• EN 13611:2015/AC:2016

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS AND/OR LIQUID FUELS - GENERAL REQUIREMENTS

    Available format(s): 

    Superseded date:  28-02-2022

    Language(s): 

    Published date:  12-01-2013

    Publisher:  Comite Europeen de Normalisation

    Pure ENs are not available for sale, please purchase a suitable national adoption

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Classification
    5 Test conditions and uncertainty of measurements
    6 Design and construction
    7 Performance
    8 Electrical requirements
    9 Electromagnetic compatibility (EMC)
    10 Marking, installation and operating instructions
    Annex A (informative) - Abbreviations and Symbols
    Annex B (informative) - Leak-tightness tests for gas
            controls - volumetric method
    Annex C (informative) - Leak-tightness tests for gas
            controls - pressure loss method
    Annex D (normative) - Calculation of pressure loss into
            leakage rate
    Annex E (normative) - Electrical/electronic component
            fault modes
    Annex F (normative) - Additional requirements for safety
            accessories and pressure accessories as defined in
            EU Directive 97/23/EC
    Annex G (normative) - Materials for pressurized parts
    Annex H (normative) - Additional materials for pressurized
            parts
    Annex I (normative) - Requirements for controls used in DC
            supplied burners and appliances burning gaseous or
            liquid fuels
    Annex J (normative) - Method for the determination of a
            Safety integrity level (SIL)
    Annex K (normative) - Method for the determination of a
            Performance Level (PL)
    Annex L (informative) - Relationship between Safety Integrity
            Level (SIL) and Performance Level (PL)
    Annex M (normative) - Reset functions
    Annex N (informative) - Guidance document on
            Environmental Aspects
    Annex O (normative) - Seals of elastomer, cork and
            synthetic fibre mixtures
    Annex ZA (informative) - Relationship between this
             European Standard and the Essential
             Requirements of EU Directive 2009/142/EC
    Annex ZB (informative) - Relationship between this
             European Standard and the Essential
             Requirements of EU Directive 97/23/EC
    Bibliography

    Abstract - (Show below) - (Hide below)

    Provides the general safety, design, construction, and performance requirements and testing for safety, control or regulating devices (hereafter referred to as controls) for burners and appliances burning one or more gaseous fuels or liquid fuels.

    General Product Information - (Show below) - (Hide below)

    Committee TC 58
    Development Note To be read in conjunction with EN 88-1, EN 88-2, EN 125, EN 126, EN 161, EN 257, EN 298, EN 1106, EN 1643, EN 1854, EN 12067-1, EN 12067-2 and EN 12078. (12/2007)
    Document Type Standard
    Publisher Comite Europeen de Normalisation
    Status Superseded
    Superseded By

    Standards Referenced By This Book - (Show below) - (Hide below)

    PREN 1643 : DRAFT 2012 VALVE PROVING SYSTEMS FOR AUTOMATIC SHUT-OFF VALVES FOR GAS BURNERS AND GAS APPLIANCES
    DIN EN 16304:2013-05 AUTOMATIC VENT VALVES FOR GAS BURNERS AND GAS BURNING APPLIANCES
    DIN EN 16830 E : 2017 SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS OR LIQUID FUELS - CONTROL FUNCTIONS IN ELECTRONIC SYSTEMS - TEMPERATURE CONTROL FUNCTION
    I.S. EN 16475-2:2017 CHIMNEYS - ACCESSORIES - PART 2: CHIMNEY FANS - REQUIREMENTS AND TEST METHODS
    DIN EN 16475-2 E : 2017 CHIMNEYS - ACCESSORIES - PART 2: CHIMNEY FANS - REQUIREMENTS AND TEST METHODS
    DIN EN 16678 E : 2016 SAFETY AND CONTROL DEVICES FOR GAS BURNERS AND GAS BURNING APPLIANCES - AUTOMATIC SHUTOFF VALVES FOR OPERATING PRESSURE OF ABOVE 500 KPA UP TO AND INCLUDING 6300 KPA
    BS EN 16314 : 2013 GAS METERS - ADDITIONAL FUNCTIONALITIES
    PREN 126 : DRAFT 2010 MULTIFUNCTIONAL CONTROLS FOR GAS BURNING APPLIANCES
    PREN 416 : DRAFT 2017 GAS-FIRED OVERHEAD RADIANT TUBE HEATERS AND RADIANT TUBE HEATER SYSTEMS FOR NON-DOMESTIC USE - SAFETY AND ENERGY EFFICIENCY
    10/30232407 DC : 0 BS EN 126 - MULTIFUNCTIONAL CONTROLS FOR GAS BURNING APPLIANCES
    12/30268377 DC : 0 BS EN 50156-2 - ELECTRICAL EQUIPMENT FOR FURNACES AND ANCILLARY EQUIPMENT - PART 2: REQUIREMENTS FOR DESIGN, DEVELOPMENT AND TYPE APPROVAL OF SAFETY DEVICES AND SUBSYSTEMS
    BS EN 50156-2:2015 Electrical equipment for furnaces and ancillary equipment Requirements for design, development and type approval of safety devices and subsystems
    08/30183852 DC : DRAFT AUG 2008 BS EN 1106 - MANUALLY OPERATED TAPS FOR GAS BURNING APPLIANCES
    04/30111048 DC : 0 EN 88-2 - PRESSURE GOVERNORS AND ASSOCIATED SAFETY DEVICES FOR GAS APPLIANCES - PART 2 - PRESSURE GOVERNORS FOR INLET PRESSURES BETWEEN 0.5 BAR AND 5 BAR
    12/30267815 DC : 0 BS EN 1643 - VALVE PROVING SYSTEMS FOR AUTOMATIC SHUT-OFF VALVES FOR GAS BURNERS AND GAS APPLIANCES
    17/30363953 DC : 0 BS EN 416 - GAS-FIRED OVERHEAD RADIANT TUBE HEATERS AND RADIANT TUBE HEATER SYSTEMS FOR NON-DOMESTIC USE - SAFETY AND ENERGY EFFICIENCY
    UNE-EN 16314:2014 Gas meters - Additional functionalities
    10/30216582 DC : 0 BS EN 13611:2007/A2 - SAFETY AND CONTROL DEVICES FOR GAS BURNERS AND GAS BURNING APPLIANCES - GENERAL REQUIREMENTS
    CEN/TR 16787 : 2014 INDUSTRIAL GAS INSTALLATION - GUIDELINE
    BS EN 16340 : 2014 SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS OR LIQUID FUELS - COMBUSTION PRODUCT SENSING DEVICES
    12/30254959 DC : 0 BS EN 89 - GAS-FIRED STORAGE WATER HEATERS FOR THE PRODUCTION OF DOMESTIC HOT WATER
    BS EN 16678:2015 (published 2015-11) Safety and control devices for gas burners and gas burning appliances. Automatic shut-off valves for operating pressure of above 500 kPa up to and including 6 300 kPa
    11/30246174 DC : 0 BS EN 16304 - VENT VALVES
    PREN 50156-2 : DRAFT 2012 ELECTRICAL EQUIPMENT FOR FURNACES AND ANCILLARY EQUIPMENT - PART 2: REQUIREMENTS FOR DESIGN, DEVELOPMENT AND TYPE APPROVAL OF SAFETY DEVICES AND SUBSYSTEMS
    15/30312987 DC : 0 BS EN 16830 - SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS OR LIQUID FUELS - CONTROL FUNCTIONS IN ELECTRONIC SYSTEMS - TEMPERATURE CONTROL FUNCTION
    06/30148043 DC : 0 EN 88-2 - PRESSURE REGULATORS AND ASSOCIATED SAFETY DEVICES FOR GAS APPLIANCES - PART 2: PRESSURE REGULATORS FOR INLET PRESSURES ABOVE 500 MBAR UP TO AND INCLUDING 5 BAR
    11/30249911 DC : 0 BS EN 50465 - GAS APPLIANCES - COMBINED HEAT AND POWER APPLIANCE OF NOMINAL HEAT INPUT INFERIOR OR EQUAL TO 70 KW
    10/30218092 DC : 0 BS EN 15502-1 - GAS-FIRED HEATING BOILERS - PART 1: GENERAL REQUIREMENTS AND TESTS
    UNE-EN 16830:2017 Safety and control devices for burners and appliances burning gaseous or liquid fuels - Control functions in electronic systems - Temperature Control function
    06/30149018 DC : 0 EN 15502-1 - GAS-FIRED CENTRAL HEATING BOILERS - PART 1: GENERAL REQUIREMENTS AND TESTS
    12/30257298 DC : 0 BS EN 676 - FORCED DRAUGHT BURNERS FOR GASEOUS FUELS
    PREN 17175 : DRAFT 2017 GAS-FIRED OVERHEAD RADIANT STRIP HEATERS AND MULTI-BURNER CONTINUOUS RADIANT TUBE HEATER SYSTEMS FOR NON-DOMESTIC USE - SAFETY AND ENERGY EFFICIENCY
    DIN EN 16340:2014-10 SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS OR LIQUID FUELS - COMBUSTION PRODUCT SENSING DEVICES
    12/30254956 DC : 0 BS EN 26 - GAS-FIRED INSTANTANEOUS WATER HEATERS FOR THE PRODUCTION OF DOMESTIC HOT WATER
    PREN 419 : DRAFT 2017 GAS-FIRED OVERHEAD LUMINOUS RADIANT HEATERS FOR NONDOMESTIC USE - SAFETY AND ENERGY EFFICIENCY
    10/30217314 DC : 0 BS EN 298 - AUTOMATIC BURNER CONTROL SYSTEMS FOR BURNERS AND APPLIANCES BURNING GASEOUS OR LIQUID FUELS
    DIN EN 16314:2013-09 GAS METERS - ADDITIONAL FUNCTIONALITIES
    12/30258099 DC : DRAFT MAR 2012 BS EN 267 - FORCED DRAUGHT BURNERS FOR LIQUID FUELS
    UNI EN 16304 : 2013 AUTOMATIC VENT VALVES FOR GAS BURNERS AND GAS BURNING APPLIANCES
    DIN EN 16830 : 2015 SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS OR LIQUID FUELS - CONTROL FUNCTIONS IN ELECTRONIC SYSTEMS - TEMPERATURE CONTROL FUNCTION
    BS EN 16304:2013 (published 2013-04) Automatic vent valves for gas burners and gas burning appliances
    16/30338096 DC : 0 BS EN 303-1 - HEATING BOILERS - PART 1: HEATING BOILERS WITH FORCED DRAUGHT BURNERS - TERMINOLOGY, GENERAL REQUIREMENTS, TESTING AND MARKING
    I.S. EN 50156-2:2015 ELECTRICAL EQUIPMENT FOR FURNACES AND ANCILLARY EQUIPMENT - PART 2: REQUIREMENTS FOR DESIGN, DEVELOPMENT AND TYPE APPROVAL OF SAFETY DEVICES AND SUBSYSTEMS
    PREN 676 : DRAFT 2012 FORCED DRAUGHT BURNERS FOR GASEOUS FUELS
    BS PD CEN/TR 16787 : 2014 INDUSTRIAL GAS INSTALLATION - GUIDELINE
    08/30183343 DC : DRAFT AUG 2008 BS EN 257 - MECHANICAL THERMOSTATS FOR GAS-BURNING APPLIANCES
    I.S. ENV 14459:2003 METHOD OF RISK ANALYSIS AND RECOMMENDATIONS FOR THE USE OF ELECTRONICS IN SYSTEMS FOR THE CONTROL OF GAS BURNERS AND GAS BURNING APPLIANCES
    BS PD IEC TR 62685 : 2010 INDUSTRIAL COMMUNICATION NETWORKS - PROFILES - ASSESSMENT GUIDELINE FOR SAFETY DEVICES USING IEC 61784-3 FUNCTIONAL SAFETY COMMUNICATION PROFILES (FSCPS)
    09/30204183 DC : 0 BS EN 88-1 - PRESSURE REGULATORS AND ASSOCIATED SAFETY DEVICES FOR GAS APPLIANCES - PART 1: PRESSURE REGULATORS FOR INLET PRESSURES UP TO AND INCLUDING 500 MBAR
    11/30252227 DC : 0 BS EN 16340 - COMBUSTION PRODUCT SENSING DEVICES FOR GAS BURNERS AND GAS BURNING APPLIANCES
    08/30180918 DC : DRAFT JULY 2008 BS EN 1854 - PRESSURE SENSING DEVICES FOR GAS BURNERS AND GAS BURNING APPLIANCES
    UNE-EN 14459:2016 Safety and control devices for burners and appliances burning gaseous or liquid fuels - Control functions in electronic systems - Methods for classification and assessment
    11/30243882 DC : 0 BS EN 161:2011/A1 - AUTOMATIC SHUT-OFF VALVES FOR GAS BURNERS AND GAS APPLIANCES - SPECIAL REQUIREMENTS TO DETERMINE THE PERFORMANCE LEVEL (PL)
    PREN 88-3 : DRAFT 2017 SAFETY AND CONTROL DEVICES FOR GAS BURNERS AND GAS BURNING APPLIANCES - PART 3: PRESSURE AND/OR FLOW RATE REGULATORS FOR INLET PRESSURES UP TO AND INCLUDING 500 KPA, ELECTRONIC TYPES
    BS EN 16830:2017 Safety and control devices for burners and appliances burning gaseous or liquid fuels. Control functions in electronic systems. Temperature Control function
    09/30202307 DC : 0 BS EN 12514-1 - PARTS FOR SUPPLY SYSTEMS FOR CONSUMING UNITS WITH LIQUID FUELS - PART 1: SAFETY REQUIREMENTS AND TESTS - TERMINOLOGY, GENERAL REQUIREMENTS
    BS EN 15502-1 : 2012 GAS-FIRED HEATING BOILERS - PART 1: GENERAL REQUIREMENTS AND TESTS
    UNE-EN 16340:2015 Safety and control devices for burners and appliances burning gaseous or liquid fuels - Combustion product sensing devices
    I.S. EN 16314:2013 GAS METERS - ADDITIONAL FUNCTIONALITIES
    PREN 89 : DRAFT 2012 GAS-FIRED STORAGE WATER HEATERS FOR THE PRODUCTION OF DOMESTIC HOT WATER
    08/30174305 DC : DRAFT FEB 2008 BS EN 125 - FLAME SUPERVISION DEVICES FOR GAS BURNING APPLIANCES - THERMOELECTRIC FLAME SUPERVISION DEVICES
    BS EN 50465:2015 European product standard for combined heating power systems using gas fuel
    I.S. EN 16830:2017 SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS OR LIQUID FUELS - CONTROL FUNCTIONS IN ELECTRONIC SYSTEMS - TEMPERATURE CONTROL FUNCTION
    S.R. CLC/TR 62685:2011 INDUSTRIAL COMMUNICATION NETWORKS - PROFILES - ASSESSMENT GUIDELINE FOR SAFETY DEVICES USING IEC 61784-3 FUNCTIONAL SAFETY COMMUNICATION PROFILES (FSCPS) (IEC/TR 62685:2010 (EQV))
    DIN EN 15502-1:2015-10 Gas-fired heating boilers - Part 1: General requirements and tests (includes Amendment A1:2015)
    UNI EN 16314 : 2013 GAS METERS - ADDITIONAL FUNCTIONALITIES
    DIN EN 16678:2016-02 SAFETY AND CONTROL DEVICES FOR GAS BURNERS AND GAS BURNING APPLIANCES - AUTOMATIC SHUT-OFF VALVES FOR OPERATING PRESSURE OF ABOVE 500 KPA UP TO AND INCLUDING 6300 KPA
    CEI CLC/TR 62685 : 2012 INDUSTRIAL COMMUNICATION NETWORKS - PROFILES - ASSESSMENT GUIDELINE FOR SAFETY DEVICES USING IEC 61784-3 FUNCTIONAL SAFETY COMMUNICATION PROFILES (FSCPS)
    EN 15339-2 : 2007 THERMAL SPRAYING - SAFETY REQUIREMENTS FOR THERMAL SPRAYING EQUIPMENT - PART 2: GAS CONTROL UNITS
    PREN 15502-1 : DRAFT 2010 GAS-FIRED HEATING BOILERS - PART 1: GENERAL REQUIREMENTS AND TESTS
    UNI EN 16340 : 2014 SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS OR LIQUID FUELS - COMBUSTION PRODUCT SENSING DEVICES
    PREN 303-1 : DRAFT 2016 HEATING BOILERS - PART 1: HEATING BOILERS WITH FORCED DRAUGHT BURNERS - TERMINOLOGY, GENERAL REQUIREMENTS, TESTING AND MARKING
    I.S. EN 16304:2013 AUTOMATIC VENT VALVES FOR GAS BURNERS AND GAS BURNING APPLIANCES
    I.S. EN 15339-2:2007 THERMAL SPRAYING - SAFETY REQUIREMENTS FOR THERMAL SPRAYING EQUIPMENT - PART 2: GAS CONTROL UNITS
    I.S. EN 16340:2014 SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS OR LIQUID FUELS - COMBUSTION PRODUCT SENSING DEVICES
    S.R. CEN/TR 16787:2014 INDUSTRIAL GAS INSTALLATION - GUIDELINE
    I.S. EN 15502-1:2012 GAS-FIRED HEATING BOILERS - PART 1: GENERAL REQUIREMENTS AND TESTS
    UNE-EN 16678:2016 Safety and control devices for gas burners and gas burning appliances - Automatic shut-off valves for operating pressure of above 500 kPa up to and including 6 300 kPa
    I.S. EN 16678:2015 SAFETY AND CONTROL DEVICES FOR GAS BURNERS AND GAS BURNING APPLIANCES - AUTOMATIC SHUT-OFF VALVES FOR OPERATING PRESSURE OF ABOVE 500 KPA UP TO AND INCLUDING 6300 KPA
    PREN 298 : DRAFT 2010 AUTOMATIC BURNER CONTROL SYSTEMS FOR BURNERS AND APPLIANCES BURNING GASEOUS OR LIQUID FUELS
    17/30363956 DC : 0 BS EN 419 - GAS-FIRED OVERHEAD LUMINOUS RADIANT HEATERS FOR NON-DOMESTIC USE - SAFETY AND ENERGY EFFICIENCY
    17/30363959 DC : 0 BS EN 17175 - GAS-FIRED OVERHEAD RADIANT STRIP HEATERS AND MULTI-BURNER CONTINUOUS RADIANT TUBE HEATER SYSTEMS FOR NON-DOMESTIC USE - SAFETY AND ENERGY EFFICIENCY
    CLC/TR 62685 : 2011 INDUSTRIAL COMMUNICATION NETWORKS - PROFILES - ASSESSMENT GUIDELINE FOR SAFETY DEVICES USING IEC 61784-3 FUNCTIONAL SAFETY COMMUNICATION PROFILES (FSCPS) (IEC/TR 62685:2010)
    ISO 13577-2:2014 Industrial furnaces and associated processing equipment Safety Part 2: Combustion and fuel handling systems
    05/30135987 DC : 0 EN 161 - AUTOMATIC SHUT-OFF VALVES FOR GAS BURNERS AND GAS APPLIANCES
    BS EN 16475-2:2017 (published 2017-04) Chimneys. Accessories Chimney fans. Requirements and test methods
    17/30356713 DC : DRAFT SEP 2017 BS EN 88-3 - SAFETY AND CONTROL DEVICES FOR GAS BURNERS AND GAS BURNING APPLIANCES - PART 3: PRESSURE AND/OR FLOW RATE REGULATORS FOR INLET PRESSURES UP TO AND INCLUDING 500 KPA, ELECTRONIC TYPES
    13/30286091 DC : 0 BS EN 16678 - SAFETY AND CONTROL DEVICES FOR GAS BURNERS AND GAS BURNING APPLIANCES - AUTOMATIC SHUT-OFF VALVES FOR OPERATING PRESSURE OF ABOVE 500 KPA UP TO AND INCLUDING 6300 KPA
    BS PD CLC/TR 62685 : 2011 INDUSTRIAL COMMUNICATION NETWORKS - PROFILES - ASSESSMENT GUIDELINE FOR SAFETY DEVICES USING IEC 61784-3 FUNCTIONAL SAFETY COMMUNICATION PROFILES (FSCPS)
    PREN 26 : DRAFT 2012 GAS-FIRED INSTANTANEOUS WATER HEATERS FOR THE PRODUCTION OF DOMESTIC HOT WATER
    PREN 50465 : DRAFT 2011 GAS APPLIANCES - COMBINED HEAT AND POWER APPLIANCE OF NOMINAL HEAT INPUT INFERIOR OR EQUAL TO 70 KW
    UNE-EN 16304:2013 Automatic vent valves for gas burners and gas burning appliances
    15/30311432 DC : 0 BS EN WI 16898 - SAFETY AND CONTROL DEVICES FOR GAS BURNERS AND GAS BURNING APPLIANCES - GAS FILTERS HAVING A MAXIMUM WORKING PRESSURE UP TO AND INCLUDING 600 KPA
    EN 50465 : 2015 GAS APPLIANCES - COMBINED HEAT AND POWER APPLIANCE OF NOMINAL HEAT INPUT INFERIOR OR EQUAL TO 70 KW
    IEC TR 62685:2010 Industrial communication networks - Profiles - Assessment guideline for safety devices using IEC 61784-3 functional safety communication profiles (FSCPs)
    I.S. EN 50465:2015 GAS APPLIANCES - COMBINED HEAT AND POWER APPLIANCE OF NOMINAL HEAT INPUT INFERIOR OR EQUAL TO 70 KW
    EN 267:2009+A1:2011 AUTOMATIC FORCED DRAUGHT BURNERS FOR LIQUID FUELS
    EN 676:2003+A2:2008/AC:2008 AUTOMATIC FORCED DRAUGHT BURNERS FOR GASEOUS FUELS
    I.S. EN 676:2003 AUTOMATIC FORCED DRAUGHT BURNERS FOR GASEOUS FUELS
    I.S. EN 267:2009 AUTOMATIC FORCED DRAUGHT BURNERS FOR LIQUID FUELS
    BS EN 267 : 2009 AUTOMATIC FORCED DRAUGHT BURNERS FOR LIQUID FUELS
    DIN EN 1106:2010-09 Manually operated taps for gas burning appliances
    DIN EN 89:2015-08 GAS-FIRED STORAGE WATER HEATERS FOR THE PRODUCTION OF DOMESTIC HOT WATER
    DIN EN 1643:2014-09 SAFETY AND CONTROL DEVICES FOR GAS BURNERS AND GAS BURNING APPLIANCES - VALVE PROVING SYSTEMS FOR AUTOMATIC SHUT-OFF VALVES
    DIN EN 26:2015-08 GAS-FIRED INSTANTANEOUS WATER HEATERS FOR THE PRODUCTION OF DOMESTIC HOT WATER
    DIN EN 88-1:2016-06 PRESSURE REGULATORS AND ASSOCIATED SAFETY DEVICES FOR GAS APPLIANCES - PART 1: PRESSURE REGULATORS FOR INLET PRESSURES UP TO AND INCLUDING 50 KPA
    DIN EN 88-2:2008-03 Pressure regulators and associated safety devices for gas appliances - Part 2: Pressure regulators for inlet pressures above 500 mbar up to and including 5 bar
    DIN EN 126:2012-06 MULTIFUNCTIONAL CONTROLS FOR GAS BURNING APPLIANCES
    DIN EN 161:2013-04 Automatic shut-off valves for gas burners and gas appliances (includes Amendment A3:2013)
    DIN EN 125:2016-01 FLAME SUPERVISION DEVICES FOR GAS BURNING APPLIANCES - THERMOELECTRIC FLAME SUPERVISION DEVICES
    DIN EN 14459 E : 2016 SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS OR LIQUID FUELS - CONTROL FUNCTIONS IN ELECTRONIC SYSTEMS - METHODS FOR CLASSIFICATION AND ASSESSMENT
    DIN EN 14543 E : 2017 SPECIFICATION FOR DEDICATED LIQUEFIED PETROLEUM GAS APPLIANCES - PARASOL PATIO HEATERS - FLUELESS RADIANT HEATERS FOR OUTDOOR OR AMPLY VENTILATED AREA USE
    DIN EN 14459:2016-02 SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS OR LIQUID FUELS - CONTROL FUNCTIONS IN ELECTRONIC SYSTEMS - METHODS FOR CLASSIFICATION AND ASSESSMENT
    DIN EN 267:2011-11 Automatic forced draught burners for liquid fuels
    BS EN 257:2010 (published 2010-07) Mechanical thermostats for gas-burning appliances
    UNE-EN 298:2013 Automatic burner control systems for burners and appliances burning gaseous or liquid fuels
    BS EN 14543:2017 (published 2017-07) Specification for dedicated liquefied petroleum gas appliances. Parasol patio heaters. Flueless radiant heaters for outdoor or amply ventilated area use
    BS EN 14459:2015 SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS OR LIQUID FUELS - CONTROL FUNCTIONS IN ELECTRONIC SYSTEMS - METHODS FOR CLASSIFICATION AND ASSESSMENT
    BS EN 126 : 2012 MULTIFUNCTIONAL CONTROLS FOR GAS BURNING APPLIANCES
    BS EN 89 : 2015 GAS-FIRED STORAGE WATER HEATERS FOR THE PRODUCTION OF DOMESTIC HOT WATER
    BS EN 1106:2001 MANUALLY OPERATED TAPS FOR GAS BURNING APPLIANCES
    BS EN 161 : 2011 AUTOMATIC SHUT-OFF VALVES FOR GAS BURNERS AND GAS APPLIANCES
    BS EN 26:1998 Gas fired instantaneous water heaters for the production of domestic hot water, fitted with atmospheric burners
    BS EN 88-2:2007 (published 2007-12) Pressure regulators and associated safety devices for gas appliances Pressure regulators for inlet pressures above 500 mbar up to and including 5 bar
    BS EN 303-1:2017 HEATING BOILERS - PART 1: HEATING BOILERS WITH FORCED DRAUGHT BURNERS - TERMINOLOGY, GENERAL REQUIREMENTS, TESTING AND MARKING
    BS EN 88-1 : 2011 PRESSURE REGULATORS AND ASSOCIATED SAFETY DEVICES FOR GAS APPLIANCES - PART 1: PRESSURE REGULATORS FOR INLET PRESSURES UP TO AND INCLUDING 50 KPA
    BS EN 12067-2:2004 (published 2004-04) Gas/air ratio controls for gas burners and gas burning appliances Electronic types
    BS EN 15339-2:2007 THERMAL SPRAYING - SAFETY REQUIREMENTS FOR THERMAL SPRAYING EQUIPMENT - PART 2: GAS CONTROL UNITS
    BS EN 1854:2010 (published 2010-08) Pressure sensing devices for gas burners and gas burning appliances
    BS EN 1643:2014 (published 2014-03) Safety and control devices for gas burners and gas burning appliances. Valve proving systems for automatic shut-off valves
    BS EN 676 : 2003 AUTOMATIC FORCED DRAUGHT BURNERS FOR GASEOUS FUELS
    BS EN 298:2012 (published 2012-07) Automatic burner control systems for burners and appliances burning gaseous or liquid fuels
    UNE-EN 1643:2014 Safety and control devices for gas burners and gas burning appliances - Valve proving systems for automatic shut-off valves
    UNE-EN 14543:2006 Specification for dedicated liquefied petroleum gas appliances - Parasol patio heaters - Flueless radiant heaters for outdoor or amply ventilated area use
    UNE-EN 89:2016 Gas-fired storage water heaters for the production of domestic hot water
    BS ISO 13577-2:2014 (published 2014-09) Industrial furnaces and associated processing equipment. Safety Combustion and fuel handling systems
    UNE-EN 126:2012 Multifunctional controls for gas burning appliances
    BS EN 125 : 2010 FLAME SUPERVISION DEVICES FOR GAS BURNING APPLIANCES - THERMOELECTRIC FLAME SUPERVISION DEVICES
    DIN EN 676:2008-11 Automatic forced draught burners for gaseous fuels (includes Amendment A2:2008)
    UNI EN 267 : 2011 AUTOMATIC FORCED DRAUGHT BURNERS FOR LIQUID FUELS
    DIN EN 12067-2:2004-06 Gas/air ratio controls for gas burners and gas burning appliances - Part 2: Electronic types
    I.S. EN 1643:2014 SAFETY AND CONTROL DEVICES FOR GAS BURNERS AND GAS BURNING APPLIANCES - VALVE PROVING SYSTEMS FOR AUTOMATIC SHUT-OFF VALVES
    I.S. EN 1854:2010 PRESSURE SENSING DEVICES FOR GAS BURNERS AND GAS BURNING APPLIANCES
    DIN EN 1643:2001-02 SAFETY AND CONTROL DEVICES FOR GAS BURNERS AND GAS BURNING APPLIANCES - VALVE PROVING SYSTEMS FOR AUTOMATIC SHUT-OFF VALVES
    I.S. EN 161:2011 AUTOMATIC SHUT-OFF VALVES FOR GAS BURNERS AND GAS APPLIANCES
    I.S. EN 1106:2010 MANUALLY OPERATED TAPS FOR GAS BURNING APPLIANCES
    I.S. EN 125:2010 FLAME SUPERVISION DEVICES FOR GAS BURNING APPLIANCES - THERMOELECTRIC FLAME SUPERVISION DEVICES
    I.S. EN 14543:2017 SPECIFICATION FOR DEDICATED LIQUEFIED PETROLEUM GAS APPLIANCES - PARASOL PATIO HEATERS - FLUELESS RADIANT HEATERS FOR OUTDOOR OR AMPLY VENTILATED AREA USE
    I.S. EN 26:2015 GAS-FIRED INSTANTANEOUS WATER HEATERS FOR THE PRODUCTION OF DOMESTIC HOT WATER
    I.S. EN 14459:2015 SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS OR LIQUID FUELS - CONTROL FUNCTIONS IN ELECTRONIC SYSTEMS - METHODS FOR CLASSIFICATION AND ASSESSMENT
    DIN EN 1854:2010-10 Pressure sensing devices for gas burners and gas burning appliances
    I.S. EN 126:2012 MULTIFUNCTIONAL CONTROLS FOR GAS BURNING APPLIANCES
    I.S. EN 298:2012 AUTOMATIC BURNER CONTROL SYSTEMS FOR BURNERS AND APPLIANCES BURNING GASEOUS OR LIQUID FUELS
    I.S. EN 88-1:2011 PRESSURE REGULATORS AND ASSOCIATED SAFETY DEVICES FOR GAS APPLIANCES - PART 1: PRESSURE REGULATORS FOR INLET PRESSURES UP TO AND INCLUDING 50 KPA
    I.S. EN 257:2010 MECHANICAL THERMOSTATS FOR GAS-BURNING APPLIANCES
    I.S. EN 303-1:2017 HEATING BOILERS - PART 1: HEATING BOILERS WITH FORCED DRAUGHT BURNERS - TERMINOLOGY, GENERAL REQUIREMENTS, TESTING AND MARKING
    DIN EN 15339-2:2007-06 Thermal spraying - Safety requirements for thermal spraying equipment - Part 2: Gas control units
    I.S. EN 89:2015 GAS-FIRED STORAGE WATER HEATERS FOR THE PRODUCTION OF DOMESTIC HOT WATER
    EN 12067-2 : 2004 GAS/AIR RATIO CONTROLS FOR GAS BURNERS AND GAS BURNING APPLIANCES - PART 2: ELECTRONIC TYPES
    DIN EN 14543:2017-10 SPECIFICATION FOR DEDICATED LIQUEFIED PETROLEUM GAS APPLIANCES - PARASOL PATIO HEATERS - FLUELESS RADIANT HEATERS FOR OUTDOOR OR AMPLY VENTILATED AREA USE
    EN 88-1:2011+A1:2016 PRESSURE REGULATORS AND ASSOCIATED SAFETY DEVICES FOR GAS APPLIANCES - PART 1: PRESSURE REGULATORS FOR INLET PRESSURES UP TO AND INCLUDING 50 KPA
    EN 126 : 2012 MULTIFUNCTIONAL CONTROLS FOR GAS BURNING APPLIANCES
    EN 16830 : 2017 SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS OR LIQUID FUELS - CONTROL FUNCTIONS IN ELECTRONIC SYSTEMS - TEMPERATURE CONTROL FUNCTION
    EN 14459 : 2015 SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS OR LIQUID FUELS - CONTROL FUNCTIONS IN ELECTRONIC SYSTEMS - METHODS FOR CLASSIFICATION AND ASSESSMENT
    EN 15502-1:2012+A1:2015 GAS-FIRED HEATING BOILERS - PART 1: GENERAL REQUIREMENTS AND TESTS
    EN 50156-2 : 2015 ELECTRICAL EQUIPMENT FOR FURNACES AND ANCILLARY EQUIPMENT - PART 2: REQUIREMENTS FOR DESIGN, DEVELOPMENT AND TYPE APPROVAL OF SAFETY DEVICES AND SUBSYSTEMS
    EN 1106 : 2010 MANUALLY OPERATED TAPS FOR GAS BURNING APPLIANCES
    DIN EN 257:2010-11 Mechanical thermostats for gas-burning appliances
    EN 89 : 2015 GAS-FIRED STORAGE WATER HEATERS FOR THE PRODUCTION OF DOMESTIC HOT WATER
    EN 16304 : 2013 AUTOMATIC VENT VALVES FOR GAS BURNERS AND GAS BURNING APPLIANCES
    EN 14543 : 2017 SPECIFICATION FOR DEDICATED LIQUEFIED PETROLEUM GAS APPLIANCES - PARASOL PATIO HEATERS - FLUELESS RADIANT HEATERS FOR OUTDOOR OR AMPLY VENTILATED AREA USE
    EN 16340 : 2014 SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS OR LIQUID FUELS - COMBUSTION PRODUCT SENSING DEVICES
    EN 298 : 2012 AUTOMATIC BURNER CONTROL SYSTEMS FOR BURNERS AND APPLIANCES BURNING GASEOUS OR LIQUID FUELS
    EN 16678 : 2015 SAFETY AND CONTROL DEVICES FOR GAS BURNERS AND GAS BURNING APPLIANCES - AUTOMATIC SHUT-OFF VALVES FOR OPERATING PRESSURE OF ABOVE 500 KPA UP TO AND INCLUDING 6300 KPA
    EN 161:2011+A3:2013 AUTOMATIC SHUT-OFF VALVES FOR GAS BURNERS AND GAS APPLIANCES
    EN 1854 : 2010 PRESSURE SENSING DEVICES FOR GAS BURNERS AND GAS BURNING APPLIANCES
    EN 16314 : 2013 GAS METERS - ADDITIONAL FUNCTIONALITIES
    EN 26 : 2015 GAS-FIRED INSTANTANEOUS WATER HEATERS FOR THE PRODUCTION OF DOMESTIC HOT WATER
    EN 303-1 : 2017 HEATING BOILERS - PART 1: HEATING BOILERS WITH FORCED DRAUGHT BURNERS - TERMINOLOGY, GENERAL REQUIREMENTS, TESTING AND MARKING
    EN 16475-2 : 2017 CHIMNEYS - ACCESSORIES - PART 2: CHIMNEY FANS - REQUIREMENTS AND TEST METHODS
    EN 125:2010+A1:2015 FLAME SUPERVISION DEVICES FOR GAS BURNING APPLIANCES - THERMOELECTRIC FLAME SUPERVISION DEVICES
    EN 257 : 2010 MECHANICAL THERMOSTATS FOR GAS-BURNING APPLIANCES
    EN 88-2 : 2007 PRESSURE REGULATORS AND ASSOCIATED SAFETY DEVICES FOR GAS APPLIANCES - PART 2: PRESSURE REGULATORS FOR INLET PRESSURES ABOVE 500 MBAR UP TO AND INCLUDING 5 BAR
    EN 1643 : 2014 SAFETY AND CONTROL DEVICES FOR GAS BURNERS AND GAS BURNING APPLIANCES - VALVE PROVING SYSTEMS FOR AUTOMATIC SHUT-OFF VALVES

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 61508-6 : 2010 FUNCTIONAL SAFETY OF ELECTRICAL/ELECTRONIC/PROGRAMMABLE ELECTRONIC SAFETY-RELATED SYSTEMS - PART 6: GUIDELINES ON THE APPLICATION OF IEC 61508-2 AND IEC 61508-3
    EN 10293 : 2015 STEEL CASTINGS - STEEL CASTINGS FOR GENERAL ENGINEERING USES
    ISO 898-2:2012 Mechanical properties of fasteners made of carbon steel and alloy steel Part 2: Nuts with specified property classes Coarse thread and fine pitch thread
    EN 61508-3 : 2010 FUNCTIONAL SAFETY OF ELECTRICAL/ELECTRONIC/PROGRAMMABLE ELECTRONIC SAFETY-RELATED SYSTEMS - PART 3: SOFTWARE REQUIREMENTS
    ISO 9606-4:1999 Approval testing of welders Fusion welding Part 4: Nickel and nickel alloys
    ISO 7005-2:1988 Metallic flanges Part 2: Cast iron flanges
    EN 60747-5-2:2001/A1:2002 DISCRETE SEMICONDUCTOR DEVICES AND INTEGRATED CIRCUITS - PART 5-2: OPTOELECTRONIC DEVICES - ESSENTIAL RATINGS AND CHARACTERISTICS
    EN 61558-2-16:2009/A1:2013 SAFETY OF TRANSFORMERS, REACTORS, POWER SUPPLY UNITS AND SIMILAR PRODUCTS FOR SUPPLY VOLTAGES UP TO 1 100 V - PART 2-16: PARTICULAR REQUIREMENTS AND TESTS FOR SWITCH MODE POWER SUPPLY UNITS AND TRANSFORMERS FOR SWITCH MODE POWER SUPPLY UNITS (IEC 61558-2-16:2009/A1:2013)
    ISO 9606-2:2004 Qualification test of welders Fusion welding Part 2: Aluminium and aluminium alloys
    IEC 60384-14:2013+AMD1:2016 CSV Fixed capacitors for use in electronic equipment - Part 14: Sectional specification - Fixed capacitors for electromagnetic interference suppression and connection to the supply mains
    ISO 8434-1:2007 Metallic tube connections for fluid power and general use Part 1: 24 degree cone connectors
    IEC 60191-1:2007 Mechanical standardization of semiconductor devices - Part 1: General rules for the preparation of outline drawings of discrete devices
    ISO 3506-1:2009 Mechanical properties of corrosion-resistant stainless steel fasteners Part 1: Bolts, screws and studs
    EN 61508-1 : 2010 FUNCTIONAL SAFETY OF ELECTRICAL/ELECTRONIC/PROGRAMMABLE ELECTRONIC SAFETY-RELATED SYSTEMS - PART 1: GENERAL REQUIREMENTS
    EN 10226-2 : 2005 PIPE THREADS WHERE PRESSURE TIGHT JOINTS ARE MADE ON THE THREADS - PART 2: TAPER EXTERNAL THREADS AND TAPER INTERNAL THREADS - DIMENSIONS, TOLERANCES AND DESIGNATION
    EN 746-2 : 2010 INDUSTRIAL THERMOPROCESSING EQUIPMENT - PART 2: SAFETY REQUIREMENTS FOR COMBUSTION AND FUEL HANDLING SYSTEMS
    EN 10216-5 : 2013 SEAMLESS STEEL TUBES FOR PRESSURE PURPOSES - TECHNICAL DELIVERY CONDITIONS - PART 5: STAINLESS STEEL TUBES
    ISO 7637-3:2016 Road vehicles Electrical disturbances from conduction and coupling Part 3: Electrical transient transmission by capacitive and inductive coupling via lines other than supply lines
    EN 10213:2007+A1:2016 STEEL CASTINGS FOR PRESSURE PURPOSES
    EN ISO 15613 : 2004 SPECIFICATION AND QUALIFICATION OF WELDING PROCEDURES FOR METALLIC MATERIALS - QUALIFICATION BASED ON PRE-PRODUCTION WELDING TEST
    EN 10028-3 : 2017 FLAT PRODUCTS MADE OF STEELS FOR PRESSURE PURPOSES - PART 3: WELDABLE FINE GRAIN STEELS, NORMALIZED
    ISO 15614-2:2005 Specification and qualification of welding procedures for metallic materials Welding procedure test Part 2: Arc welding of aluminium and its alloys
    ISO 9712:2012 Non-destructive testing Qualification and certification of NDT personnel
    EN 13906-1 : 2013 CYLINDRICAL HELICAL SPRINGS MADE FROM ROUND WIRE AND BARS - CALCULATION AND DESIGN - PART 1: COMPRESSION SPRINGS
    EN 61508-7 : 2010 FUNCTIONAL SAFETY OF ELECTRICAL/ELECTRONIC/PROGRAMMABLE ELECTRONIC SAFETY-RELATED SYSTEMS - PART 7: OVERVIEW OF TECHNIQUES AND MEASURES
    EN 12067-2 : 2004 GAS/AIR RATIO CONTROLS FOR GAS BURNERS AND GAS BURNING APPLIANCES - PART 2: ELECTRONIC TYPES
    EN ISO 3506-1 : 2009 MECHANICAL PROPERTIES OF CORROSION-RESISTANT STAINLESS STEEL FASTENERS - PART 1: BOLTS, SCREWS AND STUDS
    EN 1057:2006+A1:2010 COPPER AND COPPER ALLOYS - SEAMLESS, ROUND COPPER TUBES FOR WATER AND GAS IN SANITARY AND HEATING APPLICATIONS
    EN ISO 15612 : 2004 SPECIFICATION AND QUALIFICATION OF WELDING PROCEDURES FOR METALLIC MATERIALS - QUALIFICATION BY ADOPTION OF A STANDARD WELDING PROCEDURE
    ISO 15610:2003 Specification and qualification of welding procedures for metallic materials Qualification based on tested welding consumables
    EN ISO 3506-3 : 2009 MECHANICAL PROPERTIES OF CORROSION-RESISTANT STAINLESS STEEL FASTENERS - PART 3: SET SCREWS AND SIMILAR FASTENERS NOT UNDER TENSILE STRESS (ISO 3506-3:2009)
    EN 1643 : 2014 SAFETY AND CONTROL DEVICES FOR GAS BURNERS AND GAS BURNING APPLIANCES - VALVE PROVING SYSTEMS FOR AUTOMATIC SHUT-OFF VALVES
    ISO 23529:2016 Rubber General procedures for preparing and conditioning test pieces for physical test methods
    ASTM F 593 : 2017 : REDLINE Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs
    ISO 14732:2013 Welding personnel Qualification testing of welding operators and weld setters for mechanized and automatic welding of metallic materials
    EN 485-2 : 2016 ALUMINIUM AND ALUMINIUM ALLOYS - SHEET, STRIP AND PLATE - PART 2: MECHANICAL PROPERTIES
    ISO 815-1:2014 Rubber, vulcanized or thermoplastic Determination of compression set Part 1: At ambient or elevated temperatures
    EN 10028-6 : 2017 FLAT PRODUCTS MADE OF STEELS FOR PRESSURE PURPOSES - PART 6: WELDABLE FINE GRAIN STEELS, QUENCHED AND TEMPERED
    EN 60127-1:2006/A2:2015 MINIATURE FUSES - PART 1: DEFINITIONS FOR MINIATURE FUSES AND GENERAL REQUIREMENTS FOR MINIATURE FUSE-LINKS
    ISO 1083:2004 Spheroidal graphite cast irons - Classification
    IEC 60050-441:1984 International Electrotechnical Vocabulary (IEV) - Part 441: Switchgear, controlgear and fuses
    ASTM A 395/A395M : 1999 Standard Specification for Ferritic Ductile Iron Pressure-Retaining Castings for Use at Elevated Temperatures
    SAE J 429 : 2014 MECHANICAL AND MATERIAL REQUIREMENTS FOR EXTERNALLY THREADED FASTENERS
    EN 10088-3 : 2014 Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes
    ISO 7637-2:2011 Road vehicles Electrical disturbances from conduction and coupling Part 2: Electrical transient conduction along supply lines only
    EN 10111 : 2008 CONTINUOUSLY HOT ROLLED LOW CARBON STEEL SHEET AND STRIP FOR COLD FORMING - TECHNICAL DELIVERY CONDITIONS
    EN 10087 : 1998 FREE-CUTTING STEELS - TECHNICAL DELIVERY CONDITIONS FOR SEMI-FINISHED PRODUCTS, HOT ROLLED BARS AND RODS
    ASTM A 516/A516M : 2017 : REDLINE Standard Specification for Pressure Vessel Plates, Carbon Steel, for Moderate- and Lower-Temperature Service
    IEC 61558-2-16:2009+AMD1:2013 CSV Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-16: Particularrequirements and tests for switch mode power supply units andtransformers for switch mode power supply units
    ISO 7005-3:1988 Metallic flanges Part 3: Copper alloy and composite flanges
    EN 586-2 : 1994 ALUMINIUM AND ALUMINIUM ALLOYS - FORGINGS - MECHANICAL PROPERTIES AND ADDITIONAL PROPERTY REQUIREMENTS
    IEC 60947-5-1 : 4.0 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 5-1: CONTROL CIRCUIT DEVICES AND SWITCHING ELEMENTS - ELECTROMECHANICAL CONTROL CIRCUIT DEVICES
    ASTM B 584 : 2014 : REDLINE Standard Specification for Copper Alloy Sand Castings for General Applications
    ISO 9606-1:2012 Qualification testing of welders Fusion welding Part 1: Steels
    EN 12516-1 : 2014 INDUSTRIAL VALVES - SHELL DESIGN STRENGTH - PART 1: TABULATION METHOD FOR STEEL VALVE SHELLS
    EN 10346 : 2015 CONTINUOUSLY HOT-DIP COATED STEEL FLAT PRODUCTS FOR COLD FORMING - TECHNICAL DELIVERY CONDITIONS
    EN ISO 9606-4 : 1999 APPROVAL TESTING OF WELDERS - FUSION WELDING - PART 4: NICKEL AND NICKEL ALLOYS
    IEC 61508-4:2010 Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 4: Definitions and abbreviations (see Functional Safety and IEC 61508)
    EN 88-2 : 2007 PRESSURE REGULATORS AND ASSOCIATED SAFETY DEVICES FOR GAS APPLIANCES - PART 2: PRESSURE REGULATORS FOR INLET PRESSURES ABOVE 500 MBAR UP TO AND INCLUDING 5 BAR
    IEC 61810-1:2015 Electromechanical elementary relays - Part 1: General and safety requirements
    IEC 61508-3:2010 Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 3: Software requirements (see Functional Safety and IEC 61508)
    EN 10025-1 : 2004 HOT ROLLED PRODUCTS OF STRUCTURAL STEELS - PART 1: GENERAL TECHNICAL DELIVERY CONDITIONS
    IEC 60747-5-2:1997+AMD1:2002 CSV Discrete semiconductor devices and integrated circuits - Part 5-2: Optoelectronic devices - Essential ratings and characteristics
    EN 161:2011+A3:2013 AUTOMATIC SHUT-OFF VALVES FOR GAS BURNERS AND GAS APPLIANCES
    ISO 12100:2010 Safety of machinery General principles for design Risk assessment and risk reduction
    API 5L : 2012 LINE PIPE
    EN 60947-1:2007/A2:2014 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 1: GENERAL RULES (IEC 60947-1:2007/A2:2014)
    EN 10277-3 : 2008 BRIGHT STEEL PRODUCTS - TECHNICAL DELIVERY CONDITIONS - PART 3: FREE-CUTTING STEELS
    EN 10028-2 : 2017 FLAT PRODUCTS MADE OF STEELS FOR PRESSURE PURPOSES - PART 2: NON-ALLOY AND ALLOY STEELS WITH SPECIFIED ELEVATED TEMPERATURE PROPERTIES
    EN ISO 9712 : 2012 NON-DESTRUCTIVE TESTING - QUALIFICATION AND CERTIFICATION OF NDT PERSONNEL (ISO 9712:2012)
    EN 12020-2:2016/AC:2017 ALUMINIUM AND ALUMINIUM ALLOYS - EXTRUDED PRECISION PROFILES IN ALLOYS EN AW-6060 AND EN AW-6063 - PART 2: TOLERANCES ON DIMENSIONS AND FORM
    EN 10305-1 : 2016 STEEL TUBES FOR PRECISION APPLICATIONS - TECHNICAL DELIVERY CONDITIONS - PART 1: SEAMLESS COLD DRAWN TUBES
    EN 10028-7 : 2016 FLAT PRODUCTS MADE OF STEELS FOR PRESSURE PURPOSES - PART 7: STAINLESS STEELS
    ISO 148-1:2016 Metallic materials Charpy pendulum impact test Part 1: Test method
    ISO 23553-1:2014 Safety and control devices for oil burners and oil-burning appliances Particular requirements Part 1: Automatic and semi-automatic valves
    EN 16340 : 2014 SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS OR LIQUID FUELS - COMBUSTION PRODUCT SENSING DEVICES
    ISO 15612:2004 Specification and qualification of welding procedures for metallic materials Qualification by adoption of a standard welding procedure
    EN 1774 : 1997 ZINC AND ZINC ALLOYS - ALLOYS FOR FOUNDRY PURPOSES - INGOT AND LIQUID
    EN ISO 15611 : 2003 SPECIFICATION AND QUALIFICATION OF WELDING PROCEDURES FOR METALLIC MATERIALS - QUALIFICATION BASED ON PREVIOUS WELDING EXPERIENCE
    EN 1854 : 2010 PRESSURE SENSING DEVICES FOR GAS BURNERS AND GAS BURNING APPLIANCES
    EN ISO 228-1 : 2003 PIPE THREADS WHERE PRESSURE-TIGHT JOINTS ARE NOT MADE ON THE THREADS - PART 1: DIMENSIONS, TOLERANCES AND DESIGNATION
    ASTM A 420/A420M : 2016 : REDLINE Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Low-Temperature Service
    ISO 15614-1:2017 Specification and qualification of welding procedures for metallic materials Welding procedure test Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys
    ISO 3506-3:2009 Mechanical properties of corrosion-resistant stainless steel fasteners Part 3: Set screws and similar fasteners not under tensile stress
    EN 10305-4 : 2016 STEEL TUBES FOR PRECISION APPLICATIONS - TECHNICAL DELIVERY CONDITIONS - PART 4: SEAMLESS COLD DRAWN TUBES FOR HYDRAULIC AND PNEUMATIC POWER SYSTEMS
    EN 13906-2 : 2013 CYLINDRICAL HELICAL SPRINGS MADE FROM ROUND WIRE AND BAR - CALCULATION AND DESIGN - PART 2: EXTENSION SPRINGS
    EN 13445-4 : 2014 COR 2017 UNFIRED PRESSURE VESSELS - PART 4: FABRICATION
    ISO 262:1998 ISO general purpose metric screw threads Selected sizes for screws, bolts and nuts
    EN 14459 : 2015 SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS OR LIQUID FUELS - CONTROL FUNCTIONS IN ELECTRONIC SYSTEMS - METHODS FOR CLASSIFICATION AND ASSESSMENT
    EN 61508-2 : 2010 FUNCTIONAL SAFETY OF ELECTRICAL/ELECTRONIC/PROGRAMMABLE ELECTRONIC SAFETY-RELATED SYSTEMS - PART 2: REQUIREMENTS FOR ELECTRICAL/ELECTRONIC/PROGRAMMABLE ELECTRONIC SAFETY-RELATED SYSTEMS
    EN 10272 : 2016 STAINLESS STEEL BARS FOR PRESSURE PURPOSES
    ISO/IEC Guide 51:2014 Safety aspects Guidelines for their inclusion in standards
    EN 12279:2000/A1:2005 GAS SUPPLY SYSTEMS - GAS PRESSURE REGULATING INSTALLATIONS ON SERVICE LINES - FUNCTIONAL REQUIREMENTS
    EN 10028-5 : 2017 FLAT PRODUCTS MADE OF STEELS FOR PRESSURE PURPOSES - PART 5: WELDABLE FINE GRAIN STEELS, THERMOMECHANICALLY ROLLED
    ISO 15609-1:2004 Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 1: Arc welding
    EN ISO 17637 : 2016 NON-DESTRUCTIVE TESTING OF WELDS - VISUAL TESTING OF FUSION-WELDED JOINTS (ISO 17637:2016)
    ISO 15611:2003 Specification and qualification of welding procedures for metallic materials Qualification based on previous welding experience
    EN 437:2003+A1:2009 TEST GASES - TEST PRESSURES - APPLIANCE CATEGORIES
    EN 125:2010+A1:2015 FLAME SUPERVISION DEVICES FOR GAS BURNING APPLIANCES - THERMOELECTRIC FLAME SUPERVISION DEVICES
    EN 1706 : 2010 ALUMINIUM AND ALUMINIUM ALLOYS - CASTINGS - CHEMICAL COMPOSITION AND MECHANICAL PROPERTIES
    EN 10222-5 : 2017 STEEL FORGINGS FOR PRESSURE PURPOSES - PART 5: MARTENSITIC, AUSTENITIC AND AUSTENITIC-FERRITIC STAINLESS STEELS
    EN 10250-4 : 1999 OPEN DIE STEEL FORGINGS FOR GENERAL ENGINEERING PURPOSES - PART 4: STAINLESS STEELS
    IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
    EN 126 : 2012 MULTIFUNCTIONAL CONTROLS FOR GAS BURNING APPLIANCES
    EN 12516-3:2002/AC:2003 VALVES - SHELL DESIGN STRENGTH - PART 3: EXPERIMENTAL METHOD
    EN ISO 15614-2 : 2005 SPECIFICATION AND QUALIFICATION OF WELDING PROCEDURES FOR METALLIC MATERIALS - WELDING PROCEDURE TEST - PART 2: ARC WELDING OF ALUMINIUM AND ITS ALLOYS
    EN 10250-1 : 1999 OPEN DIE STEEL FORGINGS FOR GENERAL ENGINEERING PURPOSES - PART 1: GENERAL REQUIREMENTS
    IEC 60947-1:2007+AMD1:2010+AMD2:2014 CSV Low-voltage switchgear and controlgear - Part 1: General rules
    EN ISO 9606-2 : 2004 QUALIFICATION TEST OF WELDERS - FUSION WELDING - PART 2: ALUMINIUM AND ALUMINIUM ALLOYS
    EN 1559-1 : 2011 FOUNDING - TECHNICAL CONDITIONS OF DELIVERY - PART 1: GENERAL
    EN 334:2005+A1:2009 GAS PRESSURE REGULATORS FOR INLET PRESSURES UP TO 100 BAR
    EN 10250-2 : 1999 OPEN DIE STEEL FORGINGS FOR GENERAL ENGINEERING PURPOSES - PART 2: - NON-ALLOY QUALITY AND SPECIAL STEELS
    EN 62061:2005/A2:2015 SAFETY OF MACHINERY - FUNCTIONAL SAFETY OF SAFETY-RELATED ELECTRICAL, ELECTRONIC AND PROGRAMMABLE ELECTRONIC CONTROL SYSTEMS (IEC 62061:2005/A2:2015)
    IEC 61643-11:2011 Low-voltage surge protective devices - Part 11: Surge protective devices connected to low-voltage power systems - Requirements and test methods
    ASTM A 217/A217M : 2014 : REDLINE Standard Specification for Steel Castings, Martensitic Stainless and Alloy, for Pressure-Containing Parts, Suitable for High-Temperature Service
    ISO 17637:2016 Non-destructive testing of welds Visual testing of fusion-welded joints
    EN 1563 : 2011 FOUNDING - SPHEROIDAL GRAPHITE CAST IRONS
    EN ISO 8434-1:2007/AC:2009 METALLIC TUBE CONNECTIONS FOR FLUID POWER AND GENERAL USE - PART 1: 24 DEGREE CONE CONNECTORS
    EN ISO 15609-1 : 2004 SPECIFICATION AND QUALIFICATION OF WELDING PROCEDURES FOR METALLIC MATERIALS - WELDING PROCEDURE SPECIFICATION - PART 1: ARC WELDING
    EN 12164 : 2016 COPPER AND COPPER ALLOYS - ROD FOR FREE MACHINING PURPOSES
    EN ISO 12100 : 2010 SAFETY OF MACHINERY - GENERAL PRINCIPLES FOR DESIGN - RISK ASSESSMENT AND RISK REDUCTION
    EN 10130 : 2006 COLD ROLLED LOW CARBON STEEL FLAT PRODUCTS FOR COLD FORMING - TECHNICAL DELIVERY CONDITIONS
    EN ISO 898-1 : 2013 MECHANICAL PROPERTIES OF FASTENERS MADE OF CARBON STEEL AND ALLOY STEEL - PART 1: BOLTS, SCREWS AND STUDS WITH SPECIFIED PROPERTY CLASSES - COARSE THREAD AND FINE PITCH THREAD (ISO 898-1:2013)
    EN 10083-1 : 2006 STEELS FOR QUENCHING AND TEMPERING - PART 1: GENERAL TECHNICAL DELIVERY CONDITIONS
    EN 16304 : 2013 AUTOMATIC VENT VALVES FOR GAS BURNERS AND GAS BURNING APPLIANCES
    EN 10083-2 : 2006 STEELS FOR QUENCHING AND TEMPERING - PART 2: TECHNICAL DELIVERY CONDITIONS FOR NON ALLOY STEELS
    EN 60068-2-6 : 2008 ENVIRONMENTAL TESTING - PART 2-6: TESTS - TEST FC: VIBRATION (SINUSOIDAL)
    MSS SP 55 : 2011 QUALITY STANDARD FOR STEEL CASTINGS FOR VALVES, FLANGES, FITTINGS, AND OTHER PIPING COMPONENTS - VISUAL METHOD FOR EVALUATION OF SURFACE IRREGULARITIES
    EN ISO 13849-1 : 2015 SAFETY OF MACHINERY - SAFETY-RELATED PARTS OF CONTROL SYSTEMS - PART 1: GENERAL PRINCIPLES FOR DESIGN (ISO 13849-1:2015)
    EN 754-2 : 2016 ALUMINIUM AND ALUMINIUM ALLOYS - COLD DRAWN ROD/BAR AND TUBE - PART 2: MECHANICAL PROPERTIES
    IEC 61508-6:2010 Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 6: Guidelines on the application of IEC 61508-2 and IEC 61508-3 (see Functional Safety and IEC 61508)
    EN 61558-2-6 : 2009 SAFETY OF TRANSFORMERS, REACTORS, POWER SUPPLY UNITS AND SIMILAR PRODUCTS FOR SUPPLY VOLTAGES UP TO 1100 V - PART 2-6: PARTICULAR REQUIREMENTS AND TESTS FOR SAFETY ISOLATING TRANSFORMERS AND POWER SUPPLY UNITS INCORPORATING SAFETY ISOLATING TRANSFORMERS
    ISO 37:2017 Rubber, vulcanized or thermoplastic Determination of tensile stress-strain properties
    EN 10297-1 : 2003 SEAMLESS CIRCULAR STEEL TUBES FOR MECHANICAL AND GENERAL ENGINEERING PURPOSES - TECHNICAL DELIVERY CONDITIONS - PART 1: NON-ALLOY AND ALLOY STEEL TUBES
    EN 298 : 2012 AUTOMATIC BURNER CONTROL SYSTEMS FOR BURNERS AND APPLIANCES BURNING GASEOUS OR LIQUID FUELS
    EN 10216-1 : 2013 SEAMLESS STEEL TUBES FOR PRESSURE PURPOSES - TECHNICAL DELIVERY CONDITIONS - PART 1: NON-ALLOY STEEL TUBES WITH SPECIFIED ROOM TEMPERATURE PROPERTIES
    ISO 7005-1:2011 Pipe flanges Part 1: Steel flanges for industrial and general service piping systems
    IEC 61508-1:2010 Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 1: General requirements (see Functional Safety and IEC 61508)
    EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
    ISO 15613:2004 Specification and qualification of welding procedures for metallic materials Qualification based on pre-production welding test
    IEC 62061:2005+AMD1:2012+AMD2:2015 CSV Safety of machinery - Functional safety of safety-related electrical, electronic and programmable electronic control systems
    EN ISO 148-1 : 2016 METALLIC MATERIALS - CHARPY PENDULUM IMPACT TEST - PART 1: TEST METHOD (ISO 148-1:2016)
    EN 549 : 1994 RUBBER MATERIALS FOR SEALS AND DIAPHRAGMS FOR GAS APPLIANCES AND GAS EQUIPMENT
    ASTM A 312/A312M : 2017-03 SPECIFICATION FOR SEAMLESS, WELDED, AND HEAVILY COLD WORKED AUSTENITIC STAINLESS STEEL PIPES
    EN 1106 : 2010 MANUALLY OPERATED TAPS FOR GAS BURNING APPLIANCES
    IEC 61508-7:2010 Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 7: Overview of techniques and measures (see Functional Safety and IEC 61508)
    EN ISO 15610 : 2003 SPECIFICATION AND QUALIFICATION OF WELDING PROCEDURES FOR METALLIC MATERIALS - QUALIFICATION BASED ON TESTED WELDING CONSUMABLES
    ISO 15607:2003 Specification and qualification of welding procedures for metallic materials General rules
    EN 12165 : 2016 COPPER AND COPPER ALLOYS - WROUGHT AND UNWROUGHT FORGING STOCK
    ISO 301:2006 Zinc alloy ingots intended for castings
    IEC 61000-4-29:2000 Electromagnetic compatibility (EMC) - Part 4-29: Testing and measurement techniques - Voltage dips, short interruptions and voltage variations on d.c. input power port immunity tests
    EN ISO 9606-1 : 2017 QUALIFICATION TESTING OF WELDERS - FUSION WELDING - PART 1: STEELS (ISO 9606-1:2012 INCLUDING COR 1:2012 AND COR 2:2013)
    EN ISO 23553-1 : 2014 SAFETY AND CONTROL DEVICES FOR OIL BURNERS AND OIL-BURNING APPLIANCES - PARTICULAR REQUIREMENTS - PART 1: AUTOMATIC AND SEMI-AUTOMATIC VALVES (ISO 23553-1:2014)
    ISO 3506-2:2009 Mechanical properties of corrosion-resistant stainless steel fasteners Part 2: Nuts
    EN 10028-4 : 2017 FLAT PRODUCTS MADE OF STEELS FOR PRESSURE PURPOSES - PART 4: NICKEL ALLOY STEELS WITH SPECIFIED LOW TEMPERATURE PROPERTIES
    EN 10226-1 : 2004 PIPE THREADS WHERE PRESSURE TIGHT JOINTS ARE MADE ON THE THREADS - PART 1: TAPER EXTERNAL THREADS AND PARALLEL INTERNAL THREADS - DIMENSIONS, TOLERANCES AND DESIGNATION
    ISO 13849-1:2015 Safety of machinery Safety-related parts of control systems Part 1: General principles for design
    IEC 61508-2:2010 Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 2: Requirements for electrical/electronic/programmable electronic safety-related systems (see Functional Safety and IEC 61508)
    EN 1982 : 2017 COPPER AND COPPER ALLOYS - INGOTS AND CASTINGS
    EN 88-1:2011+A1:2016 PRESSURE REGULATORS AND ASSOCIATED SAFETY DEVICES FOR GAS APPLIANCES - PART 1: PRESSURE REGULATORS FOR INLET PRESSURES UP TO AND INCLUDING 50 KPA
    ISO 228-1:2000 Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation
    EN 1652:1997/AC:2003 COPPER AND COPPER ALLOYS - PLATE, SHEET, STRIP AND CIRCLES FOR GENERAL PURPOSES
    IEC 60384-16:2005 Fixed capacitors for use in electronic equipment - Part 16: Sectional specification: Fixed metallized polypropylene film dielectric d.c. capacitors
    EN 755-2 : 2016 ALUMINIUM AND ALUMINIUM ALLOYS - EXTRUDED ROD/BAR, TUBE AND PROFILES - PART 2: MECHANICAL PROPERTIES
    EN 61000-4-29 : 2000 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-29: TESTING AND MEASUREMENT TECHNIQUES - VOLTAGE DIPS, SHORT INTERRUPTIONS AND VOLTAGE VARIATIONS ON D.C. INPUT POWER PORT IMMUNITY TESTS
    EN ISO 15607 : 2003 SPECIFICATION AND QUALIFICATION OF WELDING PROCEDURES FOR METALLIC MATERIALS - GENERAL RULES
    EN ISO 9606-3 : 1999 Approval testing of welders - Fusion welding - Part 3: Copper and copper alloys (ISO 9606-3:1999)
    EN 50159 : 2010 RAILWAY APPLICATIONS - COMMUNICATION, SIGNALLING AND PROCESSING SYSTEMS - SAFETY-RELATED COMMUNICATION IN TRANSMISSION SYSTEMS
    EN 10255:2004+A1:2007 NON-ALLOY STEEL TUBES SUITABLE FOR WELDING AND THREADING - TECHNICAL DELIVERY CONDITIONS
    EN 13555 : 2014 FLANGES AND THEIR JOINTS - GASKET PARAMETERS AND TEST PROCEDURES RELEVANT TO THE DESIGN RULES FOR GASKETED CIRCULAR FLANGE CONNECTIONS
    ISO 898-1:2013 Mechanical properties of fasteners made of carbon steel and alloy steel Part 1: Bolts, screws and studs with specified property classes Coarse thread and fine pitch thread
    EN 10222-1 : 2017 STEEL FORGINGS FOR PRESSURE PURPOSES - PART 1: GENERAL REQUIREMENTS FOR OPEN DIE FORGINGS
    ISO 1817:2015 Rubber, vulcanized or thermoplastic Determination of the effect of liquids
    EN 10088-1 : 2014 STAINLESS STEELS - PART 1: LIST OF STAINLESS STEELS
    EN 61508-4 : 2010 FUNCTIONAL SAFETY OF ELECTRICAL/ELECTRONIC/PROGRAMMABLE ELECTRONIC SAFETY-RELATED SYSTEMS - PART 4: DEFINITIONS AND ABBREVIATIONS
    ISO 9606-3:1999 Approval testing of welders Fusion welding Part 3: Copper and copper alloys
    EN 60384-16 : 2005 FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT - PART 16: SECTIONAL SPECIFICATION: FIXED METALLIZED POLYPROPYLENE FILM DIELECTRIC D.C. CAPACITORS
    SAE J 995 : 2012 MECHANICAL AND MATERIAL REQUIREMENTS FOR STEEL NUTS
    IEC 60730-1:2013+AMD1:2015 CSV Automatic electrical controls - Part 1: General requirements
    EN ISO 3506-2 : 2009 MECHANICAL PROPERTIES OF CORROSION-RESISTANT STAINLESS STEEL FASTENERS - PART 2: NUTS (ISO 3506-2:2009)
    EN 12186 : 2014 GAS INFRASTRUCTURE - GAS PRESSURE REGULATING STATIONS FOR TRANSMISSION AND DISTRIBUTION - FUNCTIONAL REQUIREMENTS
    EN 257 : 2010 MECHANICAL THERMOSTATS FOR GAS-BURNING APPLIANCES
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective