/A707M : 2014 : REDLINE | Standard Specification for Forged Carbon and Alloy Steel Flanges for Low-Temperature Service |
| ASTM B 584 : 2014 : REDLINE | Standard Specification for Copper Alloy Sand Castings for General Applications |
| EN 12516-1:2014 | Industrial valves - Shell design strength - Part 1: Tabulation method for steel valve shells |
| EN 61000-4-2:2009 | Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity test |
| EN ISO 9606-4:1999 | Approval testing of welders - Fusion welding - Part 4: Nickel and nickel alloys (ISO 9606-4:1999) |
| IEC 61508-4:2010 | Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 4: Definitions and abbreviations (see Functional Safety and IEC 61508) |
| EN 88-2:2007 | Pressure regulators and associated safety devices for gas appliances - Part 2: Pressure regulators for inlet pressures above 500 mbar up to and including 5 bar |
| IEC 61810-1:2015 | Electromechanical elementary relays - Part 1: General and safety requirements |
| IEC 61508-3:2010 | Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 3: Software requirements (see Functional Safety and IEC 61508) |
| ISO 6708:1995 | Pipework components Definition and selection of DN (nominal size) |
| EN 20898-2 : 1993 | MECHANICAL PROPERTIES OF FASTENERS - PART 2: NUTS WITH SPECIFIED PROOF LOAD VALUES - COARSE THREAD (ISO 898-2:1992) |
| EN 10025-1:2004 | Hot rolled products of structural steels - Part 1: General technical delivery conditions |
| IEC 60127-1:2006+AMD1:2011+AMD2:2015 CSV | Miniature fuses - Part 1: Definitions for miniature fuses andgeneral requirements for miniature fuse-links |
| IEC 60747-5-2:1997+AMD1:2002 CSV | Discrete semiconductor devices and integrated circuits - Part 5-2: Optoelectronic devices - Essential ratings and characteristics |
| EN 161:2011+A3:2013 | Automatic shut-off valves for gas burners and gas appliances |
| EN 473:2008 | Non-destructive testing - Qualification and certification of NDT personnel - General principles |
| API 5L : 2012 | LINE PIPE |
| EN 60947-1:2007/A2:2014 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 1: GENERAL RULES (IEC 60947-1:2007/A2:2014) |
| IEC 60730-2-14:2017 | Automatic electrical controls - Part 2-14: Particular requirements for electric actuators |
| EN 10277-3:2008 | Bright steel products - Technical delivery conditions - Part 3: Free-cutting steels |
| EN 10028-2:2017 | Flat products made of steels for pressure purposes - Part 2: Non-alloy and alloy steels with specified elevated temperature properties |
| EN 10305-1:2016 | Steel tubes for precision applications - Technical delivery conditions - Part 1: Seamless cold drawn tubes |
| EN 10028-7:2016 | Flat products made of steels for pressure purposes - Part 7: Stainless steels |
| ISO 23553-1:2014 | Safety and control devices for oil burners and oil-burning appliances Particular requirements Part 1: Automatic and semi-automatic valves |
| ISO 15612:2004 | Specification and qualification of welding procedures for metallic materials Qualification by adoption of a standard welding procedure |
| EN 10326:2004 | Continuously hot-dip coated strip and sheet of structural steels - Technical delivery conditions |
| EN 1774:1997 | Zinc and zinc alloys - Alloys for foundry purposes - Ingot and liquid |
| EN 61000-4-3 : 2006 AMD 2 2010 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-3: TESTING AND MEASUREMENT TECHNIQUES - RADIATED, RADIO-FREQUENCY, ELECTROMAGNETIC FIELD IMMUNITY TEST |
| EN ISO 15611:2003 | Specification and qualification of welding procedures for metallic materials - Qualification based on previous welding experience (ISO 15611:2003) |
| EN 1854:2010 | Pressure sensing devices for gas burners and gas burning appliances |
| EN ISO 228-1:2003 | Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000) |
| ASTM A 420/A420M : 2016 : REDLINE | Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Low-Temperature Service |
| ISO 15614-1:2017 | Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys |
| ISO 3506-3:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners Part 3: Set screws and similar fasteners not under tensile stress |
| EN 10305-4:2016 | Steel tubes for precision applications - Technical delivery conditions - Part 4: Seamless cold drawn tubes for hydraulic and pneumatic power systems |
| EN 13906-2:2013 | Cylindrical helical springs made from round wire and bar - Calculation and design - Part 2: Extension springs |
| EN 13445-4 : 2014 COR 2017 | UNFIRED PRESSURE VESSELS - PART 4: FABRICATION |
| ISO 262:1998 | ISO general purpose metric screw threads — Selected sizes for screws, bolts and nuts |
| EN 14459:2015 | Safety and control devices for burners and appliances burning gaseous or liquid fuels - Control functions in electronic systems - Methods for classification and assessment |
| EN 61508-2:2010 | Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 2: Requirements for electrical/electronic/programmable electronic safety-related systems |
| EN 10272:2016 | Stainless steel bars for pressure purposes |
| ISO/IEC Guide 51:2014 | Safety aspects — Guidelines for their inclusion in standards |
| EN 10028-5:2017 | Flat products made of steels for pressure purposes - Part 5: Weldable fine grain steels, thermomechanically rolled |
| ISO 15609-1:2004 | Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 1: Arc welding |
| EN ISO 17637:2016 | Non-destructive testing of welds - Visual testing of fusion-welded joints (ISO 17637:2016) |
| PREN 16304 : DRAFT 2011 | VENT VALVES |
| ISO 15611:2003 | Specification and qualification of welding procedures for metallic materials — Qualification based on previous welding experience |
| EN 437:2003+A1:2009 | Test gases - Test pressures - Appliance categories |
| EN 125:2010+A1:2015 | Flame supervision devices for gas burning appliances - Thermoelectric flame supervision devices |
| EN 60730-2-8:2002/A1:2003 | AUTOMATIC ELECTRICAL CONTROLS FOR HOUSEHOLD AND SIMILAR USE - PART 2-8: PARTICULAR REQUIREMENTS FOR ELECTRICALLY OPERATED WIRE VALVES, INCLUDING MECHANICAL REQUIREMENTS |
| EN 1706:2010 | Aluminium and aluminium alloys - Castings - Chemical composition and mechanical properties |
| EN 10222-5:2017 | Steel forgings for pressure purposes - Part 5: Martensitic, austenitic and austenitic-ferritic stainless steels |
| EN 10250-4:1999 | Open die steel forgings for general engineering purposes - Part 4: Stainless steels |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| EN 126:2012 | Multifunctional controls for gas burning appliances |
| IEC 60730-2-8:2000+AMD1:2002+AMD2:2015 CSV | Automatic electrical controls for household and similar use - Part 2-8: Particular requirements for electrically operated watervalves, including mechanical requirements |
| EN ISO 15614-2:2005 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 2: Arc welding of aluminium and its alloys (ISO 15614-2:2005) |
| EN 10250-1:1999 | Open die steel forgings for general engineering purposes - Part 1: General requirements |
| EN 61000-4-8:2010 | Electromagnetic compatibility (EMC) - Part 4-8: Testing and measurement techniques - Power frequency magnetic field immunity test |
| IEC 60947-1:2007+AMD1:2010+AMD2:2014 CSV | Low-voltage switchgear and controlgear - Part 1: General rules |
| EN ISO 9606-2:2004 | Qualification test of welders - Fusion welding - Part 2: Aluminium and aluminium alloys (ISO 9606-2:2004) |
| EN 1559-1:2011 | Founding - Technical conditions of delivery - Part 1: General |
| ASTM F 36 : 2015 : REDLINE | Standard Test Method for Compressibility and Recovery of Gasket Materials |
| IEC 61000-4-2:2008 | Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity test |
| IEC 61000-4-3:2006+AMD1:2007+AMD2:2010 CSV | Electromagnetic compatibility (EMC) - Part 4-3: Testing and measurement techniques - Radiated, radio-frequency, electromagnetic field immunity test |
| EN 10250-2:1999 | Open die steel forgings for general engineering purposes - Part 2: Non-alloy quality and special steels |
| EN 62061:2005/A2:2015 | SAFETY OF MACHINERY - FUNCTIONAL SAFETY OF SAFETY-RELATED ELECTRICAL, ELECTRONIC AND PROGRAMMABLE ELECTRONIC CONTROL SYSTEMS (IEC 62061:2005/A2:2015) |
| IEC 61643-11:2011 | Low-voltage surge protective devices - Part 11: Surge protective devices connected to low-voltage power systems - Requirements and test methods |
| ISO 13849-2:2012 | Safety of machinery — Safety-related parts of control systems — Part 2: Validation |
| ASTM A 217/A217M : 2014 : REDLINE | Standard Specification for Steel Castings, Martensitic Stainless and Alloy, for Pressure-Containing Parts, Suitable for High-Temperature Service |
| EN 60335-2-102:2016 | Household and similar electrical appliances - Safety - Part 2-102: Particular requirements for gas, oil and solid-fuel burning appliances having electrical connections |
| ISO 17637:2016 | Non-destructive testing of welds Visual testing of fusion-welded joints |
| EN 1563:2011 | Founding - Spheroidal graphite cast irons |
| EN ISO 15609-1:2004 | Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 1: Arc welding (ISO 15609-1:2004) |
| EN 12164:2016 | Copper and copper alloys - Rod for free machining purposes |
| EN 10130:2006 | Cold rolled low carbon steel flat products for cold forming - Technical delivery conditions |
| ASTM A 105/A105M : 2014-11 | SPECIFICATION FOR CARBON STEEL FORGINGS FOR PIPING APPLICATIONS |
| EN ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread (ISO 898-1:2013) |
| EN 10083-1:2006 | Steels for quenching and tempering - Part 1: General technical delivery conditions |
| EN ISO 13849-2:2012 | Safety of machinery - Safety-related parts of control systems - Part 2: Validation (ISO 13849-2:2012) |
| EN 10083-2:2006 | Steels for quenching and tempering - Part 2: Technical delivery conditions for non alloy steels |
| EN 60068-2-6:2008 | Environmental testing - Part 2-6: Tests - Test Fc: Vibration (sinusoidal) |
| ISO 9000:2015 | Quality management systems — Fundamentals and vocabulary |
| MSS SP 55 : 2011 | QUALITY STANDARD FOR STEEL CASTINGS FOR VALVES, FLANGES, FITTINGS, AND OTHER PIPING COMPONENTS - VISUAL METHOD FOR EVALUATION OF SURFACE IRREGULARITIES |
| ISO 12100-1:2003 | Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology |
| EN ISO 13849-1:2015 | Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015) |
| EN 61000-4-4:2012 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-4: TESTING AND MEASUREMENT TECHNIQUES - ELECTRICAL FAST TRANSIENT/BURST IMMUNITY TEST (IEC 61000-4-4:2012) |
| CISPR 11:2015 RLV | Industrial, scientific and medical equipment - Radio-frequency disturbance characteristics - Limits and methods of measurement |
| EN 754-2:2016 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 2: Mechanical properties |
| IEC 61508-6:2010 | Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 6: Guidelines on the application of IEC 61508-2 and IEC 61508-3 (see Functional Safety and IEC 61508) |
| EN 61558-2-6:2009 | Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-6: Particular requirements and tests for safety isolating transformers and power supply units incorporating safety isolating transformers |
| EN 60335-1:2012/A13:2017 | HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60335-1:2010, MODIFIED) |
| ISO 37:2017 | Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties |
| EN 10297-1:2003 | Seamless circular steel tubes for mechanical and general engineering purposes - Technical delivery conditions - Part 1: Non-alloy and alloy steel tubes |
| EN 298:2012 | Automatic burner control systems for burners and appliances burning gaseous or liquid fuels |
| EN 10216-1:2013 | Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 1: Non-alloy steel tubes with specified room temperature properties |
| ISO 7005-1:2011 | Pipe flanges — Part 1: Steel flanges for industrial and general service piping systems |
| EN 61000-4-6:2014/AC:2015 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-6: TESTING AND MEASUREMENT TECHNIQUES - IMMUNITY TO CONDUCTED DISTURBANCES, INDUCED BY RADIO-FREQUENCY FIELDS (IEC 61000-4-6:2013) |
| IEC 61508-1:2010 | Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 1: General requirements (see Functional Safety and IEC 61508) |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| ISO 15613:2004 | Specification and qualification of welding procedures for metallic materials Qualification based on pre-production welding test |
| IEC 62061:2005+AMD1:2012+AMD2:2015 CSV | Safety of machinery - Functional safety of safety-related electrical, electronic and programmable electronic control systems |
| EN 549:1994 | Rubber materials for seals and diaphragms for gas appliances and gas equipment |
| ASTM A 312/A312M : 2017-03 | SPECIFICATION FOR SEAMLESS, WELDED, AND HEAVILY COLD WORKED AUSTENITIC STAINLESS STEEL PIPES |
| EN 1106:2010 | Manually operated taps for gas burning appliances |
| IEC 61508-7:2010 | Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 7: Overview of techniques and measures (see Functional Safety and IEC 61508) |
| EN ISO 15610:2003 | Specification and qualification of welding procedures for metallic materials - Qualification based on tested welding consumables (ISO 15610:2003) |
| ISO 15607:2003 | Specification and qualification of welding procedures for metallic materials General rules |
| DIN 52913:2002-04 | TESTING OF STATIC GASKETS FOR FLANGE CONNECTIONS - COMPRESSION CREEP TESTING OF GASKETS MADE FROM SHEETS |
| EN 12165:2016 | Copper and copper alloys - Wrought and unwrought forging stock |
| ISO 301:2006 | Zinc alloy ingots intended for castings |
| IEC 61000-4-29:2000 | Electromagnetic compatibility (EMC) - Part 4-29: Testing and measurement techniques - Voltage dips, short interruptions and voltage variations on d.c. input power port immunity tests |
| EN 1418:1997 | Welding personnel - Approval testing of welding operators for fusion welding and resistance weld setters for fully mechanized and automatic welding of metallic materials |
| EN ISO 23553-1:2014 | Safety and control devices for oil burners and oil-burning appliances - Particular requirements - Part 1: Automatic and semi-automatic valves (ISO 23553-1:2014) |
| ISO 3506-2:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners Part 2: Nuts |
| EN 10028-4:2017 | Flat products made of steels for pressure purposes - Part 4: Nickel alloy steels with specified low temperature properties |
| EN 10226-1:2004 | Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation |
| ISO 13849-1:2015 | Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design |
| IEC 61508-2:2010 | Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 2: Requirements for electrical/electronic/programmable electronic safety-related systems (see Functional Safety and IEC 61508) |
| EN 61000-4-13:2002/A2:2016 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-13: TESTING AND MEASUREMENT TECHNIQUES - HARMONICS AND INTERHARMONICS INCLUDING MAINS SIGNALLING AT A.C. POWER PORT, LOW FREQUENCY IMMUNITY TESTS (IEC 61000-4-13:2002/A2:2015) |
| EN 1982:2017 | Copper and copper alloys - Ingots and castings |
| EN 88-1:2011+A1:2016 | Pressure regulators and associated safety devices for gas appliances - Part 1: Pressure regulators for inlet pressures up to and including 50 kPa |
| DIN 28091-1:2014-11 | TECHNICAL DELIVERY CONDITIONS FOR GASKET SHEETS - PART 1: GENERAL REQUIREMENTS FOR GASKET MATERIALS |
| ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation |
| IEC 61000-4-13:2002+AMD1:2009+AMD2:2015 CSV | Electromagnetic compatibility (EMC) - Part 4-13: Testing and measurement techniques - Harmonics and interharmonics includingmains signalling at a.c. power port, low frequency immunity tests |
| EN ISO 9000:2015 | Quality management systems - Fundamentals and vocabulary (ISO 9000:2015) |
| EN 61000-4-10:2017 | Electromagnetic compatibility (EMC) - Part 4-10: Testing and measurement techniques - Damped oscillatory magnetic field immunity test |
| IEC 60384-16:2005 | Fixed capacitors for use in electronic equipment - Part 16: Sectional specification: Fixed metallized polypropylene film dielectric d.c. capacitors |
| EN 755-2:2016 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 2: Mechanical properties |
| EN 61000-4-29:2000 | Electromagnetic compatibility (EMC) - Part 4-29: Testing and measurement techniques - Voltage dips, short interruptions and voltage variations on d.c. input power port immunity tests |
| EN ISO 15607:2003 | Specification and qualification of welding procedures for metallic materials - General rules (ISO 15607:2003) |
| EN ISO 9606-3:1999 | Approval testing of welders - Fusion welding - Part 3: Copper and copper alloys (ISO 9606-3:1999) |
| EN 50159:2010 | Railway applications - Communication, signalling and processing systems - Safety-related communication in transmission systems |
| EN 10255:2004+A1:2007 | Non-Alloy steel tubes suitable for welding and threading - Technical delivery conditions |
| EN 60730-1:2016 | Automatic electrical controls - Part 1: General requirements |
| EN 13555:2014 | Flanges and their joints - Gasket parameters and test procedures relevant to the design rules for gasketed circular flange connections |
| ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread |
| EN 10222-1:2017 | Steel forgings for pressure purposes - Part 1: General requirements for open die forgings |
| ISO 1817:2015 | Rubber, vulcanized or thermoplastic Determination of the effect of liquids |
| EN 10088-1:2014 | Stainless steels - Part 1: List of stainless steels |
| EN 61508-4:2010 | Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 4: Definitions and abbreviations |
| ISO 9606-3:1999 | Approval testing of welders — Fusion welding — Part 3: Copper and copper alloys |
| SAE J995_201202 | Mechanical and Material Requirements for Steel Nuts |
| IEC 60730-1:2013+AMD1:2015 CSV | Automatic electrical controls - Part 1: General requirements |
| EN ISO 3506-2:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners - Part 2: Nuts (ISO 3506-2:2009) |
| EN 287-1:2011 | Qualification test of welders - Fusion welding - Part 1: Steels |
| EN 12186:2014 | Gas infrastructure - Gas pressure regulating stations for transmission and distribution - Functional requirements |
| EN 257:2010 | Mechanical thermostats for gas-burning appliances |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.