Skip to content
Please enter a keyword to search

  • IEC 60034-1:2017

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    Rotating electrical machines - Part 1: Rating and performance

    Available format(s):  Hardcopy, PDF, PDF 3 Users, PDF 5 Users, PDF 9 Users

    Superseded date:  14-02-2022

    Language(s):  English - French

    Published date:  09-05-2017

    Publisher:  International Electrotechnical Committee

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Duty
    5 Rating
    6 Site conditions
    7 Electrical operating conditions
    8 Thermal performance and tests
    9 Other performance and tests
    10 Rating plates
    11 Miscellaneous requirements
    12 Tolerances
    13 Electromagnetic compatibility (EMC)
    14 Safety
    Annex A (informative) - Guidance for the application
            of duty type S10 and for establishing the value of
            relative thermal life expectancy TL
    Annex B (informative) - Electromagnetic compatibility
            (EMC) limits
    Bibliography

    Abstract - (Show below) - (Hide below)

    IEC 60034-1:2017 is now available as IEC 60034-1:2017 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.

    IEC 60034-1:2017 is applicable to all rotating electrical machines except those covered by other IEC standards, for example, IEC 60349. Machines within the scope of this document may also be subject to superseding, modifying or additional requirements in other standards, for example, IEC 60079 and IEC 60092. This new edition contains a number of clarifications, corrections and enhancements with regard to the previous edition.

    General Product Information - (Show below) - (Hide below)

    Committee TC 2
    Development Note Stability Date: 2020. (05/2017)
    Document Type Standard
    Publisher International Electrotechnical Committee
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    DIN EN 14161:2015-07 ABSCHLUESSE AUSSEN UND AUSSENJALOUSIEN - LEISTUNGS- UND SICHERHEITSANFORDERUNGEN
    CEI EN 60349-4 : 2014 ELECTRIC TRACTION - ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 4: PERMANENT MAGNET SYNCHRONOUS ELECTRICAL MACHINES CONNECTED TO AN ELECTRONIC CONVERTER
    PD ISO/TS 19466:2017 Electrically propelled mopeds and motorcycles. Test method for evaluating performance of regenerative braking systems
    BS EN 60349-1:2010 Electric traction. Rotating electrical machines for rail and road vehicles Machines other than electronic converter-fed alternating current motors
    DIN EN ISO 13350:2016-02 FANS - PERFORMANCE TESTING OF JET FANS (ISO 13350:2015)
    DIN ISO 8528-5:1997-11 RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 5: GENERATING SETS
    I.S. EN 60079-0:2012 EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS (IEC 60079-0:2011 (MOD))
    DIN EN ISO 5802:2016-02 INDUSTRIAL FANS - PERFORMANCE TESTING IN SITU (ISO 5802:2001 + AMD 1:2015)
    BS EN 61800-9-2:2017 Adjustable speed electrical power drive systems Ecodesign for power drive systems, motor starters, power electronics and their driven applications. Energy efficiency indicators for power drive systems and motor starters
    04/30115708 DC : DRAFT JUL 2004 IEC TS 60034-17 - ROTATING ELECTRICAL MACHINES - PART 17: CAGE INDUCTION MOTORS WHEN FED FROM CONVERTERS - APPLICATION GUIDE
    BS IEC 60079-19:1993 Electrical apparatus for explosive gas atmospheres Repair and overhaul for apparatus used in explosive atmospheres (other than mines or explosives)
    BS ISO 8528-4:2005 Reciprocating internal combustion engine driven alternating current generating sets Controlgear and switchgear
    02/206929 DC : DRAFT JUN 2002 IEC 60034-25. ED.1 - ROTATING ELECTRICAL MACHINES - PART 25: GUIDE FOR THE DESIGN AND PERFORMANCE OF CAGE INDUCTION MOTORS FOR CONVERTER SUPPLY
    I.S. EN 60034-30-1:2014 ROTATING ELECTRICAL MACHINES - PART 30-1: EFFICIENCY CLASSES OF LINE OPERATED AC MOTORS (IE CODE)
    BS EN 61800-9-1:2017 Adjustable speed electrical power drive systems Ecodesign for power drive systems, motor starters, power electronics and their driven applications. General requirements for setting energy efficiency standards for power driven equipment using the extended product approach (EPA) and semi analytic model (SAM)
    BS EN ISO 13350:2015 Fans. Performance testing of jet fans
    01/202453 DC : DRAFT APRIL 2001 IEC 60034-9 ED.4 - ROTATING ELECTRICAL MACHINERY - PART 9: NOISE LIMITS
    BS EN 60034-3:2008 Rotating electrical machines Specific requirements for synchronous generators driven by steam turbines or combustion gas turbines
    12/30261858 DC : 0 BS EN 60079-31/ED 2 - EXPLOSIVE ATMOSPHERES - PART 31: EQUIPMENT DUST IGNITION PROTECTION BY ENCLOSURE 'T'
    BS EN 50019:2000 Electrical apparatus for potentially explosive atmospheres. Increased safety \'e\'
    BIS IS/ISO 8528-4 : 2005(R2014) RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 4: CONTROLGEAR AND SWITCHGEAR
    17/30347395 DC : 0 BS EN 60034-2-3 - ROTATING ELECTRICAL MACHINES - PART 2-3: SPECIFIC TEST METHODS FOR DETERMINING LOSSES AND EFFICIENCY OF CONVERTER-FED AC MOTOR
    06/30153363 DC : DRAFT JULY 2006 BS IEC 60079-31 - EXPLOSIVE ATMOSPHERES - PART 31 - EQUIPMENT - PROTECTION BY ENCLOSURE "TD"
    BS EN 60034-22:2009 Rotating electrical machines AC generators for reciprocating internal combustion (RIC) engine driven generating sets
    IEC 60204-1:2016 Safety of machinery - Electrical equipment of machines - Part 1: General requirements
    03/316174 DC : DRAFT SEP 2003 ISO 8528-5 - RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 5: GENERATING SETS
    PD IEC/TS 60034-2-3:2013 Rotating electrical machines Specific test methods for determining losses and efficiency of converter-fed AC induction motors
    17/30363845 DC : 0 BS ISO 21927-3 - SMOKE AND HEAT CONTROL SYSTEMS - PART 3: SPECIFICATION FOR POWERED SMOKE AND HEAT EXHAUST VENTILATORS
    PREN 328 : DRAFT 2012 HEAT EXCHANGERS - FORCED CONVECTION UNIT AIR COOLERS FOR REFRIGERATION - TEST PROCEDURES FOR ESTABLISHING THE PERFORMANCE
    IEEE 1095-2012 REDLINE IEEE Guide for the Installation of Vertical Generators and Generator/Motors for Hydroelectric Applications
    CEI EN 61400-22 : 2011 WIND TURBINES - PART 22: CONFORMITY TESTING AND CERTIFICATION
    13/30294866 DC : 0 BS EN 61058-1 - SWITCHES FOR APPLIANCES - PART 1: GENERAL REQUIREMENTS
    BS EN 60034-15:2009 Rotating electrical machines Impulse voltage withstand levels of form-wound stator coils for rotating a.c. machines
    GOST R 52350.1 : 2005 ELECTRICAL APPARATUS FOR EXPLOSIVE GAS ATMOSPHERES - PART 1: FLAMEPROOF ENCLOSURES "D"
    ISO 19372:2015 Microturbines applications — Safety
    14/30297346 DC : 0 BS ISO 8528-8 - RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 8: GENERATING SETS
    CEI EN 60034-3 : 2011 ROTATING ELECTRICAL MACHINES - PART 3: SPECIFIC REQUIREMENTS FOR SYNCHRONOUS GENERATORS DRIVEN BY STEAM TURBINES OR COMBUSTION GAS TURBINES
    08/30186575 DC : DRAFT JULY 2008 BS EN 60079-15 ED. 4 - EXPLOSIVE ATMOSPHERES - PART 15: EQUIPMENT PROTECTION BY TYPE OF PROTECTION "N"
    API 689 : 2007 COLLECTION AND EXCHANGE OF RELIABILITY AND MAINTENANCE DATA FOR EQUIPMENT
    05/30138181 DC : DRAFT AUG 2005 IEC 60034-8 ED 3 - ROTATING ELECTRICAL MACHINES - PART 8: TERMINAL MARKINGS AND DIRECTION OF ROTATION
    14/30271543 DC : 0 BS EN ISO 13350 - INDUSTRIAL FANS - PERFORMANCE TESTING OF JET FANS
    15/30330275 DC : 0 BS EN 60034-4 ED 4.0 - ROTATING ELECTRICAL MACHINES - PART 4: METHODS FOR DETERMINING SYNCHRONOUS MACHINE QUANTITIES FROM TESTS
    BS ISO 3977-3:2004 Gas turbines. Procurement Design requirements
    BS EN 60034-18-1:2010 Rotating electrical machines Functional evaluation of insulation systems. General guidelines
    I.S. EN 60034-18-34:2012 ROTATING ELECTRICAL MACHINES - PART 18-34: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR FORM-WOUND WINDINGS - EVALUATION OF THERMOMECHANICAL ENDURANCE OF INSULATION SYSTEMS (IEC 60034-18-34:2012 (EQV))
    BS ISO 3977-8:2002 Gas turbines. Procurement Inspection, testing, installation and commissioning
    UNE-EN ISO 13350:2016 Fans - Performance testing of jet fans (ISO 13350:2015)
    BS 4999-115:1992 General requirements for rotating electrical machines Impulse voltage withstand levels of rotating a.c. machines with form-wound stator coils
    03/113813 DC : 0 IEC 60034-2. ED.4 - ROTATING ELECTRICAL MACHINES - PART 2: METHODS FOR DETERMINING LOSSES AND EFFICIENCY FROM TESTS (EXCLUDING MACHINES FOR TRACTION VEHICLES)
    08/30184583 DC : DRAFT JUNE 2008 BS IEC/TS 60034-18-32 - ROTATING ELECTRICAL MACHINES - PART 18-32: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR FORM-WOUND WINDINGS - ELECTRICAL EVALUATION OF INSULATION SYSTEMS USED IN ROTATING ELECTRICAL MACHINES
    BS EN 60027-4:2007 Letter symbols to be used in electric technology Rotating electric machines
    BS ISO 13380:2002 Condition monitoring and diagnostics of machines. General guidelines on using performance parameters
    NF EN 60079-15 : 2010 EXPLOSIVE ATMOSPHERES - PART 15: EQUIPMENT PROTECTION BY TYPE OF PROTECTION 'N'
    NF ISO 3977-8 : 2002 GAS TURBINES - PROCUREMENT - PART 8: INSPECTION, TESTING, INSTALLATION AND COMMISSIONING
    CSA C22.2 No. 60079.0 : 2015 EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS
    98/201424 DC : DRAFT MARCH 1998 IEC 61972 - METHOD FOR DETERMINING LOSSES AND EFFICIENCY OF THREE-PHASE, CAGE INDUCTION MOTORS
    BS 848-10(1999) : 1999 FANS FOR GENERAL PURPOSES - PART 10: PERFORMANCE TESTING OF JET FANS
    CSA E60079.15 : 2002 : R2011 ELECTRICAL APPARATUS FOR EXPLOSIVE GAS ATMOSPHERES - ELECTRICAL APPARATUS WITH TYPE OF PROTECTION "n"
    I.S. EN 60034-30:2009 ROTATING ELECTRICAL MACHINES - PART 30: EFFICIENCY CLASSES OF SINGLE-SPEED, THREE-PHASE, CAGE-INDUCTION MOTORS
    CEI EN 50216-7 : 2002 POWER TRANSFORMER AND REACTOR FITTINGS - PART 7: ELECTRIC PUMPS FOR TRANSFORMER OIL
    CEI EN 61116 : 1996 ELECTROMECHANICAL EQUIPMENT GUIDE FOR SMALL HYDROELECTRIC INSTALLATIONS
    CEI EN 60034-18-34 : 2013 ROTATING ELECTRICAL MACHINES - PART 18-34: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR FORM-WOUND WINDINGS - EVALUATION OF THERMOMECHANICAL ENDURANCE OF INSULATION SYSTEMS
    CEI EN 60034-18-21 : 2014 ROTATING ELECTRICAL MACHINES - PART 18-21: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR WIRE-WOUND WINDINGS - THERMAL EVALUATION AND CLASSIFICATION
    S.R. CLC/TS 50537-3:2010 RAILWAY APPLICATIONS - MOUNTED PARTS OF THE TRACTION TRANSFORMER AND COOLING SYSTEM - PART 3: WATER PUMP FOR TRACTION CONVERTERS
    EN 61800-9-2:2017 Adjustable speed electrical power drive systems - Part 9-2: Ecodesign for power drive systems, motor starters, power electronics and their driven applications - Energy efficiency indicators for power drive systems and motor starters
    I.S. EN 60694:1999 COMMON SPECIFICATIONS FOR HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR STANDARDS
    I.S. EN 50019:2001 ELECTRICAL APPARATUS FOR POTENTIALLY EXPLOSIVE ATMOSPHERES - INCREASED SAFETY "E"
    CEI EN 60034-29 : 2009 ROTATING ELECTRICAL MACHINES - PART 29: EQUIVALENT LOADING AND SUPERPOSITION TECHNIQUES - INDIRECT TESTING TO DETERMINE TEMPERATURE RISE
    CEI CLC/TS 50537-2 : 2011 RAILWAY APPLICATIONS - MOUNTED PARTS OF THE TRACTION TRANSFORMER AND COOLING SYSTEM - PART 2: PUMP FOR INSULATING LIQUID FOR TRACTION TRANSFORMERS AND REACTORS
    IEC 60079-0 REDLINE : 7.0 EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS
    EN 62271-1:2017 High-voltage switchgear and controlgear - Part 1: Common specifications for alternating current switchgear and controlgear
    CSA C61400-2:2008 WIND TURBINES - PART 2: DESIGN REQUIREMENTS FOR SMALL WIND TURBINES
    S.R. CLC/TS 50537-2:2010 RAILWAY APPLICATIONS - MOUNTED PARTS OF THE TRACTION TRANSFORMER AND COOLING SYSTEM - PART 2: PUMP FOR INSULATING LIQUID FOR TRACTION TRANSFORMERS AND REACTORS
    IEC TS 60034-32:2016 Rotating electrical machines - Part 32: Measurement of stator end-winding vibration at form-wound windings
    I.S. EN 60034-18-21:2013 ROTATING ELECTRICAL MACHINES - - PART 18-21: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR WIREWOUND WINDINGS - THERMAL EVALUATION AND CLASSIFICATION (IEC 60034-18-21:2012 (EQV))
    I.S. EN 60034-9:2005 ROTATING ELECTRICAL MACHINES - PART 9: NOISE LIMITS
    I.S. EN 15714-2:2009 INDUSTRIAL VALVES - ACTUATORS - PART 2: ELECTRIC ACTUATORS FOR INDUSTRIAL VALVES - BASIC REQUIREMENTS
    I.S. EN 60947-4-2:2012 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 4-2: CONTACTORS AND MOTOR-STARTERS - AC SEMICONDUCTOR MOTOR CONTROLLERS AND STARTERS
    ISO 3977-3:2004 Gas turbines — Procurement — Part 3: Design requirements
    ISO 8528-4:2005 Reciprocating internal combustion engine driven alternating current generating sets — Part 4: Controlgear and switchgear
    BS ISO 8528-5:2013 Reciprocating internal combustion engine driven alternating current generating sets Generating sets
    ISO 13380:2002 Condition monitoring and diagnostics of machines General guidelines on using performance parameters
    16/30341165 DC : 0 BS EN 14492-2 - CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 2: POWER DRIVEN HOISTS
    CEI EN 60034-11 : 2005 ROTATING ELECTRICAL MACHINES - PART 11: THERMAL PROTECTION
    BIS IS/ISO 8528-5 : 2005(R2014) RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 5: GENERATING SETS
    S.R. CLC/TS 60034-31:2011 ROTATING ELECTRICAL MACHINES - PART 31: SELECTION OF ENERGY-EFFICIENT MOTORS INCLUDING VARIABLE SPEED APPLICATIONS - APPLICATION GUIDE
    I.S. EN 60034-11:2004 ROTATING ELECTRICAL MACHINES - PART 11: THERMAL PROTECTION
    I.S. EN 61241-4:2007 ELECTRICAL APPARATUS FOR USE IN THE PRESENCE OF COMBUSTIBLE DUST - PART 4: TYPE OF PROTECTION 'PD'
    I.S. EN 60034-2-2:2010 ROTATING ELECTRICAL MACHINES - PART 2-2: SPECIFIC METHODS FOR DETERMINING SEPARATE LOSSES OF LARGE MACHINES FROM TESTS - SUPPLEMENT TO IEC 60034-2-1
    CSA C22.2 No. 61058.1 : 2009 : R2014 SWITCHES FOR APPLIANCES - PART 1: GENERAL REQUIREMENTS
    NF EN 60034-28 : 2013 ROTATING ELECTRICAL MACHINES - PART 28: TEST METHODS FOR DETERMINING QUANTITIES OF EQUIVALENT CIRCUIT DIAGRAMS FOR THREE-PHASE LOW-VOLTAGE CAGE INDUCTION MOTORS
    VDE 0160-109-2 : 2018-01 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 9-2: ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS AND THEIR DRIVEN APPLICATIONS - ENERGY EFFICIENCY INDICATORS FOR POWER DRIVE SYSTEMS AND MOTOR STARTERS (IEC 61800-9-2:2017)
    ISO 8528-5:2013 Reciprocating internal combustion engine driven alternating current generating sets Part 5: Generating sets
    NFPA 79 : 2018 ELECTRICAL STANDARD FOR INDUSTRIAL MACHINERY
    EN 60335-1:2012/A13:2017 HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60335-1:2010, MODIFIED)
    EN IEC 60079-7:2015/A1:2018 EXPLOSIVE ATMOSPHERES - PART 7: EQUIPMENT PROTECTION BY INCREASED SAFETY 'E' (IEC 60079-7:2015/A1:2017)
    DIN EN 13135-1:2011-04 CRANES - EQUIPMENT - PART 1: ELECTROTECHNICAL EQUIPMENT
    IEC 60034-4:2008 Rotating electrical machines - Part 4: Methods for determining synchronous machine quantities from tests
    BS EN 12101-3:2015 Smoke and heat control systems Specification for powered smoke and heat control ventilators (Fans)
    17/30338554 DC : 0 BS EN 1175 - SAFETY OF INDUSTRIAL TRUCKS - ELECTRICAL/ELECTRONIC REQUIREMENTS
    IEC 61400-2:2013 Wind turbines - Part 2: Small wind turbines
    06/30154990 DC : 0 BS EN 60204-32 - SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 32: REQUIREMENTS FOR HOISTING MACHINES
    05/30060689 DC : DRAFT JUN 2005 IEC 62282-3-1 - FUEL CELL TECHNOLOGIES - PART 3-1: STATIONARY FUEL CELL POWER PLANTS - SAFETY
    15/30286010 DC : 0 BS ISO 14990-1 - EARTH-MOVING MACHINERY - ELECTRICAL SAFETY OF MACHINES UTILISING ELECTRIC DRIVES AND RELATED COMPONENTS AND SYSTEMS - PART 1: GENERAL REQUIREMENTS
    IEC 60694:1996+AMD1:2000+AMD2:2001 CSV Common specifications for high-voltage switchgear and controlgear standards
    15/30286835 DC : 0 BS ISO 14990-2 - EARTH-MOVING MACHINERY - ELECTRICAL SAFETY OF MACHINES UTILISING ELECTRIC DRIVES AND RELATED COMPONENTS AND SYSTEMS - PART 2: PARTICULAR REQUIREMENTS FOR EXTERNALLY-POWERED MACHINES
    14/30244780 DC : 0 BS ISO 19859 - GAS TURBINE APPLICATIONS - REQUIREMENTS FOR POWER GENERATION
    EN 61800-5-1:2007/A1:2017 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 5-1: SAFETY REQUIREMENTS - ELECTRICAL, THERMAL AND ENERGY (IEC 61800-5-1:2007/A1:2016)
    CEI EN 61800-1 : 2000 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 1: GENERAL REQUIREMENTS - RATING SPECIFICATIONS FOR LOW VOLTAGE ADJUSTABLE SPEED D.C. POWER DRIVE SYSTEMS
    EN 12101-3:2015 Smoke and heat control systems - Part 3: Specification for powered smoke and heat control ventilators (Fans)
    EN 60034-15:2009 Rotating electrical machines - Part 15: Impulse voltage withstand levels of form-wound stator coils for rotating a.c. machines
    EN 61058-1:2002/A2:2008 SWITCHES FOR APPLIANCES - PART 1: GENERAL REQUIREMENTS
    EN 60034-22:2009 Rotating electrical machines - Part 22: AC generators for reciprocating internal combustion (RIC) engine driven generating sets
    EN 61400-2:2014 Wind turbines - Part 2: Small wind turbines
    EN 60694:1996/A2:2001 COMMON SPECIFICATIONS FOR HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR STANDARDS
    EN 60034-11:2004 Rotating electrical machines - Part 11: Thermal protection
    EN 60034-18-32:2010 Rotating electrical machines - Part 18-32: Functional evaluation of insulation systems - Test procedures for form-wound windings - Evaluation by electrical endurance
    EN 60204-11:2000/corrigendum:2010 SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 11: REQUIREMENTS FOR HV EQUIPMENT FOR VOLTAGES ABOVE 1000 V A.C. OR 1500 V D.C. AND NOT EXCEEDING 36 KV
    EN 60947-4-2:2012 Low-voltage switchgear and controlgear - Part 4-2: Contactors and motor-starters - AC semiconductor motor controllers and starters
    EN 60034-2-1:2014 Rotating electrical machines - Part 2-1: Standard methods for determining losses and efficiency from tests (excluding machines for traction vehicles)
    EN 60034-9:2005/A1:2007 ROTATING ELECTRICAL MACHINES - PART 9: NOISE LIMITS
    EN 60034-2-2:2010 Rotating electrical machines - Part 2-2: Specific methods for determining separate losses of large machines from tests - Supplement to IEC 60034-2-1
    EN 60034-14:2004/A1:2007 ROTATING ELECTRICAL MACHINES - PART 14: MECHANICAL VIBRATION OF CERTAIN MACHINES WITH SHAFT HEIGHTS 56 MM AND HIGHER - MEASUREMENT, EVALUATION AND LIMITS OF VIBRATION SEVERITY
    EN 60034-30-1:2014 Rotating electrical machines - Part 30-1: Efficiency classes of line operated AC motors (IE code)
    EN 1175-1:1998+A1:2010 Safety of industrial trucks - Electrical requirements - Part 1: General requirements for battery powered trucks
    EN 60947-4-1 : 2010 AMD 1 2012 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 4-1: CONTACTORS AND MOTOR-STARTERS - ELECTROMECHANICAL CONTACTORS AND MOTOR-STARTERS (IEC 60947-4-1:2009/A1:2012)
    EN 60034-18-34:2012 Rotating electrical machines - Part 18-34: Functional evaluation of insulation systems - Test procedures for form-wound windings - Evaluation of thermomechanical endurance of insulation systems
    EN 60034-8:2007/A1:2014 ROTATING ELECTRICAL MACHINES - PART 8: TERMINAL MARKINGS AND DIRECTION OF ROTATION (IEC 60034-8:2007/A1:2014)
    EN 60034-18-31 : 2012 ROTATING ELECTRICAL MACHINES - PART 18-31: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR FORM-WOUND WINDINGS - THERMAL EVALUATION AND CLASSIFICATION OF INSULATION SYSTEMS USED IN ROTATING MACHINES (IEC 60034-18-31:2012)
    EN 60034-18-1:2010 Rotating electrical machines - Part 18-1: Functional evaluation of insulation systems - General guidelines
    EN 12693:2008 Refrigerating systems and heat pumps - Safety and environmental requirements - Positive displacement refrigerant compressors
    EN 60947-6-2:2003/A1:2007 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 6-2: MULTIPLE FUNCTION EQUIPMENT - CONTROL AND PROTECTIVE SWITCHING DEVICES (OR EQUIPMENT) (CPS)
    EN 328:2014 Heat exchangers - Forced convection unit air coolers for refrigeration - Test procedures for establishing the performance
    EN 12255-1:2002 Wastewater treatment plants - Part 1: General construction principles
    NBR IEC 60034-9 : 2011 ROTATING ELECTRICAL MACHINES - PART 9: NOISE LIMITS
    EN 88528-11:2004 Reciprocating internal combustion engine driven alternating current generating sets - Part 11: Rotary uninterruptible power systems - Performance requirements and test methods
    NBR IEC 60079-0 : 2013 ERRATA 2 2016 EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS
    EN 50598-1:2014 Ecodesign for power drive systems, motor starters, power electronics & their driven applications - Part 1: General requirements for setting energy efficiency standards for power driven equipment using the extended product approach (EPA), and semi analytic model (SAM)
    15/30265353 DC : 0 BS EN 62271-1 ED 2 - HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 1: COMMON SPECIFICATIONS FOR ALTERNATING CURRENT SWITCHGEAR AND CONTROLGEAR
    BS IEC TS 60034-18.34 : 2000 AMD 16621 ROTATING ELECTRICAL MACHINES - PART 18-34: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR FORM-WOUND WINDINGS - EVALUATION OF THERMOMECHANICAL ENDURANCE OF INSULATION SYSTEMS
    ISO 21873-1:2015 Building construction machinery and equipment Mobile crushers Part 1: Terminology and commercial specifications
    DIN EN 61800-9-2 : 2018-01 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 9-2: ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS AND THEIR DRIVEN APPLICATIONS - ENERGY EFFICIENCY INDICATORS FOR POWER DRIVE SYSTEMS AND MOTOR STARTERS (IEC 61800-9-2:2017)
    CEI EN 60034-28 : 2014 ROTATING ELECTRICAL MACHINES - PART 28: TEST METHODS FOR DETERMINING QUANTITIES OF EQUIVALENT CIRCUIT DIAGRAMS FOR THREE-PHASE LOW-VOLTAGE CAGE INDUCTION MOTORS
    GOST R ISO 8528-3 : 2005 RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 3: ALTERNATING CURRENT GENERATORS FOR GENERATING SETS
    BS IEC 60034-17:1998 Rotating electrical machines Cage induction motors when fed from converters. Application guide
    DD CLC/TS 60034-18-34:2004 Rotating electrical machines. Functional evaluation of insulation systems Test procedures for form-wound windings. Evaluation of thermomechanical endurance of insulation systems
    BS IEC 60092-301:1980 Electrical installation in ships Equipment. Generators and motors
    17/30358367 DC : 0 BS EN 17128 - NON-APPROVED LIGHT MOTORIZED VEHICLES FOR THE TRANSPORTATION OF PERSONS AND GOODS AND RELATED FACILITIES - PERSONAL LIGHT ELECTRIC VEHICLES (PLEV) - SAFETY REQUIREMENTS AND TEST METHODS
    ISO 5801:2017 Fans — Performance testing using standardized airways
    04/19993045 DC : 0 EN 14492-1 - CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 1: POWER DRIVEN WINCHES
    DEFSTAN 02-607/2(2008) : 2008 DESIGN OF HIGH VOLTAGE ELECTRICAL POWER SYSTEMS FOR HM SHIPS, SUBMARINES AND THE ROYAL FLEET AUXILIARY
    PD IEC/TR 62001:2009 High-voltage direct current (HVDC) systems. Guidebook to the specification and design evaluation of A.C. filters
    12/30248232 DC : DRAFT AUG 2012 BS EN 61400-2 - WIND TURBINES - PART 2: SMALL WIND TURBINES
    BS EN 60034-18-21:2013 Rotating electrical machines Functional evaluation of insulation systems. Test procedures for wire-wound windings. Thermal evaluation and classification
    BS EN 60349-4:2013 Electric traction. Rotating electrical machines for rail and road vehicles Permanent magnet synchronous electrical machines connected to an electronic converter
    BS EN 61986:2002 Rotating electrical machines. Equivalent loading and super-position techniques. Indirect testing to determine temperature rise
    09/30209334 DC : 0 BS EN 60034-2-3 - ROTATING ELECTRICAL MACHINES - PART 2-3: SPECIFIC TEST METHODS FOR DETERMINING LOSSES AND EFFICIENCY OF CONVERTER-FED AC MOTORS
    I.S. EN 61800-9-2:2017 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 9-2: ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS AND THEIR DRIVEN APPLICATIONS - ENERGY EFFICIENCY INDICATORS FOR POWER DRIVE SYSTEMS AND MOTOR STARTERS
    CEI EN 60034-18-32 : 2011 ROTATING ELECTRICAL MACHINES - PART 18-32: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR FORM-WOUND WINDINGS - EVALUATION OF ELECTRICAL ENDURANCE
    11/30229676 DC : 0 BS ISO 8528-5 - RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 5: GENERATING SETS
    06/30159940 DC : 0 BS EN 60034-15 - ROTATING ELECTRICAL MACHINES - PART 15: IMPULSE VOLTAGE WITHSTAND LEVELS OF ROTATING A.C. - MACHINES WITH FORM-WOUND STATOR COILS
    DIN EN 12693:2016-10 (Draft) REFRIGERATING SYSTEMS AND HEAT PUMPS - SAFETY AND ENVIRONMENTAL REQUIREMENTS - POSITIVE DISPLACEMENT REFRIGERANT COMPRESSORS
    BS EN 50281-1-1:1999 Electrical apparatus for use in the presence of combustible dust. Electrical apparatus protected by enclosures Construction and testing
    EN 61800-2:2015 Adjustable speed electrical power drive systems - Part 2: General requirements - Rating specifications for low voltage adjustable speed a.c. power drive systems
    13/30278886 DC : 0 BS EN 60092-501 - ELECTRICAL INSTALLATIONS IN SHIPS - PART 501: SPECIAL FEATURES - ELECTRIC PROPULSION PLANT
    API 616 : 2011 GAS TURBINES FOR THE PETROLEUM, CHEMICAL, AND GAS INDUSTRY SERVICES
    NF EN ISO 5801 : 2017 FANS - PERFORMANCE TESTING USING STANDARDIZED AIRWAYS
    15/30256504 DC : 0 BS EN 60034-23 ED 1.0 - ROTATING ELECTRICAL MACHINES - PART 23: REPAIR, OVERHAUL AND RECLAMATION
    DD CLC/TS 50537-3:2010 Railway applications. Mounted parts of the traction transformer and cooling system Water pump for traction converters
    I.S. EN 88528-11:2004 RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - ROTARY UNINTERRUPTIBLE POWER SYSTEMS - PERFORMANCE REQUIREMENTS AND TEST METHODS
    IEC TR 62001-1:2016 High-voltage direct current (HVDC) systems - Guidance to the specification and design evaluation of AC filters - Part 1: Overview
    BS EN 50216-7:2002 Power transformers and reactor fittings Electric pumps for transformer oil
    01/202984 DC : DRAFT APR 2001 IEC 60034-11 ED.2 - THERMAL PROTECTION
    DIN ISO 8528-1:1997-11 RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 1: APPLICATION, RATINGS AND PERFORMANCE
    CLC/TS 50537-2:2010 Railway applications - Mounted parts of the traction transformer and cooling system - Part 2: Pump for insulating liquid for traction transformers and reactors
    ISO 21927-3:2006 Smoke and heat control systems Part 3: Specification for powered smoke and heat exhaust ventilators
    UNI CEI EN 45510-2-5 : 2011 GUIDE FOR PROCUREMENT OF POWER STATION EQUIPMENT - PART 2-5: ELECTRICAL EQUIPMENT - MOTORS
    NF EN 60034-5 : 2001 AMD 1 2007 ROTATING ELECTRICAL MACHINES - PART 5: DEGREES OF PROTECTION PROVIDED BY THE INTEGRAL DESIGN OF ROTATING ELECTRICAL MACHINES (IP CODE) - CLASSIFICATION
    DD IEC TS 60034-31 : DRAFT JULY 2010 ROTATING ELECTRICAL MACHINES - PART 31: SELECTION OF ENERGY-EFFICIENT MOTORS INCLUDING VARIABLE SPEED APPLICATIONS - APPLICATION GUIDE
    11/30247355 DC : 0 BS EN 60034-30 ED 2 - ROTATING ELECTRICAL MACHINES - PART 30: EFFICIENCY CLASSES OF SINGLE-SPEED, THREE-PHASE, CAGE-INDUCTION MOTORS (IE-CODE)
    BS EN 60034-18-34:2012 Rotating electrical machines Functional evaluation of insulation systems. Test procedures for form-wound windings. Evaluation of thermomechanical endurance of insulation systems
    BS EN 15268:2008 Petrol filling stations. Safety requirements for the construction of submersible pump assemblies
    18/30368743 DC (published 2018-04) BS EN 60947-6-2. Low-voltage switchgear and controlgear Part 6-2. Multiple function equipment. Control and protective switching devices (or equipment) (CPS)
    02/203983 DC : DRAFT MAR 2002 IEC 60034-3. ED.5 - ROTATING ELECTRICAL MACHINES - PART 3: SPECIFIC REQUIREMENTS FOR CYLINDRICAL ROTOR SYNCHRONOUS MACHINES
    CLC/TS 50537-3:2010 Railway applications - Mounted parts of the traction transformer and cooling system - Part 3: Water pump for traction converters
    BS EN 12693:2008 Refrigerating systems and heat pumps. Safety and environmental requirements. Positive displacement refrigerant compressors
    04/30111859 DC : 0 IEC 62271-1 - HIGH-VOLTAGE SWITCHGEAR AND CONTROL GEAR - PART 1: COMMON SPECIFICATIONS
    BS EN 45510-2-5:2002 Guide for the procurement of power station equipment. Electrical equipment Motors
    BS EN 50016:2002 Electrical apparatus for potentially explosive atmospheres. Pressurized apparatus \'p\'
    07/30065083 DC : DRAFT JUNE 2007 BS EN 60027-4 - LETTER SYMBOLS TO BE USED IN ELECTRICAL TECHNOLOGY - PART 4: ROTATING ELECTRIC MACHINES
    I.S. EN 60335-1:2012 HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 1: GENERAL REQUIREMENTS
    I.S. EN 61800-9-1:2017 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 9-1: ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS AND THEIR DRIVEN APPLICATIONS - GENERAL REQUIREMENTS FOR SETTING ENERGY EFFICIENCY STANDARDS FOR POWER DRIVEN EQUIPMENT USING THE EXTENDED PRODUCT APPROACH (EPA) AND SEMI ANALYTIC MODEL (SAM)
    03/316172 DC : DRAFT SEP 2003 ISO 8528-3 - RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 3: ALTERNATING CURRENT GENERATORS FOR GENERATING SETS
    (INACTIVE RECORD)IEEE C50.12 : 2005 SALIENT-POLE 50 HZ AND 60 HZ SYNCHRONOUS GENERATORS AND GENERATOR/MOTORS FOR HYDRAULIC TURBINE APPLICATIONS RATED 5 MVA AND ABOVE
    CSA ISO 50004 : 2015 ENERGY MANAGEMENT SYSTEMS - GUIDANCE FOR THE IMPLEMENTATION, MAINTENANCE AND IMPROVEMENT OF AN ENERGY MANAGEMENT SYSTEM
    GOST R ISO 8528-5 : 2005 RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 5: GENERATING SETS
    PREN 50598-1 : DRAFT 2013 ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS & THEIR DRIVEN APPLICATIONS - PART 1: GENERAL REQUIREMENTS FOR SETTING ENERGY EFFICIENCY STANDARDS FOR POWER DRIVEN EQUIPMENT USING THE EXTENDED PRODUCT APPROACH (EPA), AND SEMI ANALYTIC MODEL (SAM)
    NF EN 60034-9 : 2005 AMD 1 2007 ROTATING ELECTRICAL MACHINES - PART 9: NOISE LIMITS
    BS EN 60079-7 : 2015 EXPLOSIVE ATMOSPHERES - PART 7: EQUIPMENT PROTECTION BY INCREASED SAFETY 'E' (IEC 60079-7:2015)
    FM 1312 : 2018 CENTRIFUGAL FIRE PUMPS (VERTICAL-SHAFT, TURBINE TYPE)
    IEEE DRAFT C50.12 : D10 2004 SALIENT-POLE 50 AND 60 HZ SYNCHRONOUS GENERATORS AND GENERATOR/MOTORS FOR HYDRAULIC TURBINE APPLICATIONS RATED 5 MVA AND ABOVE
    CEI EN 60034-18-1 : 2011 ROTATING ELECTRICAL MACHINES - PART 18-1: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - GENERAL GUIDELINES
    NF EN 60034-18-42 : 2017 ROTATING ELECTRICAL MACHINES - PART 18-42: PARTIAL DISCHARGE RESISTANT ELECTRICAL INSULATION SYSTEMS (TYPE 2) USED IN ROTATING ELECTRICAL MACHINES FED FROM VOLTAGE CONVERTERS - QUALIFICATION TESTS
    IEC 61058-1:2016 Switches for appliances - Part 1: General requirements
    EN 60204-1 : 2006 COR 2010 SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS
    CSA C61400-2 : 2008 : R2018 WIND TURBINES - PART 2: DESIGN REQUIREMENTS FOR SMALL WIND TURBINES
    I.S. CLC TS 60034-25:2005 ROTATING ELECTRICAL MACHINES - PART 25: GUIDE FOR THE DESIGN AND PERFORMANCE OF CAGE INDUCTION MOTORS SPECIFICALLY DESIGNED FOR CONVERTER SUPPLY
    BS EN ISO 5802 : 2008 INDUSTRIAL FANS - PERFORMANCE TESTING IN SITU
    UNI EN 15268 : 2009 PETROL FILLING STATIONS - SAFETY REQUIREMENTS FOR THE CONSTRUCTION OF SUBMERSIBLE PUMP ASSEMBLIES
    BS EN 15194:2017 Cycles. Electrically power assisted cycles. EPAC Bicycles
    BS EN 61058-1 : 2002 SWITCHES FOR APPLIANCES - PART 1: GENERAL REQUIREMENTS
    I.S. EN 61058-1:2002 SWITCHES FOR APPLIANCES - PART 1: GENERAL REQUIREMENTS
    BS EN 60079-0 : 2012 EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS
    I.S. EN 60079-15:2010 EXPLOSIVE ATMOSPHERES - PART 15: EQUIPMENT PROTECTION BY TYPE OF PROTECTION 'N'
    I.S. EN 60034-18-42:2017 ROTATING ELECTRICAL MACHINES - PART 18-42: PARTIAL DISCHARGE RESISTANT ELECTRICAL INSULATION SYSTEMS (TYPE 2) USED IN ROTATING ELECTRICAL MACHINES FED FROM VOLTAGE CONVERTERS - QUALIFICATION TESTS
    I.S. EN 60034-15:2009 ROTATING ELECTRICAL MACHINES - PART 15: IMPULSE VOLTAGE WITHSTAND LEVELS OF FORM-WOUND STATOR COILS FOR ROTATING A.C. MACHINES
    CEI EN 60034-4 : 2009 ROTATING ELECTRICAL MACHINES - PART 4: METHODS FOR DETERMINING SYNCHRONOUS MACHINE QUANTITIES FROM TESTS
    CEI EN 60947-4-2 : 2013 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 4-2: CONTACTORS AND MOTOR-STARTERS - AC SEMICONDUCTOR MOTOR CONTROLLERS AND STARTERS
    CEI EN 61800-9-2 : 1ED 2017 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 9-2: ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS AND THEIR DRIVEN APPLICATIONS - ENERGY EFFICIENCY INDICATORS FOR POWER DRIVE SYSTEMS AND MOTOR STARTERS
    CEI EN 60349-1 : 2012 ELECTRIC TRACTION - ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 1: MACHINES OTHER THAN ELECTRONIC CONVERTER-FED ALTERNATING CURRENT MOTORS
    CLC/TS 60034-20-1:2004 Rotating electrical machines - Part 20-1: Control motors - Stepping motors
    I.S. EN 60034-18-32:2010 ROTATING ELECTRICAL MACHINES - PART 18-32: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR FORM-WOUND WINDINGS - EVALUATION BY ELECTRICAL ENDURANCE
    CSA C22.2 No. 61058.1 : 2009 : INC : UPD 1 : 2013 SWITCHES FOR APPLIANCES - PART 1: GENERAL REQUIREMENTS
    CLC/TS 60034-31:2011 Rotating electrical machines - Part 31: Selection of energy-efficient motors including variable speed applications - Application guide
    DIN EN 61800-9-1 : 2018-01 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 9-1: ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS AND THEIR DRIVEN APPLICATIONS - GENERAL REQUIREMENTS FOR SETTING ENERGY EFFICIENCY STANDARDS FOR POWER DRIVEN EQUIPMENT USING THE EXTENDED PRODUCT APPROACH (EPA) AND SEMI ANALYTIC MODEL (SAM) (IEC 61800-9-1:2017)
    IEC 61058-1 REDLINE : 4ED 2016 SWITCHES FOR APPLIANCES - PART 1: GENERAL REQUIREMENTS
    CSA C22.2 No. 60079-15 : 2016 EXPLOSIVE ATMOSPHERES - PART 15: EQUIPMENT PROTECTION BY TYPE OF PROTECTION 'N'
    I.S. EN 60034-8:2007 ROTATING ELECTRICAL MACHINES - PART 8: TERMINAL MARKINGS AND DIRECTION OF ROTATION
    NF EN 60034-29 : 2008 ROTATING ELECTRICAL MACHINES - PART 29: EQUIVALENT LOADING AND SUPERPOSITION TECHNIQUES - INDIRECT TESTING TO DETERMINE TEMPERATURE RISE
    CEI EN 60079-15 : 2012 EXPLOSIVE ATMOSPHERES - PART 15: EQUIPMENT PROTECTION BY TYPE OF PROTECTION 'N'
    BIS IS/IEC 60079-15 : 2005 ELECTRICAL APPARATUS FOR EXPLOSIVE GAS ATMOSPHERES - PART 15: CONSTRUCTION, TEST AND MARKING OF TYPE OF PROTECTION 'N' ELECTRICAL APPARATUS
    EN 61936-1 : 2010 AMD 1 2014 POWER INSTALLATIONS EXCEEDING 1 KV A.C. - PART 1: COMMON RULES (IEC 61936-1:2010/A1:2014)
    NF EN 60034-4 : 2008 ROTATING ELECTRICAL MACHINES - PART 4: METHODS FOR DETERMINING SYNCHRONOUS MACHINE QUANTITIES FROM TESTS
    IEC 61800-2:2015 Adjustable speed electrical power drive systems - Part 2: General requirements - Rating specifications for low voltage adjustable speed a.c. power drive systems
    I.S. EN 60204-32:2008 SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 32: REQUIREMENTS FOR HOISTING MACHINES
    ISO/TR 18569:2004 Safety of machinery Guidelines for the understanding and use of safety of machinery standards
    IEC 62271-1:2017 High-voltage switchgear and controlgear - Part 1: Common specifications for alternating current switchgear and controlgear
    IEC TS 60034-18-34:2000 Rotating electrical machines - Part 18-34: Functional evaluation of insulation systems - Test procedures for form-wound windings - Evaluation of thermomechanical endurance of insulation systems
    I.S. EN 61800-5-1:2007 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 5-1: SAFETY REQUIREMENTS - ELECTRICAL, THERMAL AND ENERGY
    I.S. EN 60034-2-1:2014 ROTATING ELECTRICAL MACHINES - PART 2-1: STANDARD METHODS FOR DETERMINING LOSSES AND EFFICIENCY FROM TESTS (EXCLUDING MACHINES FOR TRACTION VEHICLES)
    IEC 60079-1:2014 RLV Explosive atmospheres - Part 1: Equipment protection by flameproof enclosures "d"
    S.R. CWA 15902-1:2009 LIFTING AND LOAD-BEARING EQUIPMENT FOR STAGES AND OTHER PRODUCTION AREAS WITHIN THE ENTERTAINMENT INDUSTRY - PART 1: GENERAL REQUIREMENTS (EXCLUDING ALUMINIUM AND STEEL TRUSSES AND TOWERS)
    I.S. EN 14492-2:2006 CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 2: POWER DRIVEN HOISTS
    IEC TS 60034-25:2014 Rotating electrical machines - Part 25: AC electrical machines used in power drive systems - Application guide
    IEC 60204-33:2009 Safety of machinery - Electrical equipment of machines - Part 33: Requirements for semiconductor fabrication equipment
    I.S. EN 15268:2008 PETROL FILLING STATIONS - SAFETY REQUIREMENTS FOR THE CONSTRUCTION OF SUBMERSIBLE PUMP ASSEMBLIES
    DIN EN 12101-3:2015-12 SMOKE AND HEAT CONTROL SYSTEMS - PART 3: SPECIFICATION FOR POWERED SMOKE AND HEAT CONTROL VENTILATORS (FANS)
    DIN EN ISO 8528-13 E : 2017 RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 13: SAFETY (ISO 8528-13:2016, CORRECTED VERSION 2016-10-15)
    DIN EN 327:2014-11 HEAT EXCHANGERS - FORCED CONVECTION AIR COOLED REFRIGERANT CONDENSERS - TEST PROCEDURES FOR ESTABLISHING PERFORMANCE
    DIN EN ISO 8528-13:2014-09 (Draft) RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 13: SAFETY (ISO 8528-13:2016, CORRECTED VERSION 2016-10-15)
    UNE-EN 50216-12:2011 Power transformer and reactor fittings - Part 12: Fans
    BS EN ISO 13709:2003 Centrifugal pumps for petroleum, petrochemical and natural gas industries
    IEC 60349-2:2010 Electric traction - Rotating electrical machines for rail and road vehicles - Part 2: Electronic converter-fed alternating current motors
    UNE-EN 12101-3:2016 Smoke and heat control systems - Part 3: Specification for powered smoke and heat control ventilators (Fans)
    BS EN 1175-1 : 1998 SAFETY OF INDUSTRIAL TRUCKS - ELECTRICAL REQUIREMENTS - PART 1: GENERAL REQUIREMENTS FOR BATTERY POWERED TRUCKS
    BS EN 61800-1:1998 Adjustable speed electrical power drive systems Rating specifications for low voltage adjustable speed d.c. power drive systems
    15/30286839 DC : 0 BS ISO 14990-3 - EARTH-MOVING MACHINERY - ELECTRICAL SAFETY OF MACHINES UTILISING ELECTRIC DRIVES AND RELATED COMPONENTS AND SYSTEMS - PART 3: PARTICULAR REQUIREMENTS FOR SELF-POWERED MACHINES
    IEC 60034-14:2003+AMD1:2007 CSV Rotating electrical machines - Part 14: Mechanical vibration of certain machines with shaft heights 56 mm and higher - Measurement, evaluation and limits of vibration severity
    ISO 19859:2016 Gas turbine applications Requirements for power generation
    09/30206527 DC : 0 BS EN 60079-0 ED 6.0 - EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS
    BIS IS/IEC 60079-0 : 2011 EXPLOSIVE ATMOSPHERES - PART 0: GENERAL REQUIREMENTS
    I.S. EN 327:2014 HEAT EXCHANGERS - FORCED CONVECTION AIR COOLED REFRIGERANT CONDENSERS - TEST PROCEDURE FOR ESTABLISHING PERFORMANCE
    I.S. EN ISO 14224:2016 PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - COLLECTION AND EXCHANGE OF RELIABILITY AND MAINTENANCE DATA FOR EQUIPMENT (ISO 14224:2016)
    I.S. EN 14492-1:2006 CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 1: POWER DRIVEN WINCHES
    DIN EN 14492-1:2010-06 Cranes - Power driven winches and hoists - Part 1: Power driven winches (includes Amendment A1:2009)
    EN 61800-1:1998 Adjustable speed electrical power drive systems - Part 1: General requirements - Rating specifications for low voltage adjustable speed d.c. power drive systems
    I.S. EN 14161:2011 PETROLEUM AND NATURAL GAS INDUSTRIES - PIPELINE TRANSPORTATION SYSTEMS (ISO 13623:2009 MODIFIED)
    DIN EN 13135-1:2004-05 CRANES - EQUIPMENT - PART 1: ELECTROTECHNICAL EQUIPMENT
    I.S. EN 328:2014 HEAT EXCHANGERS - FORCED CONVECTION UNIT AIR COOLERS FOR REFRIGERATION - TEST PROCEDURES FOR ESTABLISHING THE PERFORMANCE
    I.S. EN 12101-3:2015 SMOKE AND HEAT CONTROL SYSTEMS - PART 3: SPECIFICATION FOR POWERED SMOKE AND HEAT CONTROL VENTILATORS (FANS)
    ISA 60079-7 : 2008 EXPLOSIVE ATMOSPHERES - PART 7: EQUIPMENT PROTECTION BY INCREASED SAFETY "E"
    EN 50216-7:2002 Power transformer and reactor fittings - Part 7: Electric pumps for transformer oil
    EN 50216-12:2011 Power transformer and reactor fittings - Part 12: Fans
    I.S. EN ISO 1680:2013 ACOUSTICS - TEST CODE FOR THE MEASUREMENT OF AIRBORNE NOISE EMITTED BY ROTATING ELECTRICAL MACHINES (ISO 1680:2013)
    EN 60079-14:2014/AC:2016 EXPLOSIVE ATMOSPHERES - PART 14: ELECTRICAL INSTALLATIONS DESIGN, SELECTION AND ERECTION (IEC 60079-14:2013/COR1:2016)
    DIN EN 61800-1 : 1999-08 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 1: GENERAL REQUIREMENTS; RATING SPECIFICATIONS FOR LOW VOLTAGE ADJUSTABLE SPEED D.C. POWER DRIVE SYSTEMS
    EN 60079-15:2010 Explosive atmospheres - Part 15: Equipment protection by type of protection "n"
    VDE 0160-101 : 1999-08 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - GENERAL REQUIREMENTS - RATING SPECIFICATIONS FOR LOW VOLTAGE ADJUSTABLE SPEED D.C. POWER DRIVE SYSTEMS
    IEC 61058-1:2016 RLV Switches for appliances - Part 1: General requirements
    I.S. EN 1175-1:1998 SAFETY OF INDUSTRIAL TRUCKS - ELECTRICAL REQUIREMENTS - PART 1: GENERAL REQUIREMENTS FOR BATTERY POWERED TRUCKS
    BIS IS/IEC 61058-1 : 2000(R2007) SWITCHES FOR APPLIANCES - PART 1: GENERAL REQUIREMENTS
    NEMA ICS 20:2009 (R2015) Informational Guide to Electrical Industrial Topics
    VDE 0530-15 : 2010 ROTATING ELECTRICAL MACHINES - PART 15: IMPULSE VOLTAGE WITHSTAND LEVELS OF FORM-WOUND STATOR COILS FOR ROTATING A.C. MACHINES
    VDE 0530 SUPP 2 : 1999 ROTATING ELECTRICAL MACHINES - PART 17: CAGE INDUCTION MOTORS WHEN FED FROM CONVERTERS - APPLICATION GUIDE
    BIS IS/ISO 8528-8 : 1995(R2014) RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 8: REQUIREMENTS AND TESTS FOR LOW-POWER GENERATING SETS
    KTA 3504 : 2015(R2017)
    NBR IEC 60034-5 : 2009 ROTATING ELECTRICAL MACHINES - PART 5: DEGREES OF PROTECTION PROVIDED BY THE INTEGRAL DESIGN OF ROTATING ELECTRICAL MACHINES (IP CODE) - CLASSIFICATION
    VDI/VDE 3680:2002-10 Control of synchronous machines
    CEI CLC/TS 50537-3 : 2011 RAILWAY APPLICATIONS - MOUNTED PARTS OF THE TRACTION TRANSFORMER AND COOLING SYSTEM - PART 3: WATER PUMP FOR TRACTION CONVERTERS
    CEI EN 88528-11 : 2005 RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 11: ROTARY UNINTERRUPTIBLE POWER SYSTEMS - PERFORMANCE REQUIREMENTS AND TEST METHODS
    08/30176387 DC : DRAFT JAN 2008 BS EN 60034-18-21 - ROTATING ELECTRICAL MACHINES - PART 18-21: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR WIRE-WOUND WINDINGS - THERMAL EVALUATION AND CLASSIFICATION
    09/30152273 DC : 0 BS IEC/TS 60034-20-2 - ROTATING ELECTRICAL MACHINES - PART 20-2: PERFORMANCE CHARACTERISTICS AND TESTING SPECIFICATIONS FOR BRUSHLESS PERMANENT MAGNET MOTORS
    13/30268505 DC : 0 BS ISO 21873-1 - BUILDING CONSTRUCTION MACHINERY AND EQUIPMENT - MOBILE CRUSHERS - PART 1: TERMINOLOGY AND COMMERCIAL SPECIFICATIONS
    15/30324519 DC : 0 BS EN ISO 14224 - PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - COLLECTION AND EXCHANGE OF RELIABILITY AND MAINTENANCE DATA FOR EQUIPMENT
    DEFSTAN 02-607/3(2013) : 2013 DESIGN OF HIGH VOLTAGE ELECTRICAL POWER SYSTEMS FOR HM SHIPS, SUBMARINES AND THE ROYAL FLEET AUXILIARY
    I.S. EN 1151-1:2006 PUMPS - ROTODYNAMIC PUMPS - CIRCULATION PUMPS HAVING A RATED POWER INPUT NOT EXCEEDING 200 W FOR HEATING INSTALLATIONS AND DOMESTIC HOT WATER INSTALLATIONS - PART 1: NON-AUTOMATIC CIRCULATION PUMPS, REQUIREMENTS, TESTING, MARKING
    BS ISO 50004:2014 Energy management systems. Guidance for the implementation, maintenance and improvement of an energy management system
    15/30314548 DC : 0 BS EN 61800-9-2 - ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 9-2: ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS & THEIR DRIVEN APPLICATIONS - ENERGY EFFICIENCY INDICATORS FOR POWER DRIVE SYSTEMS AND MOTOR STARTERS
    UNI EN 12693 : 2008 REFRIGERATING SYSTEMS AND HEAT PUMPS - SAFETY AND ENVIRONMENTAL REQUIREMENTS - POSITIVE DISPLACEMENT REFRIGERANT COMPRESSORS
    09/30182105 DC : 0 BS EN 60349-2 - ELECTRICAL TRACTION - ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 2: ELECTRONIC CONVERTER-FED ALTERNATING CURRENT MOTORS
    PD IEC/TR 62001-1:2016 High-voltage direct current (HVDC) systems. Guidance to the specification and design evaluation of AC filters Overview
    12/30269385 DC : 0 BS EN 327 - HEAT EXCHANGERS - FORCED CONVECTION AIR COOLED REFRIGERANT CONDENSERS - TEST PROCEDURES FOR ESTABLISHING PERFORMANCE
    BS EN 60349-2:2010 Electrical traction. Rotating electrical machines for rail and road vehicles Electronic converter-fed alternating current motors
    BS EN 60034-18-31:2012 Rotating electrical machines Functional evaluation of insulation systems. Test procedures for form-wound windings. Thermal evaluation and classification of insulation systems used in rotating machines
    BIS IS/ISO 8528-12 : 1997(R2014) RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 12: EMERGENCY POWER SUPPLY TO SAFETY SERVICES
    UNI ISO 13380 : 2010 CONDITION MONITORING AND DIAGNOSTICS OF MACHINES - GENERAL GUIDELINES ON USING PERFORMANCE PARAMETERS
    NF EN 61116 : 2003 ELECTROMECHANICAL EQUIPMENT GUIDE FOR SMALL HYDROELECTRIC INSTALLATIONS
    DD IEC/TS 60034-17:2006 Rotating electrical machines Cage induction motors when fed from converters. Application guide
    BS IEC 61892-3:2012 Mobile and fixed offshore units. Electrical installations Equipment
    I.S. EN 60349-1:2010 ELECTRIC TRACTION - ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 1: MACHINES OTHER THAN ELECTRONIC CONVERTOR-FED ALTERNATING CURRENT MOTORS
    05/30138880 DC : DRAFT SEP 2005 IEC 61986 ED 2 - ROTATING ELECTRICAL EQUIPMENT - EQUIVALENT LOADING AND SUPER-POSITIONING TECHNIQUES - INDIRECT TESTING TO DETERMINE TEMPERATURE RISE
    BS EN 60034-28:2013 Rotating electrical machines Test methods for determining quantities of equivalent circuit diagrams for three-phase low-voltage cage induction motors
    BS 848-3(2001) : 2001 FANS FOR GENERAL PURPOSE - PART 3: PERFORMANCE TESTING IN SITU
    ISO 13707:2000 Petroleum and natural gas industries Reciprocating compressors
    BS 7698-12:1998 Reciprocating internal combustion engine driven alternating current generating sets Emergency power supply to safety devices
    BS EN 60034-29:2008 Rotating electrical machines Equivalent loading and superposition techniques. Indirect testing to determine temperature rise
    08/30184920 DC : DRAFT JULY 2008 BS EN 60034-18-31 - ROTATING ELECTRICAL MACHINES - PART 18-31: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR FORM-WOUND WINDINGS - THERMAL EVALUATION AND CLASSIFICATION OF INSULATION SYSTEMS USED IN ROTATING MACHINES
    DIN ISO 17359:2011-09 CONDITION MONITORING AND DIAGNOSTICS OF MACHINES - GENERAL GUIDELINES
    BS EN 61800-4:2003 Adjustable speed electrical power drive systems General requirements. Rating specifications for a.c. power drive systems above 1000 V a.c. and not exceeding 35 kV
    BS EN 61241-4:2006 Electrical apparatus for use in the presence of combustible dust Type of protection \'pD\'
    PREN 14492-1 : DRAFT 2015 CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 1: POWER DRIVEN WINCHES
    BS EN ISO 5801:2017 Fans. Performance testing using standardized airways
    08/30176298 DC : DRAFT JAN 2008 BS EN 62477-1 - SAFETY REQUIREMENTS FOR POWER SEMICONDUCTOR CONVERTER SYSTEMS - PART 1: GENERAL
    14/30278882 DC : 0 BS EN 60079-7 IEC 60079-7 ED. 5.0 - EXPLOSIVE ATMOSPHERES - PART 7: EQUIPMENT PROTECTION BY INCREASED SAFETY 'E'
    09/30205068 DC : 0 BS EN 1151-1 - PUMPS - ROTODYNAMIC PUMPS - CIRCULATION PUMPS HAVING A RATED POWER INPUT NOT EXCEEDING 200 W FOR HEATING INSTALLATIONS AND DOMESTIC HOT WATER INSTALLATIONS - PART 1: GENERAL REQUIREMENTS, TESTING, MARKING
    EN ISO 5801:2017 Fans - Performance testing using standardized airways (ISO 5801:2017)
    NF EN 60034-8 : 2008 AMD 1 2014 ROTATING ELECTRICAL MACHINES - PART 8: TERMINAL MARKINGS AND DIRECTION OF ROTATION
    BS 7458-2:1991 Test code for the measurement of airborne noise emitted by rotating electrical machinery Survey method
    BS IEC 61241-4:2001 Electrical apparatus for use in the presence of combustible dust Type of protection \'pD\'
    BS EN 15714-2:2009 Industrial valves. Actuators Electric actuators for industrial valves. Basic requirements
    DIN EN 15268 E : 2008 PETROL FILLING STATIONS - SAFETY REQUIREMENTS FOR THE CONSTRUCTION OF SUBMERSIBLE PUMP ASSEMBLIES
    13/30252783 DC : 0 BS EN 50502 - RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRIC EQUIPMENT IN TROLLEY BUSES - SAFETY REQUIREMENTS AND CONNECTION SYSTEMS
    17/30341578 DC : DRAFT MAY 2017 BS ISO 17359 - CONDITION MONITORING AND DIAGNOSTICS OF MACHINES - GENERAL GUIDELINES
    13/30248785 DC : 0 BS EN 61800-2 - ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 2: GENERAL REQUIREMENTS - RATING SPECIFICATIONS FOR LOW VOLTAGE ADJUSTABLE FREQUENCY A.C. POWER DRIVE SYSTEMS
    10/30238295 DC : 0 BS EN 60034-28 - ROTATING ELECTRICAL MACHINES - PART 28: TEST METHODS FOR DETERMINING QUANTITIES OF EQUIVALENT CIRCUIT DIAGRAMS FOR THREE-PHASE LOW-VOLTAGE CAGE INDUCTION MOTORS
    13/30280184 DC : 0 BS EN 50598-1 - ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS & THEIR DRIVEN APPLICATIONS - PART 1: GENERAL REQUIREMENTS FOR SETTING ENERGY EFFICIENCY STANDARDS FOR POWER DRIVEN EQUIPMENT USING THE EXTENDED PRODUCT APPROACH (EPA), AND SEMI ANALYTIC MODEL (SAM)
    02/207221 DC : DRAFT JULY 2002 IEC 60079-1 ED.5 - ELECTRICAL APPARATUS FOR EXPLOSIVE GAS ATMOSPHERES - PART 1: FLAMEPROOF ENCLOSURES "D"
    BS EN 60034-14:2004 Rotating electrical machines Mechanical vibration of certain machines with shaft heights 56 mm and higher. Measurement, evaluation and limits of vibration severity
    UNE-EN 61400-2:2015 Wind turbines - Part 2: Small wind turbines
    ISA 61241-2 : 2006 ELECTRICAL APPARATUS FOR USE IN ZONE 21 AND ZONE 22 HAZARDOUS (CLASSIFIED) LOCATIONS - PROTECTION BY PRESSURIZATION "PD"
    BS EN 60034-30-1:2014 Rotating electrical machines Efficiency classes of line operated AC motors (IE code)
    NF EN ISO 5802 : 2009 AMD 1 2015 INDUSTRIAL FANS - PERFORMANCE TESTING IN SITU
    PD IEC/TS 60034-30-2:2016 Rotating electrical machines Efficiency classes of variable speed AC motors (IE-code)
    I.S. EN 60034-22:2009 ROTATING ELECTRICAL MACHINES - PART 22: AC GENERATORS FOR RECIPROCATING INTERNAL COMBUSTION (RIC) ENGINE DRIVEN GENERATING SETS
    BS 7458-1:1991 Test code for the measurement of airborne noise emitted by rotating electrical machinery Engineering method for free-field conditions over a reflecting plane
    DD IEC/PAS 62001:2004 Guide to the specification and design evaluation of a.c. filters for HVDC systems
    I.S. EN 50216-12:2011 POWER TRANSFORMER AND REACTOR FITTINGS - PART 12: FANS
    IEEE DRAFT C37.102 : D8 2006 AC GENERATOR PROTECTION
    I.S. EN ISO 5801:2017 FANS - PERFORMANCE TESTING USING STANDARDIZED AIRWAYS (ISO 5801: 2017)
    06/30151149 DC : DRAFT JUN 2006 BS IEC 60034-3 - ROTATING ELECTRICAL MACHINES - PART 3: SPECIFIC REQUIREMENTS FOR SYNCHRONOUS GENERATORS DRIVEN BY STEAM TURBINES OR COMBUSTION GAS TURBINES
    NF EN 88528-11 : 2005 RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 11: ROTARY UNINTERRUPTIBLE POWER SYSTEMS - PERFORMANCE REQUIREMENTS AND TEST METHODS
    API 616 REDLINE : 2011 GAS TURBINES FOR THE PETROLEUM, CHEMICAL, AND GAS INDUSTRY SERVICES
    I.S. EN 60079-1:2014 EXPLOSIVE ATMOSPHERES - PART 1: EQUIPMENT PROTECTION BY FLAMEPROOF ENCLOSURES 'D'
    IEC 61936-1:2010+AMD1:2014 CSV Power installations exceeding 1 kV a.c. - Part 1: Common rules
    CEI EN 60349-2 : 2012 ELECTRIC TRACTION - ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 2: ELECTRONIC CONVERTER-FED ALTERNATING CURRENT MOTORS
    NF EN 60947 6-2 : 2003 AMD 1 2007 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 6-2: MULTIPLE FUNCTION EQUIPMENT - CONTROL AND PROTECTIVE SWITCHING DEVICES (OR EQUIPMENT) (CPS)
    I.S. EN 60079-7:2015 EXPLOSIVE ATMOSPHERES - PART 7: EQUIPMENT PROTECTION BY INCREASED SAFETY 'E'
    IEEE C50.13 : 2014 CYLINDRICAL-ROTOR 50 HZ AND 60 HZ, SYNCHRONOUS GENERATORS RATED 10 MVA AND ABOVE
    BS IEC 60092-501:2013 Electrical installations in ships Special features. Electric propulsion plant
    I.S. EN 50216-7:2002 POWER TRANSFORMER AND REACTOR FITTINGS - PART 7: ELECTRIC PUMPS FOR TRANSFORMER OIL
    CEI EN 60034-18-42 : 1ED 2017 ROTATING ELECTRICAL MACHINES - PART 18-42: PARTIAL DISCHARGE RESISTANT ELECTRICAL INSULATION SYSTEMS (TYPE 2) USED IN ROTATING ELECTRICAL MACHINES FED FROM VOLTAGE CONVERTERS - QUALIFICATION TESTS
    IEEE C37.102-2006 REDLINE IEEE Guide for AC Generator Protection
    CSA C61400-2 : 2008 : R2013 WIND TURBINES - PART 2: DESIGN REQUIREMENTS FOR SMALL WIND TURBINES
    OVE/ONORM EN 60034-3 : 2009 ROTATING ELECTRICAL MACHINES - PART 3: SPECIFIC REQUIREMENTS FOR SYNCHRONOUS GENERATORS DRIVEN BY STEAM TURBINES OR COMBUSTION GAS TURBINES
    IEC TR 61000-3-15:2011 Electromagnetic compatibility (EMC) - Part 3-15: Limits - Assessment of low frequency electromagnetic immunity and emission requirements for dispersed generation systems in LV network
    BS EN 62271-1:2017 High-voltage switchgear and controlgear Common specifications for alternating current switchgear and controlgear
    BS EN 60335-1 : 2012 HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60335-1:2010, MODIFIED)
    BS EN 60034-8 : 2007 ROTATING ELECTRICAL MACHINES - PART 8: TERMINAL MARKINGS AND DIRECTION OF ROTATION
    UNE-EN 50598-1:2015 Ecodesign for power drive systems, motor starters, power electronics & their driven applications - Part 1: General requirements for setting energy efficiency standards for power driven equipment using the extended product approach (EPA), and semi analytic model (SAM)
    ISO 8528-8:2016 Reciprocating internal combustion engine driven alternating current generating sets — Part 8: Requirements and tests for low-power generating sets
    IEC 60092-204:1987 Electrical installations in ships. Part 204: System design - Electric and electrohydraulic steering gear
    IEC 61892-5:2014 Mobile and fixed offshore units - Electrical installations - Part 5: Mobile units
    BIS IS/IEC 62271-1 : 2007 HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 1: COMMON SPECIFICATIONS
    BS EN 60079-15:2010 Explosive atmospheres Equipment protection by type of protection \'n\'
    PREN 327 : DRAFT 2012 HEAT EXCHANGERS - FORCED CONVECTION AIR COOLED REFRIGERANT CONDENSERS - TEST PROCEDURES FOR ESTABLISHING PERFORMANCE
    I.S. EN 61400-2:2014 WIND TURBINES - PART 2: SMALL WIND TURBINES
    EN 60034-18-42:2017 Rotating electrical machines - Part 18-42: Partial discharge resistant electrical insulation systems (Type II) used in rotating electrical machines fed from voltage converters - Qualification tests
    IEC 60947-4-1:2009+AMD1:2012 CSV Low-voltage switchgear and controlgear - Part 4-1: Contactors and motor-starters - Electromechanical contactors and motor-starters
    IEC TS 60034-31:2010 Rotating electrical machines - Part 31: Selection of energy-efficient motors including variable speed applications - Application guide
    IEC 60092-301:1980 Electrical installations in ships - Part 301: Equipment - Generators and motors
    I.S. EN 15194:2017 CYCLES - ELECTRICALLY POWER ASSISTED CYCLES - EPAC BICYCLES
    IEC TS 62257-7-3:2008 Recommendations for small renewable energy and hybrid systems for rural electrification - Part 7-3: Generator set - Selection of generator sets for rural electrification systems
    IEC 61800-9-1:2017 Adjustable speed electrical power drive systems - Part 9-1: Ecodesign for power drive systems, motor starters, power electronics and their driven applications - General requirements for setting energy efficiency standards for power driven equipment using the extended product approach (EPA) and semi analytic model (SAM)
    IEC TS 60034-23:2003 Rotating electrical machines - Part 23: Specification for the refurbishing of rotating electrical machines
    IEC 60034-18-42:2017 Rotating electrical machines - Part 18-42: Partial discharge resistant electrical insulation systems (Type II) used in rotating electrical machines fed from voltage converters - Qualification tests
    IEC 61892-3:2012 Mobile and fixed offshore units - Electrical installations - Part 3: Equipment
    I.S. EN 60204-1:2006 SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS
    IEC 60204-11:2000 Safety of machinery - Electrical equipment of machines - Part 11: Requirements for HV equipment for voltages above 1 000 V a.c. or 1 500 V d.c. and not exceeding 36 kV
    DIN EN ISO 1680:2014-04 ACOUSTICS - TEST CODE FOR THE MEASUREMENT OF AIRBORNE NOISE EMITTED BY ROTATING ELECTRICAL MACHINES (ISO 1680:2013)
    UNE-EN 60349-2:2011 Electric traction - Rotating electrical machines for rail and road vehicles -- Part 2: Electronic converter-fed alternating current motors
    IEC 60034-18-32:2010 Rotating electrical machines - Part 18-32: Functional evaluation of insulation systems - Test procedures for form-wound windings - Evaluation by electrical endurance
    IEC 60034-22:2009 Rotating electrical machines - Part 22: AC generators for reciprocating internal combustion (RIC) engine driven generating sets
    IEC 60034-8:2007+AMD1:2014 CSV Rotating electrical machines - Part 8: Terminal markings anddirection of rotation
    UNE-EN 60079-14:2016 Explosive atmospheres - Part 14: Electrical installations design, selection and erection
    UNE-EN 60947-4-1:2011 Low-voltage switchgear and controlgear - Part 4-1: Contactors and motor-starters - Electromechanical contactors and motor-starters
    IEC 60034-19:2014 Rotating electrical machines - Part 19: Specific test methods for d.c. machines on conventional and rectifier-fed supplies
    ISO 5802:2001 Industrial fans — Performance testing in situ
    IEC 60034-3:2007 Rotating electrical machines - Part 3: Specific requirements for synchronous generators driven by steam turbines or combustion gas turbines
    IEC 61800-4:2002 Adjustable speed electrical power drive systems - Part 4: General requirements - Rating specifications for a.c. power drive systems above 1 000 V a.c. and not exceeding 35 kV
    BS EN 61800-5-1:2007 Adjustable speed electrical power drive systems Safety requirements. Electrical, thermal and energy
    IEC 88528-11:2004 Reciprocating internal combustion engine driven alternating current generating sets - Part 11: Rotary uninterruptible power systems - Performance requirements and test methods
    BS EN 60079-14:2014 Explosive atmospheres Electrical installations design, selection and erection
    ISO 14224:2016 Petroleum, petrochemical and natural gas industries Collection and exchange of reliability and maintenance data for equipment
    ISO 8528-13:2016 Reciprocating internal combustion engine driven alternating current generating sets — Part 13: Safety
    BS EN 1151-1:2006 Pumps. Rotodynamic pumps. Circulation pumps having a rated power input not exceeding 200 W for heating installations and domestic hot water installations Non-automatic circulation pumps, requirements, testing, marking
    EN 60034-5:2001/A1:2007 ROTATING ELECTRICAL MACHINES - PART 5: DEGREES OF PROTECTION PROVIDED BY THE INTEGRAL DESIGN OF ROTATING ELECTRICAL MACHINES (IP CODE) - CLASSIFICATION
    EN ISO 8528-13:2016 Reciprocating internal combustion engine driven alternating current generating sets - Part 13: Safety (ISO 8528-13:2016, Corrected version 2016-10-15)
    CSA C22.2 No. 60335-1:2011 SAFETY OF HOUSEHOLD AND SIMILAR APPLIANCES - PART 1: GENERAL REQUIREMENTS
    UNE-EN 61400-22:2011 Wind turbines - Part 22: Conformity testing and certification
    EN 60034-3:2008 Rotating electrical machines - Part 3: Specific requirements for synchronous generators driven by steam turbines or combustion gas turbines
    UNE-EN 60204-1:2007 Safety of machinery - Electrical equipment of machines - Part 1: General requirements
    CAN/CSA-C22.2 NO. 60335-1:11 (R2016) Safety of household and similar appliances - Part 1: General requirements (Tri-national standard, with NMX-J-521/1-ANCE and UL 60335-1)
    UL 60335-1:6ED 2016-10 Standard for Safety of Household and Similar Appliances, Part 1: General Requirements
    EN 50016:2002 Electrical apparatus for potentially explosive atmospheres - Pressurized apparatus "p"
    UNI EN 1175-1 : 2010 SAFETY OF INDUSTRIAL TRUCKS - ELECTRICAL REQUIREMENTS - PART 1: GENERAL REQUIREMENTS FOR BATTERY POWERED TRUCKS
    UNI EN 14492-2 : 2009 CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 2: POWER DRIVEN HOISTS
    UNI EN ISO 15783 : 2009 Seal-less rotodynamic pumps - Class II - Specification
    CSA C22.2 No. 60079.1 : 2016 EXPLOSIVE ATMOSPHERES - PART 1: EQUIPMENT PROTECTION BY FLAMEPROOF ENCLOSURES 'D'
    UNI EN 14492-1 : 2009 CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 1: POWER DRIVEN WINCHES
    EN 50281-1-1 : 98 AMD 1 2002 ELECTRICAL APPARATUS PROTECTED BY ENCLOSURES - CONSTRUCTION AND TESTING FOR USE IN THE PRESENCE OF COMBUSTIBLE DUST - ELECTRICAL APPARATUS PROTECTED BY ENCLOSURES - CONSTRUCTION AND TESTING
    UNI EN 13135-1 : 2010 CRANES - EQUIPMENT - PART 1: ELECTROTECHNICAL EQUIPMENT
    UNI EN ISO 1680 : 2014 ACOUSTICS - TEST CODE FOR THE MEASUREMENT OF AIRBORNE NOISE EMITTED BY ROTATING ELECTRICAL MACHINES
    UNE-EN 60349-4:2013 Electric traction - Rotating electrical machines for rail and road vehicles - Part 4: Permanent magnet synchronous electrical machines connected to an electronic converter
    BS 7698-4:1993 Reciprocating internal combustion engine driven alternating current generating sets Specification for controlgear and switchgear
    13/30288508 DC : 0 BS IEC 60034-27-3 ED 1.0 - ROTATING ELECTRICAL MACHINES - PART 27-3: DIELECTRIC DISSIPATION FACTOR MEASUREMENT ON STATOR WINDING INSULATION OF ROTATING ELECTRICAL MACHINES
    DD IEC TS 60034-20-1 : 2002 AMD 16729 ROTATING ELECTRICAL MACHINES - CONTROL MOTORS - STEPPING MOTORS
    BIS IS/IEC 60947-4-2 : 1999 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 4: CONTRACTORS AND MOTOR-STARTERS - SECTION 2: AC SEMICONDUCTOR MOTOR CONTROLLERS AND STARTERS
    BS EN 60947-4-1 : 2010 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 4-1: CONTACTORS AND MOTOR-STARTERS - ELECTROMECHANICAL CONTACTORS AND MOTOR-STARTERS
    I.S. EN 60034-18-31:2012 ROTATING ELECTRICAL MACHINES - PART 18-31: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR FORM-WOUND WINDINGS - THERMAL EVALUATION AND CLASSIFICATION OF INSULATION SYSTEMS USED IN ROTATING MACHINES (IEC 60034-18-31:2012 (EQV))
    BS 7698-1:1993 Reciprocating internal combustion engine driven alternating current generating sets Specification for application, ratings and performance
    I.S. EN 60204-11:2000 SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES PART 11: REQUIREMENTS FOR HV EQUIPMENT FOR VOLTAGES ABOVE 1000 V A.C. OR 1500 V D.C. AND NOT EXCEEDING 36 KV
    NF ISO 8528-3 : 2005 RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 3: ALTERNATING CURRENT GENERATORS FOR GENERATING SETS
    BS EN 60034-30:2009 Rotating electrical machines Efficiency classes of single-speed, three-phase, cage-induction motors (IE-code)
    12/30269388 DC : 0 BS EN 328 - HEAT EXCHANGERS - FORCED CONVECTION UNIT AIR COOLERS FOR REFRIGERATION - TEST PROCEDURES FOR ESTABLISHING THE PERFORMANCE
    CEI EN 60027-4 : 2008 LETTER SYMBOLS TO BE USED IN ELECTRICAL TECHNOLOGY - PART 4: ROTATING ELECTRICAL MACHINES
    07/30168628 DC : 0 BS EN 60079-15 - EXPLOSIVE ATMOSPHERES - PART 15: EQUIPMENT PROTECTION BY TYPE OF PROTECTION "N"
    SANS 60034-26 : 2ED 2006(R2011) ROTATING ELECTRICAL MACHINES - PART 26: EFFECTS OF UNBALANCED VOLTAGES ON THE PERFORMANCE OF THREE-PHASE CAGE INDUCTION MOTORS
    EN 15714-2:2009 Industrial valves - Actuators - Part 2: Electric actuators for industrial valves - Basic requirements
    BS EN 60034-2-1:2014 Rotating electrical machines Standard methods for determining losses and efficiency from tests (excluding machines for traction vehicles)
    EN 61800-9-1:2017 Adjustable speed electrical power drive systems - Part 9-1: Ecodesign for power drive systems, motor starters, power electronics and their driven applications - General requirements for setting energy efficiency standards for power driven equipment using the extended product approach (EPA) and semi analytic model (SAM)
    PREN 1175 : DRAFT 2017 SAFETY OF INDUSTRIAL TRUCKS - ELECTRICAL/ELECTRONIC REQUIREMENTS
    01/202922 DC : DRAFT APR 2001 IEC 60034-23 ED.1 - ROTATING ELECTRICAL MACHINES - PART 23: SPECIFICATION FOR THE REFURBISHING OF ROTATING ELECTRICAL MACHINES
    BS 7698-3:1993 Reciprocating internal combustion engine driven alternating current generating sets Specification for alternating current generators for generating sets
    BS ISO 21873-1:2015 Building construction machinery and equipment. Mobile crushers Terminology and commercial specifications
    06/30148073 DC : DRAFT MAR 2006 IEC 61400-21 - WIND TURBINES - PART 21: MEASUREMENT AND ASSESSMENT OF POWER QUALITY CHARACTERISTICS OF GRID CONNECTED WIND TURBINES
    04/30113660 DC : DRAFT MAY 2004 IEC 60079-7 - ELECTRICAL APPARATUS FOR EXPLOSIVE GAS ATMOSPHERES - PART 7: INCREASED SAFETY 'E'
    BS EN 60034-19:2014 Rotating electrical machines Specific test methods for d.c. machines on conventional and rectifier-fed supplies
    S.R. CLC/TS 60034-25:2008 ROTATING ELECTRICAL MACHINES - PART 25: GUIDANCE FOR THE DESIGN AND PERFORMANCE OF A.C. MOTORS SPECIFICALLY DESIGNED FOR CONVERTER SUPPLY
    BS EN 60034-11:2004 Rotating electrical machines Thermal protection
    BIS IS/ISO 8528-3 : 2005(R2014) RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 3: ALTERNATING CURRENT GENERATORS FOR GENERATING SETS
    BS 7698-5:1993 Reciprocating internal combustion engine driven alternating current generating sets Specification for generating sets
    UNI EN 15714-2 : 2009 INDUSTRIAL VALVES - ACTUATORS - PART 2: ELECTRIC ACTUATORS FOR INDUSTRIAL VALVES - BASIC REQUIREMENTS
    DD CLC/TS 60034-31:2011 Rotating electrical machines Selection of energy-efficient motors including variable speed applications. Application guide
    05/30139105 DC : DRAFT SEP 2005 IEC 61800-5-1 ED 2 - ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 5-1: SAFETY REQUIREMENTS - ELECTRICAL, THERMAL AND ENERGY
    IEC TR 62001:2009 High-voltage direct current (HVDC) systems - Guidebook to the specification and design evaluation of A.C. filters
    07/30161347 DC : 0 BS EN 60034-30 - ROTATING ELECTRICAL MACHINES - PART 30: EFFICIENCY CLASSES OF SINGLE-SPEED THREE-PHASE CAGE INDUCTION MOTORS
    IEEE 95-2002 IEEE Recommended Practice for Insulation Testing of AC Electric Machinery (2300 V and Above) With High Direct Voltage
    VDE 0160-109-1 : 2018-01 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 9-1: ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS AND THEIR DRIVEN APPLICATIONS - GENERAL REQUIREMENTS FOR SETTING ENERGY EFFICIENCY STANDARDS FOR POWER DRIVEN EQUIPMENT USING THE EXTENDED PRODUCT APPROACH (EPA) AND SEMI ANALYTIC MODEL (SAM)
    IEC 60079-0:2017 Explosive atmospheres - Part 0: Equipment - General requirements
    I.S. EN 60947-6-2:2003 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - MULTIPLE FUNCTION EQUIPMENT - CONTROL AND PROTECTIVE SWITCHING DEVICES (OR EQUIPMENT) (CPS)
    14/30284736 DC : 0 BS EN ISO 5801 - FANS - PERFORMANCE TESTING USING STANDARDIZED AIRWAYS
    DIN ISO 8528-4:1997-11 RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 4: CONTROL AND SWITCHGEAR
    13/30280187 DC : 0 BS EN 50598-2 - ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS & THEIR DRIVEN APPLICATIONS - PART 2: ENERGY EFFICIENCY INDICATORS FOR POWER DRIVE SYSTEMS AND MOTOR STARTERS
    PD IEC/TR 61000-3-15:2011 Electromagnetic compatibility (EMC) Limits. Assessment of low frequency electromagnetic immunity and emission requirements for dispersed generation systems in LV network
    BS EN 60034-18-32:2010 Rotating electrical machines Functional evaluation of insulation systems. Test procedures for form-wound windings. Evaluation by electrical endurance
    CSA C22.2 No. 60079.1 : 2016 EXPLOSIVE ATMOSPHERES - PART 1: EQUIPMENT PROTECTION BY FLAMEPROOF ENCLOSURES 'D'
    IEC 60079-7:2015+AMD1:2017 CSV Explosive atmospheres - Part 7: Equipment protection by increased safety "e"
    BS EN 60034-5:2001 Rotating electrical machines Degrees of protection provided by the integral design of rotating electrical machines (IP code). Classification
    BS EN 60034-18-42:2017 Rotating electrical machines Partial discharge resistant electrical insulation systems (Type II) used in rotating electrical machines fed from voltage converters - Qualification tests
    CEI UNI EN 45510-2-5 : 2006 GUIDE FOR PROCUREMENT OF POWER STATION EQUIPMENT - PART 2-5: ELECTRICAL EQUIPMENT - MOTORS
    GOST R ISO 8528-4 : 2005 RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 4: CONTROLGEAR AND SWITCHGEAR
    DD CLC/TS 60034-20-1:2004 Rotating electrical machines. Control motors Stepping motors
    BS EN 60034-2-2:2010 Rotating electrical machines Specific methods for determining separate losses of large machines from tests. Supplement to IEC 60034-2-1
    04/30123544 DC : DRAFT OCT 2004 IEC 60079-1 - ELECTRICAL APPARATUS FOR EXPLOSIVE GAS ATMOSPHERES - PART 1: FLAMEPROOF ENCLOSURES 'D'
    DIN EN 15268:2008-11 PETROL FILLING STATIONS - SAFETY REQUIREMENTS FOR THE CONSTRUCTION OF SUBMERSIBLE PUMP
    NF EN 50016 : 2004 ELECTRICAL APPARATUS FOR POTENTIALLY EXPLOSIVE ATMOSPHERES - PRESSURIZED APPARATUS 'P'
    DIN VDE 0660-102 : 1992 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 4-1: ELECTROMECHANICAL CONTACTORS AND MOTOR-STARTERS
    I.S. EN 50598-1:2014 ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS & THEIR DRIVEN APPLICATIONS - PART 1: GENERAL REQUIREMENTS FOR SETTING ENERGY EFFICIENCY STANDARDS FOR POWER DRIVEN EQUIPMENT USING THE EXTENDED PRODUCT APPROACH (EPA), AND SEMI ANALYTIC MODEL (SAM)
    NF EN 60034-18-32 : 2011 ROTATING ELECTRICAL MACHINES - PART 18-32: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR FORM-WOUND WINDINGS - EVALUATION BY ELECTRICAL ENDURANCE
    CSA C22.2 No. 61058.1 : 2009 SWITCHES FOR APPLIANCES - PART 1: GENERAL REQUIREMENTS
    NF EN 60034-3 : 2008 ROTATING ELECTRICAL MACHINES - PART 3: SPECIFIC REQUIREMENTS FOR SYNCHRONOUS GENERATORS DRIVEN BY STEAM TURBINES OR COMBUSTION GAS TURBINES
    PREN 50502 : DRAFT 2013 RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRIC EQUIPMENT IN TROLLEY BUSES - SAFETY REQUIREMENTS AND CONNECTION SYSTEMS
    IEC 60079-1 REDLINE : 7ED 2014 EXPLOSIVE ATMOSPHERES - PART 1: EQUIPMENT PROTECTION BY FLAMEPROOF ENCLOSURES 'D'
    BS EN 60204-11 : 2001 SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 11: REQUIREMENTS FOR HV EQUIPMENT FOR VOLTAGES ABOVE 1000 V A.C. OR 1500 V D.C. AND NOT EXCEEDING 36 KV
    NF EN 60034-30 : 2009 ROTATING ELECTRICAL MACHINES - PART 30: EFFICIENCY CLASSES OF SINGLE-SPEED, THREE-PHASE, CAGE-INDUCTION MOTORS (IE-CODE)
    CSA C22.2 NO. 60947-4-1:14 (R2019) Low-voltage switchgear and controlgear - Part 4-1: Contactors and motor-starters - Electromechanical contactors and motor-starters ( Bi-national standard, with UL 60947-4-1)
    CSA C22.2 No. 60079-7 : 2016 EXPLOSIVE ATMOSPHERES - PART 7: EQUIPMENT PROTECTION BY INCREASED SAFETY 'E'
    UNE-EN 60947-4-2:2013 Low-voltage switchgear and controlgear - Part 4-2: Contactors and motor-starters - AC semiconductor motor controllers and starters
    CLC/TS 60034-18-34:2004 Rotating electrical machines - Part 18-34: Functional evaluation of insulation systems - Test procedures for form-wound windings - Evaluation of thermomechanical endurance of insulation systems
    API 546 : 2008 BRUSHLESS SYNCHRONOUS MACHINES - 500 KVA AND LARGER
    PREN 50598-2 : DRAFT 2013 ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS & THEIR DRIVEN APPLICATIONS - PART 2: ENERGY EFFICIENCY INDICATORS FOR POWER DRIVE SYSTEMS AND MOTOR STARTERS
    API 610 : 2010 CENTRIFUGAL PUMPS FOR PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES
    API 610 REDLINE : 2010 CENTRIFUGAL PUMPS FOR PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES
    CSA C22.2 NO. 60947-4-2:14 (R2019) Low-voltage switchgear and controlgear - Part 4-2: Contactors and motor-starters - AC semiconductor motor controllers and starters ( Bi-national standard, with UL 60947-4-2)
    NF EN 60034-18-34 : 2013 ROTATING ELECTRICAL MACHINES - PART 18-34: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR FORM-WOUND WINDINGS - EVALUATION OF THERMOMECHANICAL ENDURANCE OF INSULATION SYSTEMS
    I.S. EN 60034-5:2001 ROTATING ELECTRICAL MACHINES - PART 5: DEGREES OF PROTECTION PROVIDED BY THE INTEGRAL DESIGN OF ROTATING ELECTRICAL MACHINES (IP CODE) - CLASSIFICATION
    ISO 14990-1:2016 Earth-moving machinery — Electrical safety of machines utilizing electric drives and related components and systems — Part 1: General requirements
    I.S. EN 60034-3:2008 ROTATING ELECTRICAL MACHINES - PART 3: SPECIFIC REQUIREMENTS FOR SYNCHRONOUS GENERATORS DRIVEN BY STEAM TURBINES OR COMBUSTION GAS TURBINES
    ISO 17359:2018 Condition monitoring and diagnostics of machines — General guidelines
    I.S. EN 60034-28:2013 ROTATING ELECTRICAL MACHINES - PART 28: TEST METHODS FOR DETERMINING QUANTITIES OF EQUIVALENT CIRCUIT DIAGRAMS FOR THREE-PHASE LOW-VOLTAGE CAGE INDUCTION MOTORS (IEC 60034-28:2012 (EQV))
    I.S. EN 60349-2:2010 ELECTRIC TRACTION - ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 2: ELECTRONIC CONVERTER-FED ALTERNATING CURRENT MOTORS
    I.S. EN ISO 8528-13:2016 RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 13: SAFETY (ISO/DIS 8528-13:2014)
    ISO 13350:2015 Fans Performance testing of jet fans
    FM 1370 : 2018 CENTRIFUGAL FIRE PUMPS (VERTICAL SHAFT, TURBINE TYPE, BARREL)
    FM 1311 : 2018 CENTRIFUGAL FIRE PUMPS SPLIT-CASE TYPE (AXIAL OR RADIAL)
    GOST R 52350.15 : 2005 ELECTRICAL APPARATUS FOR EXPLOSIVE GAS ATMOSPHERES - PART 15: CONSTRUCTION, TEST AND MARKING OF TYPE OF PROTECTION "N" ELECTRICAL APPARATUS
    ISO/TS 19466:2017 Electrically propelled mopeds and motorcycles — Test method for evaluating performance of regenerative braking systems
    CEI EN 60034-22 : 2011 ROTATING ELECTRICAL MACHINES - PART 22: AC GENERATORS FOR RECIPROCATING INTERNAL COMBUSTION (RIC) ENGINE DRIVEN GENERATING SETS
    BWB TL 3405-0005 : 1ED 2004
    IEC TS 60034-20-1:2002 Rotating electrical machines - Part 20-1: Control motors - Stepping motors
    CSA C22.2 No. 61241-4 : 2012 ELECTRICAL APPARATUS FOR USE IN THE PRESENCE OF COMBUSTIBLE DUST - PART 4: TYPE OF PROTECTION 'PD'
    I.S. EN 60204-33:2011 SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 33: REQUIREMENTS FOR SEMICONDUCTOR FABRICATION EQUIPMENT
    UNE-EN 60034-18-31:2013 Rotating electrical machines - Part 18-31: Functional evaluation of insulation systems - Test procedures for form-wound windings - Thermal evaluation and classification of insulation systems used in rotating machines
    I.S. EN 61936-1:2010 POWER INSTALLATIONS EXCEEDING 1 KV A.C. - PART 1: COMMON RULES
    I.S. EN 12693:2008 REFRIGERATING SYSTEMS AND HEAT PUMPS - SAFETY AND ENVIRONMENTAL REQUIREMENTS - POSITIVE DISPLACEMENT REFRIGERANT COMPRESSORS
    I.S. EN 61800-4:2003 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 4: GENERAL REQUIREMENTS - RATING SPECIFICATIONS FOR A.C. POWER DRIVE SYSTEMS ABOVE 1000 V A.C. AND NOT EXCEEDING 35 KV
    I.S. EN 60034-18-1:2010 ROTATING ELECTRICAL MACHINES - PART 18-1: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - GENERAL GUIDELINES
    IEC 61800-9-2:2017 Adjustable speed electrical power drive systems - Part 9-2: Ecodesign for power drive systems, motor starters, power electronics and their driven applications - Energy efficiency indicators for power drive systems and motor starters
    IEC TR 62001-4:2016 High-voltage direct current (HVDC) systems - Guidance to the specification and design evaluation of AC filters - Part 4: Equipment
    IEC PAS 62001:2004 Guide to the specification and design evaluation of a.c. filters for HVDC systems
    IEC TS 61800-8:2010 Adjustable speed electrical power drive systems - Part 8: Specification of voltage on the power interface
    IEC TS 60034-17:2006 Rotating electrical machines - Part 17: Cage induction motors when fed from converters - Application guide
    IEC 61892-1:2015 Mobile and fixed offshore units - Electrical installations - Part 1: General requirements and conditions
    I.S. EN ISO 13709:2009 CENTRIFUGAL PUMPS FOR PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES
    DIN EN 328:2014-11 HEAT EXCHANGERS - FORCED CONVECTION UNIT AIR COOLERS FOR REFRIGERATION - TEST PROCEDURES FOR ESTABLISHING THE PERFORMANCE
    BS EN ISO 1680:2013 Acoustics. Test code for the measurement of airborne noise emitted by rotating electrical machines
    BS EN 13135-1 : 2003 CRANES - EQUIPMENT - PART 1: ELECTROTECHNICAL EQUIPMENT
    14/30297343 DC : 0 BS EN ISO 8528-13 - RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 13: SAFETY
    UNE-EN ISO 8528-13:2017 Reciprocating internal combustion engine driven alternating current generating sets - Part 13: Safety (ISO 8528-13:2016, Corrected version 2016-10-15)
    12/30266531 DC : 0 BS EN TS 62257-1 - RECOMMENDATIONS FOR SMALL RENEWABLE ENERGY AND HYBRID SYSTEMS FOR RURAL ELECTRIFICATION - PART 1: GENERAL INTRODUCTION TO RURAL ELECTRIFICATION
    IEC 61116:1992 Electromechanical equipment guide for small hydroelectric installations
    I.S.EN ISO 8528-13:2016&LC:2016 RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 13: SAFETY (ISO/DIS 8528-13:2014)
    IEC 60034-29:2008 Rotating electrical machines - Part 29: Equivalent loading and superposition techniques - Indirect testing to determine temperature rise
    IEC 60034-2-2:2010 Rotating electrical machines - Part 2-2: Specific methods for determining separate losses of large machines from tests - Supplement to IEC 60034-2-1
    IEC 61986:2002 Rotating electrical machines - Equivalent loading and super-position techniques - Indirect testing to determine temperature rise
    14/30293263 DC : 0 BS IEC 61892-1 ED 3.0 - MOBILE AND FIXED OFFSHORE UNITS - ELECTRICAL INSTALLATIONS - PART 1: GENERAL REQUIREMENTS AND CONDITIONS
    ISO 15783:2002 Seal-less rotodynamic pumps — Class II — Specification
    98/705686 DC : DRAFT MAR 1998 PREN 13135-1 - CRANES - SAFETY - DESIGN - REQUIREMENTS FOR EQUIPMENT - PART 1: ELECTROTECHNICAL EQUIPMENT
    14/30238347 DC : 0 BS EN 60204-1 ED 6.0 - SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS
    08/30195018 DC : DRAFT DEC 2008 BS EN 60204-33 - SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 33: REQUIREMENTS FOR SEMICONDUCTOR FABRICATION EQUIPMENT
    DD IEC/TS 61800-8:2010 Adjustable speed electrical power drive systems Specification of voltage on the power interface
    EN 61400-22:2011 Wind turbines - Part 22: Conformity testing and certification
    UNE-EN 60079-0:2013 Explosive atmospheres - Part 0: Equipment - General requirements
    UNE-EN 1175-1:1998 SAFETY OF INDUSTRIAL TRUCKS. ELECTRICAL REQUIREMENTS. PART 1: GENERAL REQUIREMENTS FOR BATTERY POWERED TRUCKS.
    UNE-EN 328:2015 Heat exchangers - Forced convection unit air coolers for refrigeration - Test procedures for establishing the performance
    IEC 60947-4-2:2011 Low-voltage switchgear and controlgear - Part 4-2: Contactors and motor-starters - AC semiconductor motor controllers and starters
    BS EN ISO 8528-13:2016 Reciprocating internal combustion engine driven alternating current generating sets Safety
    BS ISO 19372:2015 Microturbines applications. Safety
    IEC 61058-2-4:1995+AMD1:2003 CSV Switches for appliances - Part 2-4: Particular requirements for independently mounted switches
    ISO 1680:2013 Acoustics — Test code for the measurement of airborne noise emitted by rotating electrical machines
    IEC 60027-4:2006 Letter symbols to be used in electrical technology - Part 4: Rotating electric machines
    UNE-EN 327:2015 Heat exchangers - Forced convection air cooled refrigerant condensers - Test procedures for establishing performance
    BS ISO 19859:2016 Gas turbine applications. Requirements for power generation
    BS EN 14492-1 : 2006 CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 1: POWER DRIVEN WINCHES
    ISO 22734-2:2011 Hydrogen generators using water electrolysis process Part 2: Residential applications
    IEC 60034-5:2000+AMD1:2006 CSV Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification
    IEC 60034-18-34:2012 Rotating electrical machines - Part 18-34: Functional evaluation of insulation systems - Test procedures for form-wound windings - Evaluation of thermomechanical endurance of insulation systems
    IEC 60034-2-1:2014 Rotating electrical machines - Part 2-1: Standard methods for determining losses and efficiency from tests (excluding machines for traction vehicles)
    IEC 60034-18-21:2012 Rotating electrical machines - Part 18-21: Functional evaluation of insulation systems - Test procedures for wire-wound windings - Thermal evaluation and classification
    IEC 60034-18-31:2012 Rotating electrical machines - Part 18-31: Functional evaluation of insulation systems - Test procedures for form-wound windings - Thermal evaluation and classification of insulation systems used in rotating machines
    IEC 60034-9:2003+AMD1:2007 CSV Rotating electrical machines - Part 9: Noise limits
    IEC 61800-1:1997 Adjustable speed electrical power drive systems - Part 1: General requirments - Rating specifications for low voltage adjustables speed d.c. power drive systems
    BS EN 61936-1 : 2010 POWER INSTALLATIONS EXCEEDING 1 KV A.C - PART 1: COMMON RULES
    IEC 60349-4:2012 Electric traction - Rotating electrical machines for rail and road vehicles - Part 4: Permanent magnet synchronous electrical machines connected to an electronic converter
    BS EN 60204-33:2011 Safety of machinery. Electrical equipment of machines Requirements for semiconductor fabrication equipment
    IEC 60349-1:2010 Electric traction - Rotating electrical machines for rail and road vehicles - Part 1: Machines other than electronic converter-fed alternating current motors
    UNE-EN 60349-1:2011 Electric traction - Rotating electrical machines for rail and road vehicles -- Part 1: Machines other than electronic converter-fed alternating current motors
    IEC 60034-28:2012 Rotating electrical machines - Part 28: Test methods for determining quantities of equivalent circuit diagrams for three-phase low-voltage cage induction motors
    BS ISO 14990-1:2016 Earth-moving machinery. Electrical safety of machines utilizing electric drives and related components and systems General requirements
    UNE-EN 61936-1:2012 Power installations exceeding 1 kV a.c. -- Part 1: Common rules
    09/30150663 DC : 0 BS ISO 22734-2 - HYDROGEN GENERATORS USING WATER ELECTROLYSIS PROCESS - PART 2: RESIDENTIAL APPLICATIONS
    BS EN 14161 : 2011 PETROLEUM AND NATURAL GAS INDUSTRIES - PIPELINE TRANSPORTATION SYSTEMS (ISO 13623:2009 MODIFIED)
    12/30260546 DC : 0 BS EN 50156-1 - ELECTRICAL EQUIPMENT FOR FURNACES AND ANCILLARY EQUIPMENT - PART 1: REQUIREMENTS FOR APPLICATION DESIGN AND INSTALLATION
    BS ISO 22734-2:2011 Hydrogen generators using water electrolysis process Residential applications
    07/30153021 DC : 0 BS IEC 60204-33 - SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 33: REQUIREMENTS FOR SEMICONDUCTOR FABRICATION EQUIPMENT
    EN 60027-4:2007 Letter symbols to be used in electrical technology - Part 4: Rotating electrical machines
    CEI 18-61 : 2013 MOBILE AND FIXED OFFSHORE UNITS - ELECTRICAL INSTALLATIONS - PART 1: GENERAL REQUIREMENTS AND CONDITIONS
    DIN 56950:2005-04 ENTERTAINMENT TECHNOLOGY - MACHINERY INSTALLATIONS - SAFETY REQUIREMENTS AND TESTING
    EN ISO 13709:2009 Centrifugal pumps for petroleum, petrochemical and natural gas industries (ISO 13709:2009)
    EN 327:2014 Heat exchangers - Forced convection air cooled refrigerant condensers - Test procedures for establishing performance
    EN 15268:2008 Petrol filling stations - Safety requirements for the construction of submersible pump assemblies
    EN 88528-11 : 2004 RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 11: ROTARY UNINTERRUPTIBLE POWER SYSTEMS - PERFORMANCE REQUIREMENTS AND TEST METHODS
    EN 14492-1:2006+A1:2009/AC:2010 CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 1: POWER DRIVEN WINCHES
    EN ISO 15783:2003/A1:2008 Seal-less rotodynamic pumps - Class II - Specification - Amendment 1 (ISO 15783:2003/Amd 1:2008)
    EN ISO 5802:2008/A1:2015 INDUSTRIAL FANS - PERFORMANCE TESTING IN SITU (ISO 5802:2001/AMD 1:2015)
    EN 45510-2-5:2002 Guide for procurement of power station equipment - Part 2-5: Electrical equipment - Motors
    EN ISO 1680:2013 Acoustics - Test code for the measurement of airborne noise emitted by rotating electrical machines (ISO 1680:2013)
    EN 14161:2011+A1:2015 Petroleum and natural gas industries - Pipeline transportation systems (ISO 13623:2009 modified)
    EN 15194:2017 Cycles - Electrically power assisted cycles - EPAC Bicycles
    EN 14492-2:2006+A1:2009/AC:2010 CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 2: POWER DRIVEN HOISTS
    EN ISO 13350:2015 Fans - Performance testing of jet fans (ISO 13350:2015)
    DD CLC/TS 50537-2:2010 Railway applications. Mounted parts of the traction transformer and cooling system Pump for insulating liquid for traction transformers and reactors
    UNE-EN 60079-1:2015 Explosive atmospheres - Part 1: Equipment protection by flameproof enclosures "d"
    BS EN 61800-2:2015 Adjustable speed electrical power drive systems General requirements. Rating specifications for low voltage adjustable speed a.c. power drive systems
    UNE-EN 60079-15:2013 Explosive atmospheres - Part 15: Equipment protection by type of protection "n"
    BS EN 88528-11:2004 Reciprocating internal combustion engine driven alternating current generating sets Rotary uninterruptible power systems. Performance requirements and test methods
    BS ISO 8528-8:2016 Reciprocating internal combustion engine driven alternating current generating sets Requirements and tests for low-power generating sets
    BS EN 60947-6-2:2003 Low-voltage switchgear and controlgear Multiple function equipment. Control and protective switching devices (or equipment) (CPS)
    CEI EN 60034-30-1 : 2015 ROTATING ELECTRICAL MACHINES - PART 30-1: EFFICIENCY CLASSES OF LINE OPERATED AC MOTORS (IE CODE)
    BS EN 60947-4-2:2012 Low-voltage switchgear and controlgear Contactors and motor-starters. AC semiconductor motor controllers and starters
    BS EN 50598-2 : 2014 ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS & THEIR DRIVEN APPLICATIONS - PART 2: ENERGY EFFICIENCY INDICATORS FOR POWER DRIVE SYSTEMS AND MOTOR STARTERS
    DIN ISO 8528-3:1997-11 RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 3: ALTERNATING CURRENT GENERATORS FOR GENERATING SETS
    BIS IS/IEC 60079-1 : 2007 EXPLOSIVE ATMOSPHERES - PART 1: EQUIPMENT PROTECTION BY FLAMEPROOF ENCLOSURES 'D'
    CSA C22.3 No. 61936-1 : 2008 : R2015 POWER INSTALLATIONS EXCEEDING 1 KV A.C. - PART 1: COMMON RULES
    BS ISO 21927-3 : 2006 SMOKE AND HEAT CONTROL SYSTEMS - PART 3: SPECIFICATION FOR POWERED SMOKE AND HEAT EXHAUST VENTILATORS
    BS EN 50216-12:2011 Power transformer and reactor fittings Fans
    15/30314544 DC : 0 BS EN 61800-9-1 - ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 9-1: ENERGY EFFICIENCY OF POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS AND THEIR DRIVEN APPLICATIONS - GENERAL REQUIREMENTS FOR SETTING ENERGY EFFICIENCY STANDARDS FOR POWER DRIVEN EQUIPMENT USING THE EXTENDED PRODUCT APPROACH (EPA) AND SEMI ANALYTIC MODEL (SAM)
    ISO 3977-8:2002 Gas turbines — Procurement — Part 8: Inspection, testing, installation and commissioning
    08/30176383 DC : DRAFT JAN 2008 BS EN 60034-18-1 - ROTATING ELECTRICAL MACHINES - PART 18-1: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - GENERAL GUIDELINES
    01/202454 DC : DRAFT APRIL 2001 IEC 60034-14 ED.4 - ROTATING ELECTRICAL MACHINERY - PART 14: MECHANICAL VIBRATION OF CERTAIN MACHINES WITH SHAFT HEIGHTS 56 MM AND HIGHER - MEASUREMENT, EVALUATION AND LIMITS OF VIBRATION SEVERITY
    08/30191891 DC : DRAFT OCT 2008 BS EN 61936-1 - POWER INSTALLATIONS EXCEEDING 1 KV A.C. - PART 1: COMMON RULES
    CEI 301-1 : 1997 ELECTRIC DRIVES - DICTIONARY
    03/316173 DC : DRAFT SEP 2003 ISO 8528-4 - RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 4: CONTROLGEAR AND SWITCHGEAR
    EN IEC 61058-1:2018 Switches for appliances - Part 1: General requirements
    I.S. EN 60034-29:2008 ROTATING ELECTRICAL MACHINES - PART 29: EQUIVALENT LOADING AND SUPERPOSITION TECHNIQUES - INDIRECT TESTING TO DETERMINE TEMPERATURE RISE
    10/30200372 DC : 0 BS ISO 17359 - CONDITION MONITORING AND DIAGNOSTICS OF MACHINES - GENERAL GUIDELINES
    DD IEC/TS 62257-7-3:2008 Recommendations for small renewable energy and hybrid systems for rural electrification Generator set. Selection of generator sets for rural electrification systems
    BS EN 60694:1997 Common specifications for high-voltage switchgear and controlgear standards
    API 675 : 2012 POSITIVE DISPLACEMENT PUMPS - CONTROLLED VOLUME FOR PETROLEUM, CHEMICAL, AND GAS INDUSTRY SERVICES
    10/30187796 DC : DRAFT DEC 2010 BS EN 14161 - PETROLEUM AND NATURAL GAS INDUSTRIES - PIPELINE TRANSPORTATION SYSTEMS
    14/30300075 DC : 0 BS EN 60034-12 ED 3.0 - ROTATING ELECTRICAL MACHINES - PART 12: STARTING PERFORMANCE OF SINGLE-SPEED THREE-PHASE CAGE INDUCTION MOTORS
    CEI EN 60034-15 : 2009 ROTATING ELECTRICAL MACHINES - PART 15: IMPULSE VOLTAGE WITHSTAND LEVELS OF FORM-WOUND STATOR COILS FOR ROTATING A.C. MACHINES
    BS EN 50598-1:2014 Ecodesign for power drive systems, motor starters, power electronics & their driven applications General requirements for setting energy efficiency standards for power driven equipment using the extended product approach (EPA), and semi analytic model (SAM)
    OVE/ONORM EN 60034-5 : 2007 ROTATING ELECTRICAL MACHINES - PART 5: DEGREES OF PROTECTION PROVIDED BY THE INTEGRAL DESIGN OF ROTATING ELECTRICAL MACHINES (IP CODE) - CLASSIFICATION
    11/30206274 DC : 0 BS EN 60349-4 - ELECTRIC TRACTION ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 4: PERMANENT MAGNET SYNCHRONOUS ELECTRICAL MACHINES CONNECTED TO AN ELECTRONIC CONVERTER
    PD IEC/TR 62001-4:2016 High-voltage direct current (HVDC) systems. Guidance to the specification and design evaluation of AC filters Equipment
    NF EN 60034 18-1 : 2010 ROTATING ELECTRICAL MACHINES - PART 18-1: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - GENERAL GUIDELINES
    I.S. EN 61116:1995 ELECTROMECHANICAL EQUIPMENT GUIDE FOR SMALL HYDROELECTRIC INSTALLATIONS
    UNE-EN 60034-28:2013 Rotating electrical machines - Part 28: Test methods for determining quantities of equivalent circuit diagrams for three-phase low-voltage cage induction motors
    BS EN 60034-4:2008 Rotating electrical machines Methods for determining synchronous machine quantities from tests
    I.S. EN 60079-14:2014 EXPLOSIVE ATMOSPHERES - PART 14: ELECTRICAL INSTALLATIONS DESIGN, SELECTION AND ERECTION
    11/30247086 DC : 0 BS EN 60079-1 ED. 7.0 - EXPLOSIVE ATMOSPHERES - PART 1: EQUIPMENT PROTECTION BY FLAMEPROOF ENCLOSURES "D"
    UNE-EN 60027-4:2011 Letter symbols to be used in electrical technology -- Part 4: Rotating electric machines
    CSA E60079.7 : 2003 ELECTRICAL APPARATUS FOR EXPLOSIVE GAS ATMOSPHERES - PART 7: INCREASED SAFETY "E"
    PD IEC/TS 60034-32:2016 Rotating electrical machines Measurement of stator end-winding vibration at form-wound windings
    BS ISO 8528-3:2005 Reciprocating internal combustion engine driven alternating current generating sets Alternating current generators for generating sets
    UNE-EN 50598-2:2015 Ecodesign for power drive systems, motor starters, power electronics & their driven applications - Part 2: Energy efficiency indicators for power drive systems and motor starters
    09/30194359 DC : 0 BS EN 60034-18-34 - ROTATING ELECTRICAL MACHINES - PART 18-34: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR FORM-WOUND WINDINGS - EVALUATION OF THERMOMECHANICAL ENDURANCE OF INSULATION SYSTEMS
    ISO 1680-2:1986 Acoustics Test code for the measurement of airborne noise emitted by rotating electrical machinery Part 2: Survey method
    NF EN 60947-4-2 : 2012 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 4-2: CONTACTORS AND MOTOR-STARTERS - A.C. SEMICONDUCTOR MOTOR CONTROLLERS AND STARTERS
    CSA E60079.15 : 2002 ELECTRICAL APPARATUS FOR EXPLOSIVE GAS ATMOSPHERES - ELECTRICAL APPARATUS WITH TYPE OF PROTECTION "n"
    08/30180328 DC : DRAFT MAR 2008 BS EN 61800-8 - ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 8: SPECIFICATION OF VOLTAGE ON THE POWER INTERFACE
    UNE-EN 15714-2:2010 Industrial valves - Actuators - Part 2: Electric actuators for industrial valves - Basic requirements
    BS EN 60034-9:2005 Rotating electrical machines Noise limits
    09/30182101 DC : 0 BS EN 60349-1 - ELECTRICAL TRACTION - ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 1: MACHINES OTHER THAN ELECTRONIC CONVERTOR-FED ALTERNATING CURRENT MOTORS
    I.S. EN 60349-4:2013 ELECTRIC TRACTION - ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 4: PERMANENT MAGNET SYNCHRONOUS ELECTRICAL MACHINES CONNECTED TO AN ELECTRONIC CONVERTER (IEC 60349-4:2012 (EQV))
    BIS IS/IEC 60079-7 : 2006 EXPLOSIVE ATMOSPHERES - PART 7: EQUIPMENT PROTECTION BY INCREASED SAFETY 'E'
    CEI EN 60034-2-2 : 2011 ROTATING ELECTRICAL MACHINES - PART 2-2: SPECIFIC METHODS FOR DETERMINING SEPARATE LOSSES OF LARGE MACHINES FROM TESTS - SUPPLEMENT TO IEC 60034-2-1
    DIN EN 15714-2:2010-02 Industrial valves - Actuators - Part 2: Electric actuators for industrial valves - Basic requirements
    FM 1319 : 2018 CENTRIFUGAL FIRE PUMPS (HORIZONTAL, END SUCTION TYPE)
    BIS IS/IEC 60079-31 : 2008 EXPLOSIVE ATMOSPHERES - PART 31: EQUIPMENT DUST IGNITION PROTECTION BY ENCLOSURE "T"
    IEEE 45.6-2016 IEEE Recommended Practice for Electrical Installations on Shipboard--Electrical Testing
    ISO 50004:2014 Energy management systems Guidance for the implementation, maintenance and improvement of an energy management system
    IEC 60092-501:2013 Electrical installations in ships - Part 501: Special features - Electric propulsion plant
    GOST R ISO 8528-1 : 2005 RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 1: APPLICATION, RATINGS AND PERFORMANCE
    IEC TS 60034-2-3:2013 Rotating electrical machines - Part 2-3: Specific test methods for determining losses and efficiency of converter-fed AC induction motors
    CSA C22.3 No. 61936-1 : 2008 POWER INSTALLATIONS EXCEEDING 1 KV A.C. - PART 1: COMMON RULES
    IEEE 841-2009 IEEE Standard for Petroleum and Chemical Industry--Premium-Efficiency, Severe-Duty, Totally Enclosed Fan-Cooled (TEFC) Squirrel Cage Induction Motors--Up to and Including 370 kW (500 hp)
    I.S. EN ISO 13350:2015 FANS - PERFORMANCE TESTING OF JET FANS (ISO 13350:2015)
    I.S. EN 60034-14:2004 ROTATING ELECTRICAL MACHINES - PART 14: MECHANICAL VIBRATION OF CERTAIN MACHINES WITH SHAFT HEIGHTS 56 MM AND HIGHER - MEASUREMENT, EVALUATION AND LIMITS OF VIBRATION SEVERITY
    I.S. EN 60947-4-1:2010 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 4-1: CONTACTORS AND MOTOR-STARTERS - ELECTROMECHANICAL CONTACTORS AND MOTOR-STARTERS (IEC 60947-4-1:2009 (EQV))
    NF EN 60034-14 : 2004 AMD 1 2007 ROTATING ELECTRICAL MACHINES - PART 14: MECHANICAL VIBRATION OF CERTAIN MACHINES WITH SHAFT HEIGHTS 56 MM AND HIGHER - MEASUREMENT, EVALUATION AND LIMITS OF VIBRATION SEVERITY
    ISO 1680-1:1986 Acoustics Test code for the measurement of airborne noise emitted by rotating electrical machinery Part 1: Engineering method for free-field conditions over a reflecting plane
    BS IEC 61892-5:2014 Mobile and fixed offshore units. Electrical installations Mobile units
    NF EN 61800 5-1 : 2007 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 5-1: SAFETY REQUIREMENTS - ELECTRICAL, THERMAL AND ENERGY
    I.S. EN 60034-19:2014 ROTATING ELECTRICAL MACHINES - PART 19: SPECIFIC TEST METHODS FOR D.C. MACHINES ON CONVENTIONAL AND RECTIFIER-FED SUPPLIES
    I.S. EN 50598-2:2014 ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS & THEIR DRIVEN APPLICATIONS - PART 2: ENERGY EFFICIENCY INDICATORS FOR POWER DRIVE SYSTEMS AND MOTOR STARTERS
    BS IEC 61892-1:2015 Mobile and fixed offshore units. Electrical installations General requirements and conditions
    ISO 18652:2005 Building construction machinery and equipment External vibrators for concrete
    UNE-EN 60034-22:2010 Rotating electrical machines -- Part 22: AC generators for reciprocating internal combustion (RIC) engine driven generating sets
    BIS IS/IEC 60947-4-1 : 2000 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 4: CONTACTORS AND MOTOR-STARTERS - SECTION 1: ELECTROMECHANICAL CONTACTORS AND MOTOR-STARTERS
    NF EN 61986 : 2004 ROTATING ELECTRICAL MACHINES - EQUIVALENT LOADING AND SUPER-POSITION TECHNIQUES - INDIRECT TESTING TO DETERMINE TEMPERATURE RISE
    NF EN 60034-11 : 2005 ROTATING ELECTRICAL MACHINES - PART 11: THERMAL PROTECTION
    CEI EN 61800-4 : 2003 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 4: GENERAL REQUIREMENTS - RATING SPECIFICATIONS FOR A/C/ POWER DRIVE SYSTEMS ABOVE 1000 V A.C. AND NOT EXCEEDING 35 KV
    UNE-EN 60079-7:2016 Explosive atmospheres - Part 7: Equipment protection by increased safety "e"
    I.S. EN 60027-4:2007 LETTER SYMBOLS TO BE USED IN ELECTRIC TECHNOLOGY - PART 4: ROTATING ELECTRIC MACHINES
    ISO 8528-3:2005 Reciprocating internal combustion engine driven alternating current generating sets Part 3: Alternating current generators for generating sets
    I.S. EN 61400-22:2011 WIND TURBINES - PART 22: CONFORMITY TESTING AND CERTIFICATION
    I.S. EN ISO 5802:2008 INDUSTRIAL FANS - PERFORMANCE TESTING IN SITU (ISO 5802:2001)
    I.S. EN 60034-4:2008 ROTATING ELECTRICAL MACHINES - PART 4: METHODS FOR DETERMINING SYNCHRONOUS MACHINE QUANTITIES FROM TESTS
    I.S. EN 61800-2:2015 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 2: GENERAL REQUIREMENTS - RATING SPECIFICATIONS FOR LOW VOLTAGE ADJUSTABLE SPEED A.C. POWER DRIVE SYSTEMS
    I.S. EN 62271-1:2017 HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 1: COMMON SPECIFICATIONS FOR ALTERNATING CURRENT SWITCHGEAR AND CONTROLGEAR
    IEC 61972:2002 Method for determining losses and efficiency of three-phase cage induction motors
    DIN EN 14492-2:2016-08 (Draft) CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 2: POWER DRIVEN HOISTS
    DIN EN 14492-1:2015-05 (Draft) Cranes - Power driven winches & hoists - part 1 power driven winches; German and English version prEN 14492-1:2015
    13/30294120 DC : 0 BS IEC 61892-5 ED 3.0 - MOBILE AND FIXED OFFSHORE UNITS - ELECTRICAL INSTALLATIONS - PART 5: MOBILE UNITS
    BS EN 328:2014 Heat exchangers. Forced convection unit air coolers for refrigeration. Test procedures for establishing the performance
    BS ISO 22734-1:2008 Hydrogen generators using water electrolysis process Industrial and commercial applications
    BS 7698-8:1996 Reciprocating internal combustion engine driven alternating current generating sets Requirements and tests for low-power generating sets
    PD ISO/TR 18569:2004 Safety of machinery. Guidelines for the understanding and use of safety of machinery standards.
    02/203840 DC : DRAFT MAY 2002 IEC 60204-1/ED.5.0 - SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS
    IEC 60204-32:2008 Safety of machinery - Electrical equipment of machines - Part 32: Requirements for hoisting machines
    12/30269297 DC : 0 BS EN 60079-14/ED 5 - EXPLOSIVE ATMOSPHERES - PART 14: ELECTRICAL INSTALLATIONS DESIGN, SELECTION AND ERECTION
    BS EN ISO 15783 : 2003 SEAL-LESS ROTODYNAMIC PUMPS - CLASS 2 - SPECIFICATION
    ISO 22734-1:2008 Hydrogen generators using water electrolysis process Part 1: Industrial and commercial applications
    IEC 60034-30:2008 Rotating electrical machines - Part 30: Efficiency classes of single-speed, three-phase, cage-induction motors (IE-code)
    13/30286778 DC : 0 BS EN 60079-1 - EXPLOSIVE ATMOSPHERES - PART 1: EQUIPMENT PROTECTION BY FLAMEPROOF ENCLOSURES 'D'
    BS EN 327:2014 Heat exchangers. Forced convection air cooled refrigerant condensers. Test procedures for establishing performance
    IEC 61400-22:2010 Wind turbines - Part 22: Conformity testing and certification
    BS EN 60204-1 : 2006 SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS
    IEC 60947-6-2:2002+AMD1:2007 CSV Low-voltage switchgear and controlgear - Part 6-2: Multiple function equipment - Control and protective switching devices (or equipment) (CPS)
    BS EN ISO 14224:2016 Petroleum, petrochemical and natural gas industries. Collection and exchange of reliability and maintenance data for equipment
    BS EN 60204-32:2008 Safety of machinery. Electrical equipment of machines Requirements for hoisting machines
    ISO 13709:2009 Centrifugal pumps for petroleum, petrochemical and natural gas industries
    BS EN 14492-2 : 2006 CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 2: POWER DRIVEN HOISTS
    IEC 60034-18-1:2010 Rotating electrical machines - Part 18-1: Functional evaluation of insulation systems - General guidelines
    15/30322229 DC : 0 BS EN 61800-5-1:2007/AMD 1 - ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 5-1: SAFETY REQUIREMENTS - ELECTRICAL, THERMAL AND ENERGY
    IEC 61241-4:2001 Electrical apparatus for use in the presence of combustible dust - Part 4: Type of protection "pD"
    IEC 60079-0:2017 RLV Explosive atmospheres - Part 0: Equipment - General requirements
    DIN EN 12693:2008-09 REFRIGERATING SYSTEMS AND HEAT PUMPS - SAFETY AND ENVIRONMENTAL REQUIREMENTS - POSITIVE DISPLACEMENT REFRIGERANT COMPRESSORS
    EN 60079-0:2012/A11:2013 EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS (IEC 60079-0:2011, MODIFIED)
    DIN EN 14492-2:2010-05 CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 2: POWER DRIVEN HOISTS
    EN 13135-1:2003+A1:2010 Cranes - Equipment - Part 1: Electrotechnical equipment
    DIN EN 1151-1:2006-11 PUMPS - ROTODYNAMIC PUMPS - CIRCULATION PUMPS HAVING A RATED POWER INPUT NOT EXCEEDING 200 W FOR HEATING INSTALLATIONS AND DOMESTIC HOT WATER INSTALLATIONS - PART 1: NON-AUTOMATIC CIRCULATION PUMPS, REQUIREMENTS, TESTING, MARKING
    UNE-ISO 22734-1:2012 Hydrogen generators using water electrolysis process. Part 1: Industrial and commercial applications
    EN 60349-4:2013 Electric traction - Rotating electrical machines for rail and road vehicles - Part 4: Permanent magnet synchronous electrical machines connected to an electronic converter
    EN 60034-19:2014 Rotating electrical machines - Part 19: Specific test methods for d.c. machines on conventional and rectifier-fed supplies
    CEI 18-62 : 2013 MOBILE AND FIXED OFFSHORE UNITS - ELECTRICAL INSTALLATIONS - PART 5: MOBILE UNITS
    ISA 60079-0 : 2005 EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS
    EN 60034-28:2013 Rotating electrical machines - Part 28: Test methods for determining quantities of equivalent circuit diagrams for three-phase low-voltage cage induction motors
    EN 61800-4:2003 Adjustable speed electrical power drive systems - Part 4: General requirements - Rating specifications for a.c. power drive systems above 1 000 V a.c. and not exceeding 35 kV
    EN 1151-1:2006/AC:2007 PUMPS - ROTODYNAMIC PUMPS - CIRCULATION PUMPS HAVING A RATED POWER INPUT NOT EXCEEDING 200 W FOR HEATING INSTALLATIONS AND DOMESTIC HOT WATER INSTALLATIONS - PART 1: NON-AUTOMATIC CIRCULATION PUMPS, REQUIREMENTS, TESTING, MARKING
    EN 60204-32:2008 Safety of machinery - Electrical equipment of machines - Part 32: Requirements for hoisting machines
    EN 60204-33:2011 Safety of machinery - Electrical equipment of machines - Part 33: Requirements for semiconductor fabrication equipment
    EN 60349-1:2010 Electric traction - Rotating electrical machines for rail and road vehicles - Part 1: Machines other than electronic converter-fed alternating current motors
    EN 60079-1:2014 Explosive atmospheres - Part 1: Equipment protection by flameproof enclosures "d"
    EN 50019:2000/corrigendum Apr. 2003 ELECTRICAL APPARATUS FOR POTENTIALLY EXPLOSIVE ATMOSPHERES - INCREASED SAFETY "E"
    EN 50598-2:2014/A1:2016 ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS & THEIR DRIVEN APPLICATIONS - PART 2: ENERGY EFFICIENCY INDICATORS FOR POWER DRIVE SYSTEMS AND MOTOR STARTERS
    EN 61986:2002 Rotating electrical machines - Equivalent loading and super-position techniques - Indirect testing to determine temperature rise
    CLC/TS 60034-25:2008 Rotating electrical machines - Part 25: Guidance for the design and performance of a.c. motors specifically designed for converter supply
    EN 60034-30:2009 Rotating electrical machines - Part 30: Efficiency classes of single-speed, three-phase, cage-induction motors (IE-code)
    EN 60034-29:2008 Rotating electrical machines - Part 29: Equivalent loading and superposition techniques - Indirect testing to determine temperature rise
    EN 60034-18-21:2013 Rotating electrical machines - Part 18-21: Functional evaluation of insulation systems - Test procedures for wire-wound windings - Thermal evaluation and classification
    EN 61241-4:2006 Electrical apparatus for use in the presence of combustible dust - Part 4: Type of protection "pD"
    CEI 18-58 : 2013 MOBILE AND FIXED OFFSHORE UNITS - ELECTRICAL INSTALLATIONS - PART 3: EQUIPMENT
    EN 61116:1994 Electromechanical equipment guide for small hydroelectric installations
    EN 60349-2:2010 ELECTRIC TRACTION - ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 2: ELECTRONIC CONVERTER-FED ALTERNATING CURRENT MOTORS
    DIN EN ISO 15783:2010-04 Seal-less rotodynamic pumps - Class II - Specification (ISO 15783:2002 + Amd.1:2008) (includes Amendment A1:2008)
    EN 60034-4:2008 Rotating electrical machines - Part 4: Methods for determining synchronous machine quantities from tests

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60038:2009 IEC standard voltages
    IEC 60034-9:2003+AMD1:2007 CSV Rotating electrical machines - Part 9: Noise limits
    IEC 60050-811:1991 International Electrotechnical Vocabulary (IEV) - Part 811: Electric traction
    IEC 60034-29:2008 Rotating electrical machines - Part 29: Equivalent loading and superposition techniques - Indirect testing to determine temperature rise
    IEC 61293:1994 Marking of electrical equipment with ratings related to electrical supply - Safety requirements
    IEC 60050-411:1996 International Electrotechnical Vocabulary (IEV) - Part 411: Rotating machinery
    IEC 60204-1:2016 Safety of machinery - Electrical equipment of machines - Part 1: General requirements
    IEC 61148:2011 Terminal markings for valve device stacks and assemblies and for power conversion equipment
    IEC 60204-11:2000 Safety of machinery - Electrical equipment of machines - Part 11: Requirements for HV equipment for voltages above 1 000 V a.c. or 1 500 V d.c. and not exceeding 36 kV
    IEC 60034-3:2007 Rotating electrical machines - Part 3: Specific requirements for synchronous generators driven by steam turbines or combustion gas turbines
    IEC 60027-1:1992 Letters symbols to be used in electrical technology - Part 1: General
    IEC 60085:2007 Electrical insulation - Thermal evaluation and designation
    IEC 60034-8:2007+AMD1:2014 CSV Rotating electrical machines - Part 8: Terminal markings anddirection of rotation
    IEC TS 60034-25:2014 Rotating electrical machines - Part 25: AC electrical machines used in power drive systems - Application guide
    IEC 60034-14:2003+AMD1:2007 CSV Rotating electrical machines - Part 14: Mechanical vibration of certain machines with shaft heights 56 mm and higher - Measurement, evaluation and limits of vibration severity
    IEC 60034-18-41:2014 Rotating electrical machines - Part 18-41: Partial discharge free electrical insulation systems (Type I) used in rotating electrical machines fed from voltage converters - Qualification and quality control tests
    IEC 60034-12:2016 Rotating electrical machines - Part 12: Starting performance of single-speed three-phase cage induction motors
    CISPR 11:2015 RLV Industrial, scientific and medical equipment - Radio-frequency disturbance characteristics - Limits and methods of measurement
    IEC 60027-4:2006 Letter symbols to be used in electrical technology - Part 4: Rotating electric machines
    IEC 60060-1:2010 High-voltage test techniques - Part 1: General definitions and test requirements
    IEC 60445:2017 Basic and safety principles for man-machine interface, marking and identification - Identification of equipment terminals, conductor terminations and conductors
    IEC 60664-1:2007 Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective