EN 574:1996+A1:2008
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Safety of machinery - Two-hand control devices - Functional aspects - Principles for design
Superseded date
24-03-2022
Superseded by
Published date
25-06-2008
Publisher
Sorry this product is not available in your region.
Foreword
Introduction
1 Scope
2 Normative references
3 Definitions
4 Types of two-hand control devices and their selection
5 Characteristics of safety functions
6 Requirements related to categories of control
7 Use of programmable electronic systems
8 Prevention of accidental actuation and of defeat
9 General requirements
10 Verification
11 Marking
12 Information for installation, use and maintenance
Annex A (normative) Measurement tests for the prevention of defeat
Annex B (informative) Use of categories (according to EN
954-1:1996) in types of two-hand control devices
Annex ZA (informative) Relationship between this European
Standard and the Essential Requirements of EU
Directive 98/37/EC
Annex ZB (informative) Relationship between this European
Standard and the Essential Requirements of EU
Directive 2006/42/EC
Bibliography
This standard specifies the safety requirements of a two-hand control device and its logic unit as defined in3.1.This standard describes the main characteristics of two-hand control devices for the achievement of safetyand sets out combinations of functional characteristics for three types. This standard does not apply todevices intended to be used as enabling devices, hold to run devices and as special control devices.This standard does not specify with which machines two-hand control devices shall be used. It also does notspecify which types of two-hand-control device shall be used. Moreover it does not specify the distancebetween the two-hand control device and the danger zone (see 9.8).The standard provides requirements and guidance on the design and selection (based on a risk assessment)of two-hand control devices including their assessment, the prevention of defeat and the avoidance of faults.The standard also provides requirements and guidance for two-hand control devices containing aprogrammable electronic system (see 7).This standard applies to all two-hand control devices, independent of the energy used, including:- Two-hand control devices which are or are not integral parts of a machine;- Two-hand control devices which consist of one or more than one separate elements.
| Committee |
CEN/TC 114
|
| DevelopmentNote |
1996 Edition Re-Issued in June 2008 & incorporates AMD 1 2008. (07/2008)
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| NS EN 574 : 1996 + A1 2008 | Identical |
| NEN EN 574 : 1997 + A1 2008 | Identical |
| UNI EN 574 : 2008 | Identical |
| BS EN 574 : 1997 | Identical |
| NBN EN 574 : 1997 + A1 2008 | Identical |
| BS EN 574 : 1996 | Identical |
| UNE-EN 574:1997 | Identical |
| NF EN 574 : 1997 + A1 2008 | Identical |
| I.S. EN 574:1997 | Identical |
| PN EN 574 : 1999 + A1 2010 | Identical |
| SN EN 574 : 1997 + A1 2008 | Identical |
| UNE-EN 574:1997+A1:2008 | Identical |
| BS EN 574:1996+A1:2008 | Identical |
| DIN EN 574:2008-12 | Identical |
| 12/30255086 DC : 0 | BS EN 289 - PLASTICS AND RUBBER MACHINES - COMPRESSION MOULDING MACHINES AND TRANSFER MOULDING MACHINES - SAFETY REQUIREMENTS |
| UNE-EN 1501-5:2012 | Refuse collection vehicles - General requirements and safety requirements - Part 5: Lifting devices for refuse collection vehicles |
| I.S. EN ISO 12100-2:2003 | SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 2: TECHNICAL PRINCIPLES |
| I.S. EN 12415:2000 | SAFETY OF MACHINE TOOLS - SMALL NUMERICALLY CONTROLLED TURNING MACHINES AND TURNING CENTRES |
| BS EN 415-8:2008 | Safety of packaging machines Strapping machines |
| 02/711111 DC : DRAFT SEP 2002 | PREN 415-7 - PACKAGING MACHINES SAFETY - PART 7: GROUP AND SECONDARY PACKAGING MACHINES |
| 03/119040 DC : DRAFT NOV 2003 | PREN 1010-1 - SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PRINTING AND PAPER CONVERTING MACHINES - PART 1: COMMON REQUIREMENTS |
| 11/30251974 DC : 0 | BS EN 15180 - FOOD PROCESSING MACHINERY - FOOD DEPOSITORS - SAFETY AND HYGIENE REQUIREMENTS |
| 05/30131998 DC : 0 | BS EN 15180 - FOOD PROCESSING MACHINERY - FORMING MACHINES - SAFETY AND HYGIENE REQUIREMENTS |
| 10/30232422 DC : DRAFT DEC 2010 | BS EN 1870-9 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 9: DOUBLE BLADE CIRCULAR SAWING MACHINES FOR CROSS-CUTTING WITH INTEGRATED FEED AND WITH MANUAL LOADING AND/OR UNLOADING |
| PREN 1870-3 : DRAFT 2012 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 3: DOWN CUTTING CROSS-CUT SAWS AND DUAL PURPOSE DOWN CUTTING CROSS-CUT SAWS/CIRCULAR SAW BENCHES |
| I.S. EN 13128:2001 | SAFETY OF MACHINE TOOLS - MILLING MACHINES (INCLUDING BORING MACHINES) |
| I.S. EN 14070:2003 | SAFETY OF MACHINE TOOLS - TRANSFER AND SPECIAL-PURPOSE MACHINES |
| 05/30130669 DC : DRAFT MAR 2005 | BS EN 15165 - FOOD PROCESSING MACHINERY - FORMING MACHINES - SAFETY AND HYGIENE REQUIREMENTS |
| 12/30243084 DC : 0 | BS EN 1034-21 - SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 21: COATING MACHINES |
| BS EN 15180:2014 | Food processing machinery. Food depositors. Safety and hygiene requirements |
| BS EN 14753:2007 | Safety of machinery. Safety requirements for machinery and equipment for continuous casting of steel |
| 04/30126149 DC : 0 | EN 528 - RAIL DEPENDENT STORAGE AND RETRIEVAL EQUIPMENT - SAFETY |
| PREN 15572 : DRAFT 2013 | MACHINES AND PLANTS FOR MINING AND TOOLING OF NATURAL STONE - SAFETY - REQUIREMENTS FOR EDGE FINISHING MACHINES |
| I.S. EN 14753:2007 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR MACHINERY AND EQUIPMENT FOR CONTINUOUS CASTING OF STEEL |
| DIN EN 16486:2014-10 | MACHINES FOR COMPACTING WASTE MATERIALS OR RECYCLABLE FRACTIONS - COMPACTORS - SAFETY REQUIREMENTS |
| I.S. EN 12649:2008 | CONCRETE COMPACTORS AND SMOOTHING MACHINES - SAFETY |
| PREN 1870-12 : DRAFT 2011 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 12: PENDULUM CROSS-CUT SAWING MACHINES |
| I.S. EN 16500:2014 | MACHINES FOR COMPACTING WASTE MATERIALS OR RECYCLABLE FRACTIONS - VERTICAL BALING PRESSES - SAFETY REQUIREMENTS |
| UNI EN 15180 : 2014 | FOOD PROCESSING MACHINERY - FOOD DEPOSITORS - SAFETY AND HYGIENE REQUIREMENTS |
| UNE-EN 16500:2015 | Machines for compacting waste materials or recyclable fractions - Vertical baling presses - Safety requirements |
| 16/30314039 DC : 0 | BS EN 12301 - PLASTICS AND RUBBER MACHINES - CALENDERS - SAFETY REQUIREMENTS |
| UNI EN 1034-21 : 2012 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 21: COATING MACHINES |
| EN 12013:2018 | Plastics and rubber machines - Internal mixers - Safety requirements |
| I.S. EN 1114-3:2001 | RUBBER AND PLASTICS MACHINES - EXTRUDERS AND EXTRUSION LINES - PART 3: SAFETY REQUIREMENTS FOR HAUL-OFFS |
| DIN EN 12409:2011-12 | Plastics and rubber machines - Thermoforming machines - Safety requirements |
| DIN EN 609-1:2010-07 | AGRICULTURAL AND FORESTRY MACHINERY - SAFETY OF LOG SPLITTERS - PART 1: WEDGE SPLITTERS |
| DIN EN 415-7:2009-12 | Safety of packaging machines - Part 7: Group and secondary packaging machines (includes Amendment A1:2008) |
| DIN EN 13288:2010-10 | Food processing machinery - Bowl lifting and tilting machines - Safety and hygiene requirements (includes Amendment A1:2009) |
| DIN EN 415-5:2010-04 | Safety of packaging machines - Part 5: Wrapping machines (includes Amendment A1:2009) |
| DIN EN 13355:2010-06 | COATING PLANTS - COMBINED BOOTHS - SAFETY REQUIREMENTS |
| DIN EN 1870-12:2014-03 | Safety of woodworking machines - Circular sawing machines - Part 12: Pendulum cross-cut sawing machines |
| DIN EN 1034-14:2010-07 | Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 14: Reel splitter (includes Amendment A1:2009) |
| DIN EN 1870-16:2013-01 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 16: DOUBLE MITRE SAWING MACHINES FOR V CUTTING |
| DIN EN 13591:2010-10 | Food processing machinery - Fixed deck oven loaders - Safety and hygiene requirements (includes Amendment A1:2009) |
| DIN EN 1756-2:2009-12 | Tail lifts - Platform lifts for mounting on wheeled vehicles - Safety requirements - Part 2: Tail lifts for passengers (includes Amendment A1:2009) |
| DIN EN 12653:2010-06 | Footwear, leather and imitation leather manufacturing machines - Nailing machines - Safety requirements (includes Amendment A2:2009) |
| DIN EN 1870-9:2013-01 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 9: DOUBLE BLADE CIRCULAR SAWING MACHINES FOR CROSS-CUTTING WITH INTEGRATED FEED AND WITH MANUAL LOADING AND/OR UNLOADING |
| DIN EN 792-7:2009-12 | HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 7: GRINDERS |
| DIN EN 13389:2010-10 | Food processing machinery - Mixers with horizontal shafts - Safety and hygiene requirements (includes Amendment A1:2009) |
| DIN EN 1870-3:2015-02 | Safety of woodworking machines - Circular sawing machines - Part 3: Down cutting cross-cut saws and dual purpose down cutting cross-cut saws/circular saw benches |
| BS EN 12203 : 2003 | FOOTWEAR, LEATHER AND IMITATION LEATHER GOODS MANUFACTURING MACHINES - SHOE AND LEATHER PRESSES - SAFETY REQUIREMENTS |
| BS EN 710 : 1998 | SAFETY REQUIREMENTS FOR FOUNDRY MOULDING AND COREMAKING MACHINERY AND PLANT AND ASSOCIATED EQUIPMENT |
| BS EN 894-3 : 2000 | SAFETY OF MACHINERY - ERGONOMICS REQUIREMENTS FOR THE DESIGN OF DISPLAYS AND CONTROL ACTUATORS - PART 3: CONTROL ACTUATORS |
| ISO 12100-2:2003 | Safety of machinery Basic concepts, general principles for design Part 2: Technical principles |
| BS EN 792-10 : 2000 | HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 10: COMPRESSION POWER TOOLS |
| BS EN 13128 : 2001 | SAFETY OF MACHINE TOOLS - MILLING MACHINES (INCLUDING BORING MACHINES) |
| BS EN 12984 : 2005 | FOOD PROCESSING MACHINERY - PORTABLE AND/OR HAND-GUIDED MACHINES AND APPLIANCES WITH MECHANICALLY DRIVEN CUTTING TOOLS - SAFETY AND HYGIENE REQUIREMENTS |
| UNE-EN 609-1:2017 | Agricultural and forestry machinery - Safety of log splitters - Part 1: Wedge splitters |
| BS EN 1870-9:2012 | Safety of woodworking machines. Circular sawing machines Double blade circular sawing machines for cross-cutting with integrated feed and with manual loading and/or unloading |
| BS EN 12622 : 2009 | SAFETY OF MACHINE TOOLS - HYDRAULIC PRESS BRAKES |
| BS EN 528:2008 | Rail dependent storage and retrieval equipment. Safety requirements |
| BS EN 12409 : 2008 | PLASTICS AND RUBBER MACHINES - THERMOFORMING MACHINES - SAFETY REQUIREMENTS |
| BS EN 1870-10:2013 | Safety of woodworking machines. Circular sawing machines Single blade automatic and semi-automatic up-cutting cross-cut sawing machines |
| BS EN 15067:2007 | Plastics and rubber machines. Film converting machines for bags and sacks. Safety requirements |
| BS EN 415-6:2013 | Safety of packaging machines Pallet wrapping machines |
| BS EN 12387 : 2005 | FOOTWEAR, LEATHER AND IMITATION LEATHER GOODS MANUFACTURING MACHINES - MODULAR SHOE REPAIR EQUIPMENT - SAFETY REQUIREMENTS |
| EN 12463:2014 | Food processing machinery - Filling machines and auxiliary machines - Safety and hygiene requirements |
| EN 528:2008 | Rail dependent storage and retrieval equipment - Safety requirements |
| I.S. EN 1870-16:2012 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 16: DOUBLE MITRE SAWING MACHINES FOR V-CUTTING |
| I.S. EN 12921-1:2005 | MACHINES FOR SURFACE CLEANING AND PRE-TREATMENT OF INDUSTRIAL ITEMS USING LIQUIDS OR VAPOURS - PART 1: COMMON SAFETY REQUIREMENTS |
| I.S. EN 1501-2:2005 | REFUSE COLLECTION VEHICLES AND ASSOCIATED LIFTING DEVICES - GENERAL REQUIREMENTS AND SAFETY REQUIREMENTS - PART 2: SIDE LOADED REFUSE COLLECTION VEHICLES |
| EN 12203:2003+A1:2009 | Footwear, leather and imitation leather goods manufacturing machines - Shoe and leather presses - Safety requirements |
| DIN EN 15067:2008-03 | Plastics and rubber machines - Film converting machines for bags and sacks - Safety requirements |
| EN 1114-1:2011 | Plastics and rubber machines - Extruders and extrusion lines - Part 1: Safety requirements for extruders |
| EN 1501-5:2011 | Refuse collection vehicles - General requirements and safety requirements - Part 5: Lifting devices for refuse collection vehicles |
| DIN EN 14070:2009-07 | SAFETY OF MACHINE TOOLS - TRANSFER AND SPECIAL-PURPOSE MACHINES |
| EN 1034-5:2005+A1:2009 | Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 5: Sheeters |
| EN 12044:2005+A1:2009 | Footwear, leather and imitation leather goods manufacturing machines - Cutting and punching machines - Safety requirements |
| EN 12653:1999+A2:2009 | Footwear, leather and imitation leather manufacturing machines - Nailing machines - Safety requirements |
| EN 1010-1:2004+A1:2010 | Safety of machinery - Safety requirements for the design and construction of printing and paper converting machines - Part 1: Common requirements |
| DIN EN 1114-3:2010-01 | PLASTICS AND RUBBER MACHINES - EXTRUDERS AND EXTRUSION LINES - PART 3: SAFETY REQUIREMENTS FOR HAUL-OFFS |
| EN 12151:2007 | Machinery and plants for the preparation of concrete and mortar - Safety requirements |
| EN 1501-1:2011+A1:2015 | Refuse collection vehicles - General requirements and safety requirements - Part 1: Rear loaded refuse collection vehicles |
| EN 50191:2010 | ERECTION AND OPERATION OF ELECTRICAL TEST EQUIPMENT |
| EN 1034-21:2012 | Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 21: Coating machines |
| EN 12717:2001+A1:2009 | Safety of machine tools - Drilling machines |
| EN 12621:2006+A1:2010 | Machinery for the supply and circulation of coating materials under pressure - Safety requirements |
| NF EN 201 : 2009 | PLASTICS AND RUBBER MACHINES - INJECTION MOULDING MACHINES - SAFETY REQUIREMENTS |
| EN 12409:2008+A1:2011 | Plastics and rubber machines - Thermoforming machines - Safety requirements |
| UNI EN 12463 : 2014 | FOOD PROCESSING MACHINERY - FILLING MACHINES AND AUXILIARY MACHINES - SAFETY AND HYGIENE REQUIREMENTS |
| DIN EN ISO 12100-2:2004-04 | SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 2: TECHNICAL PRINCIPLES |
| EN 12921-1:2005+A1:2010 | Machines for surface cleaning and pre-treatment of industrial items using liquids or vapours - Part 1: Common safety requirements |
| EN 12215:2004+A1:2009 | Coating plants - Spray booths for application of organic liquid coating materials - Safety requirements |
| EN 12478:2000/AC:2001 | SAFETY OF MACHINE TOOLS - LARGE NUMERICALLY CONTROLLED TURNING MACHINES AND TURNING CENTRES |
| EN 12757-1:2005+A1:2010 | Mixing machinery for coating materials - Safety requirements - Part 1: Mixing machinery for use in vehicle refinishing |
| EN 13355:2004+A1:2009 | Coating plants - Combined booths - Safety requirements |
| EN 12622:2009+A1:2013 | Safety of machine tools - Hydraulic press brakes |
| EN 12649:2008+A1:2011 | Concrete compactors and smoothing machines - Safety |
| DIN EN 999:1998-12 | SAFETY OF MACHINERY - THE POSITIONING OF PROTECTIVE EQUIPMENT IN RESPECT OF APPROACH SPEEDS OF PARTS OF THE HUMAN BODY |
| ONORM EN 1756-1 : 2008 | TAIL LIFTS - PLATFORM LIFTS FOR MOUNTING ON WHEELED VEHICLES - SAFETY REQUIREMENTS - PART 1: TAIL LIFTS FOR GOODS |
| DIN EN 12012-1:2015-05 (Draft) | PLASTICS AND RUBBER MACHINES - SIZE REDUCTION MACHINES - PART 1: SAFETY REQUIREMENTS FOR BLADE GRANULATORS |
| 00/107021 DC : DRAFT OCT 2000 | BS EN 1501-2 - REFUSE COLLECTION VEHICLES AND THEIR ASSOCIATED LIFTING DEVICES - GENERAL REQUIREMENTS AND SAFETY REQUIREMENTS - PART 2: SIDE LOADED REFUSE COLLECTION VEHICLES |
| BS EN 1501-3:2008 | Refuse collection vehicles and their associated lifting devices. General requirements and safety requirements Front loaded refuse collection vehicles |
| I.S. EN 12840:2001 | SAFETY OF MACHINE-TOOLS - MANUALLY CONTROLLED TURNING MACHINES WITH OR WITHOUT AUTOMATIC CONTROL |
| UNI EN 16500 : 2014 | MACHINES FOR COMPACTING WASTE MATERIALS OR RECYCLABLE FRACTIONS - VERTICAL BALING PRESSES - SAFETY REQUIREMENTS |
| PREN 1672-1 : DRAFT 2012 | FOOD PROCESSING MACHINERY - BASIC CONCEPTS - PART 1: SAFETY REQUIREMENTS |
| 06/30156494 DC : 0 | BS EN 15572 - MACHINES AND PLANTS FOR MINING AND TOOLING OF NATURAL STONES - SAFETY - REQUIREMENTS FOR EDGE FINISHING MACHINES |
| 16/30322398 DC : 0 | BS EN 1612 - PLASTICS AND RUBBER MACHINES - REACTION MOULDING MACHINES AND PLANTS - SAFETY REQUIREMENTS |
| 04/30115780 DC : DRAFT JUN 2004 | ISO 9355-3 - SAFETY OF MACHINERY - ERGONOMIC REQUIREMENTS FOR THE DESIGN OF SIGNALS AND CONTROL ACTUATORS - PART 3: CONTROL ACTUATORS |
| DIN EN 15094:2009-04 | Safety of machinery - Safety requirements for cold flat rolling mills |
| 11/30237557 DC : 0 | BS EN 1870-11 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 11: SEMI-AUTOMATIC AND AUTOMATIC HORIZONTAL CROSS-CUT SAWING MACHINES WITH ONE SAW UNIT (RADIAL ARM SAWS) |
| 12/30259421 DC : 0 | BS EN 1672-1 - FOOD PROCESSING MACHINERY - BASIC CONCEPTS - PART 1: SAFETY REQUIREMENTS |
| 05/30138432 DC : DRAFT AUG 2005 | BS EN 1501-1 - REFUSE COLLECTION VEHICLES - GENERAL REQUIREMENTS AND SAFETY REQUIREMENTS - PART 1: REAR LOADED REFUSE COLLECTION VEHICLES |
| I.S. EN 12151:2007 | MACHINERY AND PLANTS FOR THE PREPARATION OF CONCRETE AND MORTAR - SAFETY REQUIREMENTS |
| BS EN ISO 8230-1:2008 | Safety requirements for dry-cleaning machines Common safety requirements |
| PREN 1870-11 : DRAFT 2011 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 11: SEMI-AUTOMATIC AND AUTOMATIC HORIZONTAL CROSS-CUT SAWING MACHINES WITH ONE SAW UNIT (RADIAL ARM SAWS) |
| 12/30259995 DC : 0 | BS EN 12463 - FOOD PROCESSING MACHINERY - FILLING MACHINES AND AUXILIARY MACHINES - SAFETY AND HYGIENE REQUIREMENTS |
| PREN 12012-1 : DRAFT 2015 | PLASTICS AND RUBBER MACHINES - SIZE REDUCTION MACHINES - PART 1: SAFETY REQUIREMENTS FOR BLADE GRANULATORS AND SHREDDERS |
| 04/102838 DC : DRAFT JAN 2004 | EN 692 - MACHINE TOOLS - MECHANICAL PRESSES - SAFETY |
| 12/30270038 DC : 0 | BS EN 16500 - MACHINES FOR COMPACTING WASTE MATERIALS OR RECYCLABLE FRACTIONS - VERTICAL BALING PRESSES - SAFETY REQUIREMENTS |
| 03/118895 DC : 0 | EN 12622 - SAFETY OF MACHINE TOOLS - HYDRAULIC PRESS BRAKES |
| BS EN 16486:2014 | Machines for compacting waste materials or recyclable fractions. Compactors. Safety requirements |
| 13/30276223 DC : 0 | BS EN 15572 - MACHINES AND PLANTS FOR MINING AND TOOLING OF NATURAL STONE - SAFETY - REQUIREMENTS FOR EDGE FINISHING MACHINES |
| 04/30124285 DC : 0 | EN 15059 - SNOW GROOMING EQUIPMENT - SAFETY REQUIREMENTS |
| BS EN 1672-1:2014 | Food processing machinery. Basic concepts Safety requirements |
| I.S. EN 16486:2014 | MACHINES FOR COMPACTING WASTE MATERIALS OR RECYCLABLE FRACTIONS - COMPACTORS - SAFETY REQUIREMENTS |
| UNI EN 16486 : 2014 | MACHINES FOR COMPACTING WASTE MATERIALS OR RECYCLABLE FRACTIONS - COMPACTORS - SAFETY REQUIREMENTS |
| UNI EN 15165 : 2014 | FOOD PROCESSING MACHINERY - FORMING MACHINES - SAFETY AND HYGIENE REQUIREMENTS |
| I.S. EN 15180:2014 | FOOD PROCESSING MACHINERY - FOOD DEPOSITORS - SAFETY AND HYGIENE REQUIREMENTS |
| NF EN 50191 : 2011 | ERECTION AND OPERATION OF ELECTRICAL TEST EQUIPMENT |
| PREN 289 : DRAFT 2012 | PLASTICS AND RUBBER MACHINES - COMPRESSION MOULDING MACHINES AND TRANSFER MOULDING MACHINES - SAFETY REQUIREMENTS |
| UNI EN 12012-1 : 2008 | PLASTICS AND RUBBER MACHINES - SIZE REDUCTION MACHINES - PART 1: SAFETY REQUIREMENTS FOR BLADE GRANULATORS |
| NF EN 1501-2 : 2005 + A1 2010 | REFUSE COLLECTION VEHICLES AND ASSOCIATED LIFTING DEVICES - GENERAL REQUIREMENTS AND SAFETY REQUIREMENTS - PART 2: SIDE LOADED REFUSE COLLECTION VEHICLES |
| DIN EN 1010-1:2011-06 | Safety of machinery - Safety requirements for the design and construction of printing and paper converting machines - Part 1: Common requirements (includes Amendment A1:2010) |
| DIN EN 12215:2010-06 | COATING PLANTS - SPRAY BOOTHS FOR APPLICATION OF ORGANIC LIQUID COATING MATERIALS - SAFETY REQUIREMENTS |
| DIN EN 12387:2010-03 | Footwear, leather and imitation leather goods manufacturing machines - Modular shoe repair equipment - Safety requirements (includes Amendment A1:2009) |
| DIN EN 13128:2009-09 | SAFETY OF MACHINE TOOLS - MILLING MACHINES (INCLUDING BORING MACHINES) |
| DIN EN 12621:2011-07 | Machinery for the supply and circulation of coating materials under pressure - Safety requirements (includes Amendment A1:2010) |
| DIN EN 12984:2011-02 | Food processing machinery - Portable and/or hand-guided machines and appliances with mechanically driven cutting tools - Safety and hygiene requirements (includes Amendment A1:2010) |
| DIN EN 12203:2010-07 | Footwear, leather and imitation leather goods manufacturing machines - Shoe and leather presses - Safety requirements; German version EN 12203:2003+A1:2009 |
| DIN EN 12463:2015-02 | Food processing machinery - Filling machines and auxiliary machines - Safety and hygiene requirements |
| DIN EN 1756-1:2008-10 | Tail lifts - Platform lifts for mounting on wheeled vehicles - Safety requirements - Part 1: Tail lifts for goods (includes Amendment A1:2008) |
| DIN EN 12581:2011-02 | Coating plants - Machinery for dip coating and electrodeposition of organic liquid coating material - Safety requirements (includes Amendment A1:2010) |
| DIN EN 12417:2009-07 | MACHINE TOOLS - SAFETY - MACHINING CENTRES |
| DIN EN 1417:2015-03 | Plastics and rubber machines - Two roll mills - Safety requirements; German version EN 1417:2014 |
| DIN EN 12981:2010-06 | COATING PLANTS - SPRAY BOOTHS FOR APPLICATION OF ORGANIC POWDER COATING MATERIAL - SAFETY REQUIREMENTS |
| DIN EN 1870-10:2013-07 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 10: SINGLE BLADE AUTOMATIC AND SEMI-AUTOMATIC UP-CUTTING CROSS-CUT SAWING MACHINES |
| DIN EN 869:2009-12 | Safety of machinery - Safety requirements for pressure metal diecasting units (includes Amendment A1:2009) |
| DIN EN 693:2011-11 | MACHINE TOOLS - SAFETY - HYDRAULIC PRESSES |
| DIN EN 12044:2010-03 | Footwear, leather and imitation leather goods manufacturing machines - Cutting and punching machines - Safety requirements (includes Amendment A1:2009) |
| BS EN 1501-2 : 2005 | REFUSE COLLECTION VEHICLES AND ASSOCIATED LIFTING DEVICES - GENERAL REQUIREMENTS AND SAFETY REQUIREMENTS - PART 2: SIDE LOADED REFUSE COLLECTION VEHICLES |
| UNE-EN 289:2014 | Plastics and rubber machines - Compression moulding machines and transfer moulding machines - Safety requirements |
| BS EN 12215 : 2004 | COATING PLANTS - SPRAY BOOTHS FOR APPLICATION OF ORGANIC LIQUID COATING MATERIALS - SAFETY REQUIREMENTS |
| BS EN 12981 : 2005 | COATING PLANTS - SPRAY BOOTHS FOR APPLICATION OF ORGANIC POWDER COATING MATERIAL - SAFETY REQUIREMENTS |
| DIN EN 894-3:2010-01 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 3: Control actuators (includes Amendment A1:2008) |
| BS EN 13355 : 2004 | COATING PLANTS - COMBINED BOOTHS - SAFETY REQUIREMENTS |
| BS EN 1034-14 : 2005 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 14: REEL SPLITTER |
| BS EN 12653 : 2000 | FOOTWEAR, LEATHER AND IMITATION LEATHER MANUFACTURING MACHINES - NAILING MACHINES - SAFETY REQUIREMENTS |
| BS EN 12757-1 : 2005 | MIXING MACHINERY FOR COATING MATERIALS - SAFETY REQUIREMENTS - PART 1: MIXING MACHINERY FOR USE IN VEHICLE REFINISHING |
| UNE-EN 1870-10:2013 | Safety of woodworking machines - Circular sawing machines - Part 10: Single blade automatic and semi-automatic up-cutting cross-cut sawing machines |
| BS EN 15095 : 2007 | POWER-OPERATED MOBILE RACKING AND SHELVING, CAROUSELS AND STORAGE LIFTS - SAFETY REQUIREMENTS |
| BS EN 1034-5 : 2005 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 5: SHEETERS |
| BS EN 620 : 2002 | |
| BS EN 12629-6 : 2004 | MACHINES FOR THE MANUFACTURE OF CONSTRUCTIONAL PRODUCTS FROM CONCRETE AND CALCIUM-SILICATE - SAFETY - PART 6: STATIONARY AND MOBILE EQUIPMENT FOR THE MANUFACTURE OF PRECAST REINFORCED PRODUCTS |
| EN 16486:2014 | Machines for compacting waste materials or recyclable fractions - Compactors - Safety requirements |
| I.S. EN 12717:2001 | SAFETY OF MACHINE TOOLS - DRILLING MACHINES |
| DIN EN 1915-1:2001-06 | AIRCRAFT GROUND SUPPORT EQUIPMENT - GENERAL REQUIREMENTS - PART 1: BASIC SAFETY REQUIREMENTS |
| I.S. EN 869:2006 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR PRESSURE METAL DIECASTING UNITS |
| I.S. EN 289:2014 | PLASTICS AND RUBBER MACHINES - COMPRESSION MOULDING MACHINES AND TRANSFER MOULDING MACHINES - SAFETY REQUIREMENTS |
| I.S. EN 12203:2003 | FOOTWEAR, LEATHER AND IMITATION LEATHER GOODS MANUFACTURING MACHINES - SHOE AND LEATHER PRESSES - SAFETY REQUIREMENTS |
| I.S. EN ISO 10472-6:2008 | SAFETY REQUIREMENTS FOR INDUSTRIAL LAUNDRY MACHINERY - PART 6: IRONING AND FUSING PRESSES |
| I.S. EN 415-6:2013 | SAFETY OF PACKAGING MACHINES - PART 6: PALLET WRAPPING MACHINES |
| I.S. EN 1870-10:2013 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 10: SINGLE BLADE AUTOMATIC AND SEMI-AUTOMATIC UP-CUTTING CROSS-CUT SAWING MACHINES |
| I.S. EN 12629-6:2004 | MACHINES FOR THE MANUFACTURE OF CONSTRUCTIONAL PRODUCTS FROM CONCRETE AND CALCIUM-SILICATE - SAFETY - PART 6: STATIONARY AND MOBILE EQUIPMENT FOR THE MANUFACTURE OF PRECAST REINFORCED PRODUCTS |
| I.S. EN 12622:2009 | SAFETY OF MACHINE TOOLS - HYDRAULIC PRESS BRAKES |
| I.S. EN 13885:2005 | FOOD PROCESSING MACHINERY - CLIPPING MACHINES - SAFETY AND HYGIENE REQUIREMENTS |
| I.S. EN 1870-11:2013 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 11: SEMI AUTOMATIC HORIZONTAL CROSS-CUT SAWING MACHINES WITH ONE SAW UNIT (RADIAL ARM SAWS) |
| I.S. EN 12757-1:2005 | MIXING MACHINERY FOR COATING MATERIALS - SAFETY REQUIREMENTS - PART 1: MIXING MACHINERY FOR USE IN VEHICLE REFINISHING |
| I.S. EN 12215:2004 | COATING PLANTS - SPRAY BOOTHS FOR APPLICATION OF ORGANIC LIQUID COATING MATERIALS - SAFETY REQUIREMENTS |
| I.S. EN 13288:2005 | FOOD PROCESSING MACHINERY - BOWL LIFTING AND TILTING MACHINES - SAFETY AND HYGIENE REQUIREMENTS |
| I.S. EN 1870-12:2013 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 12: PENDULUM CROSS-CUT SAWING MACHINES |
| I.S. EN 1870-9:2012 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 9: DOUBLE BLADE CIRCULAR SAWING MACHINES FOR CROSSCUTTING WITH INTEGRATED FEED AND WITH MANUAL LOADING AND/OR UNLOADING |
| I.S. EN 1870-3:2014 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 3: DOWN CUTTING CROSS-CUT SAWS AND DUAL PURPOSE DOWN CUTTING CROSS-CUT SAWS/CIRCULAR SAW BENCHES |
| I.S. EN 15095:2007 | POWER-OPERATED MOBILE RACKING AND SHELVING, CAROUSELS AND STORAGE LIFTS - SAFETY REQUIREMENTS |
| DIN EN 792-7:2002-12 | HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 7: GRINDERS |
| I.S. EN 1915-1:2013 | AIRCRAFT GROUND SUPPORT EQUIPMENT - GENERAL REQUIREMENTS - PART 1: BASIC SAFETY REQUIREMENTS |
| I.S. EN 12409:2008 | PLASTICS AND RUBBER MACHINES - THERMOFORMING MACHINES - SAFETY REQUIREMENTS |
| I.S. EN 12044:2005 | FOOTWEAR, LEATHER AND IMITATION LEATHER GOODS MANUFACTURING MACHINES - CUTTING AND PUNCHING MACHINES - SAFETY REQUIREMENTS |
| I.S. EN 12629-1:2000 | MACHINES FOR THE MANUFACTURE OF CONSTRUCTIONAL PRODUCTS FROM CONCRETE AND CALCIUM-SILICATE - SAFETY - PART 1: COMMON REQUIREMENTS |
| I.S. EN 1114-1:2011 | PLASTICS AND RUBBER MACHINES - EXTRUDERS AND EXTRUSION LINES - PART 1: SAFETY REQUIREMENTS FOR EXTRUDERS |
| I.S. EN 12621:2006 | MACHINERY FOR THE SUPPLY AND CIRCULATION OF COATING MATERIALS UNDER PRESSURE - SAFETY REQUIREMENTS |
| I.S. EN 12981:2005 | COATING PLANTS - SPRAY BOOTHS FOR APPLICATION OF ORGANIC POWDER COATING MATERIAL - SAFETY REQUIREMENTS |
| I.S. EN 1612-2:2000 | PLASTICS AND RUBBER MACHINES - REACTION MOULDING MACHINES - PART 2: SAFETY REQUIREMENTS FOR REACTION MOULDING PLANT |
| I.S. EN 930:1998 | FOOTWEAR, LEATHER AND IMITATION LEATHER GOODS MANUFACTURING MACHINES - ROUGHING, SCOURING, POLISHING AND TRIMMING MACHINES - SAFETY REQUIREMENTS |
| I.S. EN 1034-5:2006 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 5: SHEETERS |
| I.S. EN 13355:2005 | COATING PLANTS - COMBINED BOOTHS - SAFETY REQUIREMENTS |
| I.S. EN 609-1:2017 | AGRICULTURAL AND FORESTRY MACHINERY - SAFETY OF LOG SPLITTERS - PART 1: WEDGE SPLITTERS |
| I.S. EN 617:2001 | |
| I.S. EN 1034-14:2006 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 14: REEL SPLITTER |
| I.S. EN 13591:2005 | FOOD PROCESSING MACHINERY - FIXED DECK OVEN LOADERS - SAFETY AND HYGIENE REQUIREMENTS |
| I.S. EN 201:2009 | PLASTICS AND RUBBER MACHINES - INJECTION MOULDING MACHINES - SAFETY REQUIREMENTS |
| I.S. EN 12984:2006 | FOOD PROCESSING MACHINERY - PORTABLE AND/OR HAND-GUIDED MACHINES AND APPLIANCES WITH MECHANICALLY DRIVEN CUTTING TOOLS - SAFETY AND HYGIENE REQUIREMENTS |
| I.S. EN 12653:2000 | FOOTWEAR, LEATHER AND IMITATION LEATHER MANUFACTURING MACHINES - NAILING MACHINES - SAFETY REQUIREMENTS |
| I.S. EN 13389:2005 | FOOD PROCESSING MACHINERY - MIXERS WITH HORIZONTAL SHAFTS - SAFETY AND HYGIENE REQUIREMENTS |
| I.S. EN 1010-1:2005 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PRINTING AND PAPER CONVERTING MACHINES - PART 1: COMMON REQUIREMENTS |
| I.S. EN 415-5:2006 | SAFETY OF PACKAGING MACHINES - PART 5: WRAPPING MACHINES |
| DIN EN 1034-5:2010-07 | Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 5: Sheeters (includes Amendment A1:2009) |
| I.S. EN 1417:2014 | PLASTICS AND RUBBER MACHINES - TWO-ROLL MILLS - SAFETY REQUIREMENTS |
| DIN EN 13788:2002-04 | MACHINE TOOLS - SAFETY - MULTI-SPINDLE AUTOMATIC TURNING MACHINES |
| I.S. EN 1756-1:2002 | TAIL LIFTS - PLATFORM LIFTS FOR MOUNTING ON WHEELED VEHICLES - SAFETY REQUIREMENTS - PART 1: TAIL LIFTS FOR GOODS |
| I.S. EN 12387:2005 | FOOTWEAR, LEATHER AND IMITATION LEATHER GOODS MANUFACTURING MACHINES - MODULAR SHOE REPAIR EQUIPMENT - SAFETY REQUIREMENTS |
| I.S. EN 710:1998 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR FOUNDRY MOULDING AND COREMAKING MACHINERY AND PLANT AND ASSOCIATED EQUIPMENT |
| DIN EN 1845:2008-06 | Footwear manufacturing machines - Footwear moulding machines - Safety requirements |
| I.S. EN 1845:2007 | FOOTWEAR MANUFACTURING MACHINES - FOOTWEAR MOULDING MACHINES - SAFETY REQUIREMENTS |
| I.S. EN 620:2002 | |
| I.S. EN 1501-1:2011 | REFUSE COLLECTION VEHICLES - GENERAL REQUIREMENTS AND SAFETY REQUIREMENTS - PART 1: REAR LOADED REFUSE COLLECTION VEHICLES |
| DIN EN 609-1:2017-04 | AGRICULTURAL AND FORESTRY MACHINERY - SAFETY OF LOG SPLITTERS - PART 1: WEDGE SPLITTERS |
| I.S. EN 1756-2:2004 | TAIL LIFTS - PLATFORM LIFTS FOR MOUNTING ON WHEELED VEHICLES - SAFETY REQUIREMENTS - PART 2: TAIL LIFTS FOR PASSENGERS |
| I.S. EN 415-7:2006 | SAFETY OF PACKAGING MACHINES - PART 7: GROUP AND SECONDARY PACKAGING MACHINES |
| I.S. EN 12581:2006 | COATING PLANTS - MACHINERY FOR DIP COATING AND ELECTRODEPOSITION OF ORGANIC LIQUID COATING MATERIAL - SAFETY REQUIREMENTS |
| I.S. EN 894-3:2000 | SAFETY OF MACHINERY - ERGONOMICS REQUIREMENTS FOR THE DESIGN OF DISPLAYS AND CONTROL ACTUATORS - PART 3: CONTROL ACTUATORS |
| I.S. EN 12463:2014 | FOOD PROCESSING MACHINERY - FILLING MACHINES AND AUXILIARY MACHINES - SAFETY AND HYGIENE REQUIREMENTS |
| I.S. EN 528:2008 | RAIL DEPENDENT STORAGE AND RETRIEVAL EQUIPMENT - SAFETY REQUIREMENTS |
| UNI EN 792-7 : 2008 | HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 7: GRINDERS |
| UNI EN 12387 : 2010 | FOOTWEAR, LEATHER AND IMITATION LEATHER GOODS MANUFACTURING MACHINES - MODULAR SHOE REPAIR EQUIPMENT - SAFETY REQUIREMENTS |
| UNI EN 792-11 : 2009 | HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 11: NIBBLERS AND SHEARS |
| ONORM EN 15094 : 2009 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR COLD FLAT ROLLING MILLS |
| NF EN 13885 : 2005 + A1 2010 | FOOD PROCESSING MACHINERY - CLIPPING MACHINES - SAFETY AND HYGIENE REQUIREMENTS |
| DIN EN 1501-3:2010-06 | Refuse collection vehicles and their associated lifting devices - General requirements and safety requirements - Part 3: Front loaded refuse collection vehicles |
| UNI EN 415-8 : 2008 | SAFETY OF PACKAGING MACHINES - PART 8: STRAPPING MACHINES |
| DIN EN 15165:2015-01 | FOOD PROCESSING MACHINERY - FORMING MACHINES - SAFETY AND HYGIENE REQUIREMENTS |
| I.S. EN 13788:2002 | MACHINE TOOLS - SAFETY - MULTI-SPINDLE AUTOMATIC TURNING MACHINES |
| DIN EN 15180:2015-01 | FOOD PROCESSING MACHINERY - FOOD DEPOSITORS - SAFETY AND HYGIENE REQUIREMENTS |
| 09/30201246 DC : 0 | BS EN 710:1997/A1 - SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR FOUNDRY MOULDING AND COREMAKING MACHINERY AND PLANT ASSOCIATED EQUIPMENT |
| 10/30232428 DC : DRAFT DEC 2010 | BS EN 1870-16 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 16: DOUBLE MITRE SAWING MACHINES FOR V CUTTING |
| UNI EN 15094 : 2009 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR COLD FLAT ROLLING MILLS |
| UNI EN ISO 8230-1 : 2009 | SAFETY REQUIREMENTS FOR DRY-CLEANING MACHINES - PART 1: COMMON SAFETY REQUIREMENTS |
| 11/30237563 DC : 0 | BS EN 1870-10 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 10: SINGLE BLADE AUTOMATIC AND SEMI-AUTOMATIC UP-CUTTING CROSS-CUT SAWING MACHINES |
| BS EN 1034-21:2012 | Safety of machinery. Safety requirements for the design and construction of paper making and finishing machines Coating machines |
| 10/30214958 DC : 0 | BS EN 1915-1 - AIRCRAFT GROUND SUPPORT EQUIPMENT - GENERAL REQUIREMENTS - PART 1: BASIC SAFETY REQUIREMENTS |
| 04/30110543 DC : 0 | EN 1845 - FOOTWEAR MANUFACTURING MACHINES - FOOTWEAR MOULDING MACHINES - SAFETY REQUIREMENTS |
| BS EN 15094:2008 | Safety of machinery. Safety requirements for cold flat rolling mills |
| UNI EN 14753 : 2008 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR MACHINERY AND EQUIPMENT FOR THE CONTINUOUS CASTING OF STEEL |
| DIN EN 14753:2008-03 | Safety of machinery - Safety requirements for machinery and equipment for continuous casting of steel |
| I.S. EN ISO 8230-1:2008 | SAFETY REQUIREMENTS FOR DRY-CLEANING MACHINES - PART 1: COMMON SAFETY REQUIREMENTS |
| I.S. EN 1034-21:2012 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 21: COATING MACHINES |
| I.S. EN 12013:2018 | PLASTICS AND RUBBER MACHINES - INTERNAL MIXERS - SAFETY REQUIREMENTS |
| I.S. EN 1501-5:2011 | REFUSE COLLECTION VEHICLES - GENERAL REQUIREMENTS AND SAFETY REQUIREMENTS - PART 5: LIFTING DEVICES FOR REFUSE COLLECTION VEHICLES |
| PREN 1870-10 : DRAFT 2011 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 10: SINGLE BLADE AUTOMATIC AND SEMI-AUTOMATIC UP-CUTTING CROSS-CUT SAWING MACHINES |
| PREN 12301 : DRAFT 2015 | PLASTICS AND RUBBER MACHINES - CALENDERS - SAFETY REQUIREMENTS |
| DIN EN 12921-1:2011-02 | Machines for surface cleaning and pre-treatment of industrial items using liquids or vapours - Part 1: Common safety requirements (includes Amendment A1:2010) |
| DIN EN 12629-6:2011-02 | Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 6: Stationary and mobile equipment for the manufacture of precast reinforced products (includes Amendment A1:2010) |
| I.S. EN 50191:2010 | ERECTION AND OPERATION OF ELECTRICAL TEST EQUIPMENT |
| DIN EN 1870-11:2014-02 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 11: SEMI AUTOMATIC HORIZONTAL CROSS-CUT SAWING MACHINES WITH ONE SAW UNIT (RADIAL ARM SAWS) |
| UNI EN 1501-2 : 2010 | REFUSE COLLECTION VEHICLES AND ASSOCIATED LIFTING DEVICES - GENERAL REQUIREMENTS AND SAFETY REQUIREMENTS - PART 2: SIDE LOADED REFUSE COLLECTION VEHICLES |
| DIN EN 12622:2014-02 | Safety of machine tools - Hydraulic press brakes (includes Amendment A1:2013) |
| DIN EN ISO 10472-6:2009-10 | Safety requirements for industrial laundry machinery - Part 6: Ironing and fusing presses (ISO 10472-6:1997) |
| DIN EN 12649:2011-09 | Concrete compactors and smoothing machines - Safety |
| DIN EN 12717:2009-07 | SAFETY OF MACHINE TOOLS - DRILLING MACHINES |
| DIN EN 792-11:2009-12 | HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 11: NIBBLERS AND SHEARS |
| DIN EN 13736:2009-11 | SAFETY OF MACHINE TOOLS - PNEUMATIC PRESSES |
| DIN EN 692:2009-10 | Machine tools - Mechanical presses - Safety (includes Amendment A1:2009) |
| DIN EN 930:2010-07 | Footwear, leather and imitation leather goods manufacturing machines - Roughing, scouring, polishing and trimming machines - Safety requirements (includes Amendment A2:2009) |
| DIN EN 12629-1:2011-01 | Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 1: Common requirements (includes Amendment A1:2010) |
| UNE-EN 710:1998 | SAFETY REQUIREMENTS FOR FOUNDRY MOULDING AND COREMAKING MACHINERY AND PLANT AND ASSOCIATED EQUIPMENT. |
| DIN EN 13885:2011-02 | Food processing machinery - Clipping machines - Safety and hygiene requirements (includes Amendment A1:2010) |
| DIN EN 620:2011-07 | Continuous handling equipment and systems - Safety and EMC requirements for fixed belt conveyors for bulk materials (includes Amendment A1:2010) |
| BS EN 999 : 1999 | SAFETY OF MACHINERY - THE POSITIONING OF PROTECTIVE EQUIPMENT IN RESPECT OF APPROACH SPEEDS OF PARTS OF THE HUMAN BODY |
| BS EN 12629-1 : 2001 | MACHINES FOR THE MANUFACTURE OF CONSTRUCTIONAL PRODUCTS FROM CONCRETE AND CALCIUM-SILICATE - SAFETY - PART 1: COMMON REQUIREMENTS |
| BS EN ISO 12100-1 : 2003 | SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 1: BASIC TERMINOLOGY, METHODOLOGY |
| BS EN 12478:2001 | Safety of machine tools. Large numerically controlled turning machines and turning centres |
| BS EN 1417:2014 | Plastics and rubber machines. Two-roll mills. Safety requirements |
| BS EN 13389 : 2005 | FOOD PROCESSING MACHINERY - MIXERS WITH HORIZONTAL SHAFTS - SAFETY AND HYGIENE REQUIREMENTS |
| BS EN 12151:2007 | Machinery and plants for the preparation of concrete and mortar. Safety requirements |
| BS EN 12649 : 2008 | CONCRETE COMPACTORS AND SMOOTHING MACHINES - SAFETY |
| UNE-EN 693:2001 | Machine tools - Safety - Hydraulic presses |
| EN 15095:2007+A1:2008 | Power-operated mobile racking and shelving, carousels and storage lifts - Safety requirements |
| UNI EN 12921-1 : 2010 | MACHINES FOR SURFACE CLEANING AND PRE- TREATMENT OF INDUSTRIAL ITEMS USING LIQUIDS OR VAPOURS - PART 1: COMMON SAFETY REQUIREMENTS |
| UNI EN ISO 12100-1 : 2009 | SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 1: BASIC TERMINOLOGY, METHODOLOGY |
| UNI EN 13288 : 2010 | FOOD PROCESSING MACHINERY - BOWL LIFTING AND TILTING MACHINES - SAFETY AND HYGIENE REQUIREMENTS |
| UNI EN 1612-2 : 2008 | PLASTICS AND RUBBER MACHINES - REACTION MOULDING MACHINES - PART 2: SAFETY REQUIREMENTS FOR REACTION MOULDING PLANT |
| UNI EN 12581 : 2010 | COATING PLANTS - MACHINERY FOR DIP COATING AND ELECTRODEPOSITION OF ORGANIC LIQUID COATING MATERIAL - SAFETY REQUIREMENTS |
| UNI EN 1010-1 : 2011 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PRINTING AND PAPER CONVERTING MACHINES - PART 1: COMMON REQUIREMENTS |
| UNI EN ISO 10472-6 : 2009 | SAFETY REQUIREMENTS FOR INDUSTRIAL LAUNDRY MACHINERY - PART 6: IRONING AND FUSING PRESSES |
| UNI EN 12629-6 : 2010 | MACHINES FOR THE MANUFACTURE OF CONSTRUCTIONAL PRODUCTS FROM CONCRETE AND CALCIUM-SILICATE - SAFETY - PART 6: STATIONARY AND MOBILE EQUIPMENT FOR THE MANUFACTURE OF PRECAST REINFORCED PRODUCTS |
| UNI EN 12203 : 2010 | FOOTWEAR, LEATHER AND IMITATION LEATHER GOODS MANUFACTURING MACHINES - SHOE AND LEATHER PRESSES - SAFETY REQUIREMENTS |
| UNI EN 15095 : 2009 | POWER-OPERATED MOBILE RACKING AND SHELVING, CAROUSELS AND STORAGE LIFTS - SAFETY REQUIREMENTS |
| UNI EN 1114-3 : 2009 | PLASTICS AND RUBBER MACHINES - EXTRUDERS AND EXTRUSION LINES - PART 3: SAFETY REQUIREMENTS FOR HAUL-OFFS |
| UNI EN ISO 12100-2 : 2009 | SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 2: TECHNICAL PRINCIPLES |
| UNI EN 13736 : 2009 | SAFETY OF MACHINE TOOLS - PNEUMATIC PRESSES |
| UNI EN 692 : 2009 | MACHINE TOOLS - MECHANICAL PRESSES - SAFETY |
| EN 617:2001+A1:2010 | Continuous handling equipment and systems - Safety and EMC requirements for the equipment for the storage of bulk materials in silos, bunkers, bins and hoppers |
| UNI EN 1114-1 : 2011 | PLASTICS AND RUBBER MACHINES - EXTRUDERS AND EXTRUSION LINES - PART 1: SAFETY REQUIREMENTS FOR EXTRUDERS |
| UNI EN 13389 : 2010 | FOOD PROCESSING MACHINERY - MIXERS WITH HORIZONTAL SHAFTS - SAFETY AND HYGIENE REQUIREMENTS |
| UNI EN 15067 : 2008 | PLASTICS AND RUBBER MACHINES - FILM CONVERTING MACHINES FOR BAGS AND SACKS - SAFETY REQUIREMENTS |
| UNI EN 617 : 2011 | CONTINUOUS HANDLING EQUIPMENT AND SYSTEMS - SAFETY AND EMC REQUIREMENTS FOR THE EQUIPMENT FOR THE STORAGE OF BULK MATERIALS IN SILOS, BUNKERS, BINS AND HOPPERS |
| UNI EN 1870-16 : 2012 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 16: DOUBLE MITRE SAWING MACHINES FOR V CUTTING |
| UNI EN 1845 : 2008 | FOOTWEAR MANUFACTURING MACHINES - FOOTWEAR MOULDING MACHINES - SAFETY REQUIREMENTS |
| UNI EN 415-6 : 2013 | SAFETY OF PACKAGING MACHINES - PART 6: PALLET WRAPPING MACHINES |
| UNI EN 12981 : 2009 | COATING PLANTS - SPRAY BOOTHS FOR APPLICATION OF ORGANIC POWDER COATING MATERIAL - SAFETY REQUIREMENTS |
| UNI EN 12649 : 2011 | CONCRETE COMPACTORS AND SMOOTHING MACHINES - SAFETY |
| UNI EN 12653 : 2010 | FOOTWEAR, LEATHER AND IMITATION LEATHER MANUFACTURING MACHINES - NAILING MACHINES - SAFETY REQUIREMENTS |
| UNI EN 12417 : 2009 | MACHINE TOOLS - SAFETY - MACHINING CENTRES |
| UNI EN 792-10 : 2009 | HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 10: COMPRESSION POWER TOOLS |
| UNI EN 12757-1 : 2010 | MIXING MACHINERY FOR COATING MATERIALS - SAFETY REQUIREMENTS - PART 1: MIXING MACHINERY FOR USE IN VEHICLE REFINISHING |
| UNI EN 12629-1 : 2010 | MACHINES FOR THE MANUFACTURE OF CONSTRUCTIONAL PRODUCTS FROM CONCRETE AND CALCIUM-SILICATE - SAFETY - PART 1: COMMON REQUIREMENTS |
| UNI EN 201 : 2010 | PLASTICS AND RUBBER MACHINES - INJECTION MOULDING MACHINES - SAFETY REQUIREMENTS |
| UNI EN 1870-11 : 2013 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 11: SEMI AUTOMATIC HORIZONTAL CROSS-CUT SAWING MACHINES WITH ONE SAW UNIT (RADIAL ARM SAWS) |
| UNI EN 1915-1 : 2014 | AIRCRAFT GROUND SUPPORT EQUIPMENT - GENERAL REQUIREMENTS - PART 1: BASIC SAFETY REQUIREMENTS |
| EN 1870-11:2013 | Safety of woodworking machines - Circular sawing machines - Part 11: Semi automatic horizontal cross-cut sawing machines with one saw unit (radial arm saws) |
| UNI EN 1870-9 : 2012 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 9: DOUBLE BLADE CIRCULAR SAWING MACHINES FOR CROSS-CUTTING WITH INTEGRATED FEED AND WITH MANUAL LOADING AND/OR UNLOADING |
| UNI EN 710 : 2010 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR FOUNDRY MOULDING AND COREMAKING MACHINERY AND PLANT AND ASSOCIATED EQUIPMENT |
| UNI EN 1756-2 : 2009 | TAIL LIFTS - PLATFORM LIFTS FOR MOUNTING ON WHEELED VEHICLES - SAFETY REQUIREMENTS - PART 2: TAIL LIFTS FOR PASSENGERS |
| UNI EN 1870-12 : 2014 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 12: PENDULUM CROSS-CUT SAWING MACHINES |
| UNI EN 12984 : 2010 | FOOD PROCESSING MACHINERY - PORTABLE AND/OR HAND-GUIDED MACHINES AND APPLIANCES WITH MECHANICALLY DRIVEN CUTTING TOOLS - SAFETY AND HYGIENE REQUIREMENTS |
| UNI EN 415-5 : 2010 | SAFETY OF PACKAGING MACHINES - PART 5: WRAPPING MACHINES |
| UNI EN 13885 : 2010 | FOOD PROCESSING MACHINERY - CLIPPING MACHINES - SAFETY AND HYGIENE REQUIREMENTS |
| UNI EN 1870-10 : 2013 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 10: SINGLE BLADE AUTOMATIC AND SEMI-AUTOMATIC UP-CUTTING CROSS-CUT SAWING MACHINES |
| UNI EN 12409 : 2011 | PLASTICS AND RUBBER MACHINES - THERMOFORMING MACHINES - SAFETY REQUIREMENTS |
| UNI EN 894-3 : 2009 | SAFETY OF MACHINERY - ERGONOMICS REQUIREMENTS FOR THE DESIGN OF DISPLAYS AND CONTROL ACTUATORS - PART 3: CONTROL ACTUATORS |
| UNI EN 930 : 2010 | FOOTWEAR, LEATHER AND IMITATION LEATHER GOODS MANUFACTURING MACHINES - ROUGHING, SCOURING, POLISHING AND TRIMMING MACHINES - SAFETY REQUIREMENTS |
| UNI EN 869 : 2009 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR PRESSURE METAL DIECASTING UNITS |
| UNI EN 12044 : 2010 | FOOTWEAR, LEATHER AND IMITATION LEATHER GOODS MANUFACTURING MACHINES - CUTTING AND PUNCHING MACHINES - SAFETY REQUIREMENTS |
| UNI EN 999 : 2008 | SAFETY OF MACHINERY - THE POSITIONING OF PROTECTIVE EQUIPMENT IN RESPECT OF APPROACH SPEEDS OF PARTS OF THE HUMAN BODY |
| UNI EN 14070 : 2009 | SAFETY OF MACHINE TOOLS - TRANSFER AND SPECIAL-PURPOSE MACHINES |
| UNI EN 693 : 2011 | MACHINE TOOLS - SAFETY - HYDRAULIC PRESSES |
| UNI EN 13128 : 2009 | SAFETY OF MACHINE TOOLS - MILLING MACHINES (INCLUDING BORING MACHINES) |
| UNI EN 1034-5 : 2010 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 5: SHEETERS |
| UNI EN 1034-14 : 2010 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 14: REEL SPLITTER |
| UNI EN 13355 : 2009 | COATING PLANTS - COMBINED BOOTHS - SAFETY REQUIREMENTS |
| UNI EN 12621 : 2010 | MACHINERY FOR THE SUPPLY AND CIRCULATION OF COATING MATERIALS UNDER PRESSURE - SAFETY REQUIREMENTS |
| UNI EN 12215 : 2010 | COATING PLANTS - SPRAY BOOTHS FOR APPLICATION OF ORGANIC LIQUID COATING MATERIALS - SAFETY REQUIREMENTS |
| UNI EN 12717 : 2009 | SAFETY OF MACHINE TOOLS - DRILLING MACHINES |
| UNI EN 415-7 : 2008 | SAFETY OF PACKAGING MACHINES - PART 7: GROUP AND SECONDARY PACKAGING MACHINES |
| UNI EN 289 : 2014 | PLASTICS AND RUBBER MACHINES - COMPRESSION MOULDING MACHINES AND TRANSFER MOULDING MACHINES - SAFETY REQUIREMENTS |
| UNI EN 13591 : 2010 | FOOD PROCESSING MACHINERY - FIXED DECK OVEN LOADERS - SAFETY AND HYGIENE REQUIREMENTS |
| UNI EN 12622 : 2014 | SAFETY OF MACHINE TOOLS - HYDRAULIC PRESS BRAKES |
| 10/30235571 DC : DRAFT DEC 2010 | BS EN 13418 - PLASTICS AND RUBBER MACHINES - WINDING MACHINES FOR FILM OR SHEET - SAFETY REQUIREMENTS |
| 10/30227080 DC : DRAFT JUNE 2010 | BS EN 691-1 - SAFETY OF WOODWORKING MACHINES - PART 1: COMMON REQUIREMENTS |
| 04/30124330 DC : 0 | EN 15067-1 - PLASTICS AND RUBBER MACHINES - WELDING MACHINES FOR PLASTICS - PART 1: SAFETY REQUIREMENTS FOR FILM CONVERTING MACHINES FOR BAGS AND SACKS |
| PREN 12013 : DRAFT 2015 | PLASTICS AND RUBBER MACHINES - INTERNAL MIXERS - SAFETY REQUIREMENTS |
| 13/30255092 DC : 0 | BS EN 1417 - PLASTICS AND RUBBER MACHINES - TWO ROLL MILLS - SAFETY REQUIREMENTS |
| 11/30237560 DC : 0 | BS EN 1870-12 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 12: PENDULUM CROSS-CUT SAWING MACHINES |
| UNI EN 1501-5 : 2011 | REFUSE COLLECTION VEHICLES - GENERAL REQUIREMENTS AND SAFETY REQUIREMENTS - PART 5: LIFTING DEVICES FOR REFUSE COLLECTION VEHICLES |
| I.S. EN 692:2005 | MACHINE TOOLS - MECHANICAL PRESSES - SAFETY |
| 15/30296744 DC : 0 | BS EN 12013 - PLASTICS AND RUBBER MACHINES - INTERNAL MIXERS - SAFETY REQUIREMENTS |
| BS EN 12012-1 : 2007 | PLASTICS AND RUBBER MACHINES - SIZE REDUCTION MACHINES - PART 1: SAFETY REQUIREMENTS FOR BLADE GRANULATORS |
| DIN EN 1501-5:2012-02 | Refuse collection vehicles - General requirements and safety requirements - Part 5: Lifting devices for refuse collection vehicles |
| BS ISO 4414:1998 | Pneumatic fluid power. General rules relating to systems |
| 12/30263881 DC : 0 | BS EN 1870-3 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 3: DOWN CUTTING CROSS-CUT SAWS AND DUAL PURPOSE DOWN CUTTING CROSS-CUT SAWS/CIRCULAR SAW BENCHES |
| I.S. EN 12478:2000 | SAFETY OF MACHINE TOOLS - LARGE NUMERICALLY CONTROLLED TURNING MACHINES AND TURNING CENTRES |
| BS EN 1501-5:2011 | Refuse collection vehicles. General requirements and safety requirements Lifting devices for refuse collection vehicles |
| 14/30310338 DC : 0 | BS EN 609-1 - AGRICULTURAL AND FORESTRY MACHINERY - SAFETY OF LOG SPLITTERS - PART 1: WEDGE SPLITTERS |
| 07/30172338 DC : DRAFT DEC 2007 | BS EN 1114-1 - PLASTICS AND RUBBER MACHINES - EXTRUDERS AND EXTRUSION LINES - PART 1: SAFETY REQUIREMENTS FOR EXTRUDERS |
| UNI EN 1501-3 : 2008 | REFUSE COLLECTION VEHICLES AND THEIR ASSOCIATED LIFTING DEVICES - GENERAL REQUIREMENTS AND SAFETY REQUIREMENTS - PART 3: FRONT LOADED REFUSE COLLECTION VEHICLES |
| 12/30268301 DC : 0 | BS EN 16486 - MACHINES FOR COMPACTING WASTE MATERIALS OR RECYCLABLE FRACTIONS - COMPACTORS - SAFETY REQUIREMENTS |
| I.S. EN 1672-1:2014 | FOOD PROCESSING MACHINERY - BASIC CONCEPTS - PART 1: SAFETY REQUIREMENTS |
| PREN 15180 : DRAFT 2011 | FOOD PROCESSING MACHINERY - FOOD DEPOSITORS - SAFETY AND HYGIENE REQUIREMENTS |
| 05/19981969 DC : DRAFT JUN 2005 | BS EN 1034-5 - SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 5: SHEETERS |
| 09/30179773 DC : 0 | BS EN 12387:2005/A1 - FOOTWEAR, LEATHER AND IMITATION LEATHER GOODS MANUFACTURING MACHINES - MODULAR SHOE REPAIR EQUIPMENT - SAFETY REQUIREMENTS |
| 07/30170114 DC : 0 | BS EN 201 - PLASTICS AND RUBBER MACHINES - INJECTION MOULDING MACHINES - SAFETY REQUIREMENTS |
| 04/30126179 DC : DRAFT DEC 2004 | EN 15095 - POWER-OPERATED MOBILE RACKING AND SHELVING, CARROUSELS AND STORAGE LIFTS - SAFETY REQUIREMENTS |
| I.S. EN 15165:2014 | FOOD PROCESSING MACHINERY - FORMING MACHINES - SAFETY AND HYGIENE REQUIREMENTS |
| DIN EN 16500:2014-10 | MACHINES FOR COMPACTING WASTE MATERIALS OR RECYCLABLE FRACTIONS - VERTICAL BALING PRESSES - SAFETY REQUIREMENTS |
| 12/30260299 DC : 0 | BS EN 15165 - FOOD PROCESSING MACHINERY - FORMING MACHINES - SAFETY AND HYGIENE REQUIREMENTS |
| 04/30124187 DC : 0 | PREN 415-8 - SAFETY OF PACKAGING MACHINES - PART 8: STRAPPING MACHINES |
| 00/707575 DC : DRAFT APR 2000 | ISO/DIS 12100-1 - SAFETY OF MACHINERY - BASIC CONCEPTS AND GENERAL PRINCIPLES FOR DESIGN - PART 1: BASIC TERMINOLOGY AND METHODOLOGY |
| 95/700501 DC : DRAFT JAN 1995 | PREN 1756-1 SPECIFICATION FOR TAIL LIFTS - PLATFORM LIFTS FOR MOUNTING ON WHEELED VEHICLES - SAFETY REQUIREMENTS - PART 1: TAIL LIFTS FOR GOODS |
| DIN EN 16500 E : 2014 | MACHINES FOR COMPACTING WASTE MATERIALS OR RECYCLABLE FRACTIONS - VERTICAL BALING PRESSES - SAFETY REQUIREMENTS |
| DIN EN ISO 8230-1:2009-05 | SAFETY REQUIREMENTS FOR DRY-CLEANING MACHINES - PART 1: COMMON SAFETY REQUIREMENTS |
| UNE-EN 1672-1:2015 | Food processing machinery - Basic concepts - Part 1: Safety requirements |
| I.S. EN 15094:2008 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR COLD FLAT ROLLING MILLS |
| ISO 9355-3:2006 | Ergonomic requirements for the design of displays and control actuators — Part 3: Control actuators |
| EN 12012-1:2007+A1:2008 | Plastics and rubber machines - Size reduction machines - Part 1: Safety requirements for blade granulators |
| BS EN 12013:2018 | Plastics and rubber machines. Internal mixers. Safety requirements |
| EN 1756-1:2001+A1:2008 | Tail lifts - Platform lifts for mounting on wheeled vehicles - Safety requirements - Part 1: Tail lifts for goods |
| PREN 609-1 : DRAFT 2014 | AGRICULTURAL AND FORESTRY MACHINERY - SAFETY OF LOG SPLITTERS - PART 1: WEDGE SPLITTERS |
| DIN EN 12757-1:2011-02 | Mixing machinery for coating materials - Safety requirements - Part 1: Mixing machinery for use in vehicle refinishing (includes Amendment A1:2010) |
| UNE-EN 1915-1:2013 | Aircraft ground support equipment - General requirements - Part 1: Basic safety requirements |
| EN 620:2002+A1:2010 | Continuous handling equipment and systems - Safety and EMC requirements for fixed belt conveyors for bulk materials |
| DIN EN 710:2010-10 | Safety of machinery - Safety requirements for foundry moulding and coremaking machinery and plant and associated equipment (includes Amendment A1:2010) |
| DIN EN 201:2010-02 | PLASTICS AND RUBBER MACHINES - INJECTION MOULDING MACHINES - SAFETY REQUIREMENTS |
| DIN EN 528:2009-02 | Rail dependent storage and retrieval equipment - Safety requirements |
| DIN EN 617:2011-06 | Continuous handling equipment and systems - Safety and EMC requirements for the equipment for the storage of bulk materials in silos, bunkers, bins and hoppers (includes Amendment A1:2010) |
| DIN EN 1114-1:2012-01 | Plastics and rubber machines - Extruders and extrusion lines - Part 1: Safety requirements for extruders |
| DIN EN 1114-3:2015-12 (Draft) | PLASTICS AND RUBBER MACHINES - EXTRUDERS AND EXTRUSION LINES - PART 3: SAFETY REQUIREMENTS FOR HAUL-OFFS |
| BS EN 415-5 : 2006 | SAFETY OF PACKAGING MACHINES - PART 5: WRAPPING MACHINES |
| BS EN 13885 : 2005 | FOOD PROCESSING MACHINERY - CLIPPING MACHINES - SAFETY AND HYGIENE REQUIREMENTS |
| BS EN 1870-12:2013 | Safety of woodworking machines. Circular sawing machines Pendulum cross-cut sawing machines |
| BS EN 792-11 : 2000 | HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 11: NIBBLERS AND SHEARS |
| BS EN 1612-2 : 2000 | PLASTICS AND RUBBER MACHINES - REACTION MOULDING MACHINES - PART 2: SAFETY REQUIREMENTS FOR REACTION MOULDING PLANT |
| ISO 8230-1:2008 | Safety requirements for dry-cleaning machines Part 1: Common safety requirements |
| UNE-EN 12621:2006 | Machinery for the supply and circulation of coating materials under pressure - Safety requirements |
| BS EN 1114-1:2011 | Plastics and rubber machines. Extruders and extrusion lines Safety requirements for extruders |
| BS EN 1010-1 : 2004 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PRINTING AND PAPER CONVERTING MACHINES - PART 1: COMMON REQUIREMENTS |
| BS EN 869 : 2006 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR PRESSURE METAL DIECASTING UNITS |
| BS EN 12840:2001 | Safety of machine tools. Manually controlled turning machines with or without automatic control |
| BS EN 12417 : 2001 | MACHINE TOOLS - SAFETY - MACHINING CENTRES |
| BS EN 12463:2014 | Food processing machinery. Filling machines and auxiliary machines. Safety and hygiene requirements |
| BS EN 1756-2 : 2004 | TAIL LIFTS - PLATFORM LIFTS FOR MOUNTING ON WHEELED VEHICLES - SAFETY REQUIREMENTS - PART 2: TAIL LIFTS FOR PASSENGERS |
| BS EN 13736 : 2003 | SAFETY OF MACHINE TOOLS - PNEUMATIC PRESSES |
| BS EN 12621 : 2006 | MACHINERY FOR THE SUPPLY AND CIRCULATION OF COATING MATERIALS UNDER PRESSURE - SAFETY REQUIREMENTS |
| UNE-EN 13288:2006 | Food processing machinery - Bowl lifting and tilting machines - Safety and hygiene requirements |
| UNE-EN 12649:2009 | Concrete compactors and smoothing machines - Safety |
| UNE-EN 415-6:2014 | Safety of packaging machines - Part 6: Pallet wrapping machines |
| BS EN 201:2009 | Plastics and rubber machines. Injection moulding machines. Safety requirements |
| BS EN 1726-2:2000 | Safety of industrial trucks. Self-propelled trucks up to and including 10000 kg capacity and industrial tractors with a drawbar pull up to and including 20000 N Additional requirements for trucks with elevating operator position and trucks specifically designed to travel with elevated loads |
| BS EN 930 : 1997 | FOOTWEAR, LEATHER AND IMITATION LEATHER GOODS MANUFACTURING MACHINES - ROUGHING, SCOURING, POLISHING AND TRIMMING MACHINES - SAFETY REQUIREMENTS |
| BS EN 12717 : 2001 | SAFETY OF MACHINE TOOLS - DRILLING MACHINES |
| UNE-EN 12622:2011 | Safety of machine tools - Hydraulic press brakes |
| BS EN 13288 : 2005 | FOOD PROCESSING MACHINERY - BOWL LIFTING AND TILTING MACHINES - SAFETY AND HYGIENE REQUIREMENTS |
| BS EN 1756-1 : 2001 | TAIL LIFTS - PLATFORM LIFTS FOR MOUNTING ON WHEELED VEHICLES - SAFETY REQUIREMENTS - PART 1: TAIL LIFTS FOR GOODS |
| ISO 10472-6:1997 | Safety requirements for industrial laundry machinery Part 6: Ironing and fusing presses |
| BS EN 415-7 : 2006 | SAFETY OF PACKAGING MACHINES - PART 7: GROUP AND SECONDARY PACKAGING MACHINES |
| BS EN 1870-3:2014 | Safety of woodworking machines. Circular sawing machines Down cutting cross-cut saws and dual purpose down cutting cross-cut saws/circular saw benches |
| BS EN 1870-11:2013 | Safety of woodworking machines. Circular sawing machines Semi automatic horizontal cross-cut sawing machines with one saw unit (radial arm saws) |
| BS EN 693 : 2001 | MACHINE TOOLS - SAFETY - HYDRAULIC PRESSES |
| BS EN 1501-1 : 2011 | REFUSE COLLECTION VEHICLES - GENERAL REQUIREMENTS AND SAFETY REQUIREMENTS - PART 1: REAR LOADED REFUSE COLLECTION VEHICLES |
| BS EN 14070 : 2003 | SAFETY OF MACHINE TOOLS - TRANSFER AND SPECIAL-PURPOSE MACHINES |
| UNE-EN 617:2002 | Continuous handling equipment and systems- Safety and EMC requirements for the equipment for the storage of bulk materials in silos, bunkers, bins and hoppers. |
| BS EN 12415:2001 | Safety of machine tools. Small numerically controlled turning machines and turning centres |
| BS EN 12044 : 2005 | FOOTWEAR, LEATHER AND IMITATION LEATHER GOODS MANUFACTURING MACHINES - CUTTING AND PUNCHING MACHINES - SAFETY REQUIREMENTS |
| BS EN 13788:2002 | Machine tools. Safety. Multi-spindle automatic turning machines |
| UNE-EN 12409:2009 | Plastics and rubber machines - Thermoforming machines - Safety requirements |
| UNE-EN 13591:2006 | Food processing machinery - Fixed deck oven loaders - Safety and hygiene requirements |
| UNE-EN 1870-9:2013 | Safety of woodworking machines - Circular sawing machines - Part 9: Double blade circular sawing machines for cross-cutting with integrated feed and with manual loading and/or unloading |
| BS EN ISO 11111:1996 | Safety requirements for textile machinery |
| BS EN 1114-3 : 2001 | PLASTICS AND RUBBER MACHINES - EXTRUDERS AND EXTRUSION LINES - PART 3: SAFETY REQUIREMENTS FOR HAUL-OFFS |
| UNE-EN 1756-2:2005 | Tail lifts - Platform lifts for mounting on wheeled vehicles - Safety requirements - Part 2: Tail lifts for passengers |
| UNE-EN 1870-16:2013 | Safety of woodworking machines - Circular sawing machines - Part 16: Double mitre sawing machines for V cutting |
| UNE-EN 13389:2006 | Food processing machinery. Mixers with horizontal shafts. Safety and hygiene requirements. |
| 09/30205281 DC : 0 | BS EN 50191 - ERECTION AND OPERATION OF ELECTRICAL TEST EQUIPMENT |
| BS EN 13591 : 2005 | FOOD PROCESSING MACHINERY - FIXED DECK OVEN LOADERS - SAFETY AND HYGIENE REQUIREMENTS |
| UNE-EN 620:2002 | Continuous handling equipment and systems - Safety and EMC requirements for fixed belt conveyors for bulk materials |
| BS EN ISO 10472-6:2008 | Safety requirements for industrial laundry machinery Ironing and fusing presses |
| DIN EN 15095:2009-06 | POWER-OPERATED MOBILE RACKING AND SHELVING, CAROUSELS AND STORAGE LIFTS - SAFETY REQUIREMENTS |
| UNE-EN 1114-1:2012 | Plastics and rubber machines - Extruders and extrusion lines - Part 1: Safety requirements for extruders |
| DIN EN 999:2008-10 | SAFETY OF MACHINERY - THE POSITIONING OF PROTECTIVE EQUIPMENT IN RESPECT OF APPROACH SPEED OF PARTS OF THE HUMAN BODY |
| DIN EN 792-11:2001-02 | HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 11: NIBBLERS AND SHEARS |
| EN 13788 : 2001 | MACHINE TOOLS - SAFETY - MULTI-SPINDLE AUTOMATIC TURNING MACHINES |
| EN 13885:2005+A1:2010 | Food processing machinery - Clipping machines - Safety and hygiene requirements |
| EN 201:2009 | Plastics and rubber machines - Injection moulding machines - Safety requirements |
| EN 692:2005+A1:2009 | Machine tools - Mechanical presses - Safety |
| EN 792-7:2001+A1:2008 | Hand-held non-electric power tools - Safety requirements - Part 7: Grinders |
| EN 15067:2007 | Plastics and rubber machines - Film converting machines for bags and sacks - Safety requirements |
| EN 1417:2014 | Plastics and rubber machines - Two-roll mills - Safety requirements |
| EN 894-3:2000+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 3: Control actuators |
| EN 415-8:2008 | Safety of packaging machines - Part 8: Strapping machines |
| EN 415-7:2006+A1:2008 | Safety of packaging machines - Part 7: Group and secondary packaging machines |
| EN 1915-1:2013 | Aircraft ground support equipment - General requirements - Part 1: Basic safety requirements |
| EN 12984:2005+A1:2010 | Food processing machinery - Portable and/or hand-guided machines and appliances with mechanically driven cutting tools - Safety and hygiene requirements |
| EN 15094:2008 | Safety of Machinery - Safety requirements for cold flat rolling mills |
| EN 999:1998+A1:2008 | Safety of machinery - The positioning of protective equipment in respect of approach speeds of parts of the human body |
| EN 1672-1:2014 | Food processing machinery - Basic concepts - Part 1: Safety requirements |
| EN 609-1:2017 | Agricultural and forestry machinery - Safety of log splitters - Part 1: Wedge splitters |
| EN 792-10:2000+A1:2008 | Hand-held non-electric power tools - Safety requirements - Part 10: Compression power tools |
| EN 1612-2:2000+A1:2008 | Plastics and rubber machines - Reaction moulding machines - Part 2: Safety requirements for reaction moulding plant |
| EN 1870-16:2012 | Safety of woodworking machines - Circular sawing machines - Part 16: Double mitre sawing machines for V cutting |
| EN 13591:2005+A1:2009 | Food processing machinery - Fixed deck oven loaders - Safety and hygiene requirements |
| EN 12581:2005+A1:2010 | Coating plants - Machinery for dip coating and electrodeposition of organic liquid coating material - Safety requirements |
| EN ISO 10472-6:2008 | Safety requirements for industrial laundry machinery - Part 6: Ironing and fusing presses (ISO 10472-6:1997) |
| EN 1726-2:2000 | Safety of Industrial Trucks - Self-propelled trucks up to and including 10000 kg capacity and tractors with a drawbar pull up to and including 20000 N - Part 2: Additional requirements for trucks with elevating operator position and trucks specifically designed to travel with elevated loads |
| EN 1756-2:2004+A1:2009 | Tail lifts - Platform lifts for mounting on wheeled vehicles - Safety requirements - Part 2: Tail lifts for passengers |
| EN 930:1997+A2:2009 | Footwear, leather and imitation leather goods manufacturing machines - Roughing, scouring, polishing and trimming machines - Safety requirements |
| EN 16500:2014 | Machines for compacting waste materials or recyclable fractions - Vertical baling presses - Safety requirements |
| EN 1870-3:2014 | Safety of woodworking machines - Circular sawing machines - Part 3: Down cutting cross-cut saws and dual purpose down cutting cross-cut saws/circular saw benches |
| EN 1845:2007 | Footwear manufacturing machines - Footwear moulding machines - Safety requirements |
| EN 869:2006+A1:2009 | Safety of machinery - Safety requirements for pressure metal diecasting units |
| EN 792-11:2000+A1:2008 | Hand-held non-electric power tools - Safety requirements - Part 11: Nibblers and shears |
| EN 15165:2014 | Food processing machinery - Forming machines - Safety and hygiene requirements |
| EN 693 : 2001 COR 2011 | MACHINE TOOLS - SAFETY - HYDRAULIC PRESSES |
| EN 14753:2007 | Safety of machinery - Safety requirements for machinery and equipment for continuous casting of steel |
| EN 415-6:2013 | Safety of packaging machines - Part 6: Pallet wrapping machines |
| EN 15180:2014 | Food processing machinery - Food depositors - Safety and hygiene requirements |
| EN 289:2014 | Plastics and rubber machines - Compression moulding machines and transfer moulding machines - Safety requirements |
| EN 415-5:2006+A1:2009 | Safety of packaging machines - Part 5: Wrapping machines |
| EN 1870-12:2013 | Safety of woodworking machines - Circular sawing machines - Part 12: Pendulum cross-cut sawing machines |
| EN 1870-10:2013 | Safety of woodworking machines - Circular sawing machines - Part 10: Single blade automatic and semi-automatic up-cutting cross-cut sawing machines |
| EN 1870-9:2012 | Safety of woodworking machines - Circular sawing machines - Part 9: Double blade circular sawing machines for cross-cutting with integrated feed and with manual loading and/or unloading |
| EN 13736:2003+A1:2009 | Safety of machine tools - Pneumatic presses |
| EN ISO 8230-1:2008 | Safety requirements for dry-cleaning machines - Part 1: Common safety requirements (ISO 8230-1:2008) |
| UNI EN 528 : 2009 | RAIL DEPENDENT STORAGE AND RETRIEVAL EQUIPMENT - SAFETY REQUIREMENTS |
| DIN EN 1034-21:2012-11 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 21: COATING MACHINES |
| DIN EN 1672-1:2014-12 | FOOD PROCESSING MACHINERY - BASIC CONCEPTS - PART 1: SAFETY REQUIREMENTS |
| BS EN 16500:2014 | Machines for compacting waste materials or recyclable fractions. Vertical baling presses. Safety requirements |
| I.S. EN 792-7:2002 | HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 7: GRINDERS |
| BS EN 15165:2014 | Food processing machinery. Forming machines. Safety and hygiene requirements |
| 03/301332 DC : DRAFT JAN 2003 | ISO 12649 - GRAPHIC TECHNOLOGY - SAFETY REQUIREMENTS FOR BINDING AND FINISHING SYSTEMS AND EQUIPMENT |
| 98/717506 DC : DRAFT DEC 1998 | PREN 13389 - FOOD PROCESSING MACHINERY - MIXERS WITH HORIZONTAL SHAFTS - SAFETY AND HYGIENE REQUIREMENTS |
| DIN EN 415-8:2011-06 | Safety of packaging machines - Part 8: Strapping machines; German version EN 415-8:2008 |
| I.S. EN 12417:2001 | MACHINE TOOLS - SAFETY - MACHINING CENTRES |
| 00/717064 DC : DRAFT NOV 2000 | PREN 14070 - SAFETY OF MACHINES TOOLS - TRANSFER AND SPECIAL PURPOSE MACHINES |
| 05/19981949 DC : DRAFT MAY 2005 | BS EN 1034-14 - SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 14: REEL SPLICERS |
| I.S. EN 415-8:2008 | SAFETY OF PACKAGING MACHINES - PART 8: STRAPPING MACHINES |
| BS EN 50191:2010 | Erection and operation of electrical test equipment |
| BS ISO 4413:1998 | Hydraulic fluid power. General rules relating to systems |
| 02/711304 DC : DRAFT SEP 2002 | BS EN 415-5 - PACKAGING MACHINES SAFETY - PART 5: WRAPPING MACHINES |
| 02/705139 DC : DRAFT APR 2002 | PREN 1870-16 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 16: DOUBLE MITRE SAWING MACHINES FOR V-CUTTING |
| NF EN 12649 : 2008 + A1 2011 | CONCRETE COMPACTORS AND SMOOTHING MACHINES - SAFETY |
| I.S. EN 1501-3:2008 | REFUSE COLLECTION VEHICLES AND THEIR ASSOCIATED LIFTING DEVICES - GENERAL REQUIREMENTS AND SAFETY REQUIREMENTS - PART 3: FRONT LOADED REFUSE COLLECTION VEHICLES |
| UNI EN 1672-1 : 2014 | FOOD PROCESSING MACHINERY - BASIC CONCEPTS - PART 1: SAFETY REQUIREMENTS |
| 15/30314036 DC : 0 | BS EN 12012-1 - PLASTICS AND RUBBER MACHINES - SIZE REDUCTION MACHINES - PART 1: SAFETY REQUIREMENTS FOR BLADE GRANULATORS AND SHREDDERS |
| PREN 1417 : DRAFT 2013 | PLASTICS AND RUBBER MACHINES - TWO ROLL MILLS - SAFETY REQUIREMENTS |
| I.S. EN 12012-1:2007 | PLASTICS AND RUBBER MACHINES - SIZE REDUCTION MACHINES - PART 1: SAFETY REQUIREMENTS FOR BLADE GRANULATORS |
| UNE-EN 12463:2006 | Food processing machinery - Filling machines and auxiliary machines - Safety and hygiene requirements |
| DIN EN 415-6:2013-09 | Safety of packaging machines - Part 6: Pallet wrapping machines |
| DIN EN 1501-1:2016-03 | Refuse collection vehicles - General requirements and safety requirements - Part 1: Rear loaded refuse collection vehicles (includes Amendment A1:2015) |
| DIN EN 1501-2:2010-02 | Refuse collection vehicles and their associated lifting devices - General requirements and safety requirements - Part 2: Side loaded refuse collection vehicles (includes Amendment A1:2009) |
| DIN EN 792-10:2009-12 | HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 10: COMPRESSION POWER TOOLS |
| DIN EN 289:2014-09 | PLASTICS AND RUBBER MACHINES - COMPRESSION MOULDING MACHINES AND TRANSFER MOULDING MACHINES - SAFETY REQUIREMENTS |
| BS EN 1845:2007 | Footwear manufacturing machines. Footwear moulding machines. Safety requirements |
| BS EN 609-1:2017 | Agricultural and forestry machinery. Safety of log splitters Wedge splitters |
| BS EN 692 : 2005 | MACHINE TOOLS - MECHANICAL PRESSES - SAFETY |
| BS EN 12581 : 2005 | COATING PLANTS - MACHINERY FOR DIP COATING AND ELECTRODEPOSITION OF ORGANIC LIQUID COATING MATERIAL - SAFETY REQUIREMENTS |
| BS EN 1870-16:2012 | Safety of woodworking machines. Circular sawing machines Double mitre sawing machines for V cutting |
| BS EN 1915-1:2013 | Aircraft ground support equipment. General requirements Basic safety requirements |
| BS EN 617 : 2001 | |
| BS EN 12921-1 : 2005 | MACHINES FOR SURFACE CLEANING AND PRE-TREATMENT OF INDUSTRIAL ITEMS USING LIQUIDS OR VAPOURS - PART 1: COMMON SAFETY REQUIREMENTS |
| BS EN 792-7 : 2001 | HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 7: GRINDERS |
| ISO 12100-1:2003 | Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology |
| EN 1114-3:2001+A1:2008 | Plastics and rubber machines - Extruders and extrusion lines - Part 3: Safety requirements for haul-offs |
| EN 1034-14:2005+A1:2009 | Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 14: Reel splitter |
| EN 13288:2005+A1:2009 | Food processing machinery - Bowl lifting and tilting machines - Safety and hygiene requirements |
| EN 12387:2005+A1:2009 | Footwear, leather and imitation leather goods manufacturing machines - Modular shoe repair equipment - Safety requirements |
| EN 12415:2000/A1:2002 | SAFETY OF MACHINE TOOLS - SMALL NUMERICALLY CONTROLLED TURNING MACHINES AND TURNING CENTRES |
| EN 12981:2005+A1:2009 | Coating plants - Spray booths for application of organic powder coating material - Safety requirements |
| EN 12629-6:2004+A1:2010 | Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 6: Stationary and mobile equipment for the manufacture of precast reinforced products |
| UNI EN 1756-1 : 2008 | TAIL LIFTS - PLATFORM LIFTS FOR MOUNTING ON WHEELED VEHICLES - SAFETY REQUIREMENTS - PART 1: TAIL LIFTS FOR GOODS |
| EN 12629-1:2000+A1:2010 | Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 1: Common requirements |
| UNI EN 620 : 2011 | CONTINUOUS HANDLING EQUIPMENT AND SYSTEMS - SAFETY AND EMC REQUIREMENTS FOR FIXED BELT CONVEYORS FOR BULK MATERIALS |
| EN 12840 : 2001 | SAFETY OF MACHINE-TOOLS - MANUALLY CONTROLLED TURNING MACHINES WITH OR WITHOUT AUTOMATIC CONTROL |
| EN 1501-2:2005+A1:2009 | Refuse collection vehicles and associated lifting devices - General requirements and safety requirements - Part 2: Side loaded refuse collection vehicles |
| DIN EN 12151:2008-05 | MACHINERY AND PLANTS FOR THE PREPARATION OF CONCRETE AND MORTAR - SAFETY REQUIREMENTS |
| EN 13389:2005+A1:2009 | Food processing machinery - Mixers with horizontal shafts - Safety and hygiene requirements |
| EN 1501-3:2008 | Refuse collection vehicles and their associated lifting devices - General requirements and safety requirements - Part 3: Front loaded refuse collection vehicles |
| DIN EN 12012-1:2010-02 | PLASTICS AND RUBBER MACHINES - SIZE REDUCTION MACHINES - PART 1: SAFETY REQUIREMENTS FOR BLADE GRANULATORS |
| DIN EN 792-10:2001-02 | HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 10: COMPRESSION POWER TOOLS |
| UNE-EN 1034-5:2006 | Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 5: Sheeters |
| UNE-EN 12203:2004 | Footwear, leather and imitation leather goods manufacturing machines - Shoe and leather presses - Safety requirements |
| UNE-EN 12629-6:2005 | Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 6: Stationary and mobile equipment for the manufacture of precast reinforced products |
| UNE-EN 12757-1:2006+A1:2010 | Mixing machinery for coating materials - Safety requirements - Part 1: Mixing machinery for use in vehicle refinishing |
| UNE-EN 1501-2:2006 | Refuse collection vehicles and associated lifting devices - General requirements and safety requirements - Part 2: Side loaded refuse collection vehicles |
| UNE-EN 12757-1:2006 | Mixing machinery for coating materials - Safety requirements - Part 1: Mixing machinery for use in vehicle refinishing |
| UNE-EN 415-5:2007 | Safety of packaging machines - Part 5: Wrapping machines |
| UNE-EN 12044:2006 | Footwear, leather and imitation leather goods manufacturing machines - Cutting and punching machines - Safety requirements |
| UNE-EN 12629-1:2001 | MACHINES FOR THE MANUFACTURE OF CONSTRUCTIONAL PRODUCTS FORM CONCRETE AND CALCIUM-SILICATE. SAFETY. PART 1: COMMON REQUIREMENTS |
| UNE-EN 1034-14:2006 | Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 14: Reel splitter |
| UNE-EN 1501-1:2012 | Refuse collection vehicles - General requirements and safety requirements - Part 1: Rear loaded refuse collection vehicles |
| EN 1050 : 1996 | SAFETY OF MACHINERY - PRINCIPLES FOR RISK ASSESSMENT |
| EN 292-1 : 1991 | SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - BASIC TERMINOLOGY, METHODOLOGY |
| DIN V VDE 0801 : 1990 AMD 1 1994 | PRINCIPLES FOR COMPUTERS IN SAFETY-RELATED SYSTEMS |
| EN 954-1 : 1996 | SAFETY OF MACHINERY - SAFETY-RELATED PARTS OF CONTROL SYSTEMS - PART 1: GENERAL PRINCIPLES FOR DESIGN |
| EN 292-2 : 91 AMD 1 95 | SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - TECHNICAL PRINCIPLES AND SPECIFICATION |
| 1998/37/EC : 1998 | DIRECTIVE 98/37/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 22 JUNE 1998 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES RELATING TO MACHINERY |
| EN 60204-1 : 2006 COR 2010 | SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.